Whitman Twin over Full Bunk Bed Model # WHMTFBB
|
|
- Hope Quinn
- 7 years ago
- Views:
Transcription
1 LOT NUMBR: DAT PURCHASD: / / Whitman Twin over Full Bunk Bed ADULT ASSMBLY RQUIRD If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday Or visit our web site 24 hours a day, 7 days a week for product assistance at Or your request to parts@whalenfurniture.com THIS INSTRUCTION BOOKLT CONTAINS IMPORTANT SAFTY INFORMATION. PLAS RAD AND KP FOR FUTUR RFRNC. Whalen Furniture Manufacturing Page 1 Factory No Date Rev. 2 Factory: WOFUVI
2 QUALITY GUARANT We are confident that you will be delighted with your purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. very our product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from State to State. Customer Service: :00 a.m. - 5:00 p.m., CST, Monday to Friday ALWAYS US GUARDRAILS ON BOTH LONG SIDS OF TH UPPR BUNK. IF TH BUNK BD WILL B PLACD NXT TO TH WALL, TH GUARDRAIL THAT RUNS TH FULL LNGTH OF TH BD SHOULD B PLACD AGAINST TH WALL TO PRVNT NTRAPMNT BTWN TH BD AND WALL. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts, and jump ropes. Prohibit more than one person on upper bunk. Mattress thickness is from 7 in. (18 cm) to 9 in. (23 cm) use on lower bunk bed, and maximum mattress thickness must not exceed 9 in. (23 cm) use on upper bunk bed. Surface of mattress must be at least 5 in. (12.7 cm) below the upper edge of guardrails. Use only mattress which is 74 in. (1.88 m) to 75 in. (1.9 m) long and 37 ½ in. (95 cm) to 38½ in. (98 cm) wide on upper bunk. Use only mattress which is 74 in. (1.88 m) to 75 in. (1.9 m) long and 52 ½ in. (1.3 m) to 53 ½ in. (1.4 m) wide on bottom bunk. Replacement parts, including additional guardrails, may be obtained from any of Whalen Furniture dealer. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 2 Factory No
3 TO HLP PRVNT SRIOUS OR FATAL INJURIS FROM NTRAPMNT OR FALLS Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls. Surface of mattress must be at least 5 in. (12.7 cm) below the upper edge of guardrails. Do not allow children under years of age to use the upper bunk. Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage and that all connectors are tight. Do not allow horseplay on or under the bed and prohibit jumping on the bed. Always use the ladder for entering and leaving the upper bunk. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts. Use of a night light may provide added safety precaution for a child using the upper bunk. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall. The use of water or sleep flotation mattress is prohibited. STRANGULATION HAZARD Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited to, hooks, belts, and jump ropes. Prohibit more than one person on upper bunk. Keep these instructions for future reference. This product was manufactured November Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 3 Factory No
4 Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Lower Post (2) B- Lower Post (2) C- Lower Cap Rail (2) D- Lower Cross Assembly (2) - Upper Post (2) F- Upper Post (1) G- Upper Post (1) H- Upper Cap Rail (2) I- Upper Cross Assembly (2) J- Back Mattress Side Rail (2) K- Lower Ladder Side Rail (1) L- Upper Ladder Side Rail (1) (With 2 through holes for ladder) (With 2 female connectors) Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 4 Factory No
5 Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. M- Long Guardrail (2) N- Short Guardrail (2) O- Lower Mattress Support Slats (1) P- Upper Mattress Support Slats (1) Q- Left Ladder Support (1) R- Right Ladder Support (1) S- Ladder Step (4) T- Front Guardrail Post (1) U- Guardrail Support (2) V- Removable Decor (8) W- Slat Support with Leveler (3) X- Wood Filler Block (4) Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 5 Factory No
6 Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Ø1/4 x 110 mm Bolt (2) Ø1/4 x 38 mm Bolt (24+1 extra) (9+1 extra) (3) Ø.5 mm x 100 mm Tapping Bolt (4) Ø.5 mm x 48 mm Tapping Bolt (1+1 extra) (24+1 extra) (5) Ø1/4 Barrel Nut (24+1 extra) () Ø10 mm x 50 mm Wood Dowel (48+2 extra) (7) Ø4 mm x 30 mm Screw (42+2 extra) (8) Floor Protector (4+1 xtra) (9) Ø4 mm x 0 mm Wood Screw (8+1 xtra) (10) Bed Connector Pin (4) L-shaped Allen Wrench (1) T-Handle Allen Wrench (1) Tools required: Allen wrench (provided) and Phillips screwdriver (not provided). Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page Factory No
7 ASSMBLING LOWR HADBOARD/FOOTBOARD Ø.5 mm x 48 mm Tapping Bolt (8 used in this step) 4 Ø10 mm x 50 mm Wood Dowel (4 used in this step) 1. Unpack the units and confirm that you have all hardware and required parts. 2. Locate one Lower Cap Rail (C) on a level and protected surface with the holes facing up. Insert two Wood Dowels () into the large holes of one Lower Cross Assembly (D) and attach to the Lower Cap Rail (C) using four 48 mm Bolts (4). Securely tighten the bolts with the enclosed L-shaped Allen wrench. As shown above. 3. Repeat last step to combine the other Lower Cap Rail (C) and the other Lower Headboard Assembly together. Make sure that the drilled holes for Connector Pins will be symmetric. As shown above. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 7 Factory No
8 ASSMBLING LOWR HADBOARD/FOOTBOARD Ø.5 mm x 100 mm Tapping Bolt (8 used in this step) 3 Ø10 mm x 50 mm Wood Dowel (12 used in this step) 4. Insert six Wood Dowels () into the large holes of the Lower Cross Assembly (D) at both ends. Align and attach one Lower Post (A) and one Lower Post (B) to one Lower Cross Assembly (D) with four 100 mm Tapping Bolts (3) as shown. Be sure the pilot holes on the cross assembly and the cutout on the post face the same direction. 5. Repeat the same procedure with the other Lower Cross Assembly (D). Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 8 Factory No
9 ASSMBLING LOWR HADBOARD/FOOTBOARD A B D V 9 x 2 9 V Ø4 mm x 0 mm Wood Screw (4 used in this step) 9. Align and attach one Removable Decor (V) to each Post (A and B) with one 0 mm Wood Screw (9) as shown. Make sure that the curved edge of Removable Decor (V) will face the floor when the unit is turned upright. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 9 Factory No
10 ASSMBLING LOWR HADBOARD/FOOTBOARD A B X X 7 D 7 x 2 Ø4 mm x 30 mm Screw (8 used in this step) 7 7. Use the pilot holes as a guide, align and attach 2 Wood Filler Blocks (X) to the bottom rail of one Lower Cross Assembly (D). Insert one 30 mm Screw (7) through each countersunk hole on the Wood Filler Blocks (X) and screw into the Lower Cross Assembly (D). Securely tighten the wood screws with a Phillips screwdriver. As shown above. 8. Repeat the same procedure with the other Lower Headboard Assembly. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 10 Factory No
11 ASSMBLING LOWR BUNK A B J K 1 5 A D J B B D K A Ø1/4 x 110 mm Bolt (8 used in this step) 1 Barrel Nut (8 used in this step) 5 NOT: Please follow the instructions carefully to insure a safe and sturdy bed. Do not fully tighten the bolts until all rails and guardrails are attached. 9. Insert 2 Barrel Nuts (5) into each end of the Back Mattress Side Rail (J) and Lower Ladder Side Rail (K). Be sure that the cross slot on the Barrel Nut faces out and that the long groove points towards the entry of the Bolt. 10. Bolt the Back Mattress Side Rail (J) and Lower Ladder Side Rail (K) between the Lower Posts (A and B) as shown above, using the 110 mm Bolts (1) through the drilled holes on the Posts and screw into the Barrel Nuts (5) in the Side Rails (J and K). Make sure the wood stoppers attached to the Mattress Side Rail for slats are up and face inward. Tighten the bolts with the enclosed Allen wrench. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 11 Factory No
12 ASSMBLING UPPR HADBOARD/FOOTBOARD I 4 Ø.5 mm x 48 mm Tapping Bolt (8 used in this step) 4 4 Ø10 mm x 50 mm Wood Dowel (4 used in this step) H I 4 4 H 11. Align and attach one Upper Cross Assembly (I) to one Upper Cap Rail (H) using two Wood Dowels () and four 48 mm Bolts (4) as shown. Securely tighten the bolts with the enclosed L-shaped Allen wrench. 12. Repeat last step to combine the remaining Upper Cap Rail (H) and Upper Cross Assembly (I) together. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 12 Factory No
13 ASSMBLING UPPR HADBOARD/FOOTBOARD 3 F I G I Ø10 mm x 50 mm Wood Dowel (12 used in this step) Ø.5 mm x 100 mm Tapping Bolt (8 used in this step) Insert six Wood Dowels () into the end holes of the Upper Cross Assembly with warning label (I). Attach Upper Posts ( and F) to the Upper Cross Assembly by using four 100 mm Bolts (3) as shown. Tighten the bolts with the enclosed Allen wrench. 14. Repeat last step to attach Upper Posts ( and G) to the other Upper Cross Assembly (I). Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 13 Factory No
14 ASSMBLING UPPR HADBOARD/FOOTBOARD F I V 9 9 V G I V 9 9 V Ø4 mm x 0 mm Screw (4 used in this step) Align and attach one Removable Decor (V) to each Upper Post (, F and G) with one 0 mm Wood Screw (9) as shown. Make sure that the curved edge of Removable Decor (V) will face the floor when the unit is turned upright. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 14 Factory No
15 ASSMBLING UPPR BUNK 1 M 5 M Ø10 mm x 50 mm Wood Dowel (4 used in this step) 1 F G 5 J L Barrel Nut (12 used in this step) M M J I G F I L Ø1/4 x 110 mm Bolt (12 used in this step) 1 1. Insert the Wood Dowels () into the drilled large holes of Long Guardrail (M) at both ends. Attach 2 Long Guardrails (M) and the other Mattress Side Rail (J) between the Upper Posts ( and F) using eight 110 mm Bolts (1) and eight Barrel Nuts (5) as shown above. Make sure the wood stoppers for slat attached on side rail are up and face inward. 17. Attach Upper Ladder Side Rail (L) between the Upper Posts ( and G) using four 110 mm Bolts (1) and four Barrel Nuts (5). Make sure the wood stoppers for slat attached on side rail are up and face inward. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 15 Factory No
16 ASSMBLING UPPR BUNK Barrel Nut (4 used in this step) 5 T N N L G T T L L N 2 1 T 5 Ø1/4 x 38 mm Bolt (2 used in this step) 2 Ø1/4 x 110 mm Bolt (4 used in this step) 1 Ø10 mm x 50 mm Wood Dowel (4 used in this step) 18. Insert the Wood Dowels () into the end large holes of Short Guardrails (N) as a guide. Attach 2 Short Guardrails (N) between the Front Upper Post () and Front Guardrail Post (T) using four 110 mm Bolts (1) and four Barrel Nuts (5). As shown. 19. Fasten the Front Guardrail Post (T) to the Upper Ladder Side Rail (L) with two 38 mm Bolts (2), using the enclosed Allen wrench. As shown. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 1 Factory No
17 ASSMBLING UPPR BUNK 7 U UP M M J N N L UP U 7 Ø4 mm x 30 mm Screw ( used in this step) With the pilot holes as a guide, align and attach one Guardrail Support (U) to the center of the Long Guardrails (M) and the Upper Mattress Side Rail (J) by using three 30 mm Screws (7) through the countersunk holes and screw into place. As shown above. 21. Repeat the same procedure to attach the other Guardrail Support (U) to the Short Guardrails (N) and the Upper Ladder Side Rail (L). Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 17 Factory No
18 ASSMBLY OF TH BUNK BD F 10 G 10 D 10 D 10 Bed Connector Pin (4 used in this step) Now, place the two assembled bunks where you want to place your Bunk Bed. 23. Insert 4 Bed Connector Pins (10) into the top holes of Lower Bunk, as shown. 24. Now, ask for assistance to stack the Upper Bunk onto the Bed Connector Pins (10) on the Lower Bunk. NOT: Make sure that the Upper Bunk sits completely on top of the Lower Bunk and the pins go all the way, not leaving any gaps. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 18 Factory No
19 ASSMBLY OF TH LADDR S 4 S R 4 4 Q S 4 Ø.5 mm x 48 mm Tapping Bolt (8 used in this step) 4 Ø10 mm x 50 mm Wood Dowel (8 used in this step) 25. Insert the Wood Dowels () into the drilled large holes of Ladder Steps (S) at both ends. Attach Left and Right Ladder Supports (Q and R) to the Ladder Steps (S) using the 48 mm Tapping Bolts (4). Securely tighten all bolts with the enclosed Allen wrench. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 19 Factory No
20 ASSMBLY OF TH LADDR Q R L 2 L Q R K Q R K Ø1/4 x 38 mm Bolt (4 used in this step) Align and attach the assembled Ladder to the Ladder Side Rails (K and L) by inserting four 38 mm Bolts (2) through the pre-drilled holes on the Ladder Side Rails and screw into the threaded inserts on the Ladder Supports (Q and R). As shown. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 20 Factory No
21 ASSMBLY OF TH BUNK BD Ø4 mm x 30 mm Screw (14 used in this step) Lay out the Upper Mattress Support Slats (P) between the wood stoppers on the Upper Mattress Side Rail (J) and the Upper Ladder Side Rail (L). As shown. Insert and screw 30 mm Screws (7) into the countersunk holes in each end of the slats. Tighten the screws using a Phillips screwdriver. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 21 Factory No
22 ASSMBLY OF TH BUNK BD Ø1/4 x 38 mm Bolt (3 used in this step) 2 Ø4 mm x 30 mm Screw (14 used in this step) Align and attach 3 Slat Supports (W) to the bottom side of the Lower Mattress Support Slats (O) by inserting the 38 mm Bolts (2) through the countersunk holes on the Slats and screw into place as shown. 29. Lay out the Lower Mattress Support Slats (O) between the wood stoppers on the Mattress Side Rail (J) and Lower Ladder Side Rail (K). As shown. Insert and screw the 30 mm Screws (7) into the countersunk holes in each end of the slats. Tighten the screws using a Phillips screwdriver. Set the preattached Floor Lever underneath the Slat Supports (W) to the correct height. Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 22 Factory No
23 DISASSMBLING TH BUNK BD NOT: The Bunk Bed can be separated into a Twin Bed and a Full Size Bed. In this case, attach four Floor Protectors (8) onto the bottom of the Upper Posts (, F and G) Guardrails are not necessary. 30. To convert the bunk bed back into a Twin bed and a Full size bed, first unscrew the bolts to remove the Ladder and all Guardrails. 31. Have an assistant help to remove the Upper Bunk from the Lower Bunk. 32. Attach four Floor Protectors (8) to the bottom of the Upper Posts (, F and G), as shown in the illustration. The beds can now be placed in the desired locations. F G A F G B B 8 A Floor Protector (4 used in this step) 8 Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 23 Factory No
24 Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture. Check bolts/screws periodically and tighten them if necessary. Further advice about wood furniture care It is best to keep your furniture in a climate-controlled environment. xtreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages. We hope you enjoy your purchase for many years. Thank you for your purchasing! Please call for replacement parts or assistance: Whalen Furniture Manufacturing Page 24 Factory No
25 IF YOU ND TO ORDR RPLACMNT PARTS, PLAS US TH LIST BLOW Whitman Twin over Full Bunk Bed (WHMTFBB) *WHMTFBB-1-UP Upper Post *WHMTFBB-20-FGP Front Guardrail Post *WHMTFBB-2-UPF Upper Post F *WHMTFBB-21-RD Removable Decor *WHMTFBB-3-UPG Upper Post G *WHMTFBB-22-WFB Wood Filler Block *WHMTFBB-4-LPA Lower Post A *WHMTFBB-23-LS Ladder Step *WHMTFBB-5-LPB Lower Post B *WHMTFBB-24-LLS Left Ladder Support *WHMTFBB--UCR Upper Cap Rail *WHMTFBB-25-RLS Right Ladder Support *WHMTFBB-7-LCR Lower Cap Rail *WHMTFBB-2-110B Ø1/4 x 110 mm Bolt *WHMTFBB-8-UCA Upper Cross Assembly *WHMTFBB-27-38B Ø1/4 x 38 mm Bolt *WHMTFBB-9-LCA Lower Cross Assembly *WHMTFBB-28-48B Ø.5 mm x 48 mm Bolt *WHMTFBB-10-SS Slat Support *WHMTFBB B Ø.5 mm x 100 mm Bolt *WHMTFBB-11-FL Floor Lever *WHMTFBB-30-30S Ø4 mm x 30 mm Screw *WHMTFBB-12-SG Short Guardrail *WHMTFBB-31-0S Ø4 mm x 0 mm Screw *WHMTFBB-13-LG Long Guardrail *WHMTFBB-32-FP Floor Protector *WHMTFBB-14-LLSR Lower Ladder Side Rail *WHMTFBB-33-M10x50WD Ø10 mm x 50 mm Wood Dowel *WHMTFBB-15-ULSR Upper Ladder Side Rail *WHMTFBB-34-BCP Bed Connector Pin *WHMTFBB-1-MSR Mattress Side Rail *WHMTFBB-35-BN Ø1/4 Barrel Nut *WHMTFBB-17-UMSS Upper Mattress Support Slats *WHMTFBB-3-THAW T-Handle Allen Wrench *WHMTFBB-18-LMSS Lower Mattress Support Slats *WHMTFBB-37-LAW L-shaped Allen Wrench *WHMTFBB-19-GS Guardrail Support *WHMTFBB-CH Complete Hardware
Whalen Furniture Mfg. Inc. Factory No. 43-11696 Page # 1
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale
More informationBrookland Trunk/Coffee Table Stock # BROTCT
LOT NUMBER: DATE PURCHASED: / / Brookland Trunk/Coffee Table Stock # BROTCT ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
More informationBUNK BED. Model No.: DA3797E - Espresso DA3797P- Pine. UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: Lot number: Date of purchase:
BUNK BED Model No.: DA3797E - Espresso DA3797P- Pine UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
More informationpottery barn kids MADELINE BUNK BED
pottery barn kids MADELINE BUNK BED! WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To help prevent serious or fatal injuries from entrapment
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationHow To Make A Thomas Bunk Bed
pottery barn kids THOMAS BUNK BED WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS
More informationItem #: BTOL Assembly Instructions
Item #: BTOL Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE
More informationConvertible Crib and Changer (M668)
Model No.: M668 PO #: Serial #: Convertible Crib and Changer (M668) THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. If you have any questions or missing parts, please contact us. DO NOT
More informationSamuel Shorty Bunk Bed
Samuel Shorty unk ed - Please keep for future reference / 88/999 0/8 IMPORTANT NOTE: The top surface of the mattress should not come above this line. imensions Width - 8cm epth - 8cm eight - 0cm IMPORTANT
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationAssembly and Usage Instructions
Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationATLANTA 90CM HIGH BEDSTEAD
ATLANTA 90CM HIGH BEDSTEAD Stock number: 480X-52 Thank you for purchasing this product. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Pre-assembly
More informationCK548000TX. Amherst Cocktail Table Trunk. Assembly Instructions PO#: Page 1
CK548000TX Amherst Cocktail Table Trunk Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service: 1-800-633-5096 service@seidal.com www.seidal.com PO#: Page
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More information1 Door Tall Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Tall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationTriple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE
NG0M Triple Threat 3-in- Game Table 3 IN GAME TABLE Thank 3 in Y Game Table Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain
More informationReachout Lock Replacement for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors
for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors Thank you for choosing Andersen. For questions call 1-888-888-7020. For more information
More informationSAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #6100 INPOOL LADDER 42" TO 54" ASSEMBLY AND INSTRUCTION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #6100 INPOOL LADDER 42" TO 54" ASSEMBLY AND INSTRUCTION MANUAL The Anti-Entrapment Barrier is included in this ladder for the U.S. and
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationHOME GYM. Model. Retain This Manual for Reference OWNER'S MANUAL. www.hyper-extension.com
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice www.hyper-extension.com HOME GYM 50036 Hardware Identifier Assembly Instruction Parts List Warranty
More informationEasy Assembly Instructions & Rules
Model #64-2000 Easy Assembly Instructions & Rules 4-in-1 Casino Table DO NOT RETURN TO STORE. FOR ALL RETURNS AND WARRANTY COVERAGE PLEASE CALL GLD PRODUCTS: 1-800-225-7593 Please provide model number,
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationDOREL ASIA 3-PC COUNTER HEIGHT BAR SET. Model No: DA3729 UPC CODE: 0-65857-16286-8 NOTE: / /
DOREL ASIA PC COUTER HEIGHT BAR SET Model o: DA9 UPC CODE: 058588 OTE: THIS ISTRUCTIO BOOKLET COTAIS IMPORTAT SAFETY IFORMATIO. PLEASE READ AD KEEP FOR FUTURE REFERECE. Lot number: (TAKE FROM CARTO) Date
More informationSliding Door Hardware Installation Instructions
Sliding Door Hardware Installation Instructions Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview ff All Krown Lab sliding
More informationTrundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds)
Bunk Beds Unlimited Trundle Bed Plans (For Use Under Twin or Full-Size Standard Length Beds) On the following pages we have included all of the necessary drawings and requirements for a Modified twin-size
More informationTHE CRACKER BARREL OLD COUNTRY STORE ROCKING CHAIR ASSEMBLY INSTRUCTIONS
THE CRACKER BARREL OLD COUNTRY STORE ROCKING CHAIR ASSEMBLY INSTRUCTIONS Manufacturer of Solid Hardwood Rocking Chairs Since 1834 Thank you for purchasing a quality rocking chair from Cracker Barrel Old
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationGreenWay Solar LED Path and Trail Lighting System. Installation and Owner s Manual
GreenWay Solar LED Path and Trail Lighting System Installation and Owner s Manual Important Notes and Warnings This installation and instruction manual provides installation, operation, and maintenance
More informationATS Overhead Table Shelf System INSTRUCTION MANUAL
ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship
More informationAssembly Instructions
CK622400TX- Espresso CK612400TX- Black Nailhead Cocktail Table Trunk Assembly Instructions For assistance with assembly contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com
More informationBeadboard Wall Bookcase
Beadboard Wall Bookcase Note: The maximum load for each shelf is 30lbs.This hanging system is meant for drywall/wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
More informationCombination Unit 5'6" Windows a i o P t
for Andersen 5'6" Double-Hung Venting s Windows a i o P t o rs D o Congratulations You have just purchased one of the many fine Andersen products. For ease of assembly and installation and continued enjoyment
More informationActive and Passive Sash Replacement
for Andersen Gliding Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete the procedure, call Andersen at 1-888-888-7020 for
More informationMODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER
MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.
More informationSliding Barn Door Hardware Installation Instructions BALDUR and ODEN
Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview
More informationVISION SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS
VISION SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationCirco Kids. >> assembly instructions 92345 F. 3 Drawer Dresser. DPCI # 249-20 - 0201 (White) DPCI # 249-20 - 0211 (Chocolate)
Circo Kids 3 Drawer Dresser DPCI # 249-20 - 0201 (White) DPCI # 249-20 - 0211 (Chocolate) >> assembly instructions 92345 F 1 FREE! Do not go back to your store! we will help you! Missing or Damage parts?
More informationStandard Sleep Pod Side Entry Assembly Instructions
Standard Sleep Pod Side Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod Pod assembly onsite is a relatively simple exercise for two people
More informationDIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS
DIRECTIONS FOR ASSEMBLING BASE & WALL CABINETS TheRTAStore.com STEP 1: CLEAR A WORK SPACE Place your RTA cabinet panels on a smooth, scratch resistant surface in a large, open area. (Some people like to
More informationOwner s Guide and Installation Manual. Vancouver Model Name. 21321, 21328 Model No. English Español
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Vancouver Model Name 21321, 21328 Model No. Type A Models Owner s Guide and Installation
More informationDell P Series Monitor VESA Mounting Bracket Installation Instructions
Dell P Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell P Series Monitor and the Dell E24 Monitor. The cloud
More informationUnpacking, Installation, and Customization
Unpacking, Installation, and Customization NetShelter WX Enclosure AR100 AR100HD Contents Unpacking... 1 How to Unpack the Enclosure............................... 1 Please Recycle..........................................
More informationENIGMA-X SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS
ENIGMA-X SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationKITCHENS. Tip PAGE 1 FITTING YOUR KITCHEN GUIDE. How to mark out a kitchen. Tools required for installing a kitchen STEP ONE STEP TWO STEP THREE
FITTING YOUR KITCHEN GUIDE How to mark out a kitchen PAGE 1 Before starting on the installation, measure 870mm from the lowest point of the floor and mark a datum line around the room to indicate where
More informationMake yourself comfortable with Staples brand furniture.
Make yourself comfortable with Staples brand furniture. Check us out online and in store for more great ways to add some easy to your day. black glass desk instructions 2 (30ST) Staples BLACK GLASS DSK
More informationUPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video
UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video http://bit.ly/9ywwh! CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL
More informationBeautifully Traditional
Arcade 800mm Single Sliding Door Quadrant - nickel Arcade 900mm Single Sliding Door Quadrant - nickel ARC48 ARC49 INSTALLATION INSTRUCTIONS A www.arcadebathrooms.com IMPORTANT - Please read before installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Video Conference Shelf for Low Profile Flat-Panel Mounts NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888
More informationCAR SEAT/ STROLLER INSTRUCTION MANUAL
CAR SEAT/ STROLLER INSTRUCTION MANUAL English PM-0624AB 3/98 Do not use this 4-in-1 System until you read and understand these instructions! IMPORTANT INFORMATION Thank you for selecting this 4-in-1 System
More informationCombination Unit (shown from interior) WARNING
for Andersen Double-Hung Venting s Windows a i o P t o rs D o Congratulations You have just purchased one of the many fine Andersen products. For ease of assembly and installation and continued enjoyment
More informationIn-Ground Basketball System Owners Manual
In-Ground Basketball System Owners Manual Customer Service Center N53 W4700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: WARNING! 3 Capable Adults REQUIRED TOOLS AND
More informationDIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
More informationInstallation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step
More informationImportant Information
Single Door Quadrant Instruction Manual ESQ Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to
More informationESTATE WAGON MODEL 300 OWNER MANUAL
ESTATE WAGON MODEL 300 OWNER MANUAL Country Manufacturing, Inc. P.O. Box 104 Fredericktown, OH 43019 PH: 740-694-9926 FAX: 740-694-5088 I. INTRODUCTION The Model 300 Four Wheeled Wagon (ESTATE VERSATILITY
More informationArticulating TV Wall Mount for 19" to 70" Flat Panel TVs
THIS INSTRUCTION BOOKLET CONTINS IMPORTNT SETY INORMTION. PLESE RED ND KEEP OR UTURE REERENCE. Lot Number: Date: rticulating TV Wall Mount for 19" to 7" lat Panel TVs Model No: DCD1319 Option 1 Option
More informationA701 (6904-002018 <01>)
A70 () Wood Stud mm (7/6 in.).4 mm (3/3 in.) 6 mm (5/64 in.) 3 mm (/8 in.) Sanus Hwy 36 West Saint Paul, MN 553 USA Customer Service Americas: 800-359-550 65-484-7988 info@sanus.com Europe, Middle East,
More informationSAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7200
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7200 ROLLGUARD A-FRAME LADDER LADDER MUST BE ATTACHED TO POOL FRAME. DO NOT USE WITH INFLATABLE POOLS ASSEMBLY AND INSTALLATION MANUAL
More informationAssembly Instructions Model 1544 Heart-Of-The-Kitchen Island
Assembly Instructions Model 1544 Heart-Of-The-Kitchen Island A. These units are Ready-to-Assemble. Catskill uses positive fastening methods such as wood screws and in some places hidden Bastion fasteners.
More informationRear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
More informationHOW TO INSTALL A BEAUTIFUL NEW KITCHEN
HOW TO INSTALL A BEAUTIFUL NEW KITCHEN Easy to follow step-by-step kitchen cabinet installation TOOL AND MATERIAL LIST Hammer Pry bar Screwdriver Phillips Flathead Level Tape measure Pencil Straight edge
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationInstallation Instructions:
Portable Guardrail System Model Numbers: 7900060, 7900061, 7900062, 7900063 Installation Instructions: Portable Guardrail System This instruction is intended to meet the Manufacturer s Instructions requirement
More informationStainless Steel Sink Work Center With Portable Sink, Colander and Cutting Board
SKU: 463780 / QK09 Owner s Manual Stainless Steel Sink Work Center With Portable Sink, Colander and Cutting Board THANK YOU for selecting American Standard the benchmark of fine quality for over 00 years.
More informationWATERBED ASSEMBLY INSTRUCTIONS
WATERBED ASSEMBLY INSTRUCTIONS WARNING: Never leave any infant, or handicapped child who cannot turn over, unattended on this or any other adult mattress. Infant or handicapped children can suffocate in
More informationINSTALLATION INSTRUCTIONS BL-8704
INSTALLATION INSTRUCTIONS BL-8704 EXPOSED BLACK LEVER THERMOSTATIC MIXING VALVE WITH RISER KIT, HANDSET, LEVER DIVERTER, 8 ROSE AND ADJUSTABLE RISER PIPE BRACKET. Dimensions in Inches (& Millimetres) 1
More informationWall-Mounting your HP computer. User Guide
Wall-Mounting your HP computer User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should
More informationStructural Holding System
Structural Holding System Users Manual November 2013 by Vehicle Service Group. All rights reserved. CO8812.1 502071 Rev. - 11/21/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies
More informationCRASH RAIL INSTALLATION HEIGHT
PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS. CONTAINED
More informationHOME GYM ADI-10250-I. Model ADI-10250-I. Retain This Manual for Reference OWNER'S MANUAL
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice HOME GYM ADI-10250-I Important Assembly Information Care and Maintenance Parts List Warranty Ordering
More informationAZEK Rail Install Guide
TRIM MOULDING DECK PORCH RAIL PAVERS AZEK Rail Install Guide Installing AZEK Rail with CableRail by Feeney... 1 Installing CableRail by Feeney for AZEK Rail... 7 Installing AZEK Rail Stairs with CableRail
More informationPOLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS
POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing
More information10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY
10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY Instruction Manual ITM./ART.496840 VIEW ASSEMBLY VIDEO AND INSTRUCTION MANUAL AT www.zhengteusa.com Before assembly, read these instructions carefully.
More informationINSTALLATION INSTRUCTIONS MK-8704
INSTALLATION INSTRUCTIONS MK-8704 EXPOSED MACKINTOSH THERMOSTATIC MIXING VALVE WITH RISER KIT, HANDSET, LEVER DIVERTER, 8 ROSE AND ADJUSTABLE RISER PIPE BRACKET. Dimensions in Inches (& Millimetres) 1
More informationTABLE OF CONTENTS CABINET SAFETY
CABINET SAFETY...2 ASSEMBLY INSTRUCTIONS...3 Tools and Parts...3 Cabinet Use Requirements...3 Unpack the Cabinet...3 TABLE OF CONTENTS CABINET SAFETY Install the Bumper...3 Install the Casters...4 Install
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationChapter 10 - Scaffolding Systems
Chapter 10 - Scaffolding Systems Contents Chapter 10 - Scaffolding Systems... 10-1 Check and Oil the Pump Jacks... 10-4 Set Pump Jack Brackets... Error! Bookmark not defined. Set Pump Jack Poles... 10-5
More informationOAK WORKBENCH WITH 2 DRAWERS
OAK WORKBENCH WITH 2 DRAWERS Model 93991 ASSEMBLY Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
More informationHow to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
More informationIMPORTANT INFORMATION
Curved Quadrant Instruction Manual CQ IMPORTANT INFORMATION Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines.
More informationChildren s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
More information3/4 PIPE CLAMP WITH STAND
3/4 PIPE CLAMP WITH STAND Model 94053 ASSEMBLY AND OPERATING INSTRUCTIONS (3/4 DIAMETER PIPE NOT INCLUDED.) 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com
More informationSeismic Installation for Attic Storage System
Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener
More informationCORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS
CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS D E F Y I N G C O N V E N T I O N Congratulations on your new Corner Fridge Your new corner fridge may have different functions
More informationTOLL FREE: (866) 591-7792. E-Mail: techmail@vigoindustries.com. www.vigoindustries.com VANITY SPECIFICATIONS. VANITY COMPONENTS Model VG09042K1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09042K1 MODEL VG09042K1 FEATURES Freestanding cabinet Soft closing sliding cabinet drawer hardware White, single hole ceramic sink Cabinet ships assembled
More informationIN00419 (rev A) Aqua 6 Glide Quadrant and Off-set Quadrant Enclosure
IN00419 (rev A) Aqua 6 Glide Quadrant and Off-set Quadrant Enclosure Instruction suitable for both Quadrant & Off-set Quadrant variations. Instruction suitable for both Right and Left Hand fixing variations
More information4-in-1 SWIVEL TABLE. 54in (1.37m) CONTACT INFO Hours. Technical Support Monday to Friday (9:00am to 5pm EST) WARNING:
54in (1.37m) 4-in-1 SWIVEL TABLE CAUTINotOrecommended N: ELECTRI CALLY OPERATED PRODUCT for children under 8 years of age. As with all electric products, precautions should be observed during handling
More information758 Heavy-duty Ratchet Guy Wire Cutter
INSTRUCTION MANUAL 758 Heavy-duty Ratchet Guy Wire Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationINSTRUCTION BOOK FOR. Single Monitor Video Conference Cart
INSTRUCTION BOOK FOR Single Monitor Video Conference Cart Procedure 1. Remove contents from cartons and examine for damaged or missing parts. The keys for the cabinet doors are tied to the outside of the
More information7 Watt Solar Charger Solar Panel
7 Watt Solar Charger Solar Panel Owner s Manual Warning: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationILLUSION FRAMELESS SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
PREPARATION Approximate Installation Time: Tools Required for Installation: 60 minutes Hacksaw Electric Drill 3/16 Masonry Bit Pencil/Felt tip pen Safety Glasses Measuring Tape Masking Tape Standard Screw
More information