Torch Height Control (THC) Manual
|
|
- Kevin Willis
- 7 years ago
- Views:
Transcription
1 Torch Height Control (THC) Manual Cable Wiring Torch to Isolation Box Cable Isolation Box to Controller Cable DB-15 (male) Color 1 + Varc Violet 2 - Varc Blue 5 + Start White 6 OK to start Red 7 Ohmic sensor Blue (outside) 13 - Start Gray 14 OK to start Yellow Minifit Function Color DB 25 4 Ground Black 19 6 Output A- Blue 23 9 Ground/Shield Heat Tube NA 10 Input A White 1 12 Input B Gray V Red 6 15 Output A+ Violet Analog In Yellow 3 Ohmic Sensor Cable (Optional) The Ohmic Sensor Cable is 25 feet long. One end has female quick connect and the other has a male quick connect. 1
2 Setting Up the THC Assembly Plug in THC Cables 1) Set up the Torch Height Control Box (Also called the Isolation Box) Plug in the DB 15 on the torch to Isolation Box cable to the Isolation box. Plug in the DB 25 on the Isolation Box to Controller to the Isolation Box. Plug in the Ohmic Sensor Cable (Optional) male quick connect to the DB 15 female quick connect. Mount the Isolation Box to the Torch Power Supply DB 15 ISOLATION BOX DB 25 2) Plug the connector from the torch to Isolation Box cable into your torch power supply. 2
3 3) Plug in the Mini Fit Molex connector in the Mini I/O slot on the controller 4) Make sure that the Ohmic Sensor Cable is connected to the torch (Optional) 3
4 Preparing Plasma Table for Use 1) Verify that you meet all electrical power requirements, which are defined by the torch. 2) Verify that the air compressor is set up correctly. Is it powerful enough for your needs? Do you need and air filter or air dryer? Does it keep pressure at the recommended range? If not, you may need an additional regulator. 3) Verify that everything is hooked up correctly to the power supply and to the torch. 4) Verify that the power supply settings are correct, which are material dependent. On many torches you can change the amperage, air pressure, and type of cut. 5) It is recommended that an initial test piece is cut when the torch is initially set up to verify that the torch is working properly with our software. The test cut can be cutting a short line along an incline. 4
5 Configuring Flashcut Software to Use THC (Version 4) 1) Install Flashcut Version 4 on your computer 2) Save the CustomVars.txt file to the C drive under ProgramData>FlashCut CNC>FlashCut CNC 4. The picture below shows what the file looks like. Do not change this file. 3) In the configuration screen under Torch Height Control make sure that Use Torch Height Control is checked. Make sure that the touch-off at start is checked if you are using the Ohmic Sensor. Refer to the picture below for the recommended settings. Torch Height Control: References the voltage difference from the tip of the torch to the metal being cut to adjust height Arc Voltage Divisor:? Pierce Height: The initial height of the torch from the material during pierce Cut Height: Constant height of torch during cut Lock Out Factor: % of the programmed feed rate which turns off THC. This feature may improve cuts around corners. Lock Out Hysteresis: After THC has been locked out, this is the amount (feed rate) that needs to change before THC is initiated again. Touch-Off at Start: The torch will touch the metal as a reference first before piercing when using an Ohmic clip. Feed Rate: The feed rate at which the torch seeks the material for Touch-Off. Monitor Input Line: The input line of the Ohmic Sensor Sensing Limit (Z Prog Coord): The distance the torch will move before stopping when seeking the material. 5
6 4) In the configuration I/O Output screen make plasma output line 1. 5) Configure the input line screen as shown below regarding the Ohmic Sensor and OK to Start. Input 19: Function= Control, Description= Ohmic Sensor, Wiring= NC, Debounce= Input 20: Function=Control, Description= OK to Start, Wiring= NO, Debounce= Configure debounce during motion to 115, and debounce when idle to
7 6) Make two M-Codes to Control Output Lines a) M-50: Description= Torch On, Program Line First Action= M-Cd, Delay= 0.5, Ln1= 1 b) M-51: Description= Torch Off, Program Line First Action= M-Cd, Delay= 0, Ln= 0 Make two M-Codes to Execute Macros. Copy the pictures below. a) M-80: Description= Start ATHC b) M-81: Description= Stop ATHC M-80 M-81 7
8 7) Edit the M-Code Execution screen as shown below 8) If you want to use cutter compensation, then make tools in the tool library with the proper kerf diameter depending upon the settings and material you are cutting. Ignore this step if cutter compensation is not being used. 9) You should be ready to cut! 8
9 Z-Axis Lifter Features Features: Fast Anti-Backlash Robust (Works with torch or router) Adjustable torch position Magnetic Breakaway attached to input line sensing for superior torch protection and safety This picture shows the input line hooked up to the magnetic breakaway 9
10 This picture shows the functionality of the magnetic breakaway. 10
PLCM-T1 / PLCM-T2 Torch height controller
www.purelogic.ru Operating guide СОДЕРЖАНИЕ: 1. General information... 2 2. Scope of delivery... 3 3. Specifications... 3 4. The differences between T1 and T2... 4 5. Principle of operation... 6 6. Wiring
More informationVolume PRECISION PLASMA LLC. CNC Plasma Gantry Manufacturer. Plasma Gantry Selection Guide
Volume 1 PRECISION PLASMA LLC CNC Plasma Gantry Manufacturer Plasma Gantry Selection Guide Plasma Gantry Selection Guide Precision Plasma LLC info@precisionplasmallc.com Chapter 1 Mechanical Components
More informationOperation Manual. Plasma torch height controller. Model: Compact THC Controller 150
Operation Manual Plasma torch height controller. Model: Compact THC Controller 150 Notes on safety WHEN THE DEVICE IS IN OPERATION, VOLTAGE HAZARDOUS TO HEALTH AND HUMAN LIFE IS PRESENT INSIDE THE HOUSING
More informationOperating and installation instructions. Professional plasma torch height control. Model: MyPlasm THC
Operating and installation instructions Professional plasma torch height control Model: MyPlasm THC Characteristics of the device: - A miniature casing for panel mounting - Full optical insulation of inputs
More informationSERVICE MANUAL FOR 12 VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOF TOP UNITS ONLY
RV Products Division SERVICE MANUAL FOR 12 VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOF TOP UNITS ONLY Airxcel, Inc. RV Products Division P.O. Box 4020 Wichita, KS 67204 1976A376 (1-11) TABLE OF CONTENTS
More informationControl Box Wiring For PRSstandard Tool
888-680-4466 ShopBotTools.com Control Box Wiring For PRSstandard Tool Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Introduction:...5 Installation:...5
More informationGlobal Motion Technology Inc Web www.motiontek.ca THCSA200. Capacitive sensor plasma & Oxy-fuel Torch Height Control
THCSA200 Capacitive sensor plasma & Oxy-fuel Torch Height Control Features 1) Stand alone controller for THC & OHC completely independent from CNC computer software or CNC control system 2) closed-loop
More informationPLASMA CUTTING MACHINES PL SERIES
PLASMA CUTTING MACHINES PL SERIES PLASMA CUTTING MACHINES Plasma machines offers the best mixed gases quality, efficiency, lower cutting cost and wide range for cutting of mild steel, stainless steel and
More informationUSER MANUAL V5.0 ST100
GPS Vehicle Tracker USER MANUAL V5.0 ST100 Updated on 15 September 2009-1 - Contents 1 Product Overview 3 2 For Your Safety 3 3 ST100 Parameters 3 4 Getting Started 4 4.1 Hardware and Accessories 4 4.2
More informationReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start. Unitec www.startwithunitec.com
ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start Unitec www.startwithunitec.com Proprietary Information and Materials of Unitec, Inc. Such proprietary information and materials
More information5. Tutorial. Starting FlashCut CNC
FlashCut CNC Section 5 Tutorial 259 5. Tutorial Starting FlashCut CNC To start FlashCut CNC, click on the Start button, select Programs, select FlashCut CNC 4, then select the FlashCut CNC 4 icon. A dialog
More informationPROTECH ELECTRICAL CONNECTORS AND CABLE TIES
INDEX ALLIGATOR CLIPS... 7-7 compressor lead sets... 7-7 CONNECTORS BUTT... 7-3 closed... 7-3 ELECTRICAL... 7-2 terminal adapters... 7-2 QUICK CONNECTS... 7-5 7-6 TWIST-ON WIRE... 7-2 HEAT SHRINK TUBING
More informationmaxon motor maxon motor control EPOS Positioning Controller Cable Starting Set Edition June 2006 part number 302287 Positioning Controller
control EPOS Positioning Controller Cable Starting Set Edition June 2006 24/1 part number 302287 Positioning Controller Documentation Cable Starting Set 1 Table of contents 1 Table of contents... 2 2 Table
More informationWHOLESALE DIRECT INC. 5620 WEST 65TH STREET
Auto Pump V 200 100 0 100 Max Rating Vehicle mount compressor ensures truck air brake system is properly pressurized for immediate dispatch from station Pressure switch regulated operation automatically
More informationTable of Contents Getting Started... 3 The Motors... 4 The Control Board... 5 Setting up the Computer with Mach3... 6 Starting up the Equipment...
User Manual Table of Contents Getting Started... 3 The Motors... 4 The Control Board... 5 Setting up the Computer with Mach3... 6 Starting up the Equipment... 12 G-Code Example... 13 2 Getting Started
More informationT-SERIES INDUSTRIAL INCLINOMETER ANALOG INTERFACE
T-SERIES INDUSTRIAL INCLINOMETER ANALOG INTERFACE T-Series industrial inclinometers are compact high performance sensors used to determine inclination in roll and pitch axes with excellent precision and
More informationOperation Manual. Model : Compact THC Controller SD. ( Step / Dir PID generator) A new generation height controller of plasma torach
Operation Manual A new generation height controller of plasma torach Model : Compact THC Controller SD ( Step / Dir PID generator) Notes on safety WHEN THE DEVICE IS IN OPERATION, VOLTAGE HAZARDOUS TO
More informationNew XUY roller sensors
Do you want to simplify the sensor integration in your conveyor systems? New XUY roller sensors for packet, boxes, letters on roller conveyors. Telemecanique Sensor s OsiSense TM XUY photoelectric sensors
More informationInstallation Procedure For 40mm Swept T Enclosure (Blown Fibre Cables)
Installation Procedure For 40mm Swept T Enclosure (Blown Fibre Cables) Description Component Parts & Specialist Tools This procedure is for the installation of the 40mm Swept T enclosure when used in conjunction
More informationThe Do s and Don ts of Pressure Transducers
The Do s and Don ts of Pressure Transducers ABSTRACT When specifying a pressure transducer for a process measurement, a number of items have to be considered. Some of the more important ones are discussed
More informationLocoNet, the Digitrax Difference
LocoNet, the Digitrax Difference LocoNet is Digitrax's method of communication between LocoNet compatible devices on a model railroad layout. LocoNet Compatible devices are designed to work together on
More informationLMU-5000. Hardware and Installation Guide
LMU-5000 Hardware and Installation Guide Plan The Installation Verify Power, Ground and Ignition. Be sure to check each source (power, ground and ignition) to ensure that the proper signaling exists. This
More informationSERVICE MANUAL 12VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOFTOP UNITS ONLY
SERVICE MANUAL 12VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOFTOP UNITS ONLY! WARNING - SHOCK HAZARD! TO PREVENT THE POSSIBILITY OF SEVERE PERSONAL INJURY, DEATH, OR EQUIPMENT DAMAGE DUE TO ELECTRICAL
More informationILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L
An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair
More informationCutMaster 102. 6.04 Major External Replacement Parts
CutMaster 0 6.04 Major External Replacement Parts Item # Qty Description Catalog # Cover with labels 9-08 Base Enclosure Assembly 9-086 Tube, roll handle 9-0 4 Front Panel 9-087 Rear Panel 9-00 4 Art #
More informationhttp://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
More informationModel 201 Wiegand Touchpad Reader Installation Guide
Model 201 Wiegand Touchpad Reader Installation Guide P/N 460353001C 15AUG11 2011 UTC Fire & Security. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without
More informationAn Introduction to CNC Plasma Cutting
Basic Manufacturing Skills Curriculum An Introduction to CNC Plasma Cutting Section 1 Background Information I. Introduction to this Manual...Page 1 II. A Brief History of Manufacturing...Page 2 III. A
More informationJuice Box Stages 1&2 135&335 Installation Guide 5/10/08
Tools Required: 8mm socket or nut driver Small flat head screwdriver Electrical tape, masking tape, or shrink tube Pep talk: Although the install looks daunting at first, once you get the learning curve
More informationPantone Matching System Color Chart PMS Colors Used For Printing
Pantone Matching System Color Chart PMS Colors Used For Printing Use this guide to assist your color selection and specification process. This chart is a reference guide only. Pantone colors on computer
More informationIP DSLAM IDL-2402. Quick Installation Guide
IP DSLAM IDL-2402 Quick Installation Guide Table of Contents Package Contents... 3 Overview... 4 Setup the IDL series IP DSLAM... 5 Safety Instruction... 5 Hardware Installation... 6 WEB Configuration...
More information1247 Norwood Avenue, Itasca, IL 60143 (800) 468-1488 www.dslgroup.com
LED FLEXIBLE LINEAR TAPE -RGB STATIC SERIES -RGB DESCRIPTION -RGB Series is a color changing lighting system. Designers can create light output that can be varied and also programmed to appropriate Pantone
More informationDatasheet of the Easy Servo Motor ES-MH Series
Datasheet of the Easy Servo Motor ES-MH Series High Voltage Stepper Motor with Encoder, 8-20 Nm Version 1.4 http://www.leadshine.com Descriptions Leadshine s ES-MH series easy servo motors, or stepping
More informationTBi Industries. MIG / MAG Welding torches TBi Expert 0. 1
TBi Industries MIG / MAG Welding torches TBi Expert 1 0. 1 CONTENTS. TBi Expert Gas cooled torches TBi 150 Classic Series 60% (10 min.) Mix : 150 A CO 2 : 180 A Ø 0.6-1.0 mm Water cooled torches TBi 240
More informationViZion Installation Guide
ViZion Installation Guide v2.0 1 ViZion Installation Guide Table of Contents Inventory Hardware Setup Understanding Synchronization Cable Begin by taking an inventory of the required equipment DR Unit
More informationLED Wiring and Connections
LED Wiring and Connections A Handbook of How-to Manuals 2009 usledsupply. All Rights Reserved. Index These step by step how to manuals will give you the foundation necessary to use your new LED lights.
More informationRS-232 to TTL Converter Cables SuperDroid Robots 2013 www.superdroidrobots.com
Description: Designed for easy conversion of a RS-232 signals from a computer to TTL signals in order to interface a computer to a microcontroller or similar electronic devices Features: 72-inch in length
More informationOperation Manual. Trans-Flo
Operation Manual Trans-Flo The TRANS-FLO SYSTEM is a standard-output ballast that can be dimmed on most common theatrical SCR dimming systems. The modular design of the TRANS-FLO SYSTEM streamlines set
More informationBill Conkling July 2012
Bill Conkling July 2012 Introduction: For any ham, there are moments that are priceless, like snagging that elusive rare DX station on a deserted island that hasn t been activated in 52 years. And certainly,
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. OMNISTAT 2 (RC-1000 and RC-2000) WIRED MODELS ONLY.
Manufacturer: Model Number(s): Minimum Core Module Version: Comments: HAI Document Revision Date: 4/18/2013 OMNISTAT 2 (RC-1000 and RC-2000) WIRED MODELS ONLY Firmware V. 1.03 Tested Integration Note OVERVIEW
More informationArticle : A-451. RPM amplifyer. Technical card : 20-08-2007 Updated : 21-05-2008
Technical card : 20-08-2007 Updated : 21-05-2008 Article : A-451 RPM amplifyer Application : It is an electronic amp with microprocessor which adapts the RPM signals coming from nearly all types of engines
More informationR22. K Control. Indoor Unit. Nomenclature. Compatibility PL H 3 G K H B. Unit style Heat Pump Horse Power
R22. K Control. Indoor Unit. Nomenclature. PL H 3 G K H B Compatibility Unit style Heat Pump Horse Power Control Boost Heaters R22. K Control. Outdoor Unit. Nomenclature. PU H 3 Y K A Compatibility Outdoor
More informationASSEMBLY MANUAL SE-4S35
Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended
More informationGold Eagle HV Gold Eagle HV Cable Kit (EtherCAT and CAN)
Gold Eagle HV Gold Eagle HV Cable Kit (EtherCAT and CAN) January 2014 (Ver. 1.000) Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information
More informationRoof Top Air Conditioner INSTALLATION AND OPERATING INSTRUCTIONS
Roof Top Air Conditioner INSTALLATION AND OPERATING INSTRUCTIONS Ducted System RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number: Serial Number: Date Purchased: This manual must be read and
More informationDurmazlar has aimed continous development since 1956
Head Quarter & Ataevler Durmazlar has aimed continous development since 1956 Owes one of the world s most contemporary production plants in the production technology business.3 different plants oriented
More informationSystem Wiring Design Guide
877-523-2288 System Wiring Design Guide This guide will help demonstrate the various types of wiring solutions available when connecting video surveillance cameras to Security Camera Agent Security Digital
More informationFigure 1-A This end of the cable is the side that will be plugged into the power adapter and DVR Card.
Follow these steps to properly connect your All-In-One Power and Video Cables to your camera and DVR Card. Required Tools: None A, First, remove the Cable from it s packaging and un-coil it enough to find
More informationINSTALLATION INSTRUCTION Touch Panel Switch with Occupancy Sensor
CAUTION : KEEP FROM HEAT AND METAL SURFACES This product is designed for use indoors with general electronic devices. voltage and current must meet specifications Use certified wires and cables for installation
More informationcs281: Introduction to Computer Systems Lab08 Interrupt Handling and Stepper Motor Controller
cs281: Introduction to Computer Systems Lab08 Interrupt Handling and Stepper Motor Controller Overview The objective of this lab is to introduce ourselves to the Arduino interrupt capabilities and to use
More informationX-Cruiser Series Installation Guide
X-Cruiser Series Installation Guide Verkrijgbaar bij: Grafi-Call Computers BV. Leiden 1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs from Side Panel. pull
More informationVisit us on the web: www.autoshop101.com
This Automotive Series CIRCUIT PROTECTION has been developed by Kevin R. Sullivan Professor of Automotive Technology Skyline College All Rights Reserved Visit us on the web: www.autoshop101.com CIRCUIT
More informationPTU Series Transducer Digital Display Indicator User s Manual
PTU Series Transducer Digital Display Indicator User s Manual The Swagelok PTU series digital display indicator is available to mount directly to the Swagelok PTU series transducer to provide local indication
More informationUser s Manual. BNC Mini-High Res, 75 Ohm Termination Kit Connector Installation Guide (60-073-01)
User s Manual BNC Mini-High Res, 75 Ohm Termination Kit Connector Installation Guide (60-073-01) BNC Termination Kit Instructions This document is a compilation of Extron s instructions, together with
More informationInstalling a Probe. Typical Installation
for hazardous locations. Prior to any installation in a Classified Hazardous Location, verify installation methods by the Control Drawing referenced on the product s name tag 2. The Feed Through Assembly
More informationGold Cello Gold Cello Cable Kit
Gold Cello Gold Cello Cable Kit January 2014 (Ver. 1.101) Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information belonging to Elmo
More informationElectronic Brake Controller Hayes Brake Controller Company ENERGIZE III P/N # 81741B or ENERGIZE XPC P/N #81745 OPERATION MANUAL
Electronic Brake Controller Hayes Brake Controller Company ENERGIZE III P/N # 81741B or ENERGIZE XPC P/N #81745 OPERATION MANUAL ENERGIZE III is for trailers with 2 or 4 electric brakes and vehicles with
More informationGARMIN GPS to PC Wiring Instructions
GARMIN GPS to PC Wiring Instructions Introduction This will outline the basics for connecting most GARMIN GPS receivers to a PC serial connector for data transfer. Since the GPS needs to both send and
More informationSystem Wiring Design Guide
System Wiring Design Guide This guide will help demonstrate the various types of wiring solutions available when connecting video surveillance cameras to EZ Watch Pro and Armor Pro Digital Video Recorders.
More informationK8025 VIDEO PATTERN GENERATOR. Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting.
K8025 ILLUSTRATED ASSEMBLY MANUAL H8025IP 1 VIDEO PATTERN GENERATOR Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting. Forum Participate our Velleman Projects Forum
More informationInstruction Sheet ACS-101. General Description. Specifications. Amplified Broadband UHF Combiner-Splitter. Overall. Antenna Splitter.
ACS-101 Amplified Broadband UHF Combiner-Splitter General Description The ACS-101 (Antenna Combiner Splitter 10 to 1) is an amplified and filtered broadband splitter-combiner. It allows up to 10 base stations
More informationPower Supply and Cabling Options. SmartTrak 100/101/140
Power Supply and Cabling Options SmartTrak 00/0/40 2 Power Supply and Cabling Options SmartTrak 00/0/40 Table of Contents Power Supplies... Communication Cables... Accessory Options... Appendix A Communication
More informationPUSH BUTTON START INSTALLATION MANUAL
PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.
More informationGTR-128/GTR-129 Motorcycle/ Vehicle Tracker Quick Start Guide
GTR-128/GTR-129 Motorcycle/ Vehicle Tracker Quick Start Guide GlobalSat WorldCom Corporation 16F., No. 186, Jian 1 st Rd, Zhonghe Dist., New Taipei City 23553, Taiwan Tel: 886.2.8226.3799/ Fax: 886.2.8226.3899
More informationBuilding A Computer: A Beginners Guide
Building A Computer: A Beginners Guide Mr. Marty Brandl The following was written to help an individual setup a Pentium 133 system using an ASUS P/I- P55T2P4 motherboard. The tutorial includes the installation
More informationStop Alert Flasher with G-Force sensor
Stop Alert Flasher with G-Force sensor Stop Alert module creates brake light flashing effect to catch attention of the drivers behind to avoid dangerous rear end collision. The flasher module is a state
More informationECR Shelf System Installation Guide Centralized Rack Mount Call Recording
Hardware & Installation Guide Algo Communication Products Ltd. Customer Support and Sales Tel: 1.877.884.2546 Fax: 604.437.5726 Email: sales@algosolutions.com support@algosolutions.com www.algosolutions.com
More informationDatasheet of the Easy Servo Motor ES-M Series
Datasheet of the Easy Servo Motor ES-M Series Stepper Motor with Encoder, 0.9-8 Nm Version 1.3 http://www.leadshine.com Descriptions Leadshine s ES-M series easy servo motors, or stepper motors with encoders,
More informationCisco T1 Layer 1 Troubleshooting
Table of Contents T1 Layer 1 Troubleshooting...1 Introduction...1 Troubleshooting with the show controller t1 Command...1 Related Information...3 i T1 Layer 1 Troubleshooting Introduction Troubleshooting
More informationMachine-side reference guide
Machine-side reference guide 803640 Plasma Plasma: the fourth state of matter The first three states of matter are solid, liquid and gas. For the most commonly known substance water these states are ice,
More informationpicopsu-90-xlp 12V, 90Watt ATX Power Supply Quick Installation Guide Version 1.0a P/N picopsu-90-xlp
picopsu-90-xlp 12V, 90Watt ATX Power Supply Quick Installation Guide Version 1.0a P/N picopsu-90-xlp Introduction Based on the electrical design of the picopsu-90, the picopsu-90-xlp is a small yet powerful
More informationSYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODEL CHCRV-5 For Use with Bard CH Series 3, 4 & 5 Ton 2-Stage Wall Mount Heat Pumps AND W38H, W43H, W49H and W61H Single Stage Wall Mount
More informationEVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board.
EVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board. This Troubleshooting Guide covers the electric coolant valve and control
More informationFading Red Tones on Color LaserJet 2600s
Procedures Fading Red Tones on Color LaserJet 2600s HP Color LaserJets 2600n, 1600, and 2605 share the same basic Canon engine design. One aspect of the design brings the common problem of scanner optic
More informationDigi-Motor Installation Guide
Digi-Motor Installation Guide Installation Video...located at marsdelivers.com Digi-Motor Installation Guide Digi-Motor For technical assistance with your Azure Digi-Motor, call the MARS technical support
More informationOEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE
OEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE Scaletron Industries, Ltd. Bedminster Industrial Park 53 Apple Tree Lane P.O. Box 365 Plumsteadville, PA 18949 USA Toll Free: 1-800-257-5911 (USA &
More informationMaking a DB to RJ45 adapter.
Making a DB to RJ45 adapter. DB9 to RJ45 adapters are often used in combination with a RS232 repeater for extending the distance of a serial RS232 link, but can be used for any adapter or converter purposes.
More informationABB Drives. User s Manual HTL Encoder Interface FEN-31
ABB Drives User s Manual HTL Encoder Interface FEN-31 HTL Encoder Interface FEN-31 User s Manual 3AUA0000031044 Rev B EN EFFECTIVE: 2010-04-06 2010 ABB Oy. All Rights Reserved. 5 Safety instructions
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationElectronic Pressure Switch EDS 300
Electronic Pressure Switch EDS 300 User manual Page 2 of 16 Content 1. Functions of the EDS 300...3 2. Mounting...3 3. Operating keys on the membrane keypad...4 4. Digital display...4 5. Output function...5
More informationDCP Fan Controller. Version 01/2009. The engineer s choice
Version 01/2009 The engineer s choice Index Page 1. Introduction... 3 2. Technical specification... 4 3. Connection diagrams... 9 4. Configuration... 10 5. Compatible ebm-papst Fan List... 11 2 1. Introduction
More informationRS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
More informationIMMS-CCC. IMMS-CCC Hardwire Central Interface. Installation Instructions
IMMS-CCC IMMS-CCC Hardwire Central Interface Installation Instructions TABLE OF CONTENTS... Choose a Location... 1 Connections... 2 Operations... 3 Software Configuration... 4 Troubleshooting... 5 Loopback
More informationJNIOR. Overview. Get Connected. Get Results. JNIOR Model 310. JNIOR Model 312. JNIOR Model 314. JNIOR Model 410
The INTEG is an Ethernet I/O (digital, analog) device that monitors and controls a small set of process signals. functions as both basic I/O for integration with another application or system AND as a
More informationMirror Mount Video Monitor/Recorder with Front and Rear View Night Cameras PLCMDVR5
Mirror Mount Video Monitor/Recorder with Front and Rear View Night Cameras PLCMDVR5 www.pyleaudio.com Instruction Manual Installation and Connection: 1. Please disconnect your car battery. 2. In the contents
More informationApplied Electronics. Commercial Dimming System UPDATE NOTICE
REV. A Applied Electronics Commercial Dimming System UPDATE NOTICE This notice is to inform the end user of an additional feature added to this DP12/2400 dimming unit. This unit has been outfitted with
More informationLynx Broadband Installation Manual for Residential Packages with a 20 db Amp Quick Start Guide (first two pages)
Lynx Broadband Installation Manual for Residential Packages with a 20 db Amp Quick Start Guide (first two pages) 1. Be sure that your kit includes all the parts shown in the Check the Equipment section
More informationMy Touch-CAM Ford Rear-Camera integration kit for 8.4 My-Touch Radios NTV-KIT391/392/446/456
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 My Touch-CAM Ford Rear-Camera integration kit for 8.4 My-Touch Radios NTV-KIT391/392/446/456 BHM Overview The My Touch CAM
More information5-Other arc welding WELDING TOOLS AND ACCESSORIES
WELDING TOOLS AND ACCESSORIES -Other arc welding ARC WELDING OTHER Cables and connectors... 80 to 81 Clamps... 82 to 83 Magnetic ground clamps... 84 to 8 Hammers / brushes... 86 Miscellaneous... 87 Accessories...
More information2002-2003 Kawasaki Vulcan 1500 Mean Streak Installation Instructions
Parts List 1 Power Commander 1 CD-ROM 1 Installation Guide 1 Wire Tap Connector 2 Power Commander Decals 2 Dynojet Decals 1 Velcro Strip 1 Alcohol Swab 2002-2003 Kawasaki Vulcan 1500 Mean Streak Installation
More information22.302 Experiment 5. Strain Gage Measurements
22.302 Experiment 5 Strain Gage Measurements Introduction The design of components for many engineering systems is based on the application of theoretical models. The accuracy of these models can be verified
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationsensors Miniature Sensors - S100 The universal miniature photoelectric sensor
Miniature Sensors - S1 The universal miniature photoelectric sensor Two threaded front mounting holes Two slotted rear mounting holes Anti-tampering sensor (no adjustment) Standard optic functions and
More informationMagnetic field sensor for pneumatic cylinders BIM-INT-Y1X-H1141
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Rectangular, height 6mm Plastic, PA12 Magnetic-inductive sensor DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6
More informationLighting Controls ! WARNING RISK OF ELECTRIC SHOCK. Installation Instructions DESCRIPTION
GE Lighting Installation Instructions Lighting Controls Centralized Lighting Control Panel Interior Catalog Number CLCINTxx DESCRIPTION The Centralized Lighting Control System is a small network of relay
More informationTriac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
More informationExternal temperature sensors for FSC Ultrasonic Flow Meter (thermal flow measurement function)
Application: Heat quantity measurement This function calculates the heat quantity received and sent with liquid (water) in cooling and heating. Two 4-20mA inputs are available for temperature measurements.
More informationAVR 158. Audio/video receiver. Quick-Start Guide ENGLISH
158 Audio/video receiver ENGLISH Quick-Start Guide 158 Introduction, Speaker Placement and Connection Introduction Thank you for choosing a harman kardon product! This quick-start guide contains all the
More informationModels SFP33 & SFP32 Pressure Transmitters
SFP33 Flow-Through Pressure Transmitter SFP32 Single-Ended Pressure Transmitter DS-PR-SFP-eng April, 2016 Data Sheet Models SFP33 & SFP32 Pressure Transmitters Pressure Brooks Seal Free Pressure Measurement
More information