Reference Document P/N , Rev. BB December Micro Motion PED Tagging Information
|
|
|
- Daniela Wilkerson
- 7 years ago
- Views:
Transcription
1 Reference Document P/N , Rev. BB December 2012 Micro Motion PED Tagging Information
2 This reference document covers information tagged on Micro Motion meters that comply with the Pressure Equipment Directive. PED Certificate Holder Temperature Ratings Micro Motion Inc., Boulder, CO Refer to ATEX Installation Manual at PED Notified Body Number 0036 Fluid Group I Sensor model CMF200A312 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; EN Form D 28.5 CMF200A316 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; EN Form D 28.5 CMF200A341 *** (N, V, Z or 6) **** 1½-inch ANSI CL150 weld neck raised face flange 8.4 CMF200A342 *** (N, V, Z or 6) **** 1½-inch ANSI CL300 weld neck raised face flange 30.3 CMF200A343 *** (N, V, Z or 6) **** 1½-inch ANSI CL600 weld neck raised face flange 60.7 CMF200A363 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; EN Form B CMF200A365 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; EN Form B CMF200A366 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; EN Form D 71.4 CMF200A367 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; EN Form D 71.4 CMF200A368 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; EN Form B CMF200A369 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; EN Form B CMF200A377 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF200A378 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF200A379 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF200A380 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF200A381 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF200A382 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF200A383 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF200A384 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF200A418 *** (N, V, Z or 6) **** 2-inch ANSI CL150 weld neck raised face flange 8.4 CMF200A419 *** (N, V, Z or 6) **** 2-inch ANSI CL300 weld neck raised face flange 30.3 CMF200A420 *** (N, V, Z or 6) **** 2-inch ANSI CL600 weld neck raised face flange 60.7 CMF200B540 *** (N, V, Z or 6) **** 1½-inch ANSI CL150 lap joint flange , Micro Motion, Inc. All rights reserved. ELITE and ProLink are registered trademarks, and MVD and MVD Direct Connect are trademarks of Micro Motion, Inc., Boulder, Colorado. Micro Motion is a registered trade name of Micro Motion, Inc., Boulder, Colorado. The Micro Motion and Emerson logos are trademarks and service marks of Emerson Electric Co. All other trademarks are property of their respective owners.
3 CMF200B541 *** (N, V, Z or 6) **** 1½-inch ANSI CL300 lap joint flange 29.5 CMF200B543 *** (N, V, Z or 6) **** DN40 PN40 lap joint flange; DIN 2656 type C face 23.0 CMF200B544 *** (N, V, Z or 6) **** 2-inch ANSI CL150 lap joint flange 8.4 CMF200B545 *** (N, V, Z or 6) **** 2-inch ANSI CL300 lap joint flange 29.5 CMF200B547 *** (N, V, Z or 6) **** DN50 PN40 lap joint flange; DIN 2656 type C face 23.0 CMF200B548 *** (N, V, Z or 6) **** DN40 PN40 lap joint flange; EN Form B CMF200B549 *** (N, V, Z or 6) **** DN50 PN40 lap joint flange; EN Form B CMF200H540 *** (N, V, Z or 6) **** 1½-inch ANSI CL150 lap joint flange 13.1 CMF200H541 *** (N, V, Z or 6) **** 1½-inch ANSI CL300 lap joint flange 34.1 CMF200H543 *** (N, V, Z or 6) **** DN40 PN40 lap joint flange; DIN 2656 type C face 27.8 CMF200H544 *** (N, V, Z or 6) **** 2-inch ANSI CL150 lap joint flange 13.1 CMF200H545 *** (N, V, Z or 6) **** 2-inch ANSI CL300 lap joint flange 34.1 CMF200H547 *** (N, V, Z or 6) **** DN50 PN40 lap joint flange; DIN 2656 type C face 27.8 CMF200H548 *** (N, V, Z or 6) **** DN40 PN40 lap joint flange; EN Form B CMF200H549 *** (N, V, Z or 6) **** DN50 PN40 lap joint flange; EN Form B CMF200L441 *** (N, V, Z or 6) **** 1½-inch ANSI CL150 weld neck raised face flange 13.1 CMF200L442 *** (N, V, Z or 6) **** 1½-inch ANSI CL300 weld neck raised face flange 34.1 CMF200L457 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; EN Form B CMF200L458 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; EN Form B CMF200L481 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; DIN 2526 type C face 27.8 CMF200L482 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; DIN 2526 type C face 27.8 CMF200L518 *** (N, V, Z or 6) **** 2-inch ANSI CL150 weld neck raised face flange 13.1 CMF200L519 *** (N, V, Z or 6) **** 2-inch ANSI CL300 weld neck raised face flange 34.1 CMF200M312 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; EN Form D 33.5 CMF200M316 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; EN Form D 33.5 CMF200M341 *** (N, V, Z or 6) **** 1½-inch ANSI CL150 weld neck raised face flange 13.6 CMF200M342 *** (N, V, Z or 6) **** 1½-inch ANSI CL300 weld neck raised face flange 35.5 CMF200M343 *** (N, V, Z or 6) **** 1½-inch ANSI CL600 weld neck raised face flange 70.9 CMF200M351 *** (N, V, Z or 6) **** 1½-inch sanitary fitting (Tri-Clamp compatible) 64.5
4 CMF200M352 *** (N, V, Z or 6) **** 2-inch sanitary fitting (Tri-Clamp compatible) 64.5 CMF200M363 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; EN Form B CMF200M365 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; EN Form B CMF200M366 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; EN Form D 83.8 CMF200M367 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; EN Form D 83.8 CMF200M368 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; EN Form B CMF200M369 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; EN Form B CMF200M377 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; DIN 2637 type E face CMF200M378 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; DIN 2637 type E face CMF200M379 *** (N, V, Z or 6) **** DN40 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF200M380 *** (N, V, Z or 6) **** DN50 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF200M381 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF200M382 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF200M383 *** (N, V, Z or 6) **** DN40 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF200M384 *** (N, V, Z or 6) **** DN50 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF200M418 *** (N, V, Z or 6) **** 2-inch ANSI CL150 weld neck raised face flange 13.6 CMF200M419 *** (N, V, Z or 6) **** 2-inch ANSI CL300 weld neck raised face flange 35.5 CMF200M420 *** (N, V, Z or 6) **** 2-inch ANSI CL600 weld neck raised face flange 70.9 CMF300A326 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; EN Form B CMF300A333 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form D 28.5 CMF300A355 *** (N, V, Z or 6) **** 3-inch ANSI CL150 weld neck raised face flange 8.4 CMF300A356 *** (N, V, Z or 6) **** 3-inch ANSI CL300 weld neck raised face flange 30.3 CMF300A357 *** (N, V, Z or 6) **** 3-inch ANSI CL600 weld neck raised face flange 60.7 CMF300A358 *** (N, V, Z or 6) **** 3-inch ANSI CL900 weld neck raised face flange 91.0 CMF300A359 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form D 71.4 CMF300A371 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; EN Form B CMF300A372 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF300A373 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; EN Form B CMF300A374 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B2 71.4
5 CMF300A375 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; EN Form D 71.4 CMF300A391 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF300A392 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF300A393 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF300A394 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF300A395 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF300A396 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF300A397 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF300A398 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF300A425 *** (N, V, Z or 6) **** 4-inch ANSI CL150 weld neck raised face flange 8.4 CMF300A426 *** (N, V, Z or 6) **** 4-inch ANSI CL300 weld neck raised face flange 30.3 CMF300A427 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 60.7 CMF300A428 *** (N, V, Z or 6) **** 4-inch ANSI CL900 weld neck raised face flange 91.0 CMF300B550 *** (N, V, Z or 6) **** 3-inch ANSI CL150 lap joint flange 8.4 CMF300B551 *** (N, V, Z or 6) **** 3-inch ANSI CL300 lap joint flange 29.5 CMF300B553 *** (N, V, Z or 6) **** DN80 PN40 lap joint flange; DIN 2656 type C face 23.0 CMF300B554 *** (N, V, Z or 6) **** DN80 PN40 lap joint flange; EN Form B CMF300H550 *** (N, V, Z or 6) **** 3-inch ANSI CL150 lap joint flange 13.1 CMF300H551 *** (N, V, Z or 6) **** 3-inch ANSI CL300 lap joint flange 34.1 CMF300H553 *** (N, V, Z or 6) **** DN80 PN40 lap joint flange; DIN 2656 type C face 27.8 CMF300H554 *** (N, V, Z or 6) **** DN80 PN40 lap joint flange; EN Form B CMF300L455 *** (N, V, Z or 6) **** 3-inch ANSI CL150 weld neck raised face flange 13.1 CMF300L456 *** (N, V, Z or 6) **** 3-inch ANSI CL300 weld neck raised face flange 34.1 CMF300L459 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; EN Form B CMF300L491 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; DIN 2526 type C face 27.8 CMF300M326 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; EN Form D 33.5 CMF300M333 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form D 33.5 CMF300M355 *** (N, V, Z or 6) **** 3-inch ANSI CL150 weld neck raised face flange 13.6 CMF300M356 *** (N, V, Z or 6) **** 3-inch ANSI CL300 weld neck raised face flange 35.5
6 CMF300M357 *** (N, V, Z or 6) **** 3-inch ANSI CL600 weld neck raised face flange 70.9 CMF300M359 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form D 83.8 CMF300M361 *** (N, V, Z or 6) **** 3-inch sanitary fitting (Tri-Clamp compatible) 64.5 CMF300M371 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; EN Form B CMF300M372 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF300M373 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; EN Form B CMF300M374 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF300M375 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange EN Form D 83.8 CMF300M391 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF300M392 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF300M393 *** (N, V, Z or 6) **** DN80 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF300M394 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF300M395 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; DIN 2637 type E face 83.8 CMF300M396 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type E face 83.8 CMF300M397 *** (N, V, Z or 6) **** DN80 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF300M398 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF300M425 *** (N, V, Z or 6) **** 4-inch ANSI CL150 weld neck raised face flange 13.6 CMF300M426 *** (N, V, Z or 6) **** 4-inch ANSI CL300 weld neck raised face flange 35.5 CMF300M427 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 70.9 CMF400A435 *** (N, V, Z or 6) **** 4-inch ANSI CL150 weld neck raised face flange 8.4 CMF400A436 *** (N, V, Z or 6) **** 4-inch ANSI CL300 weld neck raised face flange 30.3 CMF400A437 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 60.7 CMF400A438 *** (N, V, Z or 6) **** 4-inch ANSI CL900 weld neck raised face flange 85.5 CMF400A443 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF400A444 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form B CMF400A445 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF400A446 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMF400A447 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form D 71.4 CMF400A448 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form D 71.4
7 CMF400A451 *** (N, V, Z or 6) **** 6-inch ANSI CL150 weld neck raised face flange 8.4 CMF400A452 *** (N, V, Z or 6) **** 6-inch ANSI CL300 weld neck raised face flange 30.3 CMF400A453 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 60.7 CMF400A460 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF400A461 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; DIN 2635 type C face 28.5 CMF400A462 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF400A463 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; DIN 2635 type N grooved face 28.5 CMF400A464 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF400A465 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; DIN 2637 type E face 71.4 CMF400A466 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF400A467 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; DIN 2637 type N grooved face 71.4 CMF400A478 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form D 28.5 CMF400A480 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form D 28.5 CMF400B906 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF400B907 *** (N, V, Z or 6) **** 4-inch ANSI CL150 lap joint flange 8.4 CMF400B908 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF400B910 *** (N, V, Z or 6) **** DN100 PN160 weld neck flange; EN Form B CMF400B911 *** (N, V, Z or 6) **** 4-inch ANSI CL150 lap joint flange 8.4 CMF400B912 *** (N, V, Z or 6) **** 4-inch ANSI CL300 lap joint flange 40.2 CMF400B913 *** (N, V, Z or 6) **** 4-inch ANSI CL600 lap joint flange 80.3 CMF400B914 *** (N, V, Z or 6) **** 4-inch ANSI CL900 lap joint flange CMF400H906 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF400H907 *** (N, V, Z or 6) **** 4-inch ANSI CL150 lap joint flange 13.1 CMF400H908 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF400H910 *** (N, V, Z or 6) **** DN100 PN160 weld neck flange; EN Form B CMF400H911 *** (N, V, Z or 6) **** 4-inch ANSI CL150 weld neck raised face flange 13.8 CMF400H912 *** (N, V, Z or 6) **** 4-inch ANSI CL300 weld neck raised face flange 48.3 CMF400H913 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 96.2 CMF400H914 *** (N, V, Z or 6) **** 4-inch ANSI CL900 weld neck raised face flange 144.5
8 CMF400M435 *** (N, V, Z or 6) **** 4-inch ANSI CL150 weld neck raised face flange 13.6 CMF400M436 *** (N, V, Z or 6) **** 4-inch ANSI CL300 weld neck raised face flange 35.5 CMF400M437 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 70.9 CMF400M443 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form B CMF400M444 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form B CMF400M445 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF400M446 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMF400M447 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form D 83.8 CMF400M448 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form D 83.8 CMF400M451 *** (N, V, Z or 6) **** 6-inch ANSI CL150 weld neck raised face flange 13.6 CMF400M452 *** (N, V, Z or 6) **** 6-inch ANSI CL300 weld neck raised face flange 35.5 CMF400M453 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 70.9 CMF400M460 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF400M461 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; DIN 2635 type C face 33.5 CMF400M462 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF400M463 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 CMF400M464 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type E face 83.8 CMF400M465 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; DIN 2637 type E face 83.8 CMF400M466 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF400M467 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 CMF400M478 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form D 33.5 CMF400M480 *** (N, V, Z or 6) **** DN100 PN40 weld neck flange; EN Form D 33.5 CMF400P437 *** (N, V, Z or 6) **** 4-inch ANSI CL600 weld neck raised face flange 70.9 CMF400P438 *** (N, V, Z or 6) **** 4-inch ANSI CL900 weld neck raised face flange CMF400P439 *** (N, V, Z or 6) **** 4-inch ANSI CL1500 weld neck raised face flange CMF400P445 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form B CMF400P446 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMF400P447 *** (N, V, Z or 6) **** DN100 PN100 weld neck flange; EN Form D 83.8 CMF400P448 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form D 83.8
9 CMF400P453 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 70.9 CMF400P468 *** (N, V, Z or 6) **** DN100 PN160 weld neck flange; EN Form B CMF400P562 *** (N, V, Z or 6) **** CMF400P563 *** (N, V, Z or 6) **** 4-inch ANSI CL600 carbon steel/316l stainless steel lap joint flange inch ANSI CL900 carbon steel/316l stainless steel lap joint flange CMFHC2A451 *** (N, V, Z or 6) **** 6-inch ANSI CL150 weld neck raised face flange 8.4 CMFHC2A452 *** (N, V, Z or 6) **** 6-inch ANSI CL300 weld neck raised face flange 30.3 CMFHC2A453 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 60.7 CMFHC2A801 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC2A802 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC2A803 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC2A810 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 8.4 CMFHC2A811 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 30.3 CMFHC2A818 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 60.7 CMFHC2A819 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange 84.3 CMFHC2A821 *** (N, V, Z or 6) **** 6-inch ANSI CL900 weld neck raised face flange 84.3 CMFHC2A822 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form B CMFHC2A823 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMFHC2A824 *** (N, V, Z or 6) **** DN150 PN160 weld neck flange; EN Form B CMFHC2M451 *** (N, V, Z or 6) **** 6-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC2M452 *** (N, V, Z or 6) **** 6-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC2M453 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC2M801 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC2M802 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC2M803 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC2M810 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC2M811 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC2M818 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC2M819 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange 98.5
10 CMFHC2M821 *** (N, V, Z or 6) **** 6-inch ANSI CL900 weld neck raised face flange 98.5 CMFHC2M822 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form B CMFHC2M823 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMFHC2M824 *** (N, V, Z or 6) **** DN150 PN160 weld neck flange; EN Form B CMFHC2Y956 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC2Y957 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC2Y958 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC2Y959 *** (N, V, Z or 6) **** DN150 PN40 weld neck flange; EN Form B CMFHC2Y960 *** (N, V, Z or 6) **** DN150 PN100 weld neck flange; EN Form B CMFHC2Y961 *** (N, V, Z or 6) **** DN150 PN160 weld neck flange; EN Form B CMFHC2Y962 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 14.0 CMFHC2Y963 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 42.7 CMFHC2Y964 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 85.4 CMFHC2Y965 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange CMFHC2Y966 *** (N, V, Z or 6) **** 6-inch ANSI CL150 weld neck raised face flange 14.0 CMFHC2Y967 *** (N, V, Z or 6) **** 6-inch ANSI CL300 weld neck raised face flange 42.7 CMFHC2Y968 *** (N, V, Z or 6) **** 6-inch ANSI CL600 weld neck raised face flange 85.4 CMFHC2Y969 *** (N, V, Z or 6) **** 6-inch ANSI CL900 weld neck raised face flange CMFHC3A801 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC3A802 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC3A803 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC3A804 *** (N, V, Z or 6) **** DN250 PN40 weld neck flange; EN Form B CMFHC3A805 *** (N, V, Z or 6) **** DN250 PN100 weld neck flange; EN Form B CMFHC3A806 *** (N, V, Z or 6) **** DN250 PN160 weld neck flange; EN Form B CMFHC3A810 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 8.4 CMFHC3A811 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 30.3 CMFHC3A812 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 75.1 CMFHC3A813 *** (N, V, Z or 6) **** 10-inch ANSI CL150 weld neck raised face flange 8.4 CMFHC3A814 *** (N, V, Z or 6) **** 10-inch ANSI CL300 weld neck raised face flange 30.3
11 CMFHC3A815 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 60.7 CMFHC3A816 *** (N, V, Z or 6) **** 10-inch ANSI CL600 lap joint flange 75.1 CMFHC3A817 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 60.7 CMFHC3A818 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 60.7 CMFHC3A819 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange 84.3 CMFHC3A820 *** (N, V, Z or 6) **** 10-inch ANSI CL900 weld neck raised face flange 84.3 CMFHC3M801 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC3M802 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC3M803 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC3M804 *** (N, V, Z or 6) **** DN250 PN40 weld neck flange; EN Form B CMFHC3M805 *** (N, V, Z or 6) **** DN250 PN100 weld neck flange; EN Form B CMFHC3M806 *** (N, V, Z or 6) **** DN250 PN160 weld neck flange; EN Form B CMFHC3M810 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC3M811 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC3M812 *** (N, V, Z or 6) **** 8-inch ANSI CL600 lap joint flange 87.2 CMFHC3M813 *** (N, V, Z or 6) **** 10-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC3M814 *** (N, V, Z or 6) **** 10-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC3M815 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC3M816 *** (N, V, Z or 6) **** 10-inch ANSI CL600 lap joint flange 87.2 CMFHC3M817 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC3M818 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC3M819 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange 98.5 CMFHC3M820 *** (N, V, Z or 6) **** 10-inch ANSI CL900 weld neck raised face flange 98.5 CMFHC3Y825 *** (N, V, Z or 6) **** DN200 PN40 weld neck flange; EN Form B CMFHC3Y826 *** (N, V, Z or 6) **** DN200 PN100 weld neck flange; EN Form B CMFHC3Y827 *** (N, V, Z or 6) **** DN200 PN160 weld neck flange; EN Form B CMFHC3Y828 *** (N, V, Z or 6) **** DN250 PN40 weld neck flange; EN Form B CMFHC3Y829 *** (N, V, Z or 6) **** DN250 PN100 weld neck flange; EN Form B CMFHC3Y830 *** (N, V, Z or 6) **** DN250 PN160 weld neck flange; EN Form B
12 CMFHC3Y831 *** (N, V, Z or 6) **** 8-inch ANSI CL150 weld neck raised face flange 14.0 CMFHC3Y832 *** (N, V, Z or 6) **** 8-inch ANSI CL300 weld neck raised face flange 42.7 CMFHC3Y833 *** (N, V, Z or 6) **** 8-inch ANSI CL600 weld neck raised face flange 85.4 CMFHC3Y834 *** (N, V, Z or 6) **** 8-inch ANSI CL900 weld neck raised face flange CMFHC3Y836 *** (N, V, Z or 6) **** 10-inch ANSI CL150 weld neck raised face flange 14.0 CMFHC3Y837 *** (N, V, Z or 6) **** 10-inch ANSI CL300 weld neck raised face flange 42.7 CMFHC3Y838 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 85.4 CMFHC3Y839 *** (N, V, Z or 6) **** 10-inch ANSI CL900 weld neck raised face flange CMFHC4M841 *** (N, V, Z or 6) **** 10-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC4M842 *** (N, V, Z or 6) **** 10-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC4M843 *** (N, V, Z or 6) **** 10-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC4M844 *** (N, V, Z or 6) **** 10-inch ANSI CL900 weld neck raised face flange 98.4 CMFHC4M845 *** (N, V, Z or 6) **** 12-inch ANSI CL150 weld neck raised face flange 13.6 CMFHC4M846 *** (N, V, Z or 6) **** 12-inch ANSI CL300 weld neck raised face flange 35.5 CMFHC4M847 *** (N, V, Z or 6) **** 12-inch ANSI CL600 weld neck raised face flange 70.9 CMFHC4M848 *** (N, V, Z or 6) **** 12-inch ANSI CL900 weld neck raised face flange 98.4 CMFHC4M849 *** (N, V, Z or 6) **** DN250 PN40 weld neck flange; EN Form B CMFHC4M850 *** (N, V, Z or 6) **** DN250 PN100 weld neck flange; EN Form B CMFHC4M851 *** (N, V, Z or 6) **** DN250 PN160 weld neck flange; EN Form B CMFHC4M852 *** (N, V, Z or 6) **** DN300 PN40 weld neck flange; EN Form B CMFHC4M853 *** (N, V, Z or 6) **** DN300 PN100 weld neck flange; EN Form B CMFHC4M854 *** (N, V, Z or 6) **** DN300 PN160 weld neck flange; EN Form B DH150S154 *(N or B) 1½-inch high-pressure clamp-type flange; Size 14 seal ring 64.5 DH150S932 *(N or B) DN40 PN160 weld neck flange; DIN 2638 type E face DH150S933 *(N or B) DN40 PN250 weld neck raised face flange; DIN 2628 type E face DH150S934 *(N or B) DN40 PN320 weld neck raised face flange; DIN 2629 type E face DH150S935 *(N or B) DN40 PN400 weld neck raised face flange; DIN 2627 type E face out DH150S936 *(N or B) 1½-inch ANSI 900/CL1500 weld neck raised face DH150S938 *(N or B) 1½-inch ANSI CL2500 weld neck raised face flange 295.5
13 DH300S156 *(N or B) 3-inch ANSI CL300 weld neck raised face flange 35.5 DH300S157 *(N or B) 3-inch ANSI CL600 weld neck raised face flange 70.9 DH300S164 *(N or B) 4-inch high-pressure clamp-type flange; size 27 seal ring DH300S246 *(N or B) 3-inch ANSI CL900 weld neck raised face flange DH300S942 *(N or B) DN80 PN100 weld neck flange; DIN 2637 type E face 83.8 DH300S943 *(N or B) DN80 PN160 weld neck flange; DIN 2638 type E face DH300S944 *(N or B) DN80 PN250 weld neck raised face flange; DIN 2628 type E face DH300S946 *(N or B) 3-inch ANSI CL1500 weld neck raised face flange DH300S947 *(N or B) 3-inch ANSI CL2500 weld neck raised face flange DL200S226 *(N or B) 2-inch sanitary fitting (Tri-Clamp compatible) 48.0 DL200S227 *(N or B) 2-inch ANSI CL150 lap joint flange 13.1 DL200S228 *(N or B) 2-inch ANSI CL300 lap joint flange 34.1 DL200S954 *(N or B) DN50 DIN11851 aseptic coupling 20.9 DL200S955 *(N or B) DN50 PN40 lap joint flange; 2656 type C face 27.8 DS150Z141 *(N or B) 1½-inch ANSI CL150 weld neck raised face flange 15.5 DS150Z142 *(N or B) 1½-inch ANSI CL300 weld neck raised face flange 40.4 DS150Z143 *(N or B) 1½-inch ANSI CL600 weld neck raised face flange 51.0 DS150Z144 *(N or B) DN40 PN40 weld neck flange; DIN 2635 type C face 38.2 DS150Z218 *(N or B) 2-inch ANSI CL150 weld neck raised face flange 15.5 DS300H203 *(N or B) 3-inch ANSI CL150 lap joint flange 13.1 DS300H204 *(N or B) 3-inch ANSI CL300 lap joint flange 34.1 DS300H211 *(N or B) DN80 PN40 lap joint flange; DIN 2656 type C face 27.8 DS300H949 *(N or B) 3-inch ANSI CL600 lap joint flange 48.5 DS300S155 *(N or B) 3-inch ANSI CL150 weld neck raised face flange 13.6 DS300S156 *(N or B) 3-inch ANSI CL300 weld neck raised face flange 35.5 DS300S157 *(N or B) 3-inch ANSI CL600 weld neck raised face flange 48.0 DS300S158 *(N or B) DN80 PN40 weld neck flange; DIN 2635 type C face 33.5 DS300S161 *(N or B) 3-inch sanitary fitting (Tri-Clamp compatible) 48.0 DS300S941 *(N or B) DN80 PN64 weld neck flange; DIN 2636 type E face 48.0
14 DS300Z155 *(N or B) 3-inch ANSI CL150 weld neck raised face flange 15.5 DS300Z156 *(N or B) 3-inch ANSI CL300 weld neck raised face flange 40.4 DS300Z158 *(N or B) DN80 PN40 weld neck flange; DIN 2635 type C face 38.2 F200H537 *** (N, V or Z) ***** 1½-inch ANSI CL600 lap joint flange 68.6 F200H540 *** (N, V or Z) ***** 1½-inch ANSI CL150 lap joint flange 13.1 F200H541 *** (N, V or Z) ***** 1½-inch ANSI CL300 lap joint flange 34.1 F200H544 *** (N, V or Z) ***** 2-inch ANSI CL150 lap joint flange 13.1 F200H545 *** (N, V or Z) ***** 2-inch ANSI CL300 lap joint flange 34.1 F200H548 *** (N, V or Z) ***** DN40 PN40 lap joint flange; EN Form B F200H549 *** (N, V or Z) ***** DN50 PN40 lap joint flange; EN Form B F200S312 *** (N, V or Z) ***** DN40 PN40 weld neck flange; EN Form D 33.5 F200S316 *** (N, V or Z) ***** DN50 PN40 weld neck flange; EN Form D 33.5 F200S341 *** (N, V or Z) ***** 1½-inch ANSI CL150 weld neck raised face flange 13.6 F200S342 *** (N, V or Z) ***** 1½-inch ANSI CL300 weld neck raised face flange 35.5 F200S343 *** (N, V or Z) ***** 1½-inch ANSI CL600 weld neck raised face flange 70.9 F200S351 *** (N, V or Z) ***** 1½-inch sanitary fitting (Tri-Clamp compatible) 64.5 F200S352 *** (N, V or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 64.5 F200S353 *** (N, V or Z) ***** 40mm DIN11851 aseptic coupling 33.5 F200S354 *** (N, V or Z) ***** 50mm DIN11851 aseptic coupling 20.9 F200S363 *** (N, V or Z) ***** DN40 PN100 weld neck flange; EN Form B F200S365 *** (N, V or Z) ***** DN50 PN100 weld neck flange; EN Form B F200S366 *** (N, V or Z) ***** DN40 PN100 weld neck flange; EN Form D 83.8 F200S367 *** (N, V or Z) ***** DN50 PN100 weld neck flange; EN Form D 83.8 F200S368 *** (N, V or Z) ***** DN40 PN40 weld neck flange; EN Form B F200S369 *** (N, V or Z) ***** DN50 PN40 weld neck flange; EN Form B F200S376 *** (N, V or Z) ***** DN50 PN160 weld neck flange; DIN 2638 type E face F200S378 *** (N, V or Z) ***** DN50 PN100 weld neck flange; DIN 2637 type E face 83.8 F200S381 *** (N, V or Z) ***** DN40 PN40 weld neck flange; DIN 2635 type C face 33.5 F200S382 *** (N, V or Z) ***** DN50 PN40 weld neck flange; DIN 2635 type C face 33.5
15 F200S418 *** (N, V or Z) ***** 2-inch ANSI CL150 weld neck raised face flange 13.6 F200S419 *** (N, V or Z) ***** 2-inch ANSI CL300 weld neck raised face flange 35.5 F200S420 *** (N, V or Z) ***** 2-inch ANSI CL600 weld neck raised face flange 70.9 F300H539 *** (N, V or Z) ***** 3-inch ANSI CL600 lap joint flange 68.6 F300H550 *** (N, V or Z) ***** 3-inch ANSI CL150 lap joint flange 13.1 F300H551 *** (N, V or Z) ***** 3-inch ANSI CL300 lap joint flange 34.1 F300H554 *** (N, V or Z) ***** DN80 PN40 lap joint flange; EN Form B F300S326 *** (N, V or Z) ***** DN80 PN40 weld neck flange; EN Form D 33.5 F300S333 *** (N, V or Z) ***** DN100 PN40 weld neck flange; EN Form D 33.5 F300S355 *** (N, V or Z) ***** 3-inch ANSI CL150 weld neck raised face flange 13.6 F300S356 *** (N, V or Z) ***** 3-inch ANSI CL300 weld neck raised face flange 35.5 F300S357 *** (N, V or Z) ***** 3-inch ANSI CL600 weld neck raised face flange 70.9 F300S359 *** (N, V or Z) ***** DN100 PN100 weld neck flange; EN Form D 83.8 F300S361 *** (N, V or Z) ***** 3-inch sanitary fitting (Tri-Clamp compatible) 64.5 F300S371 *** (N, V or Z) ***** DN80 PN40 weld neck flange; EN Form B F300S372 *** (N, V or Z) ***** DN100 PN40 weld neck flange; EN Form B F300S373 *** (N, V or Z) ***** DN80 PN100 weld neck flange; EN Form B F300S374 *** (N, V or Z) ***** DN100 PN100 weld neck flange; EN Form B F300S375 *** (N, V or Z) ***** DN80 PN100 weld neck flange; EN Form D 83.8 F300S391 *** (N, V or Z) ***** DN80 PN40 weld neck flange; DIN 2635 type C face 33.5 F300S392 *** (N, V or Z) ***** DN100 PN40 weld neck flange; DIN 2635 type C face 33.5 F300S393 *** (N, V or Z) ***** DN80 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 F300S394 *** (N, V or Z) ***** DN100 PN40 weld neck flange; DIN 2635 type N grooved face 33.5 F300S395 *** (N, V or Z) ***** DN80 PN100 weld neck flange; DIN 2637 type E face 83.8 F300S396 *** (N, V or Z) ***** DN100 PN100 weld neck flange; DIN 2637 type E face 83.8 F300S397 *** (N, V or Z) ***** DN80 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 F300S398 *** (N, V or Z) ***** DN100 PN100 weld neck flange; DIN 2637 type N grooved face 83.8 F300S410 *** (N, V or Z) ***** 3-inch Victaulic compatible fitting 48.3 F300S425 *** (N, V or Z) ***** 4-inch ANSI CL150 weld neck raised face flange 13.6
16 F300S426 *** (N, V or Z) ***** 4-inch ANSI CL300 weld neck raised face flange 35.5 F300S427 *** (N, V or Z) ***** 4-inch ANSI CL600 weld neck raised face flange 70.9 H200F352 *** (N, V or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 64.5 H200F354 *** (N, V or Z) ***** DN50 DIN11851 aseptic coupling 20.9 H200F669 *** (N, V or Z) ***** 2s IDF Type CLF2-W aseptic fitting 9.1 H200F678 *** (N, V or Z) ***** DN50 DIN A aseptic coupling 20.9 H200S352 *** (N, V or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 64.5 H200S354 *** (N, V or Z) ***** 50mm DIN11851 aseptic coupling 20.9 H200S669 *** (N, V or Z) ***** 2s IDF Type CLF2-W aseptic fitting 9.1 H200S678 *** (N, V or Z) ***** 50mm DIN A aseptic coupling 20.9 H300F361 *** (N, V or Z) ***** 3-inch sanitary fitting (Tri-Clamp compatible) 64.5 H300F664 *** (N, V or Z) ***** DN76.1 IDF (ISO2853) aseptic coupling 9.1 H300F679 *** (N, V or Z) ***** DN80 DIN A aseptic coupling 20.9 H300F680 *** (N, V or Z) ***** DN80 DIN A aseptic coupling 13.3 H300F685 *** (N, V or Z) ***** DN80 DIN11851 aseptic coupling 20.9 H300F687 *** (N, V or Z) ***** 3s IDF Type CLF2-W aseptic fitting 9.1 H300F694 *** (N, V or Z) ***** DN76 SMS 1145 aseptic coupling 5.1 H300S361 *** (N, V or Z) ***** 3-inch sanitary fitting (Tri-Clamp compatible) 64.5 H300S664 *** (N, V or Z) ***** DN76.1 IDF (ISO2853) aseptic coupling 9.1 H300S679 *** (N, V or Z) ***** DN80 DIN A aseptic coupling 20.9 H300S680 *** (N, V or Z) ***** DN80 DIN A aseptic flange 13.3 H300S685 *** (N, V or Z) ***** DN80 DIN11851 aseptic coupling 20.9 H300S687 *** (N, V or Z) ***** 3s IDF Type CLF2-W aseptic fitting 9.1 H300S694 *** (N, V or Z) ***** DN76 SMS 1145 aseptic coupling 5.1 R200S312 *** (N or Z) ***** DN40 PN40 weld neck flange; EN Form D 33.5 R200S316 *** (N or Z) ***** DN50 PN40 weld neck flange; EN Form D 33.5 R200S341 *** (N or Z) ***** 1½-inch ANSI CL150 weld neck raised face flange 13.6 R200S342 *** (N or Z) ***** 1½-inch ANSI CL300 weld neck raised face flange 35.5 R200S343 *** (N or Z) ***** 1½-inch ANSI CL600 weld neck raised face flange 70.9
17 R200S351 *** (N or Z) ***** 1½-inch sanitary fitting (Tri-Clamp compatible) 64.5 R200S352 *** (N or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 64.5 R200S353 *** (N or Z) ***** 40mm DIN11851 aseptic coupling 33.5 R200S354 *** (N or Z) ***** 50mm DIN11851 aseptic coupling 20.9 R200S363 *** (N or Z) ***** DN40 PN100 weld neck flange; EN Form B R200S365 *** (N or Z) ***** DN50 PN100 weld neck flange; EN Form B R200S366 *** (N or Z) ***** DN40 PN100 weld neck flange; EN Form D 83.8 R200S367 *** (N or Z) ***** DN50 PN100 weld neck flange; EN Form D 83.8 R200S368 *** (N or Z) ***** DN40 PN40 weld neck flange; EN Form B R200S369 *** (N or Z) ***** DN50 PN40 weld neck flange; EN Form B R200S376 *** (N or Z) ***** DN50 PN160 weld neck flange; DIN 2638 type E face R200S378 *** (N or Z) ***** DN50 PN100 weld neck flange; DIN 2637 type E face 83.8 R200S381 *** (N or Z) ***** DN40 PN40 weld neck flange; DIN 2635 type C face 33.5 R200S382 *** (N or Z) ***** DN50 PN40 weld neck flange; DIN 2635 type C face 33.5 R200S418 *** (N or Z) ***** 2-inch ANSI CL150 weld neck raised face flange 13.6 R200S419 *** (N or Z) ***** 2-inch ANSI CL300 weld neck raised face flange 35.5 R200S420 *** (N or Z) ***** 2-inch ANSI CL600 weld neck raised face flange 70.9 T150F624 *** (N, V or Z) ***** 1½-inch sanitary fitting (Tri-Clamp compatible) 66.9 T150F625 *** (N, V or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 66.9 T150F641 *** (N, V or Z) ***** 1½-inch ANSI CL150 socket weld raised face flange 14.8 T150F642 *** (N, V or Z) ***** 1½-inch ANSI CL300 socket weld raised face flange 38.6 T150F643 *** (N, V or Z) ***** 1½-inch ANSI CL600 socket weld raised face flange 77.2 T150F644 *** (N, V or Z) ***** 2-inch ANSI CL150 socket weld raised face flange 14.8 T150F645 *** (N, V or Z) ***** 2-inch ANSI CL300 socket weld raised face flange 38.6 T150F646 *** (N, V or Z) ***** 2-inch ANSI CL600 socket weld raised face flange 77.2 T150F652 *** (N, V or Z) ***** DN40 PN40 socket weld flange; DIN 2512 type N grooved face 36.4 T150F653 *** (N, V or Z) ***** DN50 PN40 socket weld flange; DIN 2512 type N grooved face 36.4 T150F663 *** (N, V or Z) ***** DN51 IDF (ISO2853) aseptic coupling 9.5 T150F673 *** (N, V or Z) ***** DN40 DIN aseptic coupling 30.9
18 T150F674 *** (N, V or Z) ***** DN50 DIN aseptic coupling 19.2 T150F678 *** (N, V or Z) ***** DN50 DIN A aseptic coupling 19.2 T150F681 *** (N, V or Z) ***** DN40 PN40 socket weld flange; DIN 2526 type C face 36.4 T150F682 *** (N, V or Z) ***** DN40 PN100 socket weld flange; DIN 2526 type E face 91.1 T150F683 *** (N, V or Z) ***** DN50 PN40 socket weld flange; DIN 2526 type C face 36.4 T150F684 *** (N, V or Z) ***** DN50 PN100 socket weld flange; DIN 2526 type E face 91.1 T150F693 *** (N, V or Z) ***** DN51 SMS 1145 aseptic coupling 5.8 T150T624 *** (N, V or Z) ***** 1½-inch sanitary fitting (Tri-Clamp compatible) 66.9 T150T625 *** (N, V or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 66.9 T150T641 *** (N, V or Z) ***** 1½-inch ANSI CL150 socket weld raised face flange 14.8 T150T642 *** (N, V or Z) ***** 1½-inch ANSI CL300 socket weld raised face flange 38.6 T150T643 *** (N, V or Z) ***** 1½-inch ANSI CL600 socket weld raised face flange 77.2 T150T644 *** (N, V or Z) ***** 2-inch ANSI CL150 socket weld raised face flange 14.8 T150T645 *** (N, V or Z) ***** 2-inch ANSI CL300 socket weld raised face flange 38.6 T150T646 *** (N, V or Z) ***** 2-inch ANSI CL600 socket weld raised face flange 77.2 T150T652 *** (N, V or Z) ***** DN40 PN40 socket weld flange; DIN 2512 type N grooved face 36.4 T150T653 *** (N, V or Z) ***** DN50 PN40 socket weld flange; DIN 2512 type N grooved face 36.4 T150T656 *** (N, V or Z) ***** DN40 PN40 weld neck flange; EN Form D 36.4 T150T657 *** (N, V or Z) ***** DN50 PN40 weld neck flange; EN Form D 36.4 T150T658 *** (N, V or Z) ***** DN40 PN40 weld neck flange; EN Form B T150T659 *** (N, V or Z) ***** DN40 PN100 weld neck flange; EN Form B T150T660 *** (N, V or Z) ***** DN50 PN40 weld neck flange; EN Form B T150T661 *** (N, V or Z) ***** DN50 PN100 weld neck flange; EN Form B T150T663 *** (N, V or Z) ***** DN51 IDF (ISO2853) aseptic coupling 9.5 T150T673 *** (N, V or Z) ***** DN40 DIN aseptic coupling 30.9 T150T674 *** (N, V or Z) ***** DN50 DIN aseptic coupling 19.2 T150T678 *** (N, V or Z) ***** DN50 DIN A aseptic coupling 19.2 T150T681 *** (N, V or Z) ***** DN40 PN40 socket weld flange; DIN 2526 type C face 36.4 T150T682 *** (N, V or Z) ***** DN40 PN100 socket weld flange; DIN 2526 type E face 91.1
19 T150T683 *** (N, V or Z) ***** DN50 PN40 socket weld flange; DIN 2526 type C face 36.4 T150T684 *** (N, V or Z) ***** DN50 PN100 socket weld flange; DIN 2526 type E face 91.1 T150T693 *** (N, V or Z) ***** DN51 SMS 1145 aseptic coupling 5.8 DL200S955 *(N or Z) DN50 PN40 lap joint flange; 2656 type C face 40 DT150H142 *(N or Z) 1½-inch ANSI CL300 weld neck raised face flange 41 DT150H143 *(N or Z) 1½-inch ANSI CL600 weld neck raised face flange 41 DT150H144 *(N or Z) DN40 PN40 weld neck flange; DIN 2635 type C face 40 T150* 641 *** (N or Z) ***** 1½-inch ANSI CL150 socket weld raised face flange 18 T150* 642 *** (N or Z) ***** 1½-inch ANSI CL300 socket weld raised face flange 49 T150* 643 *** (N or Z) ***** 1½-inch ANSI CL600 socket weld raised face flange 99 T150* 644 *** (N or Z) ***** 2-inch ANSI CL150 socket weld raised face flange 18 T150* 645 *** (N or Z) ***** 2-inch ANSI CL300 socket weld raised face flange 49 T150* 646 *** (N or Z) ***** 2-inch ANSI CL600 socket weld raised face flange 99 T150* 681 *** (N or Z) ***** DN40 PN40 socket weld flange; DIN 2526 type C face 40 T150* 682 *** (N or Z) ***** DN40 PN100 socket weld flange; DIN 2526 type E face 100 T150* 683 *** (N or Z) ***** DN50 PN40 socket weld flange; DIN 2526 type C face 40 T150* 684 *** (N or Z) ***** DN50 PN100 DIN 2637 socket weld flange; DIN 2526 type E face 100 T150* 652 *** (N or Z) ***** DN40 PN40 socket weld flange; DIN 2512 type N grooved face 40 T150* 653 *** (N or Z) ***** DN50 PN40 socket weld flange; DIN 2512 type N grooved face 40 T150* 624 *** (N or Z) ***** 1½-inch sanitary fitting (Tri-Clamp compatible) 10 T150* 625 *** (N or Z) ***** 2-inch sanitary fitting (Tri-Clamp compatible) 10 T150* 673 *** (N or Z) ***** DN40 DIN aseptic coupling 40 T150* 674 *** (N or Z) ***** DN50 DIN aseptic coupling 25 T150* 693 *** (N or Z) ***** DN51 SMS 1145 aseptic coupling 6 T150* 663 *** (N or Z) ***** DN51 IDF (ISO2853) aseptic coupling 3 T150* 678 *** (N or Z) ***** DN50 DIN A aseptic coupling 25
20 2012 Micro Motion, Inc. All rights reserved. P/N , Rev. BB * * For the latest Micro Motion product specifications, view the PRODUCTS section of our web site at Micro Motion Inc. USA Worldwide Headquarters 7070 Winchester Circle Boulder, Colorado T F Micro Motion Europe Emerson Process Management Neonstraat WX Ede The Netherlands T +31 (0) F +31 (0) Micro Motion United Kingdom Emerson Process Management Limited Horsfield Way Bredbury Industrial Estate Stockport SK6 2SU U.K. T F Micro Motion Asia Emerson Process Management 1 Pandan Crescent Singapore Republic of Singapore T F Micro Motion Japan Emerson Process Management 1-2-5, Higashi Shinagawa Shinagawa-ku Tokyo Japan T F
ATEX Installation Instructions for Micro Motion ELITE CMFS Sensors
Installation Instructions P/N MMI-20015054, Rev. AA May 2009 ATEX Installation Instructions for Micro Motion ELITE CMFS Sensors For ATEX-approved sensor installations Note: For hazardous installations
Micro Motion Model D and DL Coriolis Flow and Density Meters
Product Data Sheet PS-00388, Rev. F April 2013 Micro Motion Model D and DL Coriolis Flow and Density Meters Micro Motion Model D and DL sensors provide flow and density measurement for liquids, gases,
ATEX Zone 2 and 22 Installation Drawings and Instructions
Installation Instructions P/N 20004425, Rev. CA June 2009 ATEX Zone 2 and 22 Installation Drawings and Instructions For ATEX-approved Zone 2 and 22 installations Note: For hazardous installations in Europe,
Micro Motion ELITE CMFS Series Meter
Revolutionize your Coriolis measurement technology Micro Motion ELITE CMFS Series Meter Introducing Emerson s Micro Motion Elite CMFS Series METER Our ELITE CMFS meter delivers unmatched, real-world performance
Micro Motion Model 2200S Transmitters
Installation Manual P/N MMI-20012740, Rev. BA February 2009 Micro Motion Model 2200S Transmitters Installation Manual 2009, Micro Motion, Inc. All rights reserved. ELITE and ProLink are registered trademarks,
ISO 17025 Accreditation for a Standing Start Finish (SSF) Primary Flow Stand with Coriolis Flowmeters as Reference Standards.
MICRO MOTION WHITE PAPER BY M. LEE, D. STANDIFORD, MICRO MOTION, INC. A. PRUYSEN, EMERSON PROCESS MANAGEMENT ISO 17025 Accreditation for a Standing Start Finish (SSF) Primary Flow Stand with Coriolis Flowmeters
Micro Motion 3098 Gas Specific Gravity Meter
Product Data Sheet PS-001161, Rev. D April 2013 Micro Motion 3098 Gas Specific Gravity Meter Micro Motion density and concentration meters are built to tackle the most demanding process and fiscal applications.
Rosemount 1199 Submersible Seal
Product Data Sheet July 2013 00813-0400-4016, Rev AA The Rosemount Submersible Seal design uses innovative DP level technology to measure level for top-down applications. For this design, the seal and
Rosemount 1199 Submersible Seal
Product Data Sheet January 2015 00813-0400-4016, Rev BB The Rosemount Submersible Seal design uses innovative DP Level technology to measure level for top-down applications. For this design, the seal and
Micro Motion Modbus Interface Tool
Instruction Manual P/N MMI-211275, Rev. AB August 21 Micro Motion Modbus Interface Tool Getting Started Manual 21 Micro Motion, Inc. All rights reserved. The Micro Motion and Emerson logos are trademarks
Installation Manual 20002158, Rev DK November 2015. Micro Motion ELITE Coriolis Flow and Density Sensors
Installation Manual 20002158, Rev DK November 2015 Micro Motion ELITE Coriolis Flow and Density Sensors Safety and approval information This Micro Motion product complies with all applicable European directives
Oilfield Services Measurement Solutions
Oilfield Services Measurement Solutions Superior flow and density measurement Best-in-class measurement How can I streamline my operations for efficiency without compromising environmental, safety and
OPTIMASS 1400 Technical Datasheet
OPTIMASS 1400 Technical Datasheet Sensor for mass flow First choice for universal applications Best price-performance ratio A wide range of options available with no restrictions The documentation is only
Order Code for GEA Tuchenhagen VESTA Sterile Valves. Type H_A 2/2 Way Seat Valve
Order Code for VESTA Sterile Valves Type H_A 2/2 Way Seat Valve engineering for a better world GEA Mechanical Equipment VESTA Sterile Valves are designed for universal use in sterile process technology.
Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
OPTIMASS 6000 Technical Datasheet
OPTIMASS 6000 Technical Datasheet Sensor for mass flow The high performance meter for process industries Cryogenic, high temperature and high pressure options Supreme liquid and gas performance with CT
Company Profile. 1-2-1 Osaki, Shinagawa-ku, Tokyo, 141-8672 Japan Tel. +81 3 5435 7777 www.hitachi-systems.com/eng/
Company Profile 1-2-1 Osaki, Shinagawa-ku, Tokyo, 141-8672 Japan Tel. +81 3 5435 7777 www.hitachi-systems.com/eng/ All product and company names in this document are trademarks or registered trademarks
Chemical Measurement Solutions
Chemical Measurement Solutions Superior flow and density measurement Best-in-class measurement I need to simultaneously increase production and plant up-time while lowering operations and maintenance costs.
Electromagnetic Flow Meter
Electromagnetic Flow Meter Description The EL 2200 series of electromagnetic sensors represent the state of the art for the accurate measurement for water cycle and process applications. Flow meters are
Instructions Manual. Electromagnetic sensor Series FLOMID FX. instrumentation for fluids. R-MI-FlomidFX Rev.: 0 English version
instrumentation for fluids Electromagnetic sensor Series FLOMID FX Instructions Manual! Conforms with the Pressure Equipment Directive 97/23/EC. 0830 This equipment is considered as being a pressure accessory
Micro Motion Net Oil Computer Software and NOC System
Instruction Manual P/N 20006444, Rev. A May 2007 Micro Motion Net Oil Computer Software and NOC System Configuration and Use Manual 2007, Micro Motion, Inc. All rights reserved. ELITE and ProLink are registered
www.kem-kueppers.com info@kem-kueppers.com Certified according to DIN EN ISO 9001 Technical Datasheet KVO Series Vortex Flow Meter
www.kem-kueppers.com Certified according to DIN EN ISO 9001 Technical Datasheet KVO Series Vortex Flow Meter Description The KVO Vortex flow meters utilize two primary sensing elements a vortex shedding
EVAC ONLINEVAC TECHNICAL DATA 6547655 EVAC ONLINEVAC 16, 24 V DC. Required maintenance space 700 mm. Required maintenance space 200 mm 360 Ø13
Date: 9 Apr 202 Doc. 002967-6547655 6, 24 V DC Ø3 360 Required maintenance 990±0 960 40 040 20 890 350 (P/N 546664) 95±5 67±5 Vacuum sensor G /4 88±5 INLET DN40 943 Connection Frame: Steel S235 EN 0025
TECHNICAL BULLETIN. Kämmer LinedFlow - 132000 Corrosive Application Valves. Experience In Motion FCD KMENTB3221-01 04/12
TECHNICAL BULLETIN Kämmer LinedFlow - 132000 Corrosive Application Valves FCD KMENTB3221-01 04/12 Experience In Motion Description ¼-inch NPT test port Large guided stem area Bellows seal eliminates stem
FCD VVABR0003-00. Vogt Valves. Product Overview. Vogt Valves
FCD VVABR0003-00 Vogt Valves Product Overview Vogt Valves Flowserve Vogt Valves A Name Everyone Recognizes In the late 1890s, Henry Vogt Machine Company pioneered the development of ammonia absorption
SUPRApak S Series Filter Housings SUPRApak Filtration For Small Batch Depth Filtration
SUPRApak S Series Filter Housings SUPRApak Filtration For Small Batch Depth Filtration FBSPAKSWASAENc SUPRApak Series SUPRApak S Series Filter Housings Technical Information SUPRApak S series filter housings
Fisher ENVIRO-SEAL and HIGH-SEAL Packing Systems for Sliding-Stem Valves (Live-Loaded)
Sliding-Stem Live-Loaded Packing Product Bulletin Fisher ENVIRO-SEAL and HIGH-SEAL Packing Systems for Sliding-Stem Valves (Live-Loaded) Fisher ENVIRO-SEAL and HIGH-SEAL live-loaded packing systems offer
Bypass level indicator With magnetic display Model BNA
Level measurement Bypass level indicator With magnetic display Model BNA WIKA data sheet LM 10.01 Applications Continuous level indication without power supply Indication of the level proportional to height
COPYRIGHT Danish Standards. NOT FOR COMMERCIAL USE OR REPRODUCTION. DS/EN 1515-1:2000
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1515-1 November 1999 ICS 21.060.10; 21.060.20; 23.040.60 English version Flanges and their joints - Bolting - Part 1: Selection of bolting Brides
Micro Motion 7829 Visconic Viscosity Meter
Product Data Sheet PS-001183, Rev. C April 2013 Micro Motion 7829 Visconic Viscosity Meter Micro Motion viscosity meters are built to tackle the most demanding industrial and process applications. Rugged
SITRANS F flowmeters SITRANS F M
Overview Integration The complete flowmeter consists of a flow sensor and an associated transmitter MAG 5000, 6000 or 6000 I. The flexible communication concept USM II simplifies integration and update
Valves dimension of pressure (lbs) ANSI2500 ANSI1500 ANSI900 ANSI600 ANSI300 ANSI150. Inch. from 1/2 up to 6
+SBF CARBON STEEL Type: ball valve SBF ANSI B16.5 Body: round Material: A105/F316 Ball seats: from DN13 up to DN150 O-Rings: NBR, FKM, EPDM, MVQ Operating pressure: 20 Bar - 50 Bar - 100 Bar 150 Bar -
Fisher CV500 Rotary Globe Control Valve
CV500 Valve D101606012 Product Bulletin Fisher CV500 Rotary Globe Control Valve The Fisher CV500 Cam Vee-Ball control valve combines the rangeability of the cammed-segmented V-notched ball, with the inherent
Micro Motion Compact Density Meters
Micro Motion Compact Density Meters Peak performance precision density meter installation Installation Manual MMI-20020974, Rev C May 2015 Safety and approval information This Micro Motion product complies
2-Port Self-acting Temperature Control Valve Selection for Heating and Cooling Applications
Page 1 of 12 TI-S21-07 CH Issue 1 Cert. No. LRQ 0963008 ISO 9001 2-Port Self-acting Temperature Control Valve Selection How to select a system Valve selection: 1. Is the application for heating or cooling?
How To Use A Flowmeter
INLINE flowmeter for continuous flow measurement Economic integration in pipe systems without any additional piping 3-wire frequency pulse version to directly interface with PLC s (both PNP and NPN) Connection
Geberit Mapress Catalogue 2008 / 2009. Valid from 1 April 2008
Geberit Mapress Catalogue 2008 / 2009 Vali from 1 April 2008 Mapress Stainless Steel Page 3 Mapress CrNi Steel Page 23 Mapress Stainless Steel silicone-free Page 25 Mapress Stainless Steel Gas Page 39
NELES SOFT SEATED BUTTERFLY VALVE SERIES MAPAG BA FOR PSA PLANT ON/OFF AND CONTROL SERVICE
NELES SOFT SEATED BUTTERFLY VALVE SERIES MAPAG BA FOR PSA PLANT ON/OFF AND CONTROL SERVICE Series Mapag BA is a wafer type butterfly valve with a one piece body and soft seat.. It is specially designed
Flow Monitoring System
FMS-3 Product Data Sheet PS-00028 April 1997 Flow Monitoring System FMS-3 Flow Monitoring System The Micro Motion FMS-3 Flow Monitoring System is a microprocessor-based batch controller with rate, total,
Variable V Area Flowmeter Rotameter The Original
Variable V Area Flowmeter Rotameter The Original 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com precise measurement of liquids
Model 4418F. www.amot.com. Overview. Typical applications. Key features and benefits. Accreditations. Starting air/gas valve Vented fuel gas valve
High Pressure Control Valve Model 4418F Overview The 4418F has been designed specifically for use as an air start valve for diesel engines or as a fuel shut-off valve for gas turbine applications. Its
4. Combi valves. 7. Fire hydrants. 8. Check valves. 9. Air valves
1. General company and product information 2. Flanged gate valves for water 3. Other gate valves for water 4. Combi valves 5. Service connection valves for water 6. Valves and fittings for gas 7. Fire
Fluxi 2000/TZ Turbine Gas Meter
Gas Fluxi 2000/TZ Turbine Gas Meter Turbine gas meters are flow meters. The flow of gas turns a turbine wheel, and thus, the rotating speed of the turbine is proportional to the linear speed of the gas.
Nozzle Check Valves. NOREVA nozzle check valves are used
Nozzle Check Valves NOREVA nozzle check valves are used in applications where the reverse flow of a fluid has to be avoided. These valves are suitable for all kind of liquid and gaseous fluids and fire
Plate heat exchanger. Applications General heating and cooling duties. Heating by means of steam.
M3 Plate heat exchanger Applications General heating and cooling duties. Heating by means of steam. Standard design The plate heat exchanger consists of a pack of corrugated metal plates with portholes
The Unique Accelabar Flow Meter
The Unique Accelabar Flow Meter The Accelabar is a new and unique flow meter that combines two differential pressure technologies to produce operating ranges never before attainable in a single flow meter.
24V DRIVE INTERFACE BOARD (SERIAL) FTP-622DSL001/011/012/112
24V DRIVE INTERFACE BOARD (SERIAL) FTP-622DSL001/011/012/112 FOR FTP-622/632/642MCL001/002/301/302/303/304 DESIGNATION SERIAL INTERFACE BOARD Product Part Number Function FTP-622DSL001 FTP-622DSL011 FTP-622DSL012
Baumann 87000 Flexsleev Sanitary Control Valve
Product Bulletin D103345X012 Baumann 87000 Flexsleev Sanitary Control Valve The Baumann 87000 control valve (figures 1 and 2) is excellent for throttling high purity liquid or gaseous media commonly found
Fisher GX Control Valves
Fisher GX Control Valves Fisher GX Control Valves Innovation. Technology. Reliability. Emerson engineers started with a clean slate in developing Fisher GX control valves. Their goal was to bring unmatched
Metal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
Reliable Pressure Measurement with Remote Diaphragm Seals in Cold Weather Applications
Reliable Pressure Measurement with Remote Diaphragm Reliable Pressure Measurement with Remote Diaphragm Introduction............................................................... page 1 Rosemount 3051S
SanStar Series SSi and SSO Mixers SANITARY MIXERS
SanStar Series SSi and SSO Mixers SANITARY MIXERS A World Leader In Industrial Mixing Since 1923. Lightnin has 90 years of unrivaled experience in industrial mixing technology, process knowledge, and technological
Daniel Orifice Fittings Brochure. Senior Orifice Fitting, Simplex Orifice Plate Holder, Junior Orifice Fitting, Orifice Flange Union, Meter Tubes
Daniel Orifice Fittings Brochure Senior Orifice Fitting, Simplex Orifice Plate Holder, Junior Orifice Fitting, Orifice Flange Union, Meter Tubes Is unaccounted hydrocarbon draining your bottom line? When
Uncompromising Customer Service. Baumann TM Sanitary and Aseptic Process Valves
Baumann TM Sanitary and Aseptic Process Valves The Company Fisher Controls International LLC, Baumann Control Valves, is an ISO 9001 certified, PED compliant manufacturer of general utility, precision
High CATALOG. LESER worldwide. Performance. Flanged Safety Relief Valves Series 441 Series 441 Full nozzle Series XXL Series 444 Series 458
LESER UK Bristol sales@leser.co.uk LESER Germany Hamburg and Hohenwestedt sales@leser.com André Ramseyer AG Flamatt, Switzerland info@ramseyer.ch LESER China Tianjin, Beijing, Shanghai and Shenzhen sales.china@leser.com
S GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
kymanual or Automatic - it s your Choice
. kymanual or Automatic - it s your Choice ky LKB Automatic or Manual Butterfly Valve Application LKB is a sanitary automatically or manually operated butterfly valve for use in stainless steel pipe systems.
Rosemount 333 HART Tri-Loop
Product Data Sheet September 2014 00813-0100-4754, Rev GA Rosemount 333 HART Tri-Loop HART-to-Analog Signal Converter Convert a digital HART signal into three additional analog signals Easy to configure
DMH. Magnetic Inductive Flowmeter. for conductive fluids. Measuring range: 0.05 40376 m 3 /h. Accuracy: ± 0.3% of reading ± 0.
Magnetic Inductive Flowmeter for conductive fluids measuring monitoring analysing MH Measuring range: 0.05 40376 m 3 /h ccuracy: ± 0.3% of reading ± 0.01% x Q max p max : PN40; t max : -20... +150 C O
Baumann 24000 Little Scotty Bronze Control Valve
24000 Valve Product Bulletin Baumann 24000 Little Scotty Bronze Control Valve Baumann Little Scotty industrial control valves are intended for general utility service in pressure, flow, and temperature
www.kem-kueppers.com info@kem-kueppers.com Certified according to DIN EN ISO 9001 Technical Datasheet TRICOR Series Mass Flow Meters
www.kem-kueppers.com info@kem-kueppers.com Certified according to DIN EN ISO 9001 Technical Datasheet TRICOR Series Mass Flow Meters Description The Tricor Mass Flow Meters measure simultaneously mass
Brooks Models SLA5850, SLA5851, SLA5853 Mass Flow Controllers and Models SLA5860, SLA5861, SLA5863 Mass Flow Meters
Data Sheet Brooks Digital MFC's & MFM's Brooks Models SLA5850, SLA5851, SLA5853 Mass Flow Controllers and Models SLA5860, SLA5861, SLA5863 Mass Flow Meters GENERAL FEATURES Wide FS flow range for measurement
Pneumatic Control and Shut-off Butterfly Valve Pfeiffer Type BR 14b/31a and Type BR 14c/31a
Pneumatic Control and Shut-off Butterfly Valve Pfeiffer Type BR 14b/31a and Type BR 14c/31a Application Tight-closing, double eccentric butterfly valve for process engineering and plants with industrial
T U R B I N E G A S M E T E R
TURBINE GAS METER TURBINE GAS METER CGT 1 2 3 4 5 6 7 Design and function page 2 General technical data page 3 Measurement outputs page 4 Dimensions and weights page 5 Performance page 7 Pressure loss
Rosemount 333 HART Tri-Loop
Product Data Sheet Rosemount 333 Rosemount 333 HART Tri-Loop HART-TO-ANALOG SIGNAL CONVERTER Convert a digital HART signal into three additional analog signals Easy to configure and install Accessory product
Hose & Coupling Solutions Dixon Europe
Hose & Coupling Solutions Dixon Europe The Story so far......the Dixon Group is a world leading supplier of hose and coupling products. It prides itself on its reputation for quality and innovation. It
FLEXIBLE SOLUTIONS FOR FLUIDS AND GASES
FLEXIBLE SOLUTIONS FOR FLUIDS AND GASES www.amnitec.nl AmniTec B.V., Rotterdam, is part of a group of companies called United Flexible with an annual turnover of $ 70 Million and 5 operating facilities
Sampling Solutions. Fuel and Lube Oil sampling Equipment. Convenient, Representative, Approved.
Sampling Solutions Fuel and Lube Oil sampling Equipment. Convenient, Representative, Approved. Oil Samples are used to obtain a clear indication of the operating status of your machinery. One of the most
HFS and HFD Series. High Flow Single and Duplex Filters Max. 11200 l/min. 10 bar. Heavy Duty Reliability. Applications: Contact Information:
High Flow Single and Duplex Filters Max. 11200 l/min. 10 bar Heavy Duty Reliability New High Flow Single and Duplex Filters ensure reliability in industrial, marine, and power generation applications up
Spira-trol TM Two-port Control Valves EN Standard KE, KF and KL DN15 to DN300 and ASME Standard KEA, KFA and KLA ½" to 12"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
LEVEL CONTROL INSTRUMENTATION
SU C C E S S C A N BE M E A S U R E D Foto: KHS GmbH LEVEL CONTROL INSTRUMENTATION FOR THE FOOD PROCESSING INDUSTRY PRECISION QUALITY PASSION YOUR SUCCESS IS OUR GOAL TAILOR-MADE LEVEL CONTROL INSTRUMENTATION
VdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
BWX SERIES BUTTERFLY VALVE FOR CRYOGENIC APPLICATIONS
BWX SERIES BUTTERFLY VALVE FOR CRYOGENIC APPLICATIONS The BWX series butterfly valve has been especially designed for use in cryogenic applications with high quality CrNi steel. Testing of the valve includes
Butterfly Valves PN 6/10/16 for flanged connection
4 136 ACVATIX Butterfly Valves PN 6/10/16 for flanged connection tight-closing VKF46.. VKF46..TS Grey cast iron housing EN-GJL-250 (to DN 300) nodular cast iron housing EN-GJS-400-15 (from DN 350) DN 40
Stainless steel process fittings
Page 1/6 Stainless steel process fittings Installation in pipe systems Installation in tanks and vessels Hygienic version FDA conformity of materials Probe length 120 mm 120 mm Availability of various
Armaturenwerk Hötensleben GmbH. AWH-Connect
Armaturenwerk Hötensleben GmbH The aseptic connection for vessels "A must for clean vessels " is the aseptic and hygienic connection for your vessels. It was developed for the strict requirements of the
ISO/VDMA Actuators. Engineering GREAT Solutions
ISO/VDMA Actuators Engineering GREAT Solutions 02 ISO/VDMA Actuators Contents 03 Introduction 04 ISO/VDMA Actuators 06 The ISO/VDMA Range 08 Industrial Options 10 Cleanline Options 12 IVAC innovation to
Dimensions. LUC-M20 with F12 housing and process connection 2" approx. 86 AF60 G2 2 NPT Ø50. Additional dimensions see section dimensions.
Dimensions LUC-M20 with F12 housing and process connection 2" approx. 86 65 78 Ø129 150 AF60 85 G2 2 NPT 22 ~148 Ø50 ~83 Additional dimensions see section dimensions. Features Quick and simple commissioning
VAD. Variable Area Desuperheaters
Desuperheater overview Steam used in process plants can be superheated, that is, heated to a temperature above saturation. The excess of temperature above its saturation is called 'superheat'. Desuperheated
HYDRAULIC PIPING STANDARD HANDBOOK. Revision 1
HYDRAULIC PIPING STANDARD HANDBOOK Revision 1 Preface We aim to fill a gap in technical literature. At this moment there are no hydraulic piping standards available which cover different pressure classes
Digital inductive conductivity transmitter
Digital inductive conductivity transmitter Optimal solution for conductivity measurements in difficult fluids (polluted, dirty,...) PEEK/PPA version for CIP applications Large range of process connections
CRANE. Σελίδα 1 από 2. Dimensions and Weights. Weight (kg) Size
CRANE Σελίδα από 2 DM93 Variable Orifice Double Regulating Valve PN6 Cast Iron Balancing Valve (VODRV), Flanged to BSEN 92-2 The DM93 variable orifice double regulating valves will give satisfactory performance
Grey cast iron SG iron Forged steel/ Cast steel Stainless steel Fig. 631 Page 2. High temperature steel Fig. 631 / Fig. 632 Page 8
Ball float steam trap CONA S Ball float steam trap Ball float steam trap PN16 / PN40 - with flanges (Fig. 631...1) - with screwed sockets (Fig. 631...2) - with socket weld ends (Fig. 631...3) - with butt
Replacing Displacers with Guided Wave Radar
ROSEMOUNT GUIDED WAVE RADAR Replacing Displacers with Guided Wave Radar KEY POINTS Mounting flanges vary by displacer supplier Probe must extend the of the displacer chamber Single rigid probes are the
EUROPEAN OEM SERVICE STAUFF. STAUFF - Line - Local solutions for individual customers worldwide
EUROPEAN OEM SERVICE STAUFF STAUFF - Line - Local solutions for individual customers worldwide STAUFF - Line - Experienced staff and precision machinery enable the manufacture of high-quality hydraulic
Types 66R and 66RR Low-Pressure Relief Valves
November 2009 Types 66R and 66RR Low-Pressure Relief Valves W1953 W1908 TYPE 66R RELIEF VALVE TYPE 66RR RELIEF VALVE Figure 1. Typical Constructions Introduction Types 66R and 66RR low-pressure throttling
NEW CONNECTION INDUSTRIAL PRODUCTS NC.10V NC.20V NC.30V. NC. SD.10 NC. SD.20 NC. F.Clamp
Repair and Construction. Complete stainless steel pipe repair clamps to repair cracks, fractures, pin holes, torn sockets or welded tees, broken asbest-cement pipe coupling and more. Available for all
Level Plus. Magnetostrictive Liquid-Level Sensors with Temposonics Technology. M-Series Model MG Transmitter with Digital Output.
Level Plus Magnetostrictive Liquid-Level Sensors with Temposonics Technology M-Series Model MG Transmitter with Digital Output SENSORS Document Part Number 550784 Revision J Data Sheet FEATURES Modbus
WD600 STEAM TRAPS. Thermodynamic Steam Trap
WD600 Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company WD600, WD600L Sizes 3/8, 1/2, 3/4, 1 NPT Material Stainless
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
extreme applications as standard
grundfos INDUSTRY The insurmountable CR extreme applications as standard THE unsurmountable CR A company you can trust Back in 1971 Grundfos shocked the pump world with the introduction of the CR30 - the
QLM and QLD Series Three-port Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
DOUBLE GATE KNIFE GATE VALVE
DOUBLE GATE KNIFE GATE VALVE The model knife gate is a bi-directional valve widely used in the Pulp and Paper industry (recycling or secondary fibre processing) designed to handle high concentrated or
CLEAN COMBUSTION. CLEAR SOLUTIONS. John Zink Vapor Combustion System
CLEAN COMBUSTION. CLEAR SOLUTIONS. John Zink Vapor Combustion System The John Zink Advantage A Commitment to Excellence John Zink engineers can design VCUs to meet worldwide mechanical and electrical standards
Level Plus. Magnetostrictive Liquid-Level Sensors with Temposonics Technology. M-Series Model MR Transmitter with Analog Output.
Level Plus Magnetostrictive Liquid-Level Sensors with Temposonics Technology M-Series Model MR Transmitter with Analog Output Data Sheet SENSORS Document Part Number 550677 Revision J Features 4 to 20
CRN32-2-2 A-F-G-E-HQQE 3x400D 50 HZ
GRUNDFOS DATA BOOKLET CRN32-2-2 A-F-G-E-HQQE 3x4D 5 HZ Grundfos Pump 96122352 Thank you for your interest in our products Please contact us for more information, or visit our website http://www.lenntech.com/grundfos/crn32/96122352/crn-32-2-2-a-f-g-e-hqqe.html
SUPRApak Multi-Stack Series Filter Housings SUPRApak Filtration For High Volume Depth Filtration
SUPRApak Multi-Stack Series Filter Housings SUPRApak Filtration For High Volume Depth Filtration FBSPAKMSWAEN Technical Information SUPRApak Multi-Stack Series-WA housings are designed for use with SUPRApak
Kämmer Series 185000 Laboratory Valves
flowserve.com Kämmer Series 185000 Laboratory Valves Description Kämmer microflow series 185000 / 285000 and 187000 / 287000 are ½" laboratory valves designed for precision controlling. The bodies in stainless
POWER RELAY. JV Series. 1 POLE - 5A/10A Medium Load Control FTR-K1 SERIES FEATURES
FTR-K1 SERIES POWER RELAY 1 POLE - 5A/10A Medium Load Control JV Series FEATURES UL, CSA, VDE, SEMKO, CQC recognized UL class B (130 C) wire class Low profile and space saving - Height: 12.5 mm - Mounting
Custody Transfer Measurement. with the V-Cone Flowmeter
Custody Transfer Measurement with the V-Cone Flowmeter Stephen A. Ifft McCrometer Inc. Hemet, California, USA Abstract This paper will discuss the approval of the McCrometer V-Cone flowmeter for custody