A completed Ser 1 E-Type body shell built to system 3 specifications ready for the paint process

Transcription

1

2 on several major assembly jigs which locate key mounting points throughout the build process professional Spot Welders are used to give an original appearance and adhere to the original design. Ser.1-2 and 3 Models are available in both Drop Head and Fixed head versions. the completed Bodies are Lead Loaded Cleaned off, the door seals are fitted to give a better than original fit to Door, Bonnet gaps etc. External Chrome work is trial fitted prior to leaving the works where the Body Shells can be ready for the Paint Process. A completed Ser 1 E-Type body shell built to system 3 specifications ready for the paint process Martin Robey Engineering Limited have been producing completely new Body Shells for E Type Jaguars since 1982, after restoring several Body Shells it was apparent that they all suffered similar corrosion problems and when corrosion damaged panels were removed it only revealed further corrosion and undesirable repairs, there never seemed much of the original body left before the rebuild could take effect, therefore it was decided to produce the few remaining panels that were not in production at the time and start producing all New Body Shells. To accommodate customers with some of their own parts such as Doors, Boot Lids and Bonnets the System One, Two and Three processes came about. that are Pressed Out, Laser Profiled and assembled using Motor Industry Methods and equipment, quality appearance and dimensional accuracy to the original specification is an important feature of the Martin Robey Panels and Body Shells. The build process involves using sub units such as Bulkheads, Floors, Rear End Assemblies etc., which are all assembled Martin Robey Engineering Ltd. recently installed its very first Robot. The Robot is the latest of many of the company s machines that are fully computerised. Floor Units & Sub-Assemblies are also available for the experienced who wish to rebuild their Body Shell or complete a Sub Assembly using Our Panel Kits. The Body Shells use high quality Martin Robey Body Panels E-type Floor Units are assembled in a series of comprehensive assembly jigs

3 Full Body Shells System Re-Builds Full Body Shells are available in several variation we call them System Rebuilds. System I is a complete Body Shell, all new with a Bulkhead fitted and all welded with your Doors and Bootlid Fitted, Lead Loaded and cleaned back, all fully jig Built. Series DHC models 26,794.43* Series DHC models 26,834.50* Series DHC models 26,840.24* System II is a System I with a Doors and Boot Lid Supplied and Fitted Series DHC models 28,703.04* Series DHC models 28,743.26* Series DHC models 28,229.77* System III is a System II with a Bonnet supplied and fitted with front-rear lights, Bumpers, Door chromes and trial fitting. Series DHC models 36,398.36* Series DHC models 36,438.54* Series DHC models 36,418.58* Fixed Head Models Prices shown are for Ser.1-2 Drop Head Coupe Models. For Fixed Head Coupes please add 9,500 based upon customer supplying roof assembly and rear hatch unit in suitable condition. All Prices are EX-Works and subject to VAT if applicable *Aug Jul 2016 System Re-Builds are available normally in approximately weeks from order and deposit. The prices given do not include any Fixtures, Fittings, Hinges, Locks, Engine Frames etc, or Packing or Shipping. Additional Equipment: Inner Sill Reinforcing , Inner Seat Belt Kit , Early 3.8 Features Can Be Incorporated Into Systems and Sub Assembly units. A Ser DHC restored at the works using a complete Martin Robey Body Shell to System 3 Specifications.

4 Ser Early Features Very Early E Types have early features that were discontinued as part of upgrades for these early cars. Careful research and study of the Motor car is essential to evaluate which of these features are relevant to particular vehicles and there probably was not two vehicles exactly the same in the first few days-weeks of production. It must be remembered that some vehicles will have undergone factory upgrades or as part of general servicing or restoration during the life of the vehicle. It must be also remembered that many more vehicles were exported to the USA that upgrades may have been incorporated to Federal Specification Cars that UK Cars built in the same period so dates of manufacture is not the only consideration to be made, Chassis or VIN Number is the most important Allie in identifying early features, there are several books available that list most, but not every feature by relevance to chassis Number. We offer most of the important Early Features for the Ser models, we offer them as a Fixed Price Supplement and can usually accommodate other less well known features that may have been fitted to a very smaller number of vehicles or perhaps just the one. Early Features 3.8 Ser.1 Bonnet (Front End) Bulkhead Unit Inner Sill Floor Panels Door Assembly Boot Floor & Rear End Assembly Number Plate Panel Fuel Filler Box Separate Louvre Panels Spot Weld Air Valence Panels Seam Welded Centre Panel Nose Section Side Locking Mechanism Bolt On Mirror Rod Bracket Fixings Pop Riveted Brake-Clutch Reservoir Bracket Side Locking A Post Without Pressing For Lock Rod Transmission Tunnel Side Panel RH Plain Pressing Weld Nuts For Side Locking Bonnet Catches Flat Floors Without Footwell Including Separate (2 Part) Radius Cup Mounting Plate Rear Bulkhead Panel Straight One Piece Without Separate Weld For Extra Seat Movement Early Style Door Inner Panel, FHC & DHC Early Style Drip Tray, FHC & DHC Door Skin 2 Part With Spot Welded Top Section For Slim Early Top Door Chromes Finisher (DHC Only) Pop Riveted Reversing Light Pod With Boot Floor Rails One Piece Spot Welded Pop Riveted Reversing Light Pod With Boot Floor Stiffeners 3 Part Style With Centre One Pop Riveted In Position Pop Riveted Reversing Light Pod With All Rails 3 Part Style All Pop Riveted In Position Water Drain Tubes 1 Central One Fitted On LH Side Of Reversing Light Pod 1 Central Plus 1 Further On RH Rear Quarter Panel Small Aperture For Rear Light Access Fuel Filler Box without Reinforcing Indentation top Half Of filler Box And Without Drawn Tube To Fuel Box Please Note: There are other early features to the Body Shell Units Please do not hesitate to talk to us about your Motor Car; we can usually accomodate these even if not listed

5 Sub Assembly Units Roadster Series 1-2 A Sub Assembly Unit is a Body Shell with a New Bulkhead supplied and fitted but without the outer body panels supplied and fitted. Ser Sub Assembly Unit with Bulkhead 14,192.25* Ser Sub Assembly Unit with Bulkhead 14,232.25* Ser Sub Assembly Unit with Bulkhead 14,291.59* The Sub Assembly is designed for the experienced amateur Body Builder or the Professional Body Shop. These Units are mostly welded together and can be completed without the use of a Full Assembly Jig. Sub Assembly without Bulkhead and without the Outer Body Panels Fitted. Ser DHC Sub Assembly Unit without Bulkhead 9,488.98* Ser DHC Sub Assembly Unit without Bulkhead 9,529.04* Ser DHC Sub Assembly Unit without Bulkhead 9,584.32* Delivery is usually approximately 6-10 weeks from Order. The cost of a new bulkhead not fitted is 4,703.27* The outer Body Panels that are not fitted are available in Kits. Being: Ser 1 DHC 3.8 & 4.2 Alpha Base Kit (See list of Parts) 2,187.57* Ser 1 DHC 3.8 & 4.2 Beta Alpha Kit plus Door and Bootlid 4,090.08* Ser 1 DHC 3.8 & 4.2 Delta which is a Beta plus a Bonnet 9,514.40* All prices are ex works and subject to Value Added Tax for European Sales. ADDITIONAL EQUIPMENT Inner Sill Reinforcing Inner Seat Belt Kit Early 3.8 Features Can Be Incorporated Into Sub Assembly Also * Aug July 2016

6 Sub Assembly Units For Fixed Head Coupé We can build Sub assembly units for FHC, Series 1 and Series 2-3 E-type models, we can vary the content of the unit to suit to vehicle requirements. Therefore any prices shown are to guide only. They are designed for fitting the roof assembly and outer panels by a professional restorer or experienced enthusiast. They can be supplied with a either a new bulkhead supplied and fitted, using a reconditioned bulkhead or using a suitable bulkhead supplied by a customer. Guide price with new bulkhead supplied and fitted 13, VAT *Aug July 2016

7 Floor Units Available for series 1&2 Drop Head and Fixed Head models 3.8 Footwell floor assembly 1,313.57* (Ex.VAT) Full floor unit For Series flat floor model Call for more information! +44 (024) All Prices are subject to VAT if applicable 3,025.12* (Ex.VAT) *Aug July 2016

8 SUB ASSEMBLY UNIT FOR SER ROADSTER WITH REAR END ASSEMBLY 1 X BULKHEAD BULKHEAD UNIT INCLUDING TOP SKUTTLE PANEL 4, , X BD16008F/R FUEL TANK MTG BRACKET X BD16212 REINFORCING TONNEAU X BD18949/50 BOOT HINGE MTG BRACKET X BD18963 INTERIOR LIGHT SHIELD X BD27181 FUEL PUMP MTG BRACKET X MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS X MRE112ALH/BRH TRANSMISSION TUNNEL SIDE PANELS X MRE115 TUNNEL STIFFENER X MRE117LH/RH STIFFENERS X MRE118LH/RH CLOSING PANEL X MRE119 CENTRAL TUNNEL FACING X MRE120LH/RH TUNNEL FWD SIDE X MRE121LH/RH INNER PEDAL SIDE X MRE122RH OUTER PEDAL X MRE122ELH OUTER PEDAL SIDE X MRE14LH/RH FULL FLOOR X MRE15LH/RH INNER SILLS X MRE19 FRONT STIFFENERS X MRE20RH/LH REAR STIFFENERS X MRE24A CROSSMEMBER TO FULL FLOOR X MRE29RH/RH INN ARCH LH X MRE2LH/RH BHD TO SILL X MRE30RH/LH DOOR SHUT FACE PANEL ASSY X MRE3ARH RH 3.8 BULKHEAD PANEL X MRE4ALH LH 3.8 BULKHEAD PANEL X MRE42A CLOSING PANEL X MRE58 UPPER FLOOR X MRE59LH/RH FLOOR STIFFENER BRACKETS X MRE60 TUNNEL ASSEMBLY X MRE61 TOP PANEL REAR FLOOR X MRE62 PANEL FRONT TO BOOT FLOOR X MRE63 PANEL ASSEMBLY X MRE64 REAR BULKHEAD X MRE65 REINF CHANNEL X MRE68BRH RH 38 ARCH VALANCE X MRE68LH INN VALANCE LH X MRE69LH/RH ARCH FWD X MRE71LH/RH TOP PANEL INNER X MRE72LH/RH REAR CHASSIS LEGS X MRE73A RADIUS ARM CUPS (RIVETED) X MRE76LH/RH INNER PANEL DOOR SHUT FACE X MRE96A REAR END ASSEMBLY D.H.C Bulkhead 4, Parts Total Excl Bulkhead 5, Labour For Assembly 3, Total Sub Assembly Cost 14, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 9, SUB ASSEMBLY WITH BULKHEAD 14, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

9 SUB ASSEMBLY UNIT FOR SER ROADSTER WITH REAR END ASSEMBLY 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL 4, , x BD16008F/R FUEL TANK MTG BRACKET x BD27181 FUEL PUMP MTG BRACKET x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS x MRE112C TRANSMISSION TUNNEL SIDE PANELS SER x MRE112D TRANSMISSION TUNNEL SIDE PANELS SER x MRE115 TUNNEL STIFFENER x MRE117LH/RH STIFFENERS x MRE118LH/RH CLOSING PANEL x MRE119A CENTRAL TUNNEL FACING SER x MRE120RH TUNNEL FORWARD SIDE x MRE120LH TUNNEL FWD SIDE x MRE121LH/RH INNER PEDAL SIDE x MRE122LH/RH OUTER PEDAL x MRE14LH/RH FULL FLOOR x MRE15LH/RH INNER SILLS x MRE19 FRONT STIFFENERS x MRE20LH/RH REAR STIFFENERS x MRE25A CROSSMEMBER SLANT FULL x MRE29LH/RH INN ARCH LH x MRE2LH/RH BHD TO SILL x MRE30LH/RH DOOR SHUT PANEL SER x MRE3RH BULKHEAD PANEL x MRE42 CLOSING PANEL SER.1 DHC x MRE4LH BULKHEAD PANEL 4.2 EARLY x MRE58 UPPER FLOOR x MRE59LH/RH FLOOR STIFFENER BRACKETS x MRE60 TUNNEL ASSEMBLY x MRE61 TOP PANNEL REAR FLOOR x MRE62A PANEL TO BOOT FLOOR x MRE63 PANEL ASSEMBLY x MRE64 REAR BULKHEAD x MRE65 REINFORCED CHANNEL x MRE66 REINFORCING CHANNEL TONNEAU x MRE68LH/RH INN VALANCE x MRE69LH/RH ARCH FWD x MRE71LH/RH TOP PANEL INNER x MRE72LH/RH REAR CHASSIS LEGS x MRE73A RADIUS ARM CUPS (RIVETED) x MRE76LH/RH INNER PANEL DOOR SHUT FACE x MRE9ALH/ARH BULKHEAD D PANEL x MRE96A REAR END ASSY D.H.C Bulkhead 4, Parts Total Excl Bulhead 5, Labour For Assembly 3, Total Sub Assembly Cost 14, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 9, SUB ASSEMBLY WITH BULKHEAD 14, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

10 SUB ASSEMBLY UNIT FOR SER ROADSTER WITH REAR END ASSEMBLY 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL 4, , x BD16008F/R FUEL TANK MTG BRACKET x BD27181 FUEL PUMP MTG BRACKET x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS x MRE112C TRANSMISSION TUNNEL SIDE PANELS SER x MRE112E TRANSMISSION TUNNEL SIDE PANELS SER x MRE115 TUNNEL STIFFENER x MRE117LH/RH STIFFENERS x MRE118LH/RH CLOSING PANEL x MRE119A CENTRAL TUNNEL FACING SER x MRE120RH TUNNEL FORWARD SIDE x MRE120LH TUNNEL FWD SIDE x MRE121LH/RH INNER PEDAL SIDE x MRE122LH/RH OUTER PEDAL x MRE14LH/RH FULL FLOOR x MRE15LH/RH INNER SILLS x MRE19 FRONT STIFFENERS x MRE20LH/RH REAR STIFFENERS x MRE25A CROSSMEMBER SLANT FULL x MRE29LH/RH INN ARCH LH x MRE2LH/RH BHD TO SILL x MRE32LH/RH DOOR SHUT PANEL SER x MRE3RH BULKHEAD PANEL x MRE42 CLOSING PANEL SER.1 DHC x MRE4LH BULKHEAD PANEL 4.2 EARLY x MRE58 UPPER FLOOR x MRE59LH/RH FLOOR STIFFENER BRACKETS x MRE60 TUNNEL ASSEMBLY x MRE61 TOP PANNEL REAR FLOOR x MRE62A PANEL TO BOOT FLOOR x MRE63 PANEL ASSEMBLY x MRE64 REAR BULKHEAD x MRE65 REINFORCED CHANNEL x MRE66 REINFORCING CHANNEL TONNEAU x MRE68LH/RH INN VALANCE x MRE69LH/RH ARCH FWD x MRE71LH/RH TOP PANEL INNER x MRE72LH/RH REAR CHASSIS LEGS x MRE73A RADIUS ARM CUPS (RIVETED) x MRE76LH/RH INNER PANEL DOOR SHUT FACE x MRE9ALH/ARH BULKHEAD D PANEL x MRE96C REAR END ASSY D.H.C Bulkhead 4, Parts Total Excl Bulhead 5, Labour For Assembly 3, Total Sub Assembly Cost 14, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 9, SUB ASSEMBLY WITH BULKHEAD 14, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

11 SUB ASSEMBLY UNIT FOR JAGUAR E TYPE SER FIXED HEAD COUPE 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL 4, , x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS x MRE112ALH/BRH TRANSMISSION TUNNEL SIDE PANELS x MRE115 TUNNEL STIFFENER x MRE117LH/RH STIFFENERS x MRE118ALH CLOSING PANEL LH x MRE118ARH CLOSING PANEL x MRE14LH/RH FULL FLOOR x MRE15LH/RH INNER SILLS x MRE19 FRONT STIFFENERS x MRE20LH/RH REAR STIFFENERS x MRE24A CROSSMEMBER TO FULL FLOOR x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD x MRE29BLH/RH INN ARCH LH x MRE2LH/RH BHD TO SILL x MRE30LH/RH DOOR SHUT PANEL FHC x MRE3RH BULKHEAD PANEL x MRE42 CLOSING PANEL SER x MRE4LH BULKHEAD PANEL x MRE58 UPPER FLOOR x MRE59LH/RH FLOOR STIFFENER BRACKETS x MRE60 TUNNEL ASSEMBLY x MRE61 TOP PANNEL REAR FLOOR x MRE62 PANEL TO BOOT FLOOR x MRE63 PANEL ASSEMBLY x MRE72LH/RH REAR CHASSIS LEGS x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) x MRE76ALH/RH INN SHUT RH/LH x MRE78LH/RH INN VALANCE LH x MRE96B REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR NUMBER PLATE PANEL ETC SER.1 FHC 2 x MRE9ARH/ALH FRONT INNER BULKHEAD PABEL x MRE9BLH/BRH INNER BULKHEAD PANEL SIDE x MRE43 REAR CLOSING PANEL Bulkhead 4, Parts Total Excl Bulhead 5, Labour For Assembly 3, Total Sub Assembly Cost 13, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 8, SUB ASSEMBLY WITH BULKHEAD 13, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

12 SUB ASSEMBLY UNIT FOR JAGUAR E TYPE SER FIXED HEAD COUPE 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL 4, , x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS x MRE112C/D TRANSMISSION TUNNEL SIDE PANELS x MRE115 TUNNEL STIFFENER x MRE117LH/RH STIFFENERS x MRE118ALH CLOSING PANEL LH x MRE118ARH CLOSING PANEL x MRE14LH/RH FULL FLOOR x MRE15LH/RH INNER SILLS x MRE19 FRONT STIFFENERS x MRE20LH/RH REAR STIFFENERS x MRE25A CROSSMEMBER TO FULL FLOOR x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD x MRE29BLH/RH INN ARCH LH x MRE2LH/RH BHD TO SILL x MRE30LH/RH DOOR SHUT PANEL FHC x MRE3RH BULKHEAD PANEL x MRE42 CLOSING PANEL SER x MRE4LH BULKHEAD PANEL x MRE58 UPPER FLOOR x MRE59LH/RH FLOOR STIFFENER BRACKETS x MRE60 TUNNEL ASSEMBLY x MRE61 TOP PANNEL REAR FLOOR x MRE62 PANEL TO BOOT FLOOR x MRE63 PANEL ASSEMBLY x MRE72LH/RH REAR CHASSIS LEGS x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) x MRE76ALH/RH INN SHUT RH/LH x MRE78LH/RH INN VALANCE LH x MRE96B REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR NUMBER PLATE PANEL ETC SER.1 FHC 2 x MRE9ARH/ALH FRONT INNER BULKHEAD PABEL x MRE9BLH/BRH INNER BULKHEAD PANEL SIDE x MRE43 REAR CLOSING PANEL Bulkhead 4, Parts Total Excl Bulhead 5, Labour For Assembly 3, Total Sub Assembly Cost 13, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 8, SUB ASSEMBLY WITH BULKHEAD 13, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

13 SUB ASSEMBLY UNIT FOR JAGUAR E TYPE SER FIXED HEAD COUPE 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL 4, , x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS x MRE112C/E TRANSMISSION TUNNEL SIDE PANELS x MRE115 TUNNEL STIFFENER x MRE117LH/RH STIFFENERS x MRE118ALH CLOSING PANEL LH x MRE118ARH CLOSING PANEL x MRE14LH/RH FULL FLOOR x MRE15LH/RH INNER SILLS x MRE19 FRONT STIFFENERS x MRE20LH/RH REAR STIFFENERS x MRE25A CROSSMEMBER TO FULL FLOOR x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD x MRE29BLH/RH INN ARCH LH x MRE2LH/RH BHD TO SILL x MRE32LH/RH DOOR SHUT PANEL FHC x MRE3RH BULKHEAD PANEL x MRE4LH BULKHEAD PANEL x MRE58 UPPER FLOOR x MRE59LH/RH FLOOR STIFFENER BRACKETS x MRE60 TUNNEL ASSEMBLY x MRE61 TOP PANNEL REAR FLOOR x MRE62 PANEL TO BOOT FLOOR x MRE63 PANEL ASSEMBLY x MRE72LH/RH REAR CHASSIS LEGS x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) x MRE76ALH/RH INN SHUT RH/LH x MRE78LH/RH INN VALANCE LH x MRE96C REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR NUMBER PLATE PANEL ETC SER.1 FHC 2 x MRE9ARH/ALH FRONT INNER BULKHEAD PABEL x MRE9BLH/BRH INNER BULKHEAD PANEL SIDE x MRE43 REAR CLOSING PANEL Bulkhead 4, Parts Total Excl Bulhead 5, Labour For Assembly 3, Total Sub Assembly Cost 13, ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding. This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD 8, SUB ASSEMBLY WITH BULKHEAD 13, shown for illustration only. Unit Fitted With Inner Sill Reinforcings

14 ALPHA PANEL KIT SERIES & 4.2 ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44A REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X MRE98LH/RH REAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS Total Excluding VAT 2, % Total Inc. VAT 2, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

15 ALPHA PANEL KIT SERIES & 4.2 FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44 REAR TONNEAU PANEL X MRE75ALH REAR OUTER WING X MRE75ARH REAR OUTER WING X MRE98LH/RH REAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS Total Excluding VAT 2, % Total Inc. VAT 2, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

16 ALPHA PANEL KIT SERIES ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44C REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X BD35684/3 REAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD35620/1 MOUNTING BRACKETS Total Excluding VAT 2, % Total Inc. VAT 2, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

17 ALPHA PANEL KIT SERIES FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44B REAR TONNEAU PANEL X MRE75ALH REAR OUTER WING X MRE75ARH REAR OUTER WING X BD35683/4 REAR LIGHT FILLETS X BD19339 FUEL FILLER BOX X BD35620/1 MOUNTING BRACKET Total Excluding VAT 2, % Total Inc. VAT 2, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

18 BETA PANEL KIT SERIES & 4.2 ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44A REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X MRE98LH/RH RREAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS X MRE79ALH/RH DOOR COMPLETE , X MRE104A BOOTLID Total Excluding VAT 4, % Total Inc. VAT 4, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

19 BETA PANEL KIT SERIES & 4.2 FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44 REAR TONNEAU PANEL X MRE75ALH REAR OUTER WING X MRE75ARH REAR OUTER WING X MRE98LH/RH RREAR LIGHT FILLETS X BD19339 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS X MRE79BLH/RH DOOR COMPLETE Total Excluding VAT 3, % Total Inc. VAT 4, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

20 BETA PANEL KIT SERIES ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44C REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X BD35684/4 REAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD35620/1 MOUNTING BRACKETS X MRE79CLH/RH DOOR COMPLETE x MRE104A BOOT LID Total Excluding VAT 4, % Total Inc. VAT 4, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

21 BETA PANEL KIT SERIES FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44B REAR TONNEAU PANEL X MRE70LH/RH TOP PANEL TO HOOD X MRE75ALH REAR OUTER WING X MRE75ARH REAR OUTER WING X BD35684/3 REAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD35620/1 MOUNTING BRACKETS X MRE79DLH/RH DOOR COMPLETE Total Excluding VAT 4, % Total Inc. VAT 4, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

22 DELTA PANEL KIT SERIES & 4.2 ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44A REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X MRE98LH/RH RREAR LIGHT FILLETS X BD15933 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS X MRE79ALH/RH DOOR COMPLETE X MRE104A BOOTLID X BD36166 BONNET COMPLETE Total Excluding VAT 9, % 1, Total Inc. VAT 11, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

23 DELTA PANEL KIT SERIES & 4.2 FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE X MRE44 REAR TONNEAU PANEL X MRE75ALH REAR OUTER WING X MRE75ARH REAR OUTER WING X MRE98LH/RH RREAR LIGHT FILLETS X BD19339 FUEL FILLER BOX X BD MOUNTING BRACKETS X BD MOUNTING BRACKETS X MRE79BLH/RH DOOR COMPLETE X MRE104A BOOT LID ASSEMBLY X BD36166 BONNET COMPLETE Total Excluding VAT 9, % 1, Total Inc. VAT 11, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

24 DELTA PANEL KIT SERIES ROADSTER 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44C REAR TONNEAU PANEL X MRE67 TONNEAU TOP PANELS X MRE70LH/RH TOP PANEL TO HOOD X MRE75LH REAR OUTER WING X MRE75RH REAR OUTER WING X BD15933 FUEL FILLER BOX X BD35684/4 REAR LIGHT FILLETS X BD35620/1 MOUNTING BRACKETS X MRE79CLH/RH DOOR COMPLETE X MRE104A BOOT LID ASSEMBLY X BD36788 BONNET COMPLETE Total Excluding VAT 9, % 1, Total Inc. VAT 11, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

25 DELTA PANEL KIT SERIES FIXED HEAD COUPE 2 X MRE1LH/RH SILL END CLOSING PANELS X MRE2LH/RH BULKHEAD TO SILL PANELS X MRE5-6 BATT-AIR CLEANER MTG BKTS X MRE9LH/RH BULKHEAD SIDE PANELS X MRE17LH/RH OUTER SILLS X MRE44B REAR TONNEAU PANEL X MRE75ALH REAR OUTER WING X MRE75ALH REAR OUTER WING X BD19339 FUEL FILLER BOX X BD35620/1 MOUNTING BRACKETS X MRE79DLH/RH DOOR COMPLETE X BD36788 BONNET COMPLETE Total Excluding VAT 9, % 1, Total Inc. VAT 11, ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE

26

27

28