POWER TRIM 5 F AUTO TRIM AND AUTO TRIM
|
|
- Dwain Long
- 7 years ago
- Views:
Transcription
1 POWER TRIM 5 F AUTO TRIM AND AUTO TRIM
2 Table of Contents Page Auto Trim System F-1 Description F-1 Auto Trim Operation F-2 Electrical System Overload Protection F-4 Auto Trim Limit Adjustment F-4 Control Module Adjustment F-6 Trim Position Indicator Adjustment F-6 5F-0 - AUTO TRIM AND AUTO TRIM II
3 Auto Trim System Description NOTE: The only difference between AUTO TRIM and AUTO TRIM Il, is that AUTO TRIM II has an Adjustment Knob on the Control Module. The Auto Trim System consists of the following major components: Auto Trim Pump same pump that is used on the standard Power Trim models. Control Module a solid-state electronic device that senses engine RPM and regulates the time at which the drive unit trims In and Out when operating in the AUTO mode. Module is protected by a 20-amp fuse. Mode Switch allows the operator to select either AUTO or MANUAL trim operation from the dash. Manual Trim Control will only function with mode switch in the MANUAL mode and ignition switch in the RUN position. Allows the operator to raise and lower the drive unit for trailering, beaching, launching and shallow water operation. Also, allows the operator to manually adjust the drive unit trim angle while underway in situations where automatic trimming is not desired (rough seas, etc.). Trim Limit Switch Establishes the maximum trim Out limit in both the MANUAL and AUTO mode. Prevents drive unit from moving out of the gimbal ring support flanges, which could cause possible damage to stern drive if it were to occur at higher engine speeds. POWER TRIM BLK Black BLU Blue BRN Brown GRY Gray GRN Green ORN Orange PNK Pink PUR Purple RED Red TAN Tan WHT White YEL Yellow LIT Light DRK Dark AUTO TRIM II SYSTEM WIRING DIAGRAM AUTO TRIM AND AUTO TRIM II - 5F-1
4 Auto Trim Operation The Auto Trim system is designed to allow either automatic or manual trimming of the boat while underway in addition to allowing drive unit to be raised for trailering, beaching, launching or shallow water operation. A 2-position switch on dashboard allows the operator to select the mode desired. Boat Running Above Planing Speed Auto Trim Mode Switch AUTO MODE OPERATION 22217! WARNING Drive unit will automatically lower from the raised position when the ignition switch is turned to the RUN position and mode switch is placed in the AUTO mode. BE SURE THAT NO ONE IS IN THE AREA OF THE DRIVE UNIT. With mode switch in the AUTO mode, the drive unit will move automatically to properly trim boat while underway. This allows boat operator to keep both hands on the steering wheel and to direct operator s full attention to drive the boat. At engine speeds below 3100 RPM, the drive unit will remain in the full In position. This will force the bow of the boat down and help it get up on plane quickly. Once engine reaches 3100 RPM and after a 5-6 second delay (to ensure that boat is up on plane), the drive unit will automatically trim Out to a preset position for maximum boat speed and efficiency. Trim Out position can be adjusted to fine tune the trim angle for each individual boat. Upon deceleration, the drive unit will trim In when engine reaches 2600 RPM. Most boats will still be up on plane at this point. After drive reaches full In position, the trim pump motor will continue to run for approximately 5 seconds. NOTE: The AUTO mode also can be used to lower the drive unit from the fully raised (trailering) position. By placing ignition switch in RUN position and mode switch in AUTO mode, the drive unit will automatically lower to the full In position. Be sure that no one is in the area of the drive unit. Boat Running Below Planing Speed MANUAL MODE OPERATION Placing the mode switch in the MANUAL position will deactivate the AUTO system and allow the operator to adjust drive unit position, using the manual trim control. Typical controls are shown following. Manual trimming may be desirable to fine tune the trim angle for a particular water condition or boat load, or in situations where greater control over the trim operation is needed. Manual trim control also must be used to raise the drive unit for trailering, beaching, launching and shallow water operation. Ignition switch must be in the RUN position for manual trim control to function. 1. RAISING DRIVE UNIT. a - Up / Out Button b - Up Button Press Until Drive Unit Reaches Desired Height or End of Upward Travel Quicksilver 3-Button Trim Control Panel 5F-2 - AUTO TRIM AND AUTO TRIM II
5 2. TRIMMING DRIVE UNIT OUT (BOW UP ). Press switch until drive unit moves to properly trim boat or trim limit switch stops outward travel Quicksilver Commander Panel Trim Control a - Trailer Switch Press Until Drive Unit Reaches Desired Height or End of Upward Travel NOTE: Some Power Trim pump motors are protected from overheating by an internal circuit breaker. If trailering switch(es) are held depressed after drive unit reaches end of upward travel, internal circuit breaker will open and pump will stop. If this should happen, release switch(es) and allow motor to cool for approximately 2 minutes. Once motor is cool, circuit breaker will reset automatically, and trim operation may be resumed.! CAUTION DO NOT run engine above idle RPM with unit raised for shallow water operation, as drive unit is out beyond gimbal ring support flanges and has no side support. USE EXTREME CAUTION WHEN OPERATING BOAT WITH DRIVE UNIT RAISED. Quicksilver 3-Button Trim Control Panel a - Up / 0ut Button Press Quicksilver Commander Panel Trim Control a - Trim Switch Press Up on Switch AUTO TRIM AND AUTO TRIM II - 5F-3
6 ! CAUTION NEVER trim the drive unit Out using the Trailer switch(es) while boat is underway. Severe damage to drive unit may result if the unit is raised beyond the gimbal ring support flanges at engine speeds above idle RPM. 3. TRIMMING DRIVE UNIT IN (BOW DOWN ) Press switch until drive unit moves to properly trim boat or until drive unit reaches end of downward travel. Electrical System Overload Protection The Auto Trim electrical system is protected from overload by a 110-amp fuse, and a 20-amp in-line fuse at control module positive (+) battery lead and a 20-amp in-line fuse at ignition switch (if Quicksilver ignition switch is used). If boat is equipped with 3-Button Control Panel, a 20-amp in-line fuse also is located at panel. If Auto Trim electrical system becomes inoperative, check for a blown fuse. If fuse has blown, the cause for overload MUST BE found and corrected BEFORE replacing fuse. Auto Trim Limit Adjustment In most cases, best all-around performance is obtained with drive unit adjusted so that front of hull will be slightly out of water when boat is on plane. Quicksilver 3-Button Trim Control Panel a - In Button Press Boat Properly Trimmed Adjusting the drive unit Out from this position will tend to raise the bow of the boat, thus further reducing the wetted surface of the hull and, in some cases, increasing boat speed. However, if trimmed out excessively, bouncing, porpoising, propeller ventilation and possible difficult steering control could result. Bow Too High Move Drive Unit In Quicksilver Commander Panel Trim Control a - Trim Switch Press Down on Switch 5F-4 - AUTO TRIM AND AUTO TRIM II
7 Adjusting the drive unit In from normal position will force the bow of the boat down, thus increasing the wetted surface of the hull and, in some cases, improving boat ride in rough water (at partial throttle). However, this will reduce boat speed in most cases. 3. Place Auto Trim mode switch in the MANUAL mode; turn ignition key to the RUN position. Bow Too Low Move Drive Unit Out ADJUSTING DRIVE UNIT TRIM ANGLE! WARNING When adjusting trim limit, following, use extreme care that engine is not accidentally started and keep clear of area near propeller. Also, use care to prevent placing hands in an area where they could be injured by drive unit movement. a - Mode Switch Place in MANUAL Mode 22217! CAUTION Trim limit switch MUST BE adjusted exactly as stated following. If switch is adjusted incorrectly, drive unit may move out beyond the gimbal ring support flanges (when making test run following), and severe damage to stern drive unit may result. If more trim Out capability is desired, perform the following. 1. Place drive unit in the full In / Down position. 2. Turn trim limit switch clockwise to end of slots. 4. With the assistance of another person actuate manual trim control switch used to trim drive unit Out (DO NOT use Trailer switch) and turn trim limit switch SLOWLY counterclockwise until trim cylinders extend to dimension shown. Retighten trim limit switch retaining screws. a /4 in. 1/4 in. (554mm 6mm) a - Trim Limit Switch b - Retaining Screws Loosen c - Adjusting Slots AUTO TRIM AND AUTO TRIM II - 5F-5
8 5. Turn ignition key OFF. 6. Run boat along a relatively smooth stretch of water and trim boat with manual trim control until optimum boat performance is achieved. 7. After finding trim angle that provides best performance, stop engine (without changing drive unit trim angle). Accurately measure distance between trim cylinder end cap and pivot end. 8. Place drive unit in the full In position. Loosen trim limit switch retaining screws and turn switch clock-wise to end of slots. Control Module Adjustment (Auto Trim Il Only) 1. Turn adjustment knob on control module full counterclockwise. 2. Rotate knob clockwise four clicks (notches). 3. With mode switch in AUTO position and the drive unit trimmed full in, accelerate boat slowly while watching trim gauge. 4. If boat is on plane well before drive unit begins to trim out (this may happen with lighter, faster boats), rotate adjustment knob counterclockwise one click and accelerate boat slowly. Continue procedure until boat is on plane approximately five or six seconds before trim out occurs. 5. If boat is not on plane before drive unit begins to trim out (this may happen with slower, heavier boats), rotate adjustment knob clockwise one click and accelerate boat slowly a - Trim Limit Switch b - Trim Limit Switch Retaining Screws c - Adjusting Slots 9. Leaving Auto trim mode switch in the MANUAL mode, turn ignition key to RUN position. With the assistance of another person, actuate manual trim control switch used to trim drive unit Out and turn trim limit switch slowly counterclockwise until trim cylinders extend to dimension recorded in STEP 7. Tighten switch retaining screws securely. 10. Run boat with Auto Trim mode switch in AUTO position at several speeds, through turns under various water and load conditions, If boat does not perform to satisfaction, repeat adjusting procedure. a - Adjustment Knob Trim Position Indicator Adjustment With ignition key in the RUN position, check Auto Trim indicator to make sure that needle points to bottom of the scale when drive unit is fully IN. If needle is not at bottom of scale, perform steps following.! WARNING Difficulties in handling and operational control may result if drive unit is adjusted Out too far. If difficulties are encountered, drive unit trim angle MUST BE moved In the amount necessary to eliminate the problem and avoid a possible safety hazard a - Needle at Bottom of Scale Drive Unit in Fully In Position 5F-6 - AUTO TRIM AND AUTO TRIM II
9 ! CAUTION While performing this adjustment, use extreme care that engine is not accidentally started and keep clear area near propeller. 1. Turn ignition key to RUN position. 2. Loosen trim position sender retaining screws. 3. Rotate sender, as required, to position indicator at bottom of scale. 4. Tighten retaining screws securely. 5. Recheck instrument reading and turn ignition key to OFF position. a - Retaining Screws b - Turn to Adjust AUTO TRIM AND AUTO TRIM II - 5F-7
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationLeft Hand Limit Switch. Housing. Left Hand. Connections. Motor Connector BROWN PURPLE GRAY BLACK DARK BLUE BLACK BROWN BROWN LIGHT BLUE.
LIGHT BLUE GRAY PURPLE Circuit Breaker Intput Circuit Breaker Output #1 Relay Left Hand Limit Switch Housing Left Hand Motor Connector Right Hand Limit Switch on Radiator Support Right Hand Limit Switch
More informationThis file is available for free download at http://www.iluvmyrx7.com
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationACS R/RP Attitude Control System
ACS R/RP Attitude Control System User s manual Mente Marine Vaasa, Finland info@mente-marine.com www.mente-marine.com Contents Introduction...3 Symbols and abbreviations...3 Security...3 Product disposal...3
More informationRead This Before Operating The BaseHit
Read This Before Operating The BaseHit IMPORTANT OPERATING INSTRUCTIONS THE ACCURACY OF THE BASEHIT PITCHING MACHINE DEPENDS ON THE QUALITY, HARDNESS AND TYPE OF BALLS USED WITH THIS PRODUCT! TREND SPORTS
More informationElectronic Power Control
Service. Self-Study Programme 210 Electronic Power Control Design and Function With the Electronic Power Control system, the throttle valve is actuated only by an electric motor. This eliminates the need
More informationZAPPY 3 OWNER S MANUAL. Read this manual completely before riding your Electric ZAPPY 3.
ZAPPY 3 OWNER S MANUAL Read this manual completely before riding your Electric ZAPPY 3. TECHNICAL INFORMATION Model No. : ZAPPY 3 Product size Type of motor Motor power Battery type Battery Charger Charging
More informationACS ic Attitude Correction System User s manual
ACS ic Attitude Correction System User s manual Mente Marine P.O. Box 472 FIN-65101 Vaasa, Finland Email: info@mente-marine.com www.mente-marine.com Copyright Mente Marine Contents INTRODUCTION... 3 SYMBOLS
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationInstallation & User Manual Radio Remote rev1.0.3
EN Installation & User Manual Radio Remote rev1.0.3 RC-20E RC-21E RC-22E RC-23E SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 www.side-power.com sidepower@sleipner.no
More informationIntroduction. Drenth Motorsport Gearboxes Fleuweweg 10 7468 AG Enter The Netherlands Phone: +31 (0)547 38 26 96 Fax: +31 (0)547 38 20 65
25.03.0023 Introduction The display comes with a software application. With the software application information shown on the display can be adjusted. There are different modes to adjust: the shape of
More informationDENTAL CHAIR AND UNIT SP- CIELA IMPORTANT
DENTAL CHAIR AND UNIT SP- CIELA OPERATING MANUAL IMPORTANT This manual provides operating instruction for BELMONT SP-CIELA. The instructions contained in this booklet should be thoroughly read and understood
More informationELECTRICAL. Table of Contents. Section 2D Wiring Diagrams. Troll Control... 2D-39
Table of Contents Warning System Signals................. 2D-2 Guardian Protection System.............. 2D-3 Guardian System Operation with Gauges 2D-3 Guardian System Activation........... 2D-3 Analog
More information1955-1956 Chevy Bel-Era
Classic Instruments 1955-1956 Chevy Bel-Era Installation Manual Revised January 2, 2014 Page 1 Table of Contents Table of Contents 2 Welcome to the Team of Classic Instruments! 3 55-56 Chevy Part Identification
More informationINSTRUCTION MANUAL. Specification: collective pitch 3D quadcopter. TYPE: Collective Pitch Electric 3D Quadcopter. Rotor Diameter: 118MM.
collective pitch 3D quadcopter INSTRUCTION MANUAL Specification: TYPE: Collective Pitch Electric 3D Quadcopter Rotor Diameter: 118MM Length:635 MM Width: 365 MM Weight: 986g w/out battery Flying weight
More informationThe Black Box Push Button Control Box
Roll Rite, LLC and its entire staff would like to not only Thank You but congratulate you on your purchase of one of what we feel to be the finest line of tarping systems in the industry. The Black Box
More informationINSTRUCTION MANUAL FOR RECREATIONAL REFRIGERATOR/FREEZER MODEL
INSTRUCTION MANUAL FOR RECREATIONAL REFRIGERATOR/FREEZER MODEL 15-LITER, 20-LITER, 35-LITER, 45-LITER, 60-LITER & 100-LITER SECTION 1 Basic Operation SECTION 2 Cleaning and Storing SECTION 3 Basic Trouble
More informationSP AF 300mm F/2.8 LD [IF] for Canon (Model 360EE)
SP AF 300mm F/2.8 LD [IF] for Canon (Model 360EE) We greatly appreciate your purchase of this Tamron lens. The Tamron SP AF 300mm F/2.8 LD [IF] is a fast telephoto lens developed for Canon AF single-reflex
More informationLED MOTION ACTIVATED FLOOD LIGHT
Utilitech & UT Design are registered trademarks of LF, LLC. All Rights Reserved. ITEM #0611551, #0611550 LED MOTION ACTIVATED FLOOD LIGHT MODEL #SE1036-BP2-02LF0-U, SE1036-WH3-02LF0-U Français p. 10 Español
More information12 Volt 30 Amp Digital Solar Charge Controller
12 Volt 30 Amp Digital Solar Charge Controller User s Manual WARNING Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationEVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board.
EVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board. This Troubleshooting Guide covers the electric coolant valve and control
More informationPUSH BUTTON START INSTALLATION MANUAL
PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.
More informationModel SETR-50 and SETR-51 Trim Tab Control
Model SETR-50 and SETR-51 Trim Tab Control Pictured above is the SETR-50 with black switches on a gray background. The SETR-51 is identical except for the color, wherein it has black switches on a black
More informationSERVICE MANUAL HWH COMPUTER-CONTROLLED HYDRAULIC LEVELING SYSTEM 400 SERIES. FEATURING: Paddle Switch Control AUTOMATIC LEVELING AUTOMATIC RETRACT
HWH CORPORATION R SERVICE MANUAL HWH COMPUTER-CONTROLLED HYDRAULIC SYSTEM 400 SERIES R FEATURING: Paddle Switch Control ON LOW EMERGENCY CAUTION! BLOCK FRAME SECURELY BEFORE CHANGING TIRES OR WORKING UNDER
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationVS Commodore LPG installation utilising an LPG Memcal and Apexus Quick-kit.
VS Commodore LPG installation utilising an LPG Memcal and Apexus Quick-kit. Description of the components and operation LPG/Petrol changeover switch The LPG change-over switch is mounted in the instrument
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Vacuum Pump Kit 28146 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully follow these instructions
More informationSTEERING COLUMN CONTROLS
STEERING COLUMN CONTROLS Ignition Switch... 2-1 Lighting/Turn Signal Control Lever... 2-5 Windshield Wiper and Washer Lever... 2-6 Rear Window WiperlWasher Switch (if equipped)... 2-8 Tilt Steering Lock
More informationJANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator
JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator The Janus Pantheon mini operator does not typically require the provision of any additional site requirements other than
More informationLivorsi DTS Controls Single/Dual Engine Digital Throttle & Shift Installation
715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2415 E: info@livorsi.com Livorsi DTS Controls Single/Dual Engine Digital Throttle & Shift Installation NOTICE This document is written to
More informationCALIBRATION FOR LAL20X & LAL24X
CALIBRATION AND FAULT FINDING FOR LAL20X & LAL24X DUMPY LEVELS MEASURING EXPERTS SINCE 1869 How The LAL20X & LAL24X Works The Automatic level is called Automatic because it requires only a simple basic
More informationWiring diagrams 14 1. Component key for wiring diagrams 1 to 29 Note: Not all the items listed will be fitted to all models
Wiring diagrams 14 1 Component key for wiring diagrams 1 to 29 Note: Not all the items listed will be fitted to all models No Description 00200 Alternator with built-in regulator 00500 Battery 01001 Starter
More informationINSTALLATION MANUAL. Installation Instructions
INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate
More informationLED Security Spotlight User Manual
MOT ION-TR ACKING LED Security Spotlight User Manual www.jascoproducts.com 1-800-654-8483 2 TABLE OF CONTENTS Parts List 3 Questions? Missing Parts? 4 Installation (Wall mount) 6-9 Installation (Eave mount)
More informationInstallation & Maintenance Instructions Joystick- single Joystick - double Touch panel Wireless remote control
Installation & Maintenance Instructions Joystick- single Joystick - double Touch panel Wireless remote control NS-EN ISO 9001:2000 Art.nr. 117-00155 FCC ID: R78-RC-01 R78-ECU-01 XF Rev: 1-2008 Side 1 Contents
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationV94 BULK TAPE DEGAUSSER
TECHNICAL MANUAL Operating and Maintenance Instructions for V94 BULK TAPE DEGAUSSER V94 BULK TAPE DEGAUSSER TECHNICAL MANUAL Document No. M000208 Production Standard ZZ 009 415 WARNING To help minimise
More informationLiteAide OWNER'S MANUAL PREASSEMBLED AUTOMATIC SECURITY FLOODLIGHTS MOTION SENSOR SECURITY LIGHTING SYSTEMS
OWNER'S MANUAL PREASSEMBLED AUTOMATIC SECURITY FLOODLIGHTS MOTION SENSOR SECURITY LIGHTING SYSTEMS LiteAide HE-100B HE-100BW HE-112 HE-112W HE-117 HE-117W HE-117-2B OWNER'S MANUAL FLOOD LAMPS (BULBS) Your
More informationVariShock Adjustment and Tuning Guide - QuickSet 2
VariShock Adjustment and Tuning Guide - QuickSet 2 This guide covers adjustment features and tuning procedures for VariShock QuickSet 2, double-adjustable, shock absorbers. The information contained has
More informationMoomba 2007/2008. Troubleshooting (Electronic Throttle Engines)
Moomba 2007/2008 Troubleshooting (Electronic Throttle Engines) System Not Controlling/Surging in both RPM & Speed Mode You can quickly perform a Control Test to confirm whether PerfectPass has proper control
More informationAdaptive Cruise Control System Overview
5th Meeting of the U.S. Software System Safety Working Group April 12th-14th 2005 @ Anaheim, California USA 1 Introduction Adaptive Cruise System Overview Adaptive Cruise () is an automotive feature that
More informationINSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS
3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More information5W LED Energy Saver PIR Bulkhead
5W LED Energy Saver PIR Bulkhead Model: LED88PIR Black I n s t a l l a t i o n & Ope r a t i n g I n s t r u c t i o n s 1. General information: The unit utilises passive infrared technology to detect
More information1000-LB. TRAILER JACK OWNER S MANUAL
1000-LB. TRAILER JACK OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More informationCMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM
INTRODUCTION CMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM Thank you for purchasing the CMD-8000 Commander from Dakota Digital. This, along with many other products that Dakota Digital has
More informationLED MOTION ACTIVATED FLOOD LIGHT
Utilitech & UT Design are registered trademarks of LF, LLC. All Rights Reserved. ITEM #0460794, 0459228 LED MOTION ACTIVATED FLOOD LIGHT MODEL #SE1019-WH3-02LF0-U, SE1019-TBZ-02LF0-U Français p. 8 Español
More informationCooling system components, removing and installing
Page 1 of 34 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
More informationHigh Power Receiver CR-W400U Operating Instructions
High Power Receiver CR-W400U Operating Instructions Please read these instructions carefully before using this product and save this manual for future use. Panasonic welcomes you to our ever growing family
More information12-Volt Negative Ground Installation Instructions
12-Volt Negative Ground Installation Instructions For Part Number: 1141, 1164, 1165, 1181 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for
More informationMobile Satellite Solutions. A WiWorld Partner SATELLITE TV ANTENNA CONTROLLER RFM-1000/1100 TECHNICAL MANUAL STOW SEARCH
Mobile Satellite Solutions A WiWorld Partner SATELLITE TV ANTENNA CONTROLLER RFM-1000/1100 TECHNICAL MANUAL SEARCH STOW Ver. 1 June 2012 WARNING Make all electrical and coax connections from the controller
More informationwith MERCURY FREE 1 HP Relays ! WARNING Before using this product read and understand instructions.
B Installation & Maintenance Instructions MM-414 Series 150E and 157E Low Water Cut-Off/Pump Controllers For Steam Boilers and Other Level Control Applications A Typical Applications: Primary or secondary
More information1. SAFETY RULES. 8. Avoid placing objects in the path of the blades.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationSHIFT INTERLOCK SYSTEM SHIFT INTERLOCK SYSTEM
SHIFT INTERLOCK SYSTEM The shift lock system is designed to ensure the proper operation of the automatic transmission. The driver must depress the brake pedal in order to move the gear selector from Park
More informationPRO PLM Installation Instructions
PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More information1R / 4-BUTTON SERIES
Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote
More informationElectronic Brake Controller Hayes Brake Controller Company ENERGIZE III P/N # 81741B or ENERGIZE XPC P/N #81745 OPERATION MANUAL
Electronic Brake Controller Hayes Brake Controller Company ENERGIZE III P/N # 81741B or ENERGIZE XPC P/N #81745 OPERATION MANUAL ENERGIZE III is for trailers with 2 or 4 electric brakes and vehicles with
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationWE-350 Series ¼ Turn Electric Actuator
WE-350 Series ¼ Turn Electric Actuator Operation and Installation Manual Pg 1 (Rev. 020113) Table of Contents 1.0 General 1.1 Pre-Installation Inspection 1.2 Storage 1.3 Features & General Information
More information2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationOwner s Guide and Installation Manual. Vancouver Model Name. 21321, 21328 Model No. English Español
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Vancouver Model Name 21321, 21328 Model No. Type A Models Owner s Guide and Installation
More informationTelefon (+45) 43 43 82 00 Telefax (+45) 43 43 74 75 mail@uni-valve.com www.uni-valve.com. Installation and operating manual
Uni-Valve A /S VENTILER & INSTRUMENTER Telefon (+45) 43 43 82 00 Telefax (+45) 43 43 74 75 mail@uni-valve.com www.uni-valve.com UNI-EL Electric actuator Installation and operating manual Remote position
More information1. SAFETY RULES WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT".
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationTreasure Cove Metal Detector
Treasure Cove Metal Detector Fortune Finder 1020 OWNER S MANUAL www.treasure-cove.com 805-658-2328 With your 1020 metal detector, you can hunt for coins, relics, jewelry, gold, and silver just about anywhere,
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL AND IGNITION 2012-2014 Yamaha T-Max 530 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol
More informationHCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply
1. INTRODUCTION HCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply User Manual This family of efficient, upgraded SMPS with small form factor, auto cross over CV CC,
More informationModel 37045-Series. PumpAgents.com - buy pumps and parts online QUIET - FLUSH ELECTRIC TOILET. Model 37045-Series FEATURES SPECIFICATIONS INSTALLATION
PumpAgents.com - Click here for Pricing/Ordering Model 37045-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual function
More informationPRESSURE GOVERNOR, ENGINE MONITORING, AND MASTER PRESSURE DISPLAY MODELS: TGA300, TGA400
Document Number: XE-TGA3PM-R0A TGA300 Rev130107 TGA300 PRESSURE GOVERNOR, ENGINE MONITORING, AND MASTER PRESSURE DISPLAY MODELS: TGA300, TGA400 TGA400 FIRE RESEARCH CORPORATION www.fireresearch.com 26
More informationWINDOW ROOM AIR CONDITIONER
WINDOW ROOM AIR CONDITIONER Installation and Operation Manual Electromechanical Remote Control CAPACITIES 220V - 60 HZ. 12,000; 18,000; 24000 BTU/HR 220V-240V - 50 HZ. 12,000; 18,000; 24000 BTU/HR Please
More informationRain+Birdt. Simple To Set Timer (SST) Setup & Operation Instructions. English. 1-800- RAIN BIRD (800-724-6247) or visit www.rainbird.
Rain+Birdt Simple To Set r (SST) Setup & Operation Instructions English Installation...2 Tools and Supplies Needed...2 Step 1. Mount r...2 Step 2. Connect Power...2 Indoor r...2 Outdoor r...2 Step 3. Connect
More informationVISM Evolution Scope Series
1 VISM Evolution Scope Series Congratulations on the purchase of your New VISM Evolution (EVO) Series Scope! The EVO Series of Scopes give you many great high end features and various magnification ranges
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationChevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G
INSTALLATION INSTRUCTIONS FOR PART 99-3307G Chevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationPart I - Installation
400 Series Pressure and Differential Pressure Switches Types: H400, H402, H403, H400K, H402K, J400, J402, J403, J400K, J402K UNITED ELECTRIC CONTROLS Installation and Maintenance Instructions Please read
More informationSERVICE MANUAL RESIDENTIAL ELECTRIC AND LIGHT DUTY COMMERCIAL ELECTRIC WATER HEATERS. Troubleshooting Guide and Instructions for Service
RESIDENTIAL ELECTRIC AND LIGHT DUTY COMMERCIAL ELECTRIC WATER HEATERS SERVICE MANUAL Troubleshooting Guide and Instructions for Service (To be performed ONLY by qualified service providers) Models Covered
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationEll STEERING COLUMN CONTROLS STEERING COLUMN CONTROLS
STEERING COLUMN CONTROLS Ignition Switch........ 2-1 LightinglTurn Signal Control Lever... 2-5 Windshield Wiper and Washer Lever... 2-6 Rear Window Wiper/Washer Switch (if equipped)... 2-8 Tilt Steering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE KEYLESS ENTRY MODELS KE100 / KE150 / 1702 CONTENTS System Features... 1 System Components... 1 Technical Assistance... 1 Before You Begin... 1 Precautions... 1-2 Making
More informationAEROMOTIVE Part # 16302 INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 16302 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationM A R C O. CP-670 AUTOMATIC CHART PROJECTOR Instruction Manual
M A R C O CP-670 AUTOMATIC CHART PROJECTOR Instruction Manual CONTENTS GENERAL DESCRIPTION............... 1 INSTALLATION...................... 2 Mounting the Projector Positioning the Projector Positioning
More informationModel 2300DR Installation Guide
Model 2300DR Installation Guide POWER ACCESS CORPORATION P.O. BOX 1050 170 MAIN STREET NEW HARTFORD, CT 06057 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS
More informationTroubleshooting Guide for Jacks Down LED Lights
Troubleshooting Guide for Jacks Down LED Lights Equalizer Systems Auto-Level systems manufactured after 2005 feature a pressure switch system that monitors the retracted state of leveling jacks and any
More informationBOSCH D-JETRONIC Volkswagen: Type 3 & 4
BOSCH D-JETRONIC Volkswagen: Type 3 & 4 MANIFOLD PRESSURE CONTROL SYSTEM (MPC) DESCRIPTION The Bosch D-Jetronic electronic fuel injection system is composed of 3 major subsystems: the air intake system,
More informationQuickie Rhapsody Service Manual
Quickie Rhapsody Service Manual 2006 Sunrise Medical Inc. 101976 Rev A Quickie Rhapsody Service Manual Contents Introduction... 0.1 VR2 Controller... 0.2 Plugs/Connectors... 0.3 Basic Tool List & Main
More informationFuel Injection Pump, Rotary (005-014)
Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train
More informationINSTRUCTION BOOK FOR. Large Cosmopolitan Electrol
INSTRUCTION BOOK FOR Large Cosmopolitan Electrol Important Safety Instructions When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and
More informationBathroom Cabinet. Installation & User Guide. Illuminated Mirrors. www.illuminated-mirrors.uk.com
Illuminated Mirrors The UK s Largest LED Mirror Supplier to Trade and Retail Installation & User Guide Bathroom Cabinet www.illuminated-mirrors.uk.com Bathroom Cabinet Installation & User Guide Thank you
More informationIstruzioni per regolatore elettronico dell iniezione
Istruzioni per regolatore elettronico dell iniezione Thank you for choosing the Free Spirits Fuel Injection Module. The module is only usable for the following models: Street Triple 2008-2011 Speed Triple
More informationUser s Manual for ELPLL02 Long-Focal Length Zoom Lens
User s Manual for ELPLL02 Long-Focal Length Zoom Lens This long-focal length zoom lens is designed for use only with EPSON multimedia projectors. It makes it possible to increase the distance between the
More information