Know-how makes the difference. Soft Seated Butterfly Valves

Transcription

1 Know-how makes the difference Soft Seated Butterfly Valves

2 With Dansk Ventil Center as your business partner, you are always guaranteed a wide and well sorted product range and a unique technical know-how. Product development is a key factor for DVC, ensuring you the best products at any time. PN16 Rated CE Approved Long Service Reduced Torque Unique Seat Wave Line Unique Bushing System Perfect Turning & Centric Positioning Replaceable seats on hard back-up ring in both Wafer and LUG What is important to you, when you buy Soft Seated Butterfly Valves? What about: Long life span? Changable liner construction? PN16 rated? Unique seat wave line? Unique bushing system? Perfect turning & centric positioning? Soft Seated Butterfly Valves from Dansk Ventil Center are characterized by their long service and reduced torque. The Soft Seated Butterfly Valves are available in a wide range of dimensions. 2 Know-how makes the difference B-2232-UK REV. A

3 Index Product presentation... 2 Table of contents... 3 Construction... 4 Product range and benefits... 5 Construction DN40-DN Structure and material specification, wafer and lug... 8 Dimensions, wafer and lug Torque and flow capacities Bolt Circle Diameter lug type Approvals and valve sizing Temperature and resistance Installation guide Hand levers Gear boxes Actuators Know-how makes the difference 3 B-2232-UK REV. A

4 Construction Stainless steel disc ensures blow-out proof stem Square stem - angled at 45. Material is AISI 420 or AISI 431 to insure high torque transmission without damage. Smooth finish surface V-ring provides a weather seal O-ring as secondary sealing ensures that media does not escape to the atmosphere through the stem guide PTFE bearing ensures perfect turning and centric positioning of the stem. The sleeve bearing provides excellent support if actuators are used for automation purposes Unique seat wave line rubber seat reduces the torque of the valve and extends the life span of the sealing. DN40-DN300 High quality GGG40 steel body with standard ISO 5211 mounting flange. Body is coated according to ISO C3 industrial standard with 3 layer Epoxy/Epoxy/PUR 160µ Disc with two-piece shaft construction enhances the flow capacity of the valve. The shape of the disc provides lower torque and prolongs the life span of the valve Both Wafer and LUG has fully changeable liner construction. LUG model has a specialy designed grove to insure uni-directional end of line installation with full differential pressure PTFE/graphite bearing ensures perfect turning and centric positioning of the stem. The bearing is placed inside the disc Bottom stem in AISI 420 or AISI 431 with smooth surface finish O-ring anti-dust type Seat vulcanized to a phenol back-up ring which makes seat replacement very easy. The tolerances assure 100% tightness at full differential pressure. The valve is ideal for vacuum applications and mounting between flanges is easily done Bottom plug ensures blowout proof design and acts as a weather seal 4 Know-how makes the difference B-2232-UK REV. A

5 Product range and benefits Soft Seated Butterfly Valve Type 2232 Wafer Dimensions DN40 - DN300 DN350 - DN600 On request DN DN40 to DN300 Extended life span This butterfly valve has a unique wave line rubber seat and a special disc shape, enhancing the life span of the valve and sealing. Reduced torque Due to the unique wave line rubber-seat and disc shape, the butterfly valve has a low breakaway torque. One of a kind It is the only butterfly valve in the world constructed with a bushing inside the disc - resulting in lower torque, lower friction, 100% tight shut-off function and a very long service. Seat construction On the Wafer type the seat is vulcanized onto a phenol back-up ring. The seat is replaceable. Wafer-valve multi-standard alignment holes suitable for different flanges: DN40 - DN300 wafer type: EN1092 PN10, PN16 ANSI150 BS10 TABLE D, TABLE E, JIS 10K, 16K. DN350 - DN600 wafer type: EN1092 PN10, PN16 ANSI150 BS10 TABLE D. Soft Seated Butterfly Valve Type 2242 Lug Dimensions DN40 - DN300 DN350 - DN600 On request DN700 - DN1200 DN40 to DN600 Perfect turning and centric positioning The butterfly valve has a PTFE/graphite bushing, which ensures perfect turning and centric positioning of the stem. Trouble-free mounting Seat construction On the LUG type the seat is vulcanized onto a phenol back-up ring. The seat is replaceable. Due to the specially designed body, the valve can be used as end of line valve (uni-directional). LUG-valve alignment holes suitable for specific mounting flanges: DN40 - DN150 lug type: EN1092 PN10 or PN16 or ANSI150. DN200 - DN600 lug type: EN1092 PN10 or ANSI150. Mounting bolts LUG: PN = Metric Mounting bolts LUG: ANSI = UNC DVC are able to offer other solutions on request...please ask for an offer Know-how makes the difference 5 B-2232-UK REV. A

6 Construction DN40 - DN300 Wafer & Lug type Body GGG40 is standard - 3 layer coating EPOXY/EPOXY/PUR, 160 µ. Types: Wafer and LUG Wafer has multi-standard alignment holes suitable for mounting flanges: DN40 - DN300 wafer type: EN1092 PN10, PN16 - ANSI150 - BS10 TABLE D, TABLE E, JIS 10K, 16K. DN350 - DN600 wafer type: EN1092 PN10, PN16 - ANSI150 - BS10 TABLE D. LUG has fixed threaded holes suitable for specific flanges: DN40 - DN150 lug type: EN1092 PN10 or PN16 or ANSI150. DN200 - DN600 lug type: EN1092 PN10 or PN 16 or ANSI150. Mounting bolts lug: PN = Metric and ANSI = UNC ISO 5211 top flange according to valve torque. Relief track on the ISO top mounting flange. Seat A unique dynamic wave line rubber seat provides a highly efficient seal. Reduced torque making automation very price competitive. Extended sealing life span. On the Wafer and Lug type the seat is vulcanized to a phenolic back-up ring - a replaceable construction. Simple seat replacement. 100% tightness at full differential pressure (PN16 = 16 bar from DN40 - DN150, PN10 = 10 bar from DN200 - DN600). Ideal for full vacuum applications. Trouble-free mounting between flanges. Disc Disc with two-piece shaft construction which enhances the Kv-value of the valve and reduces turbulence. The shape and finishing of the edge of the disc, provides the lowest possible operating torque with bubble-tight shut off, even at maximum operating pressure, thus extending the life span of the valve. 6 Know-how makes the difference B-2232-UK REV. A

7 Construction DN40 - DN300 Wafer & Lug type Shaft / bearings Square stem. PTFE bearing ensures perfect turning and centric positioning of the stem. The sleeve bearing provides excellent support, where actuators are used for automation purposes. Unique bottom bearing The bottom PTFE/Graphite bearing is one of a kind - it is placed inside the disc, where it is actually needed. Usually there would be a bearing in the bottom of the body - which means a rotating shaft that transmits the forces put onto the disc down to the bearing. The result is a displacement of the forces and this is prevented by the unique bottom bearing - giving the valve a longer and trouble-free life span. Long shafts for transmitting force are more vulnerable to excessive torsion than short shafts. V-type ring and end cover The V-ring provides a secondary seal which prevents leakage to the stem. The V-ring also provides a weather seal. The end cover is sealed at the bottom with a threaded plug. The end cover has an anti-dust O-ring. Know-how makes the difference 7 B-2232-UK REV. A

8 Type 2232 Wafer / 2242 Lug - DN40 to DN300 Structure and material Wafer No. Description Material Standard Coating 1 Stem Stainless steel - AISI Preventing plate Stainless steel - AISI Screw Stainless steel - AISI O-ring Same as liner 5 Bushings PTFE Lug 6 Body Ductile Iron - ASTM A536 Gr (GGG40) Carbon steel - ASTM A216 WCB (GSC25N) Stainless steel - ASTM A351 CF8M 3 layer coating EPOXY/EPOXY/PUR 160µ RAL layer coating EPOXY/EPOXY/PUR 160µ RAL Seat NBR EPDM-HT FPM GNBR (PP6FMZ...for gas) Type 2235/2245 EPDM WHITE, FDA 8 Disc Stainless steel - ASTM A351 CF8M Low alloy stainless steel - ASTM A276 (SS201) Ductile iron - ASTM A536 Gr (GGG40) Ductile iron - ASTM A536 Gr (GGG40) Alu-bronze - ASTM B148 C95800 Duplex Hastelloy Rilsan ECTFE 9 Bushing Graphite / PTFE 10 Stem Stainless steel - AISI O-ring Same as seat 12 Plug Steel Galvanized Other materials available. 8 Know-how makes the difference B-2232-UK REV. A

9 Type 2232 Wafer / 2242 Lug - DN350 to DN600 Structure and material No. Description Material Standard Coating 1 Stem Stainless Steel - AISI 420 Stainless Steel - AISI 431 (ANSI 150 and PN16 >DN300) 2 Preventing Plate Stainless Steel - AISI Screw Stainless Steel - AISI O-ring Same as liner 5 Bushings PTFE Wafer Lug 6 Body Ductile iron - ASTM A536 Gr (GGG40) Carbon Steel - ASTM A216 WBC (GSC25N) Stainless Steel - ASTM A351 CF8M 3 layer coating EPOXY/EPOXY/PUR 160µ RAL layer coating EPOXY/EPOXY/PUR 160µ RAL Seat NBR EPDM-HT FPM GNBR (PP6FMZ...for gas) Type 2235/2245 EPDM WHITE, FDA 8 Disc Low alloy stainless steel - ASTM A276 (SS201) Ductile Iron - ASTM A536 Gr (GGG40) Ductile Iron - ASTM A536 Gr (GGG40) Stainless Steel - ASTM A351 CF8M Alu-bronze - ASTM B148 C95800 Duplex Hastelloy Rilsan ECTFE 9 Screw Stainless Steel - AISI Stem Stainless Steel - AISI 420 Stainless Steel - AISI 431 (ANSI150 and PN16 >DN350) 11 O-ring Same as seat 12 Nut Stainless Steel - AISI O-ring Same as Seat 14 Bolts Stainless Steel - AISI Washers Stainless Steel - AISI Cover Steel 3 layer coating EPOXY/EPOXY/PUR 160µ RAL 9006 Know-how makes the difference 9 B-2232-UK REV. A

10 Type 2232 Wafer - DN40 to DN300 Dimensions (mm) C nxøk E nxøj øh/øi F G A øz M B ød L Dim. A B C D E F G øh øi nxøj nxøk L M øz ISO Weight [kg] free stem DN x F DN x F DN x F DN x F DN x 7 4 x F05/F DN x F DN x F DN x F DN x F DN x 11 4 x F10/F Type 2232 Wafer - DN350 to DN600 Dimensions (mm) øh nxøk C E nxøj øi F G øz A M B ød L Dim. A B C D E F G øh øi nxøj nxøk L M øz ISO Weight [kg] free stem DN x 14 4 x F12/F DN x 14 4 x F12/F DN x 18 4 x F14/F DN x 18 4 x F14/F DN x 18 4 x F16/F Know-how makes the difference B-2232-UK REV. A

11 Type 2242 Lug - DN40 to DN300 Dimensions (mm) E nxøj/øk C F øh/øi G A øz M B ød1 ød2 L Dim. A B C D1 D2 E F G øh øi nxøj nxøk L M øz ISO Weight [kg] free stem DN x F DN x F DN x F DN x F DN x 7 4 x F05/F DN x F DN x F DN x F DN x F DN x 11 4 x F10/F Type 2242 Lug - DN350 to DN600 Dimensions (mm) E C øh øi nxøk nxøj F G øz A M B ød1 L ød2 Dim. A B C D1 D2 E F G øh øi nxøj nxøk L M øz ISO Weight [kg] free stem DN x 14 4 x F12/F DN x 14 4 x F12/F DN x 18 4 x F14/F DN x 18 4 x F14/F DN x 18 4 x F16/F Know-how makes the difference 11 B-2232-UK REV. A

12 Torques and flow capacities for Type 2232 / 2242 Dim. Valve Torque /Nm 10º 20º 30º 40º 50º 60º 70º 80º 90º DN40 12 <1 < DN50 12 <1 < DN DN80 PN DN DN Optional choise DN DN Opening angle DN DN DN DN400 PN PN DN DN DN Kv = The number of m³ per hour of 20º C water at 1 bar pressure drop. Cv = Kv. Cv = The number of US gallons per minute of 60º F water at 1 psi pressure drop. Service- and media factor - Actuator Sizing Service factor [SF] Multiply by Medium factor [MF] Multiply by Medium factor [MF] Multiply by For dry service (Dry gas ON/OFF operation 1.15 Lubricating liquid/gas 0.90 /air)...or Dirty air slurry, natural Modulating operation 1.25 Viscous Liquids, Molasses 1.30 gas, dirty slurry,...or Lime water, chlorin gas, *) 2 cycle/day NC 1.15 Degreasing liquid 1.25 oxygen, powder...or **) 1 cycle/week NC 1.50 Saturated steam 1.20 Hydrodynamic torque NA *Valve is completely closed and opens 2 times a day minimum. ** Valve is completely closed and opens only one time per week or longer. Having a long period without maneuvering the valve, will increase the breakaway torque. NB: Please maneuver the DVC butterfly valve at least one time per month to avoid deformation of the rubber seat. EXAMPLE OF ACTUATOR SIZING: Simple ON/OFF operation, Medium: Molasses, Valve: 2231 DN [SF] x 1.30[MF] x 34[Nm] = 50.8Nm (Sizing torque actuator) Only choose one Service Factor [SF] and one Medium factor [MF] when calculating the sizing torque. TYPE 2242 LUG - Bolt Circle Diameter DN40 to DN600 Dim. PN 10 PN 16 ANSI 150 BCD [mm] No. bolts Nom. size BCD [mm] No. bolts Nom. size BCD [mm] No. bolts Nom. size DN M16 x M16 x 40 98,0 4 1/2 x 35 DN M16 x M16 x /8 x 35 DN M16 x M16 x /8 x 40 DN M16 x M16 x /8 x 40 DN M16 x M16 x /8 x 45 DN M16 x M16 x /4 x 45 DN M20 x M20 x /4 x 45 DN M20 x M20 x /4 x 50 DN M20 x M24 x /8 x 60 DN M20 x M24 x /8 x 65 DN M20 x M24 x x 70 DN M24 x M27 x x 85 DN M24 x M27 x /8 x 90 DN M24 x M30 x /8 x 100 DN M27 x M33 x /4 x 110 According to the DIN standard the thread type is metric. According to the ANSI standard the thread type is UNC. 12 Know-how makes the difference B-2232-UK REV. A

13 Valve Sizing Determining the size of butterfly valves for control purposes should not be done on the basis of the nominal diameter of the pipe but should be calculated on the basis of the operating characteristics in order to attain the correct control characteristics. Butterfly valves Type 2232 / Type 2242 from Dansk Ventil Center are designed with approximately equal percentage characteristics over an opening angle of 65. You only need to consider the opening angle when determining the size of control valves. When determining the valve nominal diameter calculate the Kv value from the below formula: Liquid: K V = Q x Gas: K V = V N 514 w Δp G x T Δp x p d K V Q w Δp V N G T P d = = = = = = = = Flow coefficient. Max. flow volume in m 3 /h. Exact weight in kg/dm 3. Pressure drop in bar. Max. flow in Nm 3 /h. Exact weight in kg/nm 3. Absolute temp. in Kelvin. Absolute pressure downstream in bar /2242 EXAMPLE DN Approvals LINER INFO CE - according to PED 97/23/EC 3.1 certificate according to EN NBR / EPDM certification ATEX certification Rubber liners (NBR, EPDM-HT and FPM): Rubber will over time loose flexibility and compression set. The higher the temperature rubber is installed in, the shorter the expected lifespan is. Our values for temperature is given to the best of our knowledge, and we advice that valves are tested for lifespan if installation is running near the given temperature limit. If in doubt, please consult us. Chart for temperature and resistance Liner Temperature Suitable for Unsuitable for EPDM-HT - 15 ºC ºC NBR NATURAL RUBBER* - 10 ºC + 80 ºC - 30 ºC + 80 ºC HYPALON * - 20 ºC + 75 ºC FPM - 20 ºC ºC Water, steam, alcohol, glycol, caustic soda, ozone, food products, glycerine, milk, oxygen, air, saturated salt, iron chloride, gelatine, dry hydrogen sulphide, potassium chloride, sodium, magnesium chloride Mineral oil, grease, air, seawater, gas, boric acid, aluminium chloride, ammonia gas, citric acid, diesel oil, fish oil, petrol, gelatine, glycerine, magnesium chloride, lactic acid, linseed oil, natural gas Abrasive medium, aluminium chloride, sugar beet fluid, boric acid, potassium chloride, citric acid, magnesium chloride, ferritic nitrate, formic acid, gelatine, sugar, glycerine, lactic acid, nitrogen Mineral, organic and inorganic chemicals, air, oxygen, fish oil, glycerine, citric acid, ozone, sodium solphate Oil, mineral acid, grease, phosphorus, tannic acid, gelatine, glycol, oxygen, slaked lime, carbon acid, natural gas, pulp, salt, sugar, sulphur Mineral oil, chlorine compounds, ketones, acetyl, chloride, asphalt, bromine, butane, butyl, petrol, diesel oil, acid, fish oil, freon, chlorine, natural gas, exhaust gas, nitric acid Ozone, acetone, aniline, chlorine dioxide, chromic acid, phenol, ethyl acetate, freon , hot nitric acid, styrene, hydrogen sulphide, isopropyl acetate, oxygen, sulphuric acid Steam, aniline, asphalt, butadiene, diesel oil, ethane, ethyl acetate, hydraulic oil, hydrochloric acid, linseed oil, methane, mineral oil, oxygen, styrene, soyabean oil, turpentine Ammonia, diesel oil, grease, ketone, methyl, phenol, propyl, bromine, nitric acid, tar, urea, varnish, lectine Hot water, steam, ketone, ammonia gas, acetone, formaldehyde, cellulose acetate, freon, urea, ethanoic acid, methyl Note: materials marked with * available on special request only. Know-how makes the difference 13 B-2232-UK REV. A

14 Installation guide Installation guide for Butterfly Valves Check that the specifications on the identification plate meet the requirements regarding pressure, temperature and media. The piping must have a straight line and the flanges have to be parallel. Furthermore there must be a distance between the flanges, corresponding to the face-to-face dimensions of the butterfly valve. The butterfly valve can be mounted in any direction. However if there are a lot of dirt particles on the bottom of the pipe, it will be suitable to mount the stem of the butterfly valve horizontally. This will protect the pivot point of the disc. Before commissioning, the pipe work has to be rinsed out to remove dirt and remnants of welding material, to avoid damage on the liner. During the rinsing procedure, the butterfly valve has to be positioned as open and may not be operated, before the rinsing has been completed. Welding operations may not be performed nearby the butterfly valve, as welding drops can damage the liner. Do not use gaskets. The liner works as sealing to the atmosphere. Where vacuum, high flow rate or water hammering can occur, flanges without a loose collar should be used, to obtain the best conditions. Carefully place the butterfly valve between the flanges, with the disc in closed position. Check that the flange covers the area of the liner. Afterwards tighten the bolts on the flange by hand. Carefully open and close the valve to check that the disc centralizes and the disc does not touch the flange. With the disc in the open position, tighten crosswise with a wrench. Though the valves are constructed to work as shown on the right, counter clockwise rotation - CCW - they can be reversed without problems. Please consider that the torque in this case will increase. As the butterfly valves are equipped with the unique wave shaped liner, the operation of the valves, either free stem, handle or gear operated, has to follow the guidelines as shown below. A small triangular shaped figure is placed on the liner - this triangle indicates which way the disc has to enter the liner. Generally spoken the disc has to close clockwise - CW - in order to have the lowest possible torque - and thus the longest possible life time. Turn disc CW towards arrow to close Turn 90 CW to close 2242 LUG, used as an end of line valve: Please notice that the valve is uni-directional. 14 Know-how makes the difference B-2232-UK REV. A

15 Construction - Hand lever Hand lever For DN40 to DN200 Alu. Aluminium hand lever Convenient installation and usage. Excellent surface design and comfortable operating. Position can be locked by fixing one bolt and nut in the lever hole. Standard anodized surface with powder epoxy coating. Stainless steel hand lever on request Dimensions (mm) and materials For DN40 to DN200 Aluminium C B F 1 ExE D Type Alu Valve dim. Size B C D ExE F Bolts Weight (Kg) No. Part Name Aluminium Surface standard option DN40 DN50 DN65 DN80 DN100 DN125 F x M6 x F x M8 x Column Diecast aluminum Powder epoxy odized 40µ 2 Holding Handle Diecast aluminum Powder epoxy odized 40µ 3 Locking Handle Diecast aluminum Powder epoxy odized 40µ 4 Spring Carbon Steel Q235 Steel Q235 SS DN150 F x M8 x DN200 F x M10 x Bolt / nut SS304 SS304 SS316 DVC are able to offer other solutions on request...please ask for an offer Mounting bracket for inductive switch ø12mm or ø18mm Signal for OPEN or Closed Mounting bracket for mechanical switch Signal for OPEN or CLOSED Know-how makes the difference 15 B-2232-UK REV. A

16 Construction - Gear Operators - DN 40 to DN 300 Gearboxes Type 5595 (DN50 - DN300) Aluminium alloy housing Steel input shaft Steel worm gear Ductile iron output gear segment Dustproof enclosure Units provided with hand wheel Adjustable travel stops are standard and factory set AISI 304 standard bolts and nuts Dimensions are valid for Type 2232 and 2242 Dimensions (mm) Type Valve dim DN x 11 S x S D2 n-d1 Ratio Output torque (Nm) Input torque (Nm) A B øb C D E øf H H1 Weight (Kg) DN x / 4 - M6x20 40: DN x DN x DN x DN x M6x20 40: DN x DN x DN x M10x30 45: DN x Know-how makes the difference B-2232-UK REV. A

17 Construction - Gear Boxes - DN 350 to DN 600 Gearboxes Type 5595 (DN350 - DN600) Ductile iron housing Steel input shaft Steel worm gear Ductile iron output gear segment Dustproof enclosure Units provided with hand wheel Adjustable travel stops are standard and factory set AISI 304 standard bolts and nuts Dimensions are valid for type 2232 and 2242 General Parameters n-m General Information Type Valve dim. Ratio Output torque (Nm) Input torque (Nm) Hand wheel ø (mm) Turns from open to closed Stem hole size Bolt size n-m DN : x M16 x DN : x M16 x DN : x M16 x DN : x M20 x DN : x M16 x Weight (Kg) Dimensions Type Mounting flange D1 d1 ø ø1 B C D H H1 H2 h E F M N F F F16 / F F25 / F Know-how makes the difference 17 B-2232-UK REV. A

18 Construction - Actuators Actuators Spring Return Double Acting Body is hard anodized (40µ) as standard but can be supplied PTFE coated or all stainless. Twin rack pistons made from die-cast aluminium - hard anodized or from galvanized cast steel. End caps are made from die-cast aluminium powder polyester painted, PTFE or nickel plated. The pinion is high-precision and integrative, made from nickel-alloy steel. Pre-loaded, coated high performance springs are made from corrosion resistance material (only Type Spring Return Actuators). Two independent external travel stop adjustment bolts can easily and precisely be adjusted +/- 5% at both open and close directions. Bearings and guides made from low friction, long life compound material to avoid direct contact between metals. NBR O-rings provide trouble-free operation at standard temperature ranges. For low and high temperatures FPM and Silicone are used. Actuator Principle and Torque Double Acting Actuator Spring Return Actuator CCW CW CCW CW A A A A B B B B A B A B A B A B CCW: Air to Port A forces the pistons outwards, causing the pinion to turn counter clockwise while the air is being exhausted from Port B. CCW: Air to Port A forces the pistons outwards, causing the springs to compress. The pinion turns counter clockwise while the air is being exhausted from Port B. Air to Port B forces the pistons inwards, causing the pinion to turn clockwise while the air is being exhausted from Port A. Loss of air pressure on Port A, the stored energy in the springs forces the pistons inwards. The pinion turns clockwise while air is being exhausted from Port A. CCW is standard at Dansk Ventil Center CCW is standard at Dansk Ventil Center CW: Air to Port A forces the pistons outwards, causing the pinion to turn clockwise while the air is being exhausted from Port B. CW: Air to Port A forces the pistons outwards, causing the springs to compress. The pinion turns clockwise while the air is being exhausted from Port B. Air to Port B forces the pistons inwards causing the pinion to turn counter clockwise while the air is being exhausted from Port A. Loss of air pressure on Port A, the stored energy in the springs forces the pistons inwards. The pinion turns counter clockwise while air is being exhausted from Port A. 18 Know-how makes the difference B-2232-UK REV. A

19 DVC Actuators - Standard conditions - 6 bar air supply Double Acting Actuators for Butterfly Valves Actuator size Output torque [Nm] Air supply ISO 5211 / mm Product no Bar F04 / Bar F03-F05 / Bar F05-F07 / Bar F05-F07 / Spring Return Actuators for Butterfly Valves BV Dimensions 2231/2241 DN 40 PN16 DN 50 PN16 DN 65 PN16 DN 80 PN16 DN 100 PN16 ISO 5211 / mm F05 / 11 F05 / 11 F05-F07/ Bar F05-F07 / DN 125 PN16 F07 / Bar F05-F07 / DN 150 PN16 F07 / Bar F07-F10 / DN 200 PN10 F10 / Bar F07-F10 / DN 250 PN10 F10 / Bar F10-F12 / DN 300 PN10 F10-F12 / Bar F10-F12 / DN 350 PN10 F12-F14 / Bar F14 / DN 400 PN10 F12-F14 / Bar F14 / DN 450 PN10 F14-F16 / Bar F16 / F14-F16 / Bar F16 / DN 500 PN10 DN 600 PN10 F16-F25 / 46 Actuator size Torque air [6bar] Torque spring Maximum number of springs ISO 5211 / mm Product no. BV Dimensions 2231/2241 ISO 5211 / mm F03-F05 / F03-F05 / DN 40 PN16 DN 50 PN16 F05 / F03-F05 / DN 65 PN16 F05 / F05-F07 / DN 80 PN16 DN 100 PN16 F05-F07/ F05-F07 / F07-F10 / DN 125 PN16 F07 / F07-F10 / DN 150 PN16 F07 / F10-F12 / DN 200 PN10 F10 / F10-F12 / DN 250 PN10 F10 / F12 / DN 300 PN10 F10-F12 / F14 / DN 350 PN10 F12-F14 / F14 / DN 400 PN10 DN 450 PN10 F12-F14 / 27 F14-F16 / F14 / Standard conditions: Water, 1kg/dm 3, 20 o C. Know-how makes the difference 19 B-2232-UK REV. A

20 Know-how makes the difference Dansk Ventil Center A/S Product Range Ball Valves Butterfly Valves Soft Seated Butterfly Valves Metal Seated Y-angle Globe Control Valves Thin Wafer Check Valves Safety Valves Knife Gate Valves Pneumatic Actuators Electrical Actuators Brackets for Actuators Limit Switches Level Gauges - Reflex & Transparent Control valves Pressure Reducing valves Dansk Ventil Center is committed to meeting the needs of customers in an environmentally sound and sustainable manner, through continuous improvements in environmental performance in all our activities. Dansk Ventil Center is located in the northern part of Europe, in the heart of Denmark. Visit us at and learn more about Dansk Ventil Center and our products....for very harsh environments DVC offers completely Stainless Steel assemblies. Valves Solenoid valve Electro Pneumatic positioner Pneumatic actuator Mechanical switch box Filter regulator Dansk Ventil Center A/S Ferrarivej 14 DK-7100 Vejle Denmark Tel.: Fax: mail@dvcas.dk Web: