Pump Mounting Hardware

Transcription

1 Pump Mounting Hardware provides a complete line of pump mounting hardware from clamps, wall brackets, covers, elevators and rams to a variety of stands and carts. So whether you need to mount your pump on the wall, on a drum, or move it to another location, gives you rugged hardware to fit your pump for every application. Sturdy wall mount brackets save floor space and enable container changes. Elevators conveniently raise and lower heavy pumps. Rams provide pump support while pressure-feeding pumps. Carts and dollies make your pumps portable. Stationary stands, wheel kits and bases provide added flexibility. Reinforced, heavy gauge drum covers support pumps on open drums. Drum and tank clamps stabilize your pumps on the fluid container. AMR SOLVENT COLOR 1 COLOR AMR PRIMER 1 CATALYST PRIMER FLUID HANDLING ACCESSORIES 19

2 Wall Brackets & Plates Quality-made wall shelf brackets support pumps and free-up floor space Fast-Flo Sturdy, compact. Cast iron Husky 307, 515, 716 Wall mount, pump Painted mounting holes Husky 1040 Rigid 11 gauge wall Painted bracket Fast-Flo 1:1 Mounts pumps with Steel, Fire-Ball 5:1-1 8 in (54 mm) dia. cast iron Dyna-Star 1:1 riser tubes. Steel Eagle 3:1 strap for securing pump President 10:1 to cast iron V-Block Dyna-Star 1 4:1 Mounts pumps with Steel, Power-Star 1:1 4 in (10 mm) dia. cast iron President 3:1 riser tubes. Steel strap for securing pump to cast iron V-Block Monark, President, Includes all screws, Painted Viscount in-line washers and nuts for and 3-tie-rod divorced fastening pump to stubby pumps bracket Monark, President, Includes all screws, Painted Viscount in-line washers and nuts for and 3-tie-rod divorced fastening pump to stubby pumps bracket. 060 Monark, President Includes all fittings for Painted and Viscount II mounting pumps and stanchion tube paint filter. Order divorced pumps adapter plate separately to mount 3-tie-rod divorced stubby pumps. 061 Husky 1040, Senator, Includes gasket, screws, Painted Bulldog, King, Viscount II, washers and nuts for 3-tie-rod divorced fastening pump to bracket. stubby pumps, Glutton and mid-range High-Flo Monark and Adapts Monark 3-tie-rod Painted Viscount I divorced stubby pump to fit 060 bracket or drum cover Dual stanchion tube for Provision for mounting Steel Monark, President and paint filter/outlet manifold. Viscount to either stand or Check-Mate pumps Used with 781 ram. Painted Monark and President Used with ram. Painted pumps FLUID HANDLING ACCESSORIES

3 Elevators, Tubes and Controls Provides pump support when pump is raised and lowered to change pails or drums. 10 Gallon (38 Liter) Pail Elevators 0533 Use with 10 gal (38 l) Air fitting for quick coupler Steel cover and restrictor valve gal (38 l) pail elevator Order pail truck Steel not good for divorced separately to use with Fire-Ball, units (will not clear tierods) Monark and President pumps Fast-Flo, Fire-Ball Includes cover 0413 Painted 3065 and elevator Gallon (61 Liter) Drum Elevators 0411 Fire-Ball Use with 0413 cover Steel 3065 to mount Fire-Ball pumps to 10 lb. (54.4 kg) drum. 5 Gallon (19 Liter) Inductor Plate Fits collar.69 in Steel (68.3 mm) ID FLUID HANDLING ACCESSORIES 1

4 55 Gallon (10 Liter) Drum Elevators Fire-Ball, Monark, Includes elevator 0631, Steel President pump support 37578, and air control kit Fire-Ball, Monark, Includes elevator 04385, Steel President cover- air control valve 37579, mounted pumps floor mount base and drum cover support Fire-Ball, Monark, Includes elevator Steel President in-line and and bracket divorced design pumps without drum cover or bung adapter Fire-Ball, Monark Elevator only with Steel President stationary base Bulldog, King Includes elevator 07408, Steel pump support 37578, and air control kit Elevator Retrofit Kit Designed to adapt elevators with Steel old support ring to fit new SST drum covers thru 37310, 19006, and others. Drum support not included. 55 Gallon (10 Liter) Drum Elevator Base Plates Part No. Features Material Manual Provides stable surface if floor is too Steel irregular for proper operation. Use with and Gallon (10 Liter) Drum Inductor Assembly Inductor assemblies include elevator, pump bracket, inductor plate, up/down control, air hose and floor base plate. Part No. Features Material Manual Monark (4350) and President (4348). Steel Includes elevator, inductor plate, pump bracket, up/down control, air hose and base. Requires pump adapter Also requires flange (160754) Bulldog 5:1, 33:1 and Steel King 45:1. Features same as FLUID HANDLING ACCESSORIES

5 55 Gallon (10 Liter) Drum Inductor Plate Part No. Features Material Manual Fits collar. in ID. Steel, Rubber 55 Gallon (10 Liter) Drum Cover Lift Support Part No. Features Material Manual For drum cover-mounted pumps. Requires Painted support arms to attach cover to elevator. Fits 04385, 3790 and Gallon (10 Liter) Drum Wishbone Frame Support Fire-Ball, Monark, Wishbone support and President in-line pump controls for up/down. 063 Bulldog, King Adjustable bracket attaches to Zinc-plated elevator tube Gallon (10 Liter) Air Control Kits Part No. Pump Support Features Manual 0676 Bulldog or King pump Includes air regulator with gauge mounted on a heavy- restrictor valve, push-pull valve, duty elevator air-assist valve, hose and fitting for directing air to pump, elevator and inductor plate Elevator up/down control Air control kit similar to 0676; plus includes air tube and mounting bracket to locate push-pull control on front edge of stainless drum cover FLUID HANDLING ACCESSORIES 3

6 Pail Carts For job site mobility, offers compact, stable carts and dollies. Available with various frame and tire sizes. Portable Carts and 10 gallon Two wheel cart with handle. Painted, (19 and 38 liter) pails Holds pail with pump. Use rubber wheels with Monark, President, Compact, stable cart with Painted, Viscount II with pneumatic tires, double rubber wheels 3-tie-rod design and grip handle, heavy-duty displacement pump support pads. Handle length less than supports large hose coil. 0.5 in (5 cm) 403 Monark Stubby, Light duty cart features Painted, Husky 307 single handle, hose hook rubber wheels pump/air control bracket Senator, Bulldog, Similar to 403 Painted, (Xtreme) King, Viscount II but more strength rubber wheels with fluid displacement for heavier pumps and pump length less than large hose coils. 30 in (76 cm) 4457 New lightweight cart Painted, for Senator, Bulldog, rubber wheels King Pumps 4137 Exclusively for Same as plus Painted, Check-Mate pumps air lift elevator for raising rubber wheels pump Premier Welded frame. Painted, rubber wheels Band Dolly gallon (19 liter) pails Attaches to pail base. Painted, Large swivel wheels. rubber wheels and 16 gallon Attaches to pail base. Painted, (38 and 61 liter) Large swivel wheels. rubber wheels drums. Also 5, 10, 15 gallon (19, 38, 56.8 liters) pressure pots FLUID HANDLING ACCESSORIES

7 Pump Rams Stable, secure ram designs hold pumps in place during operation or above container while changing containers. Available in pail and drum styles. Puts pressure on high viscosity fluid surface to force material into pump inlet. 5 Gallon (19 Liter) Single Post Pail Ram Senator, Bulldog, Supports pump on CS King. Use adapter pneumatic post. Pump plate 165 to bracket, air regulator, support Monark and 5 gallon (19 liters) pail ram, President. welded floor plate and ram wiper plate. 781 Exclusive use with Same as CS Check-Mate pumps. Use adapter plate to support Monark and President Bulldog Mount Narrow tie rod CS Bulldog Mount Wide tie rod CS Gallon (19 Liter) Two Post Pail Ram Bulldog, King, Extra sturdy design. Dual Painted Viscount II pneumatic posts for extra pressure needed for viscous fluid evacuation through pump inlet. Air controls included. (Order air regulator and ram follower plate separately.) 5 Gallon (19 Liter) Plate Shields Part No. Features Material 3689 Ten disposable shields Polyethylene for 5 gallon (19 liter) pails Gallon (10 Liter) Two Post Ram :1, 39:1, 45:1, 80:1 Premier; Dual pneumatic 6.5 in (165 mm) CS :1, 50:1, 65:1 King; posts. 15 psi (8.6 bar, 0.8 MPa) max. 1:1, 31:1 Bulldog; inbound air pressure. (Order air 19:1 Senator; controls, ram plates, cross-over Viscount Hydraulic kit separately.) FLUID HANDLING ACCESSORIES 5

8 55 Gallon (10 Liter) Two Post Drum Rams 0779 Monark, President, Includes ram unit, 3 in (76. mm) Painted Senator, Bulldog, diameter posts, adjustable pump mount, King, Check-Mate, 55 gallon (10 liter) ram plate Dura-Flo pumps. Requires with double wiper rings, air 776 mounting kit. controls, and 4 in x 5 in Adapter plate 165 (107 cm x 63 cm) base plate. required to mount Monark (Order air regulator separately.) and President Wiper Ring Replacement Kit. Easy to install. Superior wiping performance. Kit for 0779 ram plate includes two wiper rings and four retainer bands ram without a plate C ram without a plate or rods Gallon (10 Liter) Drum Clamps Part No. Features Material Sturdy clamps hold drum Grey iron casting centered on base plate in alignment with ram for proper operation. Clamps hold empty drum down while ram is being lifted out is a set of clamps Gallon (10 Liter) Double Ram Changeover Part No. Features Pneumatic control automatically switches air supply from one pump to a second pump when supply container empties. Allows uninterrupted supply. 55 Gallon (10 Liter) Low Level Cut-Off Alarm Part No. Features Provides audible alarm to alert operator that drum is empty. 55 Gallon (10 Liter) Plate Shields Part No. Features Material 79 Ten disposable shields for Polyethylene 55 gallon (10 liter) drums FLUID HANDLING ACCESSORIES

9 Stands and Bases Pump support in a wide variety of sizes to match your installation requirements. Bases 036 Fits 5, 10, 16 gallon Four swivel wheels support Painted (19, 38, 61 liters) sturdy platform. Hold-down containers clamps and secure pail to platform. 036 Stands Pumps with threaded intake Sturdy, wide stance Cast iron, and fluid displacement pump support. Need adapter cylinder length less to fit Monark and than in (150 mm) President pumps Pumps with threaded intake Sturdy, wide stance Cast iron, and fluid displacement pump support. Need adapter cylinder length of to 33 in to fit Monark and (550 to 840 mm) President pumps High-Flo with high volume Extra sturdy floor stand. Painted and high flow surge tanks 0581 High Flo mid-range Extra sturdy floor stand. Painted with 0xxx part no Foam-Cat proportioning Sturdy and stable design. Steel pump and heater FLUID HANDLING ACCESSORIES 7

10 Pail & Drum Covers sturdy covers support a wide array of pumps. Choose from pail or drum covers. 5 Gallon (19 Liter) Pail Covers Monark 3:1 Agitator mounting port. Secure Painted cover and adjust pump height with thumbscrews 1000 (3) and spacer (1). (Order separately.) Monark 3:1, Agitator mounting port and fill- Alum Standard :1 port. Secure cover to pail with latch hooks 04534, latch handles 04535, pivot pins , washers 1583, and cotter pins (Order separately.) 065 Fire-Ball 15:1 Secure cover and pump to Painted pail with lock washers , cap screws 1000, and thumbscrews 1000 (3). (Order separately.) 058 Fire-Ball 15:1 Same as 065. Painted Includes all fasteners Husky 515/716 Agitator mounting port, Painted suction tube and mounting hardware. 430 Standard :1 Kit includes SST cover 465, SST pail flange , screws, plastic 1 in (5.4 mm) plug and thumb screw. 401 Husky 307 SST President 30:1 Use with spacer Waterborne compatible Gallon (38 Liter) Pail Covers Fire-Ball 50:1 Thumbscrews and Painted rubber gasket. Steel FLUID HANDLING ACCESSORIES

11 16 Gallon (61 Liter) Drum Covers Fire-Ball 50:1/15:1/5:1; Thumbscrews and cover Painted Fast-Flo, hand gasket. Adapter plate lever pumps (Order separately.) 0413 Fire-Ball 50:1/15:1, Includes rubber gasket. Painted 3065 Fast-Flo 1:1 Use with elevator tube (Order separately.) Fast-Flo requires adapter plate (Order separately.) 0469 Fire-Ball 50:1/15:1 Hold down rods, brackets Painted and rubber gasket Gallon (10 Liter) Drum Covers for Lube Pumps 0036 Fire-Ball 50:1/15:1, Center mount for Painted President 10:1 open head drums Fire-Ball 5:1, Tie-rod attachment Painted President 10:1 to drum Fire-Ball 50:1/15:1 For in-line pumps. Painted See also drum cover with agitator 07199, page FLUID HANDLING ACCESSORIES 9

12 55 Gallon (10 Liter) Drum Covers for Paint Pumps & Agitators President, Includes inspection port plug, 304 SST Monark, bolts, nuts, and gaskets. Standard and Fits agitator and siphon Fast-Flo tube President and Includes inspection port plug, 304 SST Monark bolts, nuts, and gaskets. Fits agitators and President (two bolt mounting) Includes inspection port plug, 304 SST bolts, nuts, and gaskets. Fits agitators 04995, 0619 and filter King, Bulldog, Includes inspection port plug, 304 SST Senator, and bolts, nuts, and gaskets. President Fits agitator and air regulator (King), and air regulator 0571 (Bulldog) Standard Includes inspection port 304 SST plug, bolts, nuts, and gaskets. Fits agitators 04995, 0619 and filter Glutton Features inspection port plug, 304 SST agitator port; return tube ports, Glutton bolt holes and siphon tube port Most pumps Features only inspection port with 304 SST except Premier plug. No other holes. Additional holes cut to fit particular application Most pumps Blank cover with no holes. 304 SST except Premier Heavy duty 1 gauge SST. Not passivated Fits agitator Includes inspection port, 304 SST return port and mounting holes for agitator. Waterborne compatible Drum Cover Accessories Part No. Pump Support Features 3754 Optional Handle Kit Includes two SST handles and fasteners Drum Lip Gasket Disposable snap-fit gasket provides seal between top of drum and underside of drum cover to minimize evaporation. Note: See elevators and drum cover support accessories on pages 1-3. For bung adapter flanges see page 31. Waterborne compatible FLUID HANDLING ACCESSORIES

13 Drum Bung Adapters & Flanges adapters allow pumps to be threaded into in npt bung openings. Supports a wide array of pumps. Drum Bung Adapters Mount lightweight lever Use with Sturdi-Clamp Steel pumps with -1 8 in (54 mm) Includes diameter riser tubes O-ring seal Same as except Steel 4579 is air tight Stainless pumps Includes thumbscrew Steel with -1 8 in (54 mm) to secure pump riser tube diameter riser tubes at adjusted height. (Order non-corrosive Sturdi-Clamp to mount pump on side of open head drum or tank separately.) Carbon pumps in npt(m) thread. Use with Carbon with in diameter. Sturdi-Clamp to mount pumps on open head drum or tank. (Order separately.) 308 Fits Fast-Ball, Eagle, Includes bolt. Steel Fire-Ball, President.15 diameter Fits Fast-Flo 1:1 Air tight, includes O-ring, diameter Steel Fits Fire-Ball 15:1, 50:1 and 80: Drum Flange Mounting for bung adapter in npt(f) opening for Aluminum equipped with carbon bung adapter. pumps on open head drum Four bolt holes. when used with drum covers or 0036 (order separately) Use with drum cover Three bolt holes Cast iron Use with drum cover Three bolt holes 304 SST Waterborne compatible FLUID HANDLING ACCESSORIES 31

14 Sturdi-Clamps clamps hold pumps secure and upright in drum or tanks Fast-Flo 1:1 For in (50.8 mm) tube, in-line only. CS Carbon pumps U-bolt to clamp pump CS with -1 8 in (54 mm) dia. at proper depth. riser tubes. For in-line pumps only Carbon pumps U-bolt to clamp pump CS with -1 8 in (54 mm) at proper depth. In-line dia. riser tubes in pumps only. bung hole of closed head drums when used with bung adapter Stainless pumps in npt(f) opening for Cast iron, using SST bung open head drums. nickel-plated, adapter CS Grounding Clamp Part No. Pump Support Features 011 Grounding wire and clamp 7.6 m (5 ft), 1.5 mm (10 gauge) FLUID HANDLING ACCESSORIES