Quality Clockmakers' Supplies Barometer Parts and Materials

Transcription

1 M&P Quality Clockmakers' Supplies Barometer Parts and Materials Please be aware that this document remains available for reference purposes only. This document is outdated and therefore any prices or information within should not be relied upon. An up-to-date version of this document can be found here: For our current catalogue, scan QR code to the left or click here: For our current pricelist, scan QR to the right or click here: Tel: Fax: Automated sales: Meadows & Passmore Ltd

2 Case ornamentation BRASS HANDLES For carriage and bracket clocks. The wires can be adjusted slightly to suit existing handle centres. 54 x 36mm x 25mm P&P units P&P units BRASS ESCUTCHEONS HANDLES, LOCKS & LATCHES For longcase doors. 3 3/4" long, 1" wide. Solid brass P&P unit Polished and lacquered flat brass escutcheon for small locks on bracket and grandmother clocks, musical boxes and jewellery cases. 25mm x 10mm x 1mm P&P unit 62 x 27mm P&P units Oval brass escutcheon. 36mm high x 27mm wide P&P unit 88 x 35mm Flat brass escutcheon. 1mm thick P&P units P&P unit KEYHOLE INSERT Solid brass insert. 10mm x 18mm P&P unit BRASS BOX CORNERS Solid brass, suitable for musical boxes and writing slopes. A mm B mm BRASS MIRROR PLATE Solid brass. 3.9cm width. 3.9cm height B A BRASS DOOR LATCH FOR O.G. & STEEPLE CLOCKS. Solid brass construction P&P unit ROUND BRASS DOOR LATCH Suitable for almost any clock door P&P unit P&P unit 1 P&P unit BRASS DOOR KNOB Gothic style P&P unit P&P unit P&P unit P&P unit BRASS DOOR CATCH For American & German clocks P&P unit 2 PIECE BEZEL LATCH Knob screwed to bezel fits into catch P&P unit P&P unit BRASS PENDANT KNOBS BRASS TURNS For drop dial clock doors etc, P&P unit A. Screw mounting 23mm drop B. With mounting plate 32mm drop C. Antique style 38mm drop mm drop BRASS DOOR HOOKS & EYES Left handed means that the eye goes on the door and the latch fits the left of the case. 3/4" L.H /4" R.H " L.H " R.H M&P 2003 C P&P units P&P units BRASS PIVOT HINGES For Steeple clocks. Sold in pairs P&P unit LONGCASE HOOD BLANK Solid brass. Sold in pairs P&P units P&P unit P&P units REPEAT KNOB Typical bracket style, solid brass. 15mm long, 10mm at the widest point. Recessed for knot P&P unit P&P unit P&P unit P&P unit P&P unit CARRIAGE CLOCK DOOR KNOB Knurled brass knob with threaded stem. 6mm diameter head. 4mm deep P&P unit Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax /1

3 BRASSWARE & FITTINGS Case ornamentation PRESSED BRASS HINGES For clock doors. Measured open. Sold individually. Ht. Width 1/2" x 1/2" /4" x 1/2" BUTT HINGES Solid brass. Unequal sides. Width 13/16" + 9/16". Sold individually. Height 1" /4" STRAP HINGE Made from solid polished brass. 73mm long x 38mm high. Plate size 20 x 20mm P&P units 45mm high x 20mm wide P&P units SPIRE & EAGLE BALLS Polished brass ornaments complete with wood screw in base. Height excludes the screw. Small balls are 28mm wide, larger are 48mm. Spire 75mm Spire 115mm Eagle 75mm Eagle 115mm CAST BRASS ROSETTES Suitable for pinning to wood. CAST BRASS FINIALS Dia. Part number Height excludes screw. 25mm P&P unit 25mm high x 12mm wide 36mm P&P unit P&P unit PRESSED BRASS ROSETTES Complete with pin. Dia Part number 35mm high x 18mm wide 14mm P&P unit 17mm P&P unit P&P units 20mm P&P unit 30mm P&P unit 50mm P&P units 70mm high x 35mm wide P&P units Burgundy P&P unit Green P&P unit MOVEMENT STRAP For securing French movements to their cases. 150mm long. Includes a 4BA 2" screw. Sold individually LONGCASE SEATBOARD HOOK Steel wire with brass nut. 1/8" 3.2mm /32" 4mm PIN-ON BUTTONS Sold in packs of P&P unit P&P unit P&P unit P&P unit P&P unit P&P unit Flower Oxidised brass 17mm diameter P&P units 20% POLISHED BRASS PILLAR CAPS Capitals. Max height 20mm Pillar Base Part dia. width number 19mm 31mm mm 31mm mm 35mm mm 41mm PERFORATED BRASS SHEET Polished on one side. For fretwork in doors and sides of clock cases. 300 x 145mm sheets P&P units BACKING FABRIC 12" x 6" pieces of synthetic backing silk. REEDED BRASS TUBE Ready for polishing and lacquering, this brass tube is ideal as a replacement for any architectural style clock case needing new columns. It fits pillar cap Specifications: 3/4" diameter. 0.32" wall thickness. 9" long. AMERICAN METAL BACKPLATE For clocks that imitated the French. 4 1/2" /4" P&P units 5 P&P units OFFICE DIAL CASE PEG Turned beech. Tapers from 10mm at the shoulder to 6mm at the tip P&P unit P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units Tube P&P units P&P unit Pillar cap P&P units 9/2 Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax M&P %

4 Case ornamentation WALL CLOCK CASE PARTS VIENNA STABILIZERS Sold in pairs, suitable for all sizes of Vienna clock P&P unit VIENNA SCALE Enamelled 76mm x 31mm VIENNA REGULATOR ORNAMENTS Dark resin. 'Eagles' 110 x 180 wide x 180 wide 'Horses' 170 x 145 wide x 210 wide P&P units P&P units P&P units P&P unit P&P units Porcelain 56 x 22mm x 24mm BRASS VIENNA SCALE Solid brass scale or beat plaque to show the swing of the pendulum. 77mm x 32mm. Numerals and scale are recessed for filling with engravers wax if required P&P unit VIENNA MOVEMENT FASTENERS 4mm steel screw with knurled brass head. 54mm long. Nickel plated plates. Sold in pairs P&P unit UNFINISHED VIENNA REGULATOR CROWNS Ready to be stained/polished. Crown No. 1 Made of solid hand-carved walnut, ready for polishing. 300mm x 87mm P&P units Crown No 3 Walnut veneered, ready for assembly and finishing. 350mm x 230mm P&P units Crown No 4 Quality ply, ready for assembly and finishing. 370mm x 268mm P&P units P&P unit P&P unit WOODEN ROSETTES Pressed. Size Part number 31 x 9mm x 12mm x 9mm CAST VIENNA MASK Made from a compound that can be stained & varnished. 40 x 53 x 20mm P&P units HIGH QUALITY VIENNA CROWNS Finished and ready for waxing to match the case. Beautifully hand made to match antique cases. Crown no mm x 150mm P&P units Crown no mm x 175mm P&P units Crown no mm x 125mm P&P units P&P unit P&P units P&P units UNFINISHED VIENNA REGULATOR BOTTOM Ready for sanding & polishing. Bottom No 2 Made from solid walnut and ready for polishing. 80mm high. 166mm x 116mm at the top. 74mm x 67mm at the bottom P&P units Bottom No 11 Solid walnut exterior. Pre-sanded. Height 95mm. Top 195 x 120mm. Bottom 50 x 50mm P&P units M&P 2003 Crown no mm x 145mm P&P units HIGH QUALITY VIENNA BOTTOM Finished and ready for waxing to match the case. Bottom no. 10 Height 120mm. Top 240mm x 120mm Bottom 125mm x 65mm P&P units Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax /3

5 FEET & HANDLES, FINIALS Case ornamentation BUN FEET Solid brass, polished. All 12mm high. Dia. Part number 15mm mm mm mm mm BRASS CADDY FOOT Solid brass. 13mm mm BRASS KNOB OR FOOT No 2 3/8" wide by 3/8" high, excluding woodscrew P&P unit BRASS FOOT OR KNOB No. 3 1/2" Wide. 1/2" High excluding woodscrew WOODEN FINIALS Made from turned beech P&P unit P&P unit P&P unit P&P unit P&P units P&P units P&P units BRACKET FOOT 4+ Plain polished brass.12mm high. Base 15% sides 28mm long. Upper sides 40mm % P&P unit 'AMERICAN' CAST FEET Cast from hard metal and spray gilded to suit American copies of French marble clocks. 60x60x55mm. 20mm from ground to bottom of clock. Sold in sets of four P&P units LIONS HEAD HANDLES Cast from hard metal and spray gilded. 2" x 2 1/4" excluding ring. Not suitable for carrying the clock with! Sold in pairs P&P units EARS FOR DROP DIAL CLOCKS Hand carved from hardwood, ready for finishing. Suits most drop dial cases. 60mm x 240mm at the widest points. Sold in pairs only P&P unit P&P units No. Height Width Part no. 1 22mm 10mm mm 20mm mm 20mm mm 30mm mm 26mm mm 38mm mm 52mm mm 44mm mm 39mm mm 49mm mm 44mm mm 40mm mm 32mm mm 45mm mm 44mm mm 49mm mm 48mm mm 46mm mm 45mm mm 51mm mm 74mm mm 67mm mm 64mm mm 72mm mm 65mm mm 33mm P&P unit P&P unit P&P unit P&P unit P&P unit P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units P&P units We can supply other wooden finials to special order. If you do not see what you want, please send a sketch and we will let you know what we can offer /4 Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax M&P 2003

6 Case ornamentation CLOCK CASE PARTS CUCKOO BIRDS Plastic body with moving bill. Painted wings. 78mm long. Metal foot & clamp screw. Multi-coloured P&P unit Wooden bird for cuckoo clocks. Coloured bill, but rest of bird needs painting to suit. No moving wings. 20mm high. 87mm long CUCKOO CLOCK TOPS Carved wooden tops for cuckoo clocks. Unstained, but sanded and ready to fit. 215mm x 130mm P&P units 240mm x 155mm P&P units 295mm x 185mm P&P units...or anti-clockwise Numbered and going anti-clockwise, the 'Blackstone' clock is an amusing and reliable timepiece; hang one on the wall and see who notices! Battery operated quartz wallclock. Circular white plastic case with metal dial. Often to be seen in bars, hotels and kitchens. STAGS HEAD & ANTLERS Plastic stags head with antlers finished with dark varnish appearance. As used on modern reproductions of cuckoo clocks. Height includes antlers. 110mm P&P units 130mm Not available 150mm P&P unit P&P units P&P units GLASS RETAINING STRIPS 12" strips of wood to hold glass in position on O.G's etc. 1/4" x 1/ 8". Packs of four strips MARBLE EFFECT PAPER For covering imitation marble pillars etc. Simply glue in place and varnish over with ordinary lacquer. Appx. 6" x 21" sheet P&P units P&P units WOODEN LONGCASE FEET Set of four quality replacement feet for Longcase clocks. Front feet 90mm x 90mm x 65mm high. Rear feet allow the case to touch the wall, so are only 55mm x 65mm x 65mm high. Ready for polishing. Mahogany P&P units Oak P&P units SETTING UP & REGULATING PENDULUM CLOCKS How many times have you had to explain to customers that they don't need to put a coin under one corner? Hand out a copy of this leaflet with every repair, after stamping your name in the box provided, and cut down on wasted time. It will stay with the clock and ensure your name is there when it needs servicing again. Sold in packs of 100 double sided A5 leaflets P&P units SETTING UP AND REGULATING ANNIVERSARY CLOCKS To compliment our setting up sheet for conventional clocks, this sheet describes the siting, regulation and setting up of 400 day or Anniversary clocks. Hand one out with every 400day repair, after stamping your name in the box provided, and cut down on wasted time. It will stay with the clock and ensure your name is there when it needs servicing again. Sold in packs of 25 double sided A5 leaflets M&P P&P units Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax /5

7 CABINET LOCKS & KEYS Case ornamentation CABINET MORTICE LOCK & KEY Solidly constructed brass lock & key for clock cases and small boxes. Mortice type. 52mm key. Face plate 8mm x 46mm. Complete with escutcheon. Box 17mm x 27mm x 4mm. L/H P&P units R/H P&P units CUT DOOR LOCKS Brass construction with steel key. 1 1/2" Lock Faceplate 10mm x 38mm Box plate 28mm x 38mm Box 23mm x 25mm x 6mm 2" Lock Faceplate 10mm x 51mm Box plate 28mm x 51mm Box 25mm x 32mm x 6mm Type Hand Part no. 1 1/2" L " L " R BRACKET CLOCK CUT LOCK - Double handed Solid brass lock for bracket clocks whose keyholes are on the side of the case. Also suitable for musical boxes & jewel cases etc. Faceplate 8 x 38mm. Box plate 19 x 38mm. Box 18 x 25 x 6mm. Antique pattern forged key P&P units MINI CUT LOCK - Double handed Brass, with locking pin which fits into the door or lid to be secured. Ideal for small writing slopes and jewellery boxes. Faceplate 6 x 40mm. Box plate 18 x 40mm. Box 15 x 28 x 4mm P&P unit P&P units 2 P&P units BOX MORTICE LOCK -Double handed Brass lock with key and escutcheon. Catch fits into the door or lid to be secured. Faceplate 8mm x 46mm. Box 15 x 28 x 4mm P&P units P&P unit Cut locks: These are cut into the back of the door or drawer leaving the outer box and faceplate visible. Mortice locks: These are cut into the edge of the door or drawer leaving just the faceplate visible. Handing: Based on the English handing system, a lock is described as left or right hand when the bolt shoots to the left or right. i.e. the bolt of a lefthand lock shoots to the left when locked. Double-handed locks are suitable for both left and right hand fitting. DOOR KEY BLANKS A range of key blanks to suit clocks and antique furniture etc. Most old cabinet locks are easy to cut a key for, but if necessary they can be taken to any locksmith. Most locksmiths only stock modern style blanks. Plain oval bow - Steel LengthPart number 1" long /4" /2" long P&P unit P&P unit P&P unit Cast fancy keys - Nickel steel alloy Ni/Fe105 (shown actual size) Length Style Part number 25mm P&P unit 35mm P&P unit 45mm P&P unit 54mm P&P unit 55mm P&P units 69mm P&P units Plain oval Style 1 (25mm) Style 4 (35mm) Style 6 (45mm) Style 8 (54mm) Style 10 (55mm) Style 9 (69mm) 9/6 Meadows & Passmore Ltd. Brighton BN41 1EU Tel Fax M&P 2003