Room Air Conditioner: Remote Controller

Transcription

1 Owner s & Instruction Manual Room Air Conditioner: Remote Controller Heat Controller, Inc. 900 Wellworth Ave. Jackson, MI 490 (57)

2 Owner s Manual Room Air Remote Controller Heat Controller, Inc. CONTENTS Using Handling the the remote remote controller Remote controller Specifications... Function buttons How to use the buttons... Auto operation... Cooling/Heating/Health operation... Dehumidifying operation... Sleep operation... Timer operation

3 ESnaevregry TEMP/ TEMP/ CFhi letecrk FoM leow on off Auto Auto Cool High Mode Fan On/off Dry Med Timer Heat Fan Low Sleep Heat Controller, Inc. Room Air Remote Controller Owner s Manual Using Handling the the remote controller 5m Location of the remote controller. Use the remote controller within a a distance of 5 of meters 6 ft (5m) from from the appliance, the appliance, pointing pointing it towards it towards the receiver. the receiver. Reception Reception is confirmed is confirmed by a beep. by a beep when a button on the remote controller is pressed. TOUCH SLEEP CAUTIONS The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit. Prevent any liquid from falling onto into the remote controller. Do not expose the remote controller to direct sunlight or heat. If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver. If other electrical appliances react to the remote controller, either move these appliances or consult your local dealer. Replacing batteries The remote controller is powed by two AAA dry batteries(r0/lr0x) (RO/LROX) housed in the in the rear rear of part the and remote s protected housing by and a cover. protected by a cover. () Remove the cover by pressing and sliding off. () Remove the old batteries and insert the new batteries,placing the(+) and (-) ends correctly. () Reattach the cover by sliding it back into position. NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.

4 Owner s Manual Room Air Remote Controller Heat Controller, Inc. AAA (),.0 V (dry batteries Lr0x).4V 6 ft (5m) F ~ 40 F (-5 C - 60 C)

5 Heat Controller, Inc. Room Air Remote Controller Owner s Manual Push this button to increase the temperature setting in F/ C increments up to 86 F/0 C. Push this button to increase the temperature setting in F/ C increments down to 6 F/7 C. Push this button, the system will automatically shift to COOL operating with high fan speed, the set temperature is 80 F/0 C. And the timer setting program will be cancelled. Press this button to activate the Sleep mode. This function is available in COOL, HEAT or AUTO mode only and maintains the most comfortable temperature while you sleep. 4

6 Owner s Manual Room Air Remote Controller Heat Controller, Inc. How to use the buttons TOUCH SLEEP Auto operation Ensure the unit is plugged in and power is available.. Press the ON/OFFbutton to start the air conditioner.. Press the button to select Auto.. Press the the TEMP UP/DOWN button button to set to the set desired the desired temperature. temperature. The tempature The temperature can be o O set can within be set a within range of a 6 F/7 C~86 F/0 C range of C/6 F~ in o O o O F/ C 0 C/86increments. F C/ F increments. NOTE.. In In the Auto mode, the air conditioner can can logically logically choose the mode of cooling, Cooling, Fan, or Heating and by by sensing the the difference between between the actual the actual ambient ambient room temperature room temperature and the set and temperature the set temperature on the on remote the remote controller. controller... In In the the Auto mode, you can not switch the fan speed. It It is has already already being been automatically automatically controlled. controlled... If If the a different Auto mode mode is is not desired, comfortable it can be for selected you, the desired manually. mode can be selected manually. Cooling /Heating/ Fan operation TOUCH SLEEP 4 Ensure the unit is plugged in and power is available.. Press the ON/OFF button to start the air conditioner.. Press the button to select Cool, Heat (cooling&heating models only) or Fan mode.. Press the TEMP UP/DOWN button button to set to the set the desired temperature. The The tempature temperature can be can o O be set set within within a range a range of 6 F/7 C~86 F/0 C of C/6 F~ in o O o O 0 F/ C C/86increments. F C/ F increments. 4. Press the FAN button to select the fan speed in four steps- Auto,Low, Med,or High. NOTE In In the Fan mode, the the set setting temperature temperature is not displayed not on the displayed remote in controller the remote therefore controller the room and temperature you are not is not able being to controlled, the room so the temperature up/down either. buttons In this are deactivated. case, only step The, fan is and operational 4 may be only performed. to circulate air. 5 5

7 Heat Controller, Inc. Room Air Remote Controller Owner s Manual e lly TOUCH SLEEP Dehumidifying operation Ensure the unit is plugged in and power is available.. Press the ON/OFFbutton to start the air conditioner.. Press the button to select Dry.. Press the the TEMP UP/DOWN button button to set to the set desired the desired temperature. temperature. The tempature The can temperature set within can a range be set of within 6 F/7 C~86 F/0 C a range of in be o O o O o O 7 F/ C C/6increments. F~ 0 C/86 F in C/ F increments. NOTE In the dehumidifying Dehumidifying mode, mode, the you fan can speed not is switch already the automatically fan speed. It being has already controlled. been automatically controlled. re d. at de. the n gh. TOUCH SLEEP SLEEP operation Press this button button to to activate activate the the Sleep Sleep mode. This mode. function This function is available is available in COOL, on COOL, HEAT or AUTO HEAT or mode AUTO only mode and only maintains and maintain the most the comfortable most comfortable temperatures temperature while you for you. sleep. In this mode, the the selected temperature will will O O increase by F/ C C/ F 0 0 minutes after after the the mode is selected. The temperature will will then O O increase then increase by another by another F/ C C/after F after an additional an 0 additional minutes. 0 This minutes. new This temperature new temperature will be maintained will be maintained for 6 hours for 6 hours before before it returns it to the originally returns to the selected originally temperature. selected temperature. This ends the This Sleep ends the mode Sleep and mode the unit and will the continue unit will to operate continue as to operate originally as programmed. originally programmed. The Sleep mode program can be be cancelled by pressing when press the the, ON/OFF, FAN FAN or the and SLEEP button during operation. 6 6

8 Owner s Manual Room Air Remote Controller Heat Controller, Inc. Timer operation TOUCH SLEEP The Press the button button can initiate can initiate the Auto-start the and Auto-start Auto-stop and program Auto-stop of the setting unit. program The time can of the be unit. set in The range time of can 0~4 be hours. set in range of 0~4 hours. To set the Auto-start/stop time.. Press the button, when the ON indicator displayed on on the the LED LED window of window the air of conditioner, the air conditioner, indicates it indicates the Auto Start the Auto setting Start program is is initiated. When the the OFF OFF indicator indicator displayed displayed on the on LED window the LED of window the air of conditioner, the air conditioner, indicates it the Auto indicates Stop the setting Auto program Stop program is initiated. is initiated.. Press or hold the Up( ) or Down( ) to change the Auto time by 0.5 hour increments, up to 0 hours, then at hour increments up to 4 hours. The control will count down the time remaining until start/stop.. The selected time will register in 5 seconds and the air conditioner will automatically revert back to display the previous temperature setting. 4. Turning the unit ON or OFF at any time will cancel the Auto Start/stop function. NOTE: To cancel the setting, push the button and press or hold the Up ( ) or Down( ) until 0 hour is displayed on the LCD window of the air conditioner. 7 7

9 Heat Controller, Inc. Room Air Remote Controller Owner s Manual COMBINED (Setting both ON and OFF timers simultaneously), AUTO STOP AUTO START (On Stop Start operation) This feature is useful when you want to stop the air conditioner after you go to bed, and start it again in the morning when you wake up or when you return home. Example: TOUCH SLEEP To stop the air conditioner hours after setting and start it again 0 hours after setting.. Press the button until the OFF indicator is displayed on the LED display of the air conditioner.. Use the UP/DOWN button to display ".0" on the LED display of the air conditioner.. Press the button again to display the OFF on the LED display of the unit. 4. Use the UP/DOWN button to display "0" on the LED display of the unit. 5. Wait for 5 seconds until the previous display revert back to the LED window. AUTO START ATUO STOP (Off Start Stop operation) This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house. Example: To start the air conditioner 5 hours after setting, and stop it 8 hours after setting.. Press the button until the ON indicator is displayed on the LED display of the air conditioner.. Use the UP/DOWN button to display "5.0" on the LED display of the air conditioner.. Press the button again to display the OFF on the LED display of the unit. 4. Use the UP/DOWN button to display "8.0" on the LED display of the unit. 5. Wait for 5 seconds until the previous display revert back to the LED window. 8 8

10 /009 04/009