Installation E Combination Drench Shower/Eyewash. Table of Contents

Size: px

Start display at page:

Download "Installation E19-310. Combination Drench Shower/Eyewash. Table of Contents"

Julius Daniel
7 years ago
Views:

1 Installation E Combination Drench Shower/Eyewash Table of Contents Pre-Installation Information Installation Instructions Assembly of Components Parts List E Rev. E; EN 06-53F 007 Bradley Corporation Page 1 of 5 6/5/07 P.O. Box 309, Menomonee Falls, WI USA PHONE BRADLEY FAX (6)

...................... Parts List.....................................5 15-163E Rev.

2 R Datum Signe P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) E Installation Installation P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Unterschrift THIS SIDE UP! Packing List WARNING Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI (0.1 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z For questions regarding the operation or installation of this product, visit or call BRADLEY. Product warranties may also be found under Product Information on our web site at 6/5/07 Bradley Corporation E Rev. E; EN 06-53F

Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Unterschrift THIS SIDE UP!

3 Installation E Installation Supplies Required: (3) M10 floor anchors and bolts Piping to 1-1/" BSP water supply inlet Adequate supply pipe supports Piping to 1-1/" BSP drain outlet for eyewash Minimum 10mm (") drain to accommodate 115 liters per minute discharge for shower waste OPTIONAL: sign-mounting hardware Step 1: Secure base to floor 1. Install three suitable anchors (by installer) for M10 bolts in the floor (see Figure 1).. Bolt the base to the floor anchors using M10 bolts (supplied by installer). Step : Assemble eyewash 1. Assemble the remaining unit components as shown in Figure on page. Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. Use the rubber grip pad provided or a strap wrench around pipes when tightening to prevent marring. Place the grip pad on the pipe, then put the wrench over the grip pad and turn the pipe with the wrench The bottom edge of the showerhead should be 160mm (7'-1") from floor. Step 3: Connect water supply 160mm (7'-1") to Floor 133mm (5-1/") IMPORTANT: Do not rely on Bradley s Combination Unit to support supply piping. 1. Connect water supply piping to 1-1/" BSP NOTE: inlet on unit (piping supplied by installer). Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means.. Connect drain piping to 1-1/" BSP drain outlet on unit (piping supplied by installer). Figure 1 3. Hang the safety sign from the unit with the curtain hooks provided (or mount it to the wall using sign-mounting hardware supplied by installer). Ø 5mm (10") Ø 5mm (10") 9mm (9") 67mm (10-1/") 65mm (5-3/8") 610 mm (") 7mm (9-3/") 15mm (6") Top View From Bowl 13mm (5-5/8") 101mm (1") 1676mm (66") to Floor Ø 9mm (9") Flange with (3) Ø 10mm (3/8") Holes on Ø 03mm (8") Bolt Circle All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 3mm (1/8") per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 3mm (1/8"). Bradley Corporation E Rev. E; EN 06-53F 6/5/07 3

Install three suitable anchors (by installer) for M10 bolts in the floor (see Figure 1).. Bolt the base to the floor anchors using M10 bolts (supplied by installer). Step : Assemble eyewash 1.

4 P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Datum Unterschrift Signe E Installation Assembly of Components NOTE: If tee (Item 5) is used as a supply inlet, use plug (Item 6) on tee (Item ). BSP end (noted with black line on threads) /" BSP Supply Inlet NOTE: Use teflon tape only Flow Control This End NOTE: Items come preassembled as Item 8. Items come preassembled as Item 1. Items come preassembled as Item /" BSP Drain Outlet 1 Figure 6/5/07 Bradley Corporation E Rev. E; EN 06-53F

5 Installation E Parts List Item Part No. Qty Description Item Part No. Qty Description Base B Pipe Tee 1-1/" NPT x 1-1/" BSP LC 1 Pipe 1-1/" NPT x 699mm LW Pipe 1-1/" NPT x 57mm B 1 Reducing Tee w/ BSP End Pipe Plug 1-1/" NPT LL 1 Pipe 1" NPT x 9mm 8 S Stay-Open Ball Valve 1" NPT DC 1 Lockwasher Handle 8.3 S " Ball Valve with Nut Jam Nut only Stop Bracket Washer, Friction Curtain Hook LK 1 Pipe 1" NPT x 305mm Street Elbow 1 NPT 1 S Plastic Showerhead Assy Showerhead Shell Diffuser Screw A 1 Pull Rod - Long 1 S Europe Eyewash Sub-Assy Inlet Drain Fitting Street Elbow Reducing Tee DA 1 Lockwasher Union 1/" Female NPT 1.7 S /" Ball Valve with Nut Jam Nut only QX 1 Pipe 1-1/" NPT x 180mm Pipe Elbow 1-1/" NPT LE 1 Pipe Nipple 1-1/" NPT x 76mm PIpe Tee 1-1/" NPT LQ 3 Pipe 1/" NPT x 76mm Handle 16 E Yoke Assy. - Europe 16.1 S Yoke & Sprayhead Assy Tethered Dust Cover Cap Plug Pipe Plug 17 S Cup/Strainer Prepack Spacer, Drain Center Seal Gasket 17.3 S Supply Pipe Assy Cup Strainer E 1 Safety Sign Emergency Tag Grip Pad (not shown) Eyewash Receptor 1.3 S Plg. Nipple 1-1/" NPT x 76mm Prepack S5-1 includes Items 1.5, 1.7, 1.71, 15 Prepack S5-13 includes Items 1.5, 1.71, 15 Bradley Corporation E Rev. E; EN 06-53F 6/5/07 5

1-1/" NPT 7 113-006LL 1 Pipe 1" NPT x 9mm 8 S30-059 1 Stay-Open Ball Valve 1" NPT 8.1 1-00DC 1 Lockwasher 8. 18-19 1 Handle 8.3 S7-78 1 1" Ball Valve with Nut 8.31 110-1 1 Jam Nut only 8.

Installation S19-220PT S19-220BPT. Wall-Mounted Eyewash with Plastic Bowl. Wall-Mounted Eyewash with Stainless Steel Bowl.

Installation S19-220PT S19-220BPT. Wall-Mounted Eyewash with Plastic Bowl. Wall-Mounted Eyewash with Stainless Steel Bowl. Wall-Mounted Eyewash with Plastic Bowl Wall-Mounted Eyewash with Stainless Steel Bowl Table of Contents Pre- Information................ Instructions.................... Components and Parts List.......