1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide
|
|
- Bartholomew Johnston
- 7 years ago
- Views:
Transcription
1 1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2 LED extension harnesses, 12 1 harness crimp kit 8 mounting brackets PN Please efer r to webiste for full warranty information. DIGI-TAILS is not a licensed Mopar product.
2 1969 DODGE CORONET LED PANEL INSTALLATION 2 The LED boards are shipped with the slide switch set to sequential mode. We recommend that all slide switches be set to the same setting (either standard or sequential). SEQUENTIAL POSITION STANDARD POSITION Please follow all local laws concerning exterior lighting. Shown in sequential mode Hint You may begin with the LED panel installation, however, you will need to complete the wiring modifications before the LED panels and housings are paired as one. Read over the entire instruction guide to determine the method that works best for you. LED PANEL INSTALLATION 1. Cut off the power to your car. Open the hood of your car. Disconnect the negative terminal from the battery, which will cut off the power in your car. To verify that the power is disconnected, press the brake pedal; your brake lights should not turn on. 2. Remove the current taillights. Turn the light sockets counter-clockwise to remove them from the taillight housings. As a safety precaution, remove the bulbs from the sockets. Put them aside since they will no longer be needed. Remove the taillight housing assembly from rhe car. 3. Position the LED panels. Each LED panel is marked Driver Side and Passenger Side on the backside of the LED panel, which identifies where each respective LED panel is to be mounted. The Driver Side LED panel is shown above.
3 1969 DODGE CORONET LED PANEL INSTALLATION 3 4. Attach mounting brackets. Each light pocket on the taillight housing needs to be marked for placement of the right angle brackets. To do this, first have the housing right side up, Then from the edge of the housing measure back 1/4 and mark a parallel line. Now flip the housing upside down. Then from the edge of the housing measure 3/8 and mark a parallel line. The face of all brackets should be flush to these lines. Remove the protective tape and carefully position each bracket into place. Each housing uses four brackets. The LOWER brackets are to be marked 1/4 from the edge The UPPER brackets are to be marked 3/8 from the ledge. Housing right side up, measure 1/4 from edge for the LOWER brackets. Flip the housing around, and measure 3/8 from edge for the UPPER brackets. 5. Plug in extension harnesses. Feed the extension harness through the socket hole and plug them onto the LED panels. Using these extension harnesses allows for easy removal of the tail light assembly in the future if needed.
4 1969 DODGE CORONET LED PANEL INSTALLATION 4 6. Mount the LED panels. Test fit the LED panels into place before they are permanently attached to the brackets. Be certain that the LED panels are parallel with the housing edge then peel off the remaining protective tape and affix the LED panels. The correct orientation for the LED panel is to have the arrows on the LED panel pointing towards the outside, opposite of the reverse light socket.
5 1969 DODGE CORONET WIRE SPLICING INSTALLATION 5 WIRE SPLICING INSTALLATION 1. Review the wiring diagrams found on the last page. Each LED panel needs five connections. Listed are the LED harness colors and their respective function. : Depending on make and harness, colors may not match. ORANGE BLACK YELLOW GREEN BROWN - Constant 12 volt power source. - Grounded to body. - Running/parking light signal. - Driver side turn signal. - Passenger side turn signal. 2. Find and access the taillight wires. Pick a point in the rear body panel between the driver s side quarter panel and the driver s side taillight housing assembly and remove the cloth tape to expose the taillight wires. 3. Splice the LED SIGNAL wires into the stock SIGNAL wires. Match the LED harness to the corresponding stock harness as shown below. LED Harness Function Stock harness s Brown Passenger side turn signal Brown The light socket ends on the car harness can be removed. Green Driver side turn signal Green The light socket ends on the car harness can be removed. Yellow Running/Park signal Black Running light wires. THIS IS NOT THE CAR S GROUND. Orange Black Constant 12 volt Ground Find power at fuse panel/trunk light/dome light/fused battery feed. Ground to Body/chassis 4. Connect all the ground wires. Connect all the ground wires together. Bolt them to the trunk latch support along with the original rear body harness ground. The ground connection must be good in order to the operate the LED tail lights.
6 supplied with a constant 12 volt battery supply for the LED circuitry to ope the T-Tap. The other end of the orange wire is splice Take the LED harness YELLOW wires and splice them in with the original BLACK running Take the The LED T-Tap harness connector BROWN wires and light wires. is used splice it The ends to with going splice the original BROWN wires. to the to side the marker constant lights must power be included source, in the like splice the for The last page is a wire diagram of how the LED harn the side markers to remain functional. The light socket ends on the car harness are no longer needed DODGE CORONET WIRE SPLICING INSTALLATION 6 Spice the T-Tap connector into the constant power wire, then plug the oran the T-Tap. The other end of the orange wire is spliced into the LED harness Take the ground wires and connect them all together. Bolt them to the trunk latch Take the LED harness YELLOW wires and splice them in with the original BLACK running 5. Supply the LED panel harnesses with a constant support along 12 volt with the original rear body harness ground. 1. Insert wire light wires. The ends going to the side marker lights must be included in the splice for feed using the included the side Orange markers power to remain wire functional. and T-Tap. : A good ground connection is essential to the operation of the LED tail lights. The last page is a wire diagram of how the LED harness splices into the car s Take the ground wires and connect An ORANGE them power all together. wire is Bolt supplied them along to the with trunk a T-Tap. latch The orange power wire must be An Orange power wire support is supplied along with along the with original supplied a T-Tap. rear body with The harness a constant ground. 12 Insert volt battery wire supply onto T-Tap for the LED circuitry Crimp to operate with properly. pliers orange power wire must powered with a constant The T-Tap 12 connector volt is used to splice to the constant power source, like the dome light w : A good ground connection is essential to the operation of the LED tail lights. 2. Crimp with battery supply for the LED circuitry to operate properly. You Spice the T-Tap connector into the constant To power keep wire, the wires then pliers plug neatly the orange tucked wire and into in l can use the included An T-Tap ORANGE connector power wire to is splice supplied along with a T-Tap. The orange power wire must be the T-Tap. to a constant The other end of the orange wire them is spliced over into one the LED side harness and tape Orange them wires. in power source, like the supplied dome with light, a constant trunk light, 12 volt fuse battery box, supply etc. for the LED circuitry to operate properly. The T-Tap connector is used to splice to the constant power source, like wiring the dome into light loom wire. or have the ability to w The last page is a wire diagram of how the LED harness splices into the car s original harn Spice the T-Tap connector Spice the over T-Tap the connector constant into power the constant source, power wire, then plug the orange wire into Plug then plug the orange the wire T-Tap. into Insert The the other T-Tap. wire end of onto The the other orange T-Tapend wire is ofspliced into the Crimp LED harness with Orange plierswires. the orange power wire is tied in with the orange wires of The last page is a wire diagram of how the LED harness splices Wires into spliced the car s together. 3. Plug original harness. Fold connector wires over to a side. all the LED panel harnesses. To keep the wires neatly tucked and in line, take the Plug spliced connector Insert wire onto T-Tap Crimp with pliers! sec them over to one side and tape them in place. This will allow y wiring into loom or have the ability to wrap the LED harness w To keep the wires neatly tucked and in line, take the spliced sections and fold them over to one side and tape them in place. This will allow you to place th Plug connector 6. Tuck and secure the spliced Insert wire onto wires. T-Tap Crimp with pliers 1. Fold wires to Take the spliced sections and To fold keep them wires over neatly to one tucked side and in line, take the spliced sections and fold one side. and tape them in place. This will them allow over to you one side Wires place and tape spliced the them in place. This will allow you to place the Wires wiring spliced into loom together. or have the ability together. to Fold wrap the wires Fold LED wires harness over to wiring a side. tightly away. Wrap with Wrap tape with to hold tape in placet wiring into loom or wrap the LED panel wiring tightly away.! 2. Secure with! electrical tape. Wires spliced together. Fold wires over to a side. Wrap with tape to hold in place.! A wire diagram of the LED panel s harness spliced into the car s stock harness is on the last page. 7. Place the grommet around the wires and replace the lens. Place the grommet around the panel wires and press it into the light socket hole. Test the lights to ensure correct function, then place the lens back onto the housing. The LED light kits are designed for best performance when use an electronic no-load flasher. Shown here is an optional electronic no load flasher available from DIGI-TAILS, ( PN 20-F2 ) If you decide to use a stock bi-metal flasher, we recommend a standard-duty flasher instead of a heavy-duty flasher. If your turn signal circuit includes front and rear LED turn signals, the circuit will not have enough resistance load to operate a heavy-duty bi-metal flasher, so the no-load flasher will be required for both the turn signal and emergency flashers.
7 1969 DODGE CORONET WIRE SPLICING INSTALLATION 7 STOCK HARNESS COLORS. BROWN: GREEN: BLACK STOCK REAR BODY HARNESS PASSENGER SIDE TURN SIGNAL DRIVER SIDE TURN SIGNAL RUNNING LIGHTS ALTHOUGH CLOSED END CONNECTORS ARE INCLUDED, IT IS RECOMMENDED THAT ALL SPLICED WIRES BE SOLDERED TOGETHER FOR BEST CONNECTION RELIABILITY. POWER CONNECTION CONSTANT FUSED POWER SOURCE. (AT DOME LIGHT OR FUSE PANEL) DRAWS LOW CURRENT, LESS THAN 3 AMPS. BOTH LED PANELS REQUIRE THE DRIVER AND PASSENGER SIDE SIGNALS. GROUND WIRES DRIVER SIDE LED PANEL PASSENGER SIDE LED PANEL
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Vacuum Pump Kit 28146 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully follow these instructions
More informationELECTRONICS G H I J K L M
ELECTRONICS TM LASER INSTALLATION INSTRUCTIONS PARTS KIT Parts Kit includes the following: A- (1) Universal Mounting Bracket A B- (1) Red L.E.D. Laser Alert Light C- (1) Piezo Beeper w/ O Ring Tape D-
More informationCoolWave r 2 Phase Control Board and Cable Replacement Kits
Instruction Sheet P/N 1102452A CoolWave r 2 Phase Control Board and Cable Replacement Kits Two kits are available to replace the CoolWave 2 phase control board: S S Phase Control Board and Cable Kit (required
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationInstallation Instructions: Electrical System for Towing Hitch... 3
... 3 Installation Instructions: Electrical System for Towing Hitch... 3 321 527 391 103-002 - 51/12 VW Polo A05 RHD Westfalia 321 525 300 143 VW Polo V RHD, 06/09-321 527 300 143 VW Polo V RHD, 06/09-4
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationby Myles H. Kitchen M.H. KITCHEN & ASSOCIATES www.auto-electronic.com (2002 X5 4.4 owner) March 2, 2004
INSTALLING THE TEKONSHA PRODIGY ELECTRIC TRAILER BRAKE CONTROL IN THE BMW X5 by Myles H. Kitchen M.H. KITCHEN & ASSOCIATES www.auto-electronic.com (2002 X5 4.4 owner) March 2, 2004 INTRODUCTION The 2000
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationModel: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features
Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Mirror with built in 4.0 LCD Monitor Low Profile, Slim Design High Resolution TFT LCD Built in Speaker Two video inputs Fully
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE KEYLESS ENTRY MODELS KE100 / KE150 / 1702 CONTENTS System Features... 1 System Components... 1 Technical Assistance... 1 Before You Begin... 1 Precautions... 1-2 Making
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More information2. Remove rear cover of head lamp if bulbs are covered/sealed within the housings, and remove halogen bulb carefully.
These instructions are designed to address most general installation procedures across vehicles and should not be considered vehicle make, model or year specific. Please contact the vendor directly for
More informationPARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS
Form 1-696 R1 January, 2003 PARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS PARTS LIST ITEM PART NO. QTY. DESCRIPTION 07033 1 SNOW PLOW LIGHT CARTON 1 07034 1 Snow Plow Light, Pass. Side (No Hardware)
More informationPUSH BUTTON START INSTALLATION MANUAL
PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More information1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
More informationBack-Up Camera Installation Guide
Hz Hz In This Guide: Back-up camera installation requires connecting power wiring to the existing reverse lighting circuit and adding a chassis ground, as well as routing a video signal cable to the front
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationJuice Box Stages 1&2 135&335 Installation Guide 5/10/08
Tools Required: 8mm socket or nut driver Small flat head screwdriver Electrical tape, masking tape, or shrink tube Pep talk: Although the install looks daunting at first, once you get the learning curve
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More informationVehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions
Model PRO 9842 Installation Manual Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical
More informationSpreader Light Bulb Replacement Instructions
Spreader Light Bulb Replacement Instructions IMPORTANT: DISCONNECT LIGHT FROM BATTERY BEFORE PROCEEDING. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR OTHER DAMAGE. Tools Needed You will need the following
More informationI Click on a link tab to jump to that page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationI Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationPower Door Locks Cruise Control System. Cigarette Lighter. Blower. Fan. Windshield Wiper System. See Note. High Wiper. Med. Low.
+ + Power Door Locks Cruise Control System Cigarette Lighter Power Windows Blower Fan Windshield Wiper System Clock Radio Rev. Light Switch See Note HVAC Side Marker Light Park/Turn Signal Low/High Beam
More informationHID H4 BI-XENON FITTING GUIDE. Carefully read the following notes before starting work.
HID H4 BI-XENON FITTING GUIDE Carefully read the following notes before starting work. WARNING! This HID kit should only be installed by someone competent in vehicle wiring and electrics. Incorrect fitment
More informationI Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationWireless Reverse Parking Camera
Wireless Reverse Parking Camera RAC-HP102 This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to
More information1970-72 Chevelle. 1970-72 Chevelle. (500645) Gauge Cluster Kit Installation Instructions. (500645) Gauge Cluster Kit Installation Instructions
1970-72 Chevelle (500645) Gauge Cluster Kit Installation Instructions 1970-72 Chevelle (500645) Gauge Cluster Kit Installation Instructions STEP 1: There are 4 small gauges. This is a photo of the bare
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More information20000068 WIRELESS REMOTE ASSEMBLY, 24VDC, 1 TRANS,1 REC
20000068 WIRELESS REMOTE ASSEMBLY, 24VDC, 1 TRANS,1 REC Fitment to MP-25 620 CR 4841, Haslet, TX 76052 Ph 817.439.1108 Fax 817.636.5675 www.machine-technologies.com Kit contents 1 Transmitter 2 button,
More informationINSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR
INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing
More informationInstallation of Rear View Camera in a 1995 Roadtrek 190 Popular
Installation Instructions: 1995 Roadtrek Rear View Camera Page 1 Installation of Rear View Camera in a 1995 Roadtrek 190 Popular Introduction. In the fall of 2010 we investigated rear view cameras for
More informationINSTALLATION INSTRUCTIONS: Viewline 52 mm
-5 Safety information The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of-the-art technology. The instrument is designed for use
More informationWalbro 255lph Inline Fuel Pump Install Procedure
Walbro 255lph Inline Fuel Pump Install Procedure Note: Instructions are based on a single in tank pump with under car OEM VW filter. Total install time for a qualified technician is approximately 2 hrs.
More informationi ChatterBox! Motorcycle Security
i Before you Start the Installation * Please read this manual to become familiar with the requirements necessary to complete the installation. * Use a high quality multi-meter to test all wires before
More informationINSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS
3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More information- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory
Door Wiring Harness Plug Connections Binder -, Electrics Vehicle Type: (86) Model Year: 7 (V) Concern: Door wiring harness plug connections X11 / X12. Information: The rubber boot for the door connector
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationUse subject to terms and conditions posted at http://www.burgertuning.com/terms.htm
Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS NOT LEGAL FOR
More informationCompanion Service Guide
Companion Service Guide This Service Guide contains: Troubleshooting Replacement Instructions Contact Information Golden Technologies 401 Bridge Street Old Forge, PA 18518 Toll-free: 800-624-6374 Fax:
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationOriginal BMW Accessories. Installation Instructions.
Original BMW Accessories. Installation Instructions. Rear view camera retrofit BMW X5 (E70) These installation instructions are only valid for cars with: SA 508 (PDC) with SA 601 (TV function) SA 508 (PDC)
More informationCMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM
INTRODUCTION CMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM Thank you for purchasing the CMD-8000 Commander from Dakota Digital. This, along with many other products that Dakota Digital has
More informationInstructions for: TTW 1 Universal Service Replacement Blower Kit P/N 265-47200-00
Instructions for: TTW 1 Universal Service Kit P/N 265-47200-00 (To be performed ONLY by qualified service providers) The Blowers on the Following Water Heaters are Serviced by This Kit: MITW -10 Series
More informationPower Window/Power Lock Installation. To begin with you will need all the parts listed below:
Power Window/Power Lock Installation To begin with you will need all the parts listed below: From Donor Fiero: Fiero power window regulators Power window motors (Generic GM type part) -motors are riveted
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationR02GA. July 31, 2002. Dear Blue Bird Owner:
R02GA July 31, 2002 Dear Blue Bird Owner: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Blue Bird Body Company has determined that
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More information510351 92970196 instruction rev 0.0 11/13/2012
INSTRUMENT LUSTER ISNET AESSORY NETOR INITION Sheet 2 FLOOR IMMER WIPER PA AS ROUN LEFT AN RIT AN ELETRI SPEEO ROUN ORN RELAY TURN SINAL PARIN BRAE NEUTRAL SAFETY EALIT BRAE RAIO IARETTE LITER BA UP INSTALLIN
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationInstallation instructions, accessories. Cruise control. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30739998 1.
Instruction No Version Part. No. 30739998 1.1 Cruise control Page 1 / 11 Equipment A0000162 A0000161 A0801178 D8802049 Page 2 / 11 M8802108 Page 3 / 11 IMG-223164 Page 4 / 11 IMG-213320 Page 5 / 11 INTRODUCTION
More informationChevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G
INSTALLATION INSTRUCTIONS FOR PART 99-3307G Chevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationLED NarrowStik LED LC-Stik
INSTALLATION & OPERATION MANUAL NASL547/39 NASL847/39 NAS3547/39 NAS3847/39 NarrowStik LCC547/39 LC847/39 LC-Stik LC-STIK NARROWSTIK 3-Up OPTIX TM NARROWSTIK LED NarrowStik LED LC-Stik Contents: Introduction
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationSpurious diagnostic trouble codes in the airbag system (SRS)
SERVICE INSTRUCTION Number: 850-2077 Year: 1999 Month: Market: FEBRUARY ALL Spurious diagnostic trouble codes in the airbag system (SRS) Cars affected Saab 9-5 4D M98-99 up to and including chassis number
More informationBACKUP CAMERA JEEP COMMANDER/GRAND CHEROKEE
BACKUP CAMERA 1 JEEP COMMANDER/GRAND CHEROKEE 2 Call Out Description Parts Quantity 1 Tie Wrap-Nylon 6.9" Supplied in kit 12 2 Camera, Rear View Supplied in kit 1 3 Camera Extension Harness Connector Supplied
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationINSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationOwner s Manual Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles P/N ASM5075
Owner s Manual Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles P/N ASM5075 Thunder Heart Performance Corporation MANUAL P/N EI5075 120 Industrial Drive Revision 7/15/05 White
More informationINSTALLATION INSTRUCTIONS: Viewline 85 mm
1-10 1 Safety information The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of-the-art technology. The unit is designed for use
More informationInstallation Instructions: Electrical System for Towing Hitch...3
Fehler! Textmarke nicht definiert....3 Installation Instructions:...3 317 056 391 104-002 - 22/07 Westfalia Skoda 317 056 300 153 Skoda Octavia II (1Z), 4x4, RS, RHD 3 2 1 1 2 3 4 5 6 7 2 317 056 391 104-002
More informationBoxster. Technical Information. Service 3/99 9415. Litronic Retrofit Kit
Litronic Retrofit Kit 9 3/99 9415 Binder - 9, Electrics This bulletin replaces bulletin Grp. 9, #3/99, dated 5-20-99. Vehicle Type: Model Year: Concern: Information: As of 1997 (V) Retrofitting Litronic
More informationEXTENDED-WIRE HANDLEBAR SWITCH KITS
-J03396 REV. 2010-02-11 EXTENDED-WIRE HANDLEBAR SWITCH KITS ENERAL Kit Numbers 70246-10, 70318-10 Models Neither of these kits is compatible with cruise control-equipped 2007 or earlier models. Kit 70246-10
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationInstallation Instructions
520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
More informationTwo signal flashers and two pre-wired relay connectors for horn relay and fan relay
INSTRUCTIONS 910-64017 Speedway Motors, inc. November 2009 12 Circuit Wiring Harness Please Read Instructions Completely Before Starting Your Installation This kit contains the following: One pre-wired
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More information1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1 of 5 10/26/2007 4:48 PM 1999.5-2001 Audi A4 (B5) HID conversion installation instructions Tools Needed: A drill 1" hole saw T27 Torx bit and driver with a 4" extension Extendable magnet Pliers or A drill
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012- PART NUMBER: 250-9628 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION
More informationRemote Access System Installation
2011-2013 Explorer Remote Access Remote Access System Installation CONTENTS VEHICLE PREPARATION Hood Switch Wire Harness Installation Hood Switch Installation RMST Module Installation RMU Module Installation
More informationILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L
An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair
More informationFor a simple splice connection look at figure 21. This basic type of splice can be used almost exclusively when hooking up your wiring.
Page 1 of 10 IMPORTANT: Before starting installation, please be sure that all items which were supplied with the kit are accounted for. Note: These instructions are to be used in conjunction with the instructions
More information1R / 4-BUTTON SERIES
Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote
More informationPart Name/Description Part Number Quantity. Power Cable 4000950-5 1
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions
More informationChanging the C6 Front DRL/Turn signal bulb DIY.
Changing the C6 Front DRL/Turn signal bulb DIY. The Corvette C6 DRL/Turn signal bulb will eventually need to be changed. With the DRL bulbs on most of the time the bulb gets hot and over several hundred
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationSCHWINTEK IN-WALL SLIDEOUT TROUBLESHOOTING AND COMPONENT REPLACEMENT
Troubleshooting Error Codes During operation when an error occurs, the board will use the LEDs to indicate where the problem exists. For motor specific faults, the green LED will blink once for Motor 1,
More informationPRO PLM Installation Instructions
PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More information