KENSUN HID AUTOMOTIVE HEAD LAMP CONVERSION KIT INSTALLATION MANUAL
|
|
- Branden Thomas Walters
- 7 years ago
- Views:
Transcription
1 1
2 KENSUN HID AUTOMOTIVE HEAD LAMP CONVERSION KIT INSTALLATION MANUAL 2
3 CONTENTS A. Before installing (page 4) B. Installing the bulbs (page 6) C. Installing the ballasts (page 8) D. For Bi Xenon kits only: Installing the relay harness (page 9) E. After installation (page 10) F. Warnings and correct usage information (page 11) APPENDIX 1 Modifications needed for some vehicle models (page 12) APPENDIX 2 Trouble shooting (page 13) APPENDIX wiring issue (page 15) APPENDIX 4 Aligning your headlights (page 16) 3
4 KENSUN H.I.D HEADLIGHT INSTALLATION MANUAL Thank you for purchasing your KENSUN HID light kit. Most vehicles are compatible with our kits however there are variations for each car, make and model. Please check Appendix 1 for any modifications that may be needed for your vehicle for correct running of the kit. Also please refer to our Trouble shooting in Appendix 2 that may address any difficulties you have with installation. GENERAL WARNING - This is a system that produces high voltage electricity. Installation by an inexperienced person is not recommended. Be sure to consult a professional technician for installation. Faulty or insecure installation can result in electrical problems and shock. A. Before Installing Please read this installation guide carefully before installing the system. For most vehicles installation is straight forward. 1. For safety please wait for the car lighting and engine to cool down completely before attempting to install the HID lights. 2. Place the vehicle in either the N or P gear and make certain the lighting switch in the vehicle is off before starting installation. 3. Avoid unnecessary or rough handling of bulbs. It is advised to wear gloves while installing the kit. Touching the bulbs with bare fingers may cause oil spots. If the bulbs are not clean you may wipe the bulbs with a dry cloth or rubbing alcohol, however don t immerse in any liquid. 4. DRLs, alarm lights and auto headlights must be disabled prior to installation. 5. Make sure that you have the correct kit for your vehicle. The HID kit must be the same bulb size as the original halogen bulb. Dual beam kits can only be used when the halogen bulb was dual beam (dual filament). 6. Know what type of kit you are installing. There are three types of kits; single beam, low beam HID-high beam halogen and bi xenon. The single beam has no high beam. The low HID / high halogen has a HID bulb for the low beam and a halogen bulb for the high beam. The Bi Xenon kit has one HID bulb that moves inward for high beam, so both the high and low beams are HID. 4
5 COMPONENTS: 5
6 B. Installing the Bulbs 1. You can open the hood, remove the dust cap and remove the original bulbs from the headlight housing. If there is not enough room you may need to remove the headlight housing assembly to continue with the installation 2. Your Kensun bulbs come well packed so they should not be damaged in shipping. All the protective packaging should be removed. Remove the plastic cap covering the HID bulb being careful not to hit the vacuum tube. If your bulb has a plastic washer, it too will have to be removed. To remove the washer; remove the red rubber grommet, remove the plastic ring and then roll back the grommet until it is under the ledge, as in the pictures below 6
7 3. Place the HID headlights into the headlight housing. The bulb should go in the same location that your halogen bulbs had been in originally. (For some vehicles, size H1 and H7 bulbs may require a bulb holder to replace the factory bulb holder. This is not included in the kit) 4. OPTIONAL: Seal tight with the dust cover. Our bulbs come with a black rubber grommet around the wires before the bulb, to weather seal your lights with the dust cover. Drill a hole in the middle of the back dust cap with a 1 cutter. Slide the plug end of the wires through the dust cap and fit the grommet into the hole that you drilled. 7
8 C. Installing the Ballasts HID bulbs will not work without the ballast to ignite and uphold the power supply. Unless you have a factory HID system preinstalled you will not be able to install the HID lights without ballasts. Fix the ballasts to any solid place in the engine cavity close to the headlights using the fixing brackets. You can also use zip ties and double sided tape if needed. Avoid placing ballasts next to parts that operate at high temperatures. The single beam HID kits plug directly from the ballasts to the bulbs. 8
9 D. For Bi Xenon Only: Installing the Relay Harness At this stage you will need to install the relay harness. There are eight connections to complete in order to install the harness and connect the power supply: A & B. Connect to the In port on the left and right ballasts. C. Connects to plug of your vehicle s halogen bulb on either the left or right side. D & E. Connect to left and right HID bulbs ports. F & G. Connect to car body as an earth. H. Connects to the positive terminal of the battery. 9
10 E. After Installation Make certain that all connections are tight and secure Make certain that all parts dismantled beforehand are returned to their original places. Check that other vehicle parts are going correctly (e.g. lamps, sound systems, wind screen wipers, etc.) Ensure you are using 20A fuses for the HID lights. 10
11 IT IS IMPORTANT TO PLEASE READ THIS SECTION BEFORE USING THE HID LIGHTS F. Warnings and Correct Usage Information 1. Do not disassemble or modify the ballasts or wire harnesses. This product produces high pressure electricity and tampering with these components may result in electric shock. We are not responsible for malfunction or hazardous conditions caused by tampering and modification with the system. 2. Be certain that all ballasts, bulbs, wires and sockets are installed securely to the car body before operation. 3. Do not touch the lights after use until they have cooled. The bulbs emit heat at high temperatures and can cause burns 4. Keep the system and its components away from paper, cloth and inflammables such as lacquer, thinner and solvents to prevent fires. 5. Be certain you have your lights turned on only while the engine is running. Having your lights on before starting the engine causes battery drainage and may cause problems starting your vehicle. 6. Avoid looking directly into the xenon light to prevent potential damage to your eyes. 7. Do not position the lights in an upward direction or at oncoming drivers eye level so as to ensure their safety and visibility. 8. For repairs or replacement of components consult a professional technician. Do not attempt them yourself. 9. In a vehicle accident, be sure to turn off the vehicle s power to prevent high voltage electric leakage from the damaged product components. The system produces high voltage electricity which might interact with electronic components. Therefore in the case of vehicles equipped with advanced electronic control like for example board computers it is strongly recommended to consult with a specialist before installation. The manufacturer will decline claims resulting from inappropriate installation or application. Kensun will not be responsible for damages to automobiles resulting from the use, misuse, or inability to use a Kensun product. YOUR HID LIGHTS ARE NOW READY TO GO! 11
12 APPENDIX 1 MODIFICATIONS NEEDED FOR SOME VEHICLES MODELS The following electronic systems installed in some vehicles can affect the correct running and performance of the HID lights. Please read the modifications recommended here and consult with a specialist. A. Vehicles with Daytime Running Lights Daytime running lights use the HIGH or LOW beam driven at a lower voltage to save power. If you want to retain this option you need to install a relay harness as described in section D for Bi Xenon kits. Please be aware that the HID system will come on with the DRL at full power since it is relay driven. This is fine, although it will limit the life of the HID bulbs as it adds hours of usage. HID systems cannot be dimmed and to attempt to do so by reducing voltage will cause added current draw to compensate for this. To Bypass Alternatively you can remove the fuse to disable the DRL saving hours of HID light use. B.Lamp out Sensing In some vehicles the Lamp out Sensing is achieved by supplying a low voltage current to sense if the headlight lamp has blown. This may cause the HID lights to flash on and off. Modification Kensun recommends installing either Resistors or Warning Cancellers to prevent this. Both of these items can be purchased separately from Kensun and their function is to provide a steady power voltage to the HID lights. To Bypass Alternatively you can have a specialist disable the Lamp out Sensing electronics in your vehicle. C. Security Systems If your headlights flash when the alarm is armed and disarmed, as long as you are not frequently using the alarm disarm mode, it is fine to use the HID system in this manner Note that frequent alarm activation shortens the life of the HID bulbs 12
13 APPENDIX 2 Trouble shooting My engine compartment has no room for the ballast 1. Remove bumper and mount within 2. Zip tie or use double sided tape to secure I turn on the lights and the headlight flashes erratically 1. Make certain the battery has a minimum of 12 volts 2. The voltage in your vehicle may be unsteady (you won t notice this except that the HID lights flash on and off periodically). Kensun recommends installing a Relay Harness to keep the voltage steady to the HID system. You can purchase a relay harness separately from Kensun and install as described in section D When driving, the lights vibrate on the road 1. Check to see if the bulb is securely attached in socket 2. Check the bulb to see if it is broken I turn on the light but H.I.D won t turn on 1. Check the fuse in fuse box (Please upgrade to a 20A fuse) 2. Check and secure all connections 3. Some vehicles have reversed polarity. Change the polarity of the ballast connector. Reverse the connector from + to - and from - to + I turn on the lights and only one headlight turns on 1. Check the connection of bulb/igniter/ballast 2. Check if the bulb is faulty (i.e. swapping the bulbs to test if it works on other side) With the lights on, one looks brighter than the other 1. Clean headlight lens 2. Check for damage of housing 3. Have lens cleaned professionally 13
14 The lights keep on flickering and making clicking noises 1. Check that the HID bulbs have been connected to the ballasts correctly and tightly 2. Check the condition of the battery, that it is not too old or has a low charge 3. Check if your car has daytime running lights and disable the DRL by removing the fuse or purchase and install a relay harness Ballasts make electric noise when first turned on 1. This is normal, the ballasts are absorbing power from the battery to start up HID will only work when the high beam is turned on 1. This situation mostly happens with kits that have three prong plug rather than just + and - (H4, H13, 9007 and 9004 kits). Make sure you have plugged those three wires correctly to their positions. This occurs particularly with the 9004 and 9007 kits and we have attached a separate appendix on how to wire the 3 pronged plug correctly, please refer to 9004 and 9007 wiring Issue Appendix 3 The HID bulbs change color when first turned on 1. This is normal; at the beginning the ballasts are storing the power from the battery of the vehicle. Since the power has not been stabilized yet the bulbs may have different colors or even flicker. However, as soon as the power is stabilized by the ballast the bulbs will become normal. The color or lighting effects of the bulbs aren t matching 1. The level of the two sides bulbs in the headlight housing aren t even. Ensure both are at the same height and angle. Refer to Aligning Your Headlights Appendix 4 2. For new bulbs the colors may vary for the first few hours after being turned on. The color will become normal after that 3. Inspect for damage in the headlight housing. You may need to replace the housing 4. The headlight housing is dirty. Clean the lens or have the lens cleaned professionally 14
15 APPENDIX WIRING ISSUE: High beam shines when Low beam on, or High beam isn t working or both The HID 9004 and 9007 Bulbs have the same product specifications, unlike Halogen bulbs where there is a difference in these two sizes. Therefore HID 9004 and 9007 kits are not manufactured separately. However the wiring is different and there can be issues with bulbs being wired as 9007 when your vehicle needs 9004 or vice versa. Incorrect wiring will not damage your bulbs or vehicle. You should install the bulbs the way they came out of the box and if your bulbs are not functioning then switch the wires around until it works correctly. Do not adjust the wiring if the bulbs are going correctly. Instructions on how to change the bulbs from 9004 to 9007 or 9007 to Hold the blue connector with the front facing you and the straight side up (As shown in the diagram) 2. You will see three pins in the connector. One to the right, one to the left and one to the center 3. It may be helpful to label the wires to prevent confusion. (i.e. by attaching masking tape to the wires labeled with A, B, and C) Please note the coloring of the wires can vary 4. You then need to take the pins out of the connector. You can do this easily by bending the pins slightly up and down and then pulling the wires back 5. Now re-insert the pins in the correct order. The order should be: The right wire stays on the right The left wire goes in the center The center wire goes on the left 6. Afterwards you should have kept the right wire in place and swapped the left and center wires. Then re-install the bulbs 15
16 APPENDIX 4 ALIGNING YOUR HEADLIGHTS This is only a guide how to adjust the alignment of your headlights. We recommend you see a specialist for the best alignment for your HID headlights 1. Park your car on a level surface 20 feet behind another vehicle 2. Remove the trim around the headlights and locate the adjusting screws. These screws are typically found adjacent to the headlight 3. There should be one screw at the top of the headlight to adjust vertically and another screw to one side of the headlight to adjust horizontally. In some cars there may be adjusting bolts rather than screws 4. Turn on your headlights 5. Use a screw driver or socket to adjust the screws or bolts. Turn the upper screw or bolt clockwise to raise the headlight, and counterclockwise to lower it. Turn the side screws or bolts to move the headlight right or left 6. Adjust the headlight so the cut off of the beam is just above the bumper of the car in front (as in picture) 7. Be certain that the headlights are aligned evenly, point the lights at a flat wall at a distance of 20 feet and adjust until the beams are level 16
17 17
Xenon HID Lighting System
Automotive Safety Systems User Installation Manual Preface Specifications Thank you for purchasing NOVABLUE Xenon H.I.D. (High Intensity Discharge) vehicle lighting systems. Before installing this product,
More information2. Remove rear cover of head lamp if bulbs are covered/sealed within the housings, and remove halogen bulb carefully.
These instructions are designed to address most general installation procedures across vehicles and should not be considered vehicle make, model or year specific. Please contact the vendor directly for
More informationInstallation Instructions
520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
More informationDo not touch glass part of the bulb with your hands during installation.
HID Xenon Headbeam Lights Installation guide High quality! Do not touch glass part of the bulb with your hands during installation. When installing HID Xenon lights, place the ballast in a drafty area
More informationHID H4 BI-XENON FITTING GUIDE. Carefully read the following notes before starting work.
HID H4 BI-XENON FITTING GUIDE Carefully read the following notes before starting work. WARNING! This HID kit should only be installed by someone competent in vehicle wiring and electrics. Incorrect fitment
More informationWire(s) Won t Fit (Kit s Wiring Harness)
HID Conversion Kit General Troubleshooting Table of Contents 1. Bulb(s) Won t Fit 2. Wire(s) Won t Fit (For Kit s Wiring Harness) 3. One Side Consistently Doesn t Light Up 4. Both Sides Consistently Don
More information1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1 of 5 10/26/2007 4:48 PM 1999.5-2001 Audi A4 (B5) HID conversion installation instructions Tools Needed: A drill 1" hole saw T27 Torx bit and driver with a 4" extension Extendable magnet Pliers or A drill
More informationProjector90 Xenon Headlight Installation Guide
Projector90 Xenon Headlight Installation Guide Written exclusively for Umnitza s Projector90 Product This step-by-step guide is designed to be used in together with other available documentation including
More information12-Volt Negative Ground Installation Instructions
12-Volt Negative Ground Installation Instructions For Part Number: 1141, 1164, 1165, 1181 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for
More informationBILLET HEADLAMP WITH SHORT/TALL MOUNTS
-J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.
More informationFor customers Please forward this manual to the next owner.
PKI-0047 Installation Manual for LED Performance Bulbs (Type H8/H9/H11/H16) Thank you very much for purchasing PIAA product. Read this instruction manual thoroughly for proper use of the product. After
More informationBulb Replacement REPLACING BULBS WARNING
Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationPortable Air Conditioner
Portable Air Conditioner Owner's Manual Model:3 in 1 12,000 Btu/h Series 3 Please read this owner s manual carefully before operation and retain it for future reference. CONTENTS 1. SUMMARY...1 2. PORTABLE
More informationELECTRONICS G H I J K L M
ELECTRONICS TM LASER INSTALLATION INSTRUCTIONS PARTS KIT Parts Kit includes the following: A- (1) Universal Mounting Bracket A B- (1) Red L.E.D. Laser Alert Light C- (1) Piezo Beeper w/ O Ring Tape D-
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION:
Revision Level: 01 Revision Date: 07/07/2011 Please read all instructions carefully to help ensure a correct and SAFE installation of your Second Wind Ultraviolet Germicidal Air Purifier. Failure to do
More informationInstaller s Guide WARNING: 18-GJ11D1-2. Ultraviolet (UV-C) Lamp Kit for 2-5 Ton Air Handlers HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
Installer s Guide 18-GJ11D1-2 : Models: BAYUVCLK001-40 Watt, 2 Lamp NOTE: A BAYCC24VK01 can be installed for Series 8 Air Handlers to extend the life of the lamp. This accessory kit will disable the lamp
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More information1R / 4-BUTTON SERIES
Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationNot required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)
ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationGet your lights right. What you need to know about fitting and using additional vehicle lighting
Get your lights right What you need to know about fitting and using additional vehicle lighting NZ Transport Agency Get your lights right 2012 NZ Transport Agency 1 GET YOUR LIGHTS RIGHT CONTENTS WHAT
More information1000-LB. TRAILER JACK OWNER S MANUAL
1000-LB. TRAILER JACK OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationINSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS
3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More informationHow To: Retrofit the Morimoto Mini D2S bi-xenon Projectors
How To: Retrofit the Morimoto Mini D2S bi-xenon Projectors Warning: By reading this document I agree that it is only intended to be used as an educational guide. The Retrofit Source Inc. makes no guarantee
More informationINFRARED QUARTZ WALL HEATER
INFRARED QUARTZ WALL HEATER MODEL NO: IQ2000 PART NO: 6939004 MOUNTING & OPERATION INSTRUCTIONS GC0715 INTRODUCTION Thank you for purchasing this CLARKE Infrared Wall Heater. Before attempting to use this
More informationNational Optical & Scientific Instruments Inc. 11113 Landmark 35 Drive San Antonio, Texas 78233 Phone (210) 590-9010 Fax (210) 590-1104
National Optical & Scientific Instruments Inc. 11113 Landmark 35 Drive San Antonio, Texas 78233 Phone (210) 590-9010 Fax (210) 590-1104 INSTRUCTIONS FOR MODELS 106, 106-L 107, 107-L 108, 108-L 109-L ELEMENTARY
More information3 WATT LED SPOTLIGHT Model No. SLM - 3801
3 WATT LED SPOTLIGHT Model No. SLM - 3801 OWNER'S MANUAL Customer Service Tel: 1-800-268-3319 Superex Canada Ltd, Toronto,M2H 3B8 Made in China Table of Contents A). Important Safety Instructions B). Charging
More informationCeiling Fan Installation Instructions
Ceiling Fan Installation Instructions 1525..series OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS Total fan wieght with light kit 1-1525-CUL-English INSTALLATION CH-545 Safety Tips WARNING: TO REDUCE
More information5W LED Energy Saver PIR Bulkhead
5W LED Energy Saver PIR Bulkhead Model: LED88PIR Black I n s t a l l a t i o n & Ope r a t i n g I n s t r u c t i o n s 1. General information: The unit utilises passive infrared technology to detect
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationMODELS 8007 Gorilla Cycle Alarm 8017 Gorilla Cycle Alarm with 2-way pager system 1018 2-way pager system
MODELS 8007 Gorilla Cycle Alarm 8017 Gorilla Cycle Alarm with 2-way pager system 1018 2-way pager system Remote Control Motorcycle Alarm System Installation & Operation Instructions Sistema de Alarma de
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Vacuum Pump Kit 28146 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully follow these instructions
More informationOwners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family
Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Part of the Kiva Lighting Family Custom Lighting and Fans Since 1992 1312 12th St NW Albuquerque,
More informationMODELS 7007 Gorilla Cycle Alarm 7017 Gorilla Cycle Alarm with 2-way pager system 1017 2-way pager system
MODELS 7007 Gorilla Cycle Alarm 7017 Gorilla Cycle Alarm with 2-way pager system 1017 2-way pager system Remote Control Motorcycle Alarm System Installation & Operation Instructions Sistema de Alarma de
More informationOwner s Guide and Installation Manual. Vancouver Model Name. 21321, 21328 Model No. English Español
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Vancouver Model Name 21321, 21328 Model No. Type A Models Owner s Guide and Installation
More informationi ChatterBox! Motorcycle Security
i Before you Start the Installation * Please read this manual to become familiar with the requirements necessary to complete the installation. * Use a high quality multi-meter to test all wires before
More informationSECURITY LIGHT. motion-activated. Assembly & operating instructions Solar Motion-Activated Security Light - 80 LED Lights
motion-activated SECURITY LIGHT Model #: 40225, 40226 Assembly & operating instructions Solar Motion-Activated Security Light - 80 LED Lights Important: Read all instructions carefully before use About
More informationBULB REPLACEMENT BROCHURE
BULB REPLACEMENT BROCHURE Contents Contents Explanation of Symbols 03 Audi A1 04 06 Audi A4 1.9 TDI with Xenon Headlights (from years of manufacture 2000 to 2005) 07 10 Audi A4 (8K5 / 8K2) with Bi-Xenon
More informationInstallation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT!
Installation Instructions Avalanche XUV Cap IMPORTANT! Read all instructions carefully before commencing any work. Always wear safety equipment. Some installation steps will require two or more installers.
More informationJuice Box Stages 1&2 135&335 Installation Guide 5/10/08
Tools Required: 8mm socket or nut driver Small flat head screwdriver Electrical tape, masking tape, or shrink tube Pep talk: Although the install looks daunting at first, once you get the learning curve
More informationEZ-Steer Assisted Steering System
EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT
More informationUSER INSTRUCTIONS FOR GET PORTABLE 12k BTU AIR CONDITIONER MODEL No. GPACU12HR
USER INSTRUCTIONS FOR GET PORTABLE 12k BTU AIR CONDITIONER MODEL No. GPACU12HR CONTENTS Introduction Safety Notes Identification of parts Installation instructions Operation instructions Maintenance Troubleshooting
More informationSP AF 300mm F/2.8 LD [IF] for Canon (Model 360EE)
SP AF 300mm F/2.8 LD [IF] for Canon (Model 360EE) We greatly appreciate your purchase of this Tamron lens. The Tamron SP AF 300mm F/2.8 LD [IF] is a fast telephoto lens developed for Canon AF single-reflex
More informationIMPORTANT INSTRUCTIONS & OPERATING MANUAL. Houston 50 Inch Electric Wall Mounted Fireplace Black / White
IMPORTANT INSTRUCTIONS & OPERATING MANUAL Houston 50 Inch Electric Wall Mounted Fireplace Black / White Model Number:MFE5050BK Model Number:MFE5050WH Read these instructions carefully before attempting
More informationM-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information1. SAFETY RULES. 8. Avoid placing objects in the path of the blades.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More information1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationNetworkfleet 3500 Product Line Installation Guide
Networkfleet 3500 Product Line Installation Guide Light/Medium Duty (L3500) Heavy Duty (H3500) Universal (U3500) www.networkcar.com/fleet Customer Care: (866) 227-7323 customercare@networkcar.com Table
More informationUSER MANUAL WARNING! CONTENTS MODEL 1 SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING. Non-Programmable Single Stage Heat/Cool Thermostat
Builder MODEL 1010 Series Non-Programmable Single Stage Heat/Cool Thermostat USER MANUAL Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single stage
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationEVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board.
EVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board. This Troubleshooting Guide covers the electric coolant valve and control
More informationSTART 0:30 BEFORE YOU. Bi-Xenon Harness Installation Instructions
Bi-Xenon Harness Installation Instructions BEFORE YOU START Disclaimer: By reading this document, you agree that it is only intended to be used as an educational guide. Black Flame Customs, Inc. makes
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More informationArctic Leash Instruction Manual Alaskan Products Company LLC.
Retractable Cord Reel for Engine Block Heaters Arctic Leash Instruction Manual Alaskan Products Company LLC. INSTALLATION INSTRUCTIONS This instruction manual is a reference guide for installing and operating
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationMartin County Amateur Radio Association. Nightfire Kits 1 LED Torch Kit 270016. Contents. Description
Nightfire Kits 1 LED Torch Kit 270016 1 Contents Nightfire Kits LED Torch Kit 270016... 1 Description... 1 Safety and Assembly of the kit... 6 Required and Useful Tools... 7 Assembly... 8 Checkout and
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationModel: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features
Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Mirror with built in 4.0 LCD Monitor Low Profile, Slim Design High Resolution TFT LCD Built in Speaker Two video inputs Fully
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL HB6PAKX & HB6PAKXX HIDE-A-BLAST STANDARD HIDE A BLAST UNIT HB6PAK-PI-X NGPI TWIST LOCK HIDE-A-BLAST LED WARNING LIGHT NGPI TWIST LOCK HIDE A BLAST UNIT IMPORTANT: 6 LED
More informationHeat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board
Heat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board 2012 HS M4417A BR16597R-1 HEAT SURGE 8000 FREEDOM AVE, N. CANTON, OH 44720 330-244-8161 WWW.HEATSURGE.COM
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More information15GAL STEEL OIL DRAIN WITH 110V PUMP
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationMAINTENANCE & TROUBLESHOOTING
MAINTENANCE & TROUBLESHOOTING This section describes how to: clean the lens replace the projection lamp replace the batteries in the remote use the security lock feature troubleshoot the projector Cleaning
More informationSolar Home System. User Manual. AEH-SHS01-10W2L Solar Home System 2 Lamps
Solar Home System User Manual AEHSHS0110W2L Solar Home System 2 Lamps All rights reserved Specifications subject to change without prior notice 2 Dear Customer, Thank you for purchasing Schneider Electric
More informationR02GA. July 31, 2002. Dear Blue Bird Owner:
R02GA July 31, 2002 Dear Blue Bird Owner: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Blue Bird Body Company has determined that
More informationAuto-belay Cable Replacement Process
Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable
More informationPet hair clipper. Model 96822. Diagrams within this manual may not be drawn proportionally.
Pet hair clipper Model 96822 Cleaning And Operation Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the
More informationM A R C O. CP-670 AUTOMATIC CHART PROJECTOR Instruction Manual
M A R C O CP-670 AUTOMATIC CHART PROJECTOR Instruction Manual CONTENTS GENERAL DESCRIPTION............... 1 INSTALLATION...................... 2 Mounting the Projector Positioning the Projector Positioning
More information60 WATT LED TRIPLE BEAM WORKLIGHT
60 WATT LED TRIPLE BEAM WORKLIGHT OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationMAINTENANCE & TROUBLESHOOTING
MAINTENANCE & TROUBLESHOOTING This section describes how to: clean the lens clean the fan intake filter replace the projection lamp replace the batteries in the remote control use the Kensington lock feature
More information1. SAFETY RULES WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT".
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationGreenWay Solar LED Path and Trail Lighting System. Installation and Owner s Manual
GreenWay Solar LED Path and Trail Lighting System Installation and Owner s Manual Important Notes and Warnings This installation and instruction manual provides installation, operation, and maintenance
More informationOperations Manual SledStart H4 HID Light Kit
Operations Manual SledStart H4 HID Light Kit ` Table of Contents INTRODUCTION...1 SAFETY WARNING...1 PACKAGE CONTENTS...1 INSTALLATION INSTRUCTIONS...2 NOTES... 7 Copyright 2010 SledStart LLC All Rights
More informationATS Overhead Table Shelf System INSTRUCTION MANUAL
ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship
More informationOperating Instructions
Operating Instructions Series L 4000 Spring Driven Cord Reels 63 3 3 3 7A 63 0 63 3 3-RP 3 7B 63 X 6 3 3A 63 8 3 X 6 3 3A-RP 63 8 L 4000 63 3 3 3B 63 9 L 400 63 3-RP A 63 5 3 9 L 4500 63 3 A 63 5 3 9G
More informationINSTALLATION & OPERATION MANUAL LED
INSTALLATION & OPERATION MANUAL LED Duo Beam TM Introduction... 2 Lightbar Unpacking & Pre-Installation... 2 Installation & Mounting... 3 Wiring Instructions... 4 Maintenance... 4 Flash Pattern Selection...
More information19 LED Tube Controller ORDERCODE 41003
19 LED Tube Controller ORDERCODE 41003 Congratulations! You have bought a great, innovative product from Showtec. The Showtec 19 LED Tube Controller brings excitement to any venue. Whether you want simple
More information`ÉàÉÜvçvÄxÅxàtÄAvÉÅ \ÇvA 5490 S.W. 42nd St. Davie, FL 33314 1-866-899-5962 Toll free 1-954-449-6173 Local
`ÉàÉÜvçvÄxÅxàtÄAvÉÅ \ÇvA 5490 S.W. 42nd St. Davie, FL 33314 1-866-899-5962 Toll free 1-954-449-6173 Local About: HID Lamp Systems Will I Lose The Ability To Use The High Beams: No! I only sell HID components
More informationCMD-10k COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM
CMD-10k COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM INTRODUCTION Thank you for purchasing the CMD-10k Commander from Dakota Digital. This, along with many other products that Dakota Digital has to offer,
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationBullet Camera. Installation Guide. Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.com
Bullet Camera Installation Guide Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.com 1 Thank you for purchasing our product. If there are any questions, or requests, please do not
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationLeft Hand Limit Switch. Housing. Left Hand. Connections. Motor Connector BROWN PURPLE GRAY BLACK DARK BLUE BLACK BROWN BROWN LIGHT BLUE.
LIGHT BLUE GRAY PURPLE Circuit Breaker Intput Circuit Breaker Output #1 Relay Left Hand Limit Switch Housing Left Hand Motor Connector Right Hand Limit Switch on Radiator Support Right Hand Limit Switch
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationYour safety and the safety of others are very important.
NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...
More informationIH 17025 E Sigma Island 90
INSTRUCTIONS FOR USE Kitchen extractor hood Type: IH 17025 E Sigma Island 90 Dear Customer!! You are now a user of the newest generation kitchen extractor hood type IH 17025 E Sigma Island 90. This hood
More informationRemote Access System Installation
2011-2013 Explorer Remote Access Remote Access System Installation CONTENTS VEHICLE PREPARATION Hood Switch Wire Harness Installation Hood Switch Installation RMST Module Installation RMU Module Installation
More informationOdyssey of the Mind Technology Fair. Simple Electronics
Simple Electronics 1. Terms volts, amps, ohms, watts, positive, negative, AC, DC 2. Matching voltages a. Series vs. parallel 3. Battery capacity 4. Simple electronic circuit light bulb 5. Chose the right
More information