3-Wire Wallbox Adapter For Seeburg SMC jukeboxes with the GEN2 MCU

Size: px

Start display at page:

Download "3-Wire Wallbox Adapter For Seeburg SMC jukeboxes with the GEN2 MCU"

Rodney Richardson
7 years ago
Views:

1 3-Wire Wallbox Adapter For Seeburg SMC jukeboxes with the GEN2 MCU Connect any 3-wire wallbox selector to your Seeburg SMC jukebox Requires the 'GEN2' Microcomputer Control Unit AMI W-40 AMI W-80 AMI W-120 AMI WQ-200 Rock-Ola 500 Rock-Ola 503 Rock-Ola 1555 Rock-Ola 1558 Rowe WRA Rowe WRB Rowe WRC Seeburg 3W1 Seeburg 3W100 Seeburg 3WA Seeburg SC1-4 Seeburg SCH1-4 Wurlitzer 3020 Wurlitzer 5207 Wurlitzer 5210 Wurlitzer 5220 Wurlitzer 5225 Wurlitzer 5250 ORDER PART # SMC-WB5 for 50Hz version WALLBOX MODEL SETUP Move the SERVICE SWITCH on the CPA panel to SERVICE MODE. The display will show SCE and the current 2-digit record position number. While holding the CREDIT switch on, press digit 4 for GENERAL SETUP. Use the Left or Right RESET key and get to the rse setting (Remote Selector type). From the list below, enter the 1 or 2 digit wallbox model code. Move the SERVICE SWITCH back to NORMAL PLAY MODE. rse WALLBOX MODEL Max Sel Seq Type 0 Seeburg digital DEC (requires the blue box DMT1, DEC-MCU TRANSLATOR) Seeburg Consolette SC1/2/3/4, SCH1/2/3/4 160 Letter 2 Wurlitzer 5210, 5220, Number 3 Seeburg Wall-O-Matic 3W1, 3W Number 4 Seeburg Wall-O-Matic 3WA 160 Letter 5 Rowe WRA, WRB, WRC 160 Letter 6 AMI W-40, W-80, W-120, WQ Button 7 Wurlitzer Button 8 Wurlitzer Number 9 Wurlitzer Button 10 Rock-Ola 500, 1555, 1558 (and most other models) 160 Button Data Sync Engineering P.O. Box 539, 2 Footbridge Lane Blairstown, New Jersey TEL: (908) FAX: (908) Copyright 2010 Data Sync Engineering. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.

Wurlitzer 5210 Wurlitzer 5220 Wurlitzer 5225 Wurlitzer 5250 ORDER PART # SMC-WB5 for 50Hz version WALLBOX MODEL SETUP Move the SERVICE SWITCH on the CPA panel to SERVICE MODE.

2 WALLBOX SYSTEM WIRING WALLBOX SELECTOR WALLBOX ADAPTER J2 SIG SMC-WB 3-Wire Wallbox Adapter for GEN2 Seeburg SMC MCU COM WALLBOX POWER NOT SUPPLIED But required to power wallbox (YELLOW) (YELLOW) SEEBURG SMC MCU GEN2 ADAPTER INSTALLATION In-line fuse holder with 1A fuse Black wire is not used. Apply tape or wire nut. POWER TRANSFORMER VAC, 2 Amps Radio Shack or equivalent Insert the 9-pin connector to the J2 position on the GEN2 MCU board. The 2-wire zipcord receives the signal from the wallbox. You can extend the length of the wallbox signal wires, using 22AWG, to a distance of up to 2,000 feet (609.6 meters). The wallbox signal is and has no specific wire polarity. You will need a Volt, 2 Amp power transformer to power the wallbox Locate your wallbox model in the following pages for wiring detail. TECH NOTE Electrical pulses transmitted by the wallbox are generated by a contact arm rotating on a selector disc containing contact points. When these contacts become gummed up and corroded, the wallbox may not make the proper selection. Occasionally, these contacts require cleaning. They can be cleaned with a cloth saturated with isopropyl alcohol. Do not use emery cloth or sandpaper as this may remove the plating. On really worn wallboxes, where basic cleaning doesn t seem to cure the problem, you may have successful results by using a low abrasive polish, such as Scratch Out or Brasso. This will make the contact surfaces shiny and smooth.

POWER TRANSFORMER 25-30 VAC, 2 Amps Radio Shack 273-1512 or equivalent Insert the 9-pin connector to the J2 position on the GEN2 MCU board. The 2-wire zipcord receives the signal from the wallbox.

3 NBR LTR SEL REC A1 A2 A3 A4 A5 A6 A7 A8 A9 A0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D0 E1 E2 E3 E4 E5 E6 E7 E8 E9 E0 A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 Q1 R1 S1 T1 U1 V1 A2 B2 C2 D2 E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 Q2 R2 S2 T2 U2 V2 A3 B3 C3 D3 E3 F3 G3 H3 J3 K NBR LTR SEL REC F1 F2 F3 F4 F5 F6 F7 F8 F9 F0 G1 G2 G3 G4 G5 G6 G7 G8 G9 G0 H1 H2 H3 H4 H5 H6 H7 H8 H9 H0 J1 J2 J3 J4 J5 J6 J7 J8 J9 J0 K1 K2 K3 K4 K5 K6 K7 K8 K9 K0 L3 M3 N3 P3 Q3 R3 S3 T3 U3 V3 A4 B4 C4 D4 E4 F4 G4 H4 J4 K4 L4 M4 N4 P4 Q4 R4 S4 T4 U4 V4 A5 B5 C5 D5 E5 F5 G5 H5 J5 K5 L5 M5 N5 P5 Q5 R5 S5 T5 U5 V NBR LTR SEL REC L1 L2 L3 L4 L5 L6 L7 L8 L9 L0 M1 M2 M3 M4 M5 M6 M7 M8 M9 M0 N1 N2 N3 N4 N5 N6 N7 N8 N9 N0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q0 A6 B6 C6 D6 E6 F6 G6 H6 J6 K6 L6 M6 N6 P6 Q6 R6 S6 T6 U6 V6 A7 B7 C7 D7 E7 F7 G7 H7 J7 K7 L7 M7 N7 P7 Q7 R7 S7 T7 U7 V7 A8 B8 C8 D8 E8 F8 G8 H8 J8 K NBR LTR SEL REC R1 R2 R3 R4 R5 R6 R7 R8 R9 R0 L8 M8 N8 P8 Q8 R8 S8 T8 U8 V SEQUENCED NUMBER SEQUENCED LETTER SELECTION BUTTON RECORD SELECTED WALLBOX TRANSLATION CHART

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 200 101 201 102 202 103 203 104 204 105 205 106 206 107 207 108 208 109 209 110 210 111 211 112 212 113 213 114 214 115 215 116 216 117

4 Wallbox Wiring Diagrams CAUTION: Do not attempt to hook up a wallbox power supply if you are not familiar with electrical wiring, consult with a qualified person or an electrician. Do not leave any wires exposed, always use wire-nuts or electrical tape on all connections. Improper wiring can result in a fire or shock hazard. Seeburg Wall-o-matic 3W1 / 3W select Seeburg Wall-o-matic 3WA

Do not leave any wires exposed, always use wire-nuts or electrical tape on all connections.

5 Seeburg Consolette SC1-4 / SCH select BLK WHT BLU To enable coin operation, the BRN / RED / ORG terminals must be shorted together and connected to the terminal (WHT) using a Ohm, 10 Watt power resistor (solenoid current = 400mA). Wurlitzer 5220 Wurlitzer select 3 G 1

connected to the terminal (WHT) using a 40-50 Ohm, 10 Watt power

6 Wurlitzer select AMI W-40 / W-80 / W / 80 / 120 select Rowe WRA / WRB / WRC * A wire jumper must be inserted from the main power terminal (#2) to the * keypad motor terminal (#4).

7 Wurlitzer 5210 Wurlitzer 5250 Rock-Ola 1555 Rock-Ola select Rock-Ola select

8 Wurlitzer select The Original 1015 Bubbler Wallbox 120VAC This wallbox has its own built-in transformer and requires a 120VAC power cord. High voltage is used so be very careful when wiring up this wallbox. The wallbox adapter only requires the two wire connection to terminal #1 and terminal #3. AMI WQ-200 * A wire jumper must be inserted from the main power terminal to the * lock-out.

High voltage is used so be very careful when wiring up this wallbox.

PUSH BUTTON START INSTALLATION MANUAL

PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.