Tap-radio a new Eltako Wireless Building System Technology

Transcription

1 YEARS OF INNOVATION Tap-radio a new Eltako Wireless Building System Technology With the reliable and worldwide standardized EnOcean wireless technology in 868MHz. Easy to teach in the wireless pushbuttons with the new Eltako tap-radio technology and clear actuator functions without rotary switches. Even less expensive sensors and actuators. New EnOcean IP controller and new EnOcean IP camera for low-cost connection to the new GFA2 app. Subsequent teach-in of other sensors with no need for manual intervention in the actuators and only use of the new Eltako tap-radio technology. Compatible with standard wireless programme without encryption. Switching on the future

2 This is how tap-radio works 2 After connecting the tap-radio actuator and switching on the supply voltage or plugging the adapter actuator into the socket the related wireless pushbuttons can be taught in on this actuator by tapping the pushbutton within 2 minutes per pushbutton. Light, dimming and Venetian blind actuators: tap briefl y 3 times for use as a universal pushbutton, 4 times briefl y for use as a direction pushbutton, 5 times briefl y for use as a central control pushbutton On, 6 times briefl y for use as a central control pushbutton Off. Every teach-in and start and end of teach-in standby is confi rmed by short fl ashing or fl ickering, if a lamp or a motor is connected. If no action takes place for two minutes, teach-in ends automatically. But beforehand, block any further teach-in by tapping a taught in wireless pushbutton 3 times briefly and once long (>1 second) to prevent any accidental teach-in. Then the next tap-radio actuator can be connected, taught in and blocked without affecting the previous one connected. If you want to change the taught in device later or teach in other sensors, you can activate the block function again: after the supply voltage is switched on/off by a taught-in wireless pushbutton, but not by a central control pushbutton, tap briefl y 4 times and once long (>1 second). The wireless dimming actuators are universal dimming actuators in the factory setting and they dim depending on the connected load with leading or trailing edge. With various LED lamps, the dimming function improves when dimming takes place with leading edge dimming. Leading edge dimming is defi ned by tapping 5 times briefl y and once long (>1 second). The factory setting is reset by tapping 6 times briefl y and once long (>1 second). The TF-FKE window contacts and wireless pushbuttons are also taught in into the TF61R-230V relay actuator by briefl y tapping the contact 3 times to generate an NO contact or briefl y tapping the contact 4 times to generate an NC contact. TF-FKB window contacts are taught in by their magnets: tapping 3 times briefl y to generate an NO contact or tapping 4 times briefl y to generate an NC contact. Blocking and unblocking as for the other actuators. Virtual pushbuttons from the GFVS software are taught in by special wireless telegrams saved there.

3 Contents 3 Tap-radio a new Eltako Wireless Building System Technology 1-way wireless pushbutton TF-1FT 4 4-way wireless pushbutton TF-4FT 4 8-way wireless mini hand-held transmitter TF-8FM 5 Wireless window contact with energy generator TF-FKE 5 Wireless window contact TF-FKB 5 Wireless motion sensor TF-BSB 6 Wireless humidity temperature sensor TF-FTSB 6 Wireless thermo hygrostat TF-UTH 7 Wireless light actuator adapter TF100L-230V 8 Wireless universal dimming actuator adapter TF100D-230V 8 Wireless signal generator adapter TF100A-230V 8 Wireless light actuator TF61L-230V 9 Wireless universal dimming actuator TF61D-230V 9 Wireless shading element and roller shutter actuator TF61J-230V 9 Wireless relay actuator TF61R-230V 9 EnOcean IP controller TF-IP-Con 10 Wireless EnOcean IP camera TF-IP-Cam 10 Wireless repeater adapter TF100R-230V 11 Rocker for frames 55x55mm TF-W-4FT55 11 Double rocker for frames 55x55mm TF-DW-4FT55 11 The Eltako wireless sytem works with the reliable and wolrdwide standardized EnOcean wireless technology in 868MHz. It transmits ultra short and interference-proof signals with a range of up to 100 meters in halls. Eltako wireless pushbuttons reduce the electrosmog load since they emit high-frequency waves that are 100 times weaker than conventional light switches. There is also a signifi cant reduction in low-frequency alternating fi elds since fewer power cables need to be installed in the building. Tap-radio is a registered trademark of Eltako.

4 Tap-radio Sensors 4 TF-1FT Tap-radio wireless pushbutton 1-way wireless flat pushbutton for single mounting 84x84x16mm or mounting into the E-design switching system. Generates the power for wireless telegrams itself when the button is pressed, therefore there is no connecting wire and no standby loss. Wireless pushbuttons with one rocker can send one analysable signal. Press the bottom of the rocker near the mark. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. TF-1FT 1-way wireless pushbutton EAN ,50 /pc. TF-4FT Tap-radio wireless pushbutton 4-way wireless pushbutton pure white glossy for single mounting 84x84x16mm or mounting into the E-design switching system. Generates the power for wireless telegrams itself when the button is pressed, therefore there is no connecting wire and no standby loss. Pushbutton with rocker The scope of supply comprises a rocker and a double rocker. Wireless pushbuttons with one rocker can transmit two evaluable signals: press rocker up and press rocker down. Wireless pushbuttons with double rocker can transmit four evaluable signals: press two rockers up or down. The mounting base can be screwed onto a flat surface or glued to the wall, on glass or on furniture using the enclosed adhesive foil. Use the sleeves in the 55mm socket box for screw mounting. The double rocker is snapped onto the wireless module at the factory. If the double rocker is replaced by the large rocker, remove the rocker halves by pulling off to the front. Do not bend towards the middle. Then snap the large rocker so that the markings 0 and I on the back line up with the same markings on the wireless module. Pushbutton with double rocker TF-4FT 4-way wireless pushbutton EAN ,90 /pc.

5 Tap-radio Sensors TF-8FM Tap-radio mini hand-held transmitter 8-way wireless mini hand-held transmitter, pure white, with 8 buttons for 8 different pushbutton telegrams. 85x45x18mm, weighs only 60 grams. Generates the power for wireless telegrams when a button is pressed, therefore no standby loss. The buttons are lasered with the numbers 1 to 6 and the symbols for Central ON and Central OFF. 5 TF-8FM 8-way wireless mini hand-held transmitter EAN ,20 /pc. TF-FKE Tap-radio window contact Wireless window contact with energy generator 48x32x11.5mm, pure white. Also to monitor drawers and other moving devices. Generates the power for wireless telegrams itself when the lever is pressed, therefore there is no battery, no connecting wire and no standby loss. A wireless telegram is sent on closing and opening. Evaluation via tap-radio relay actuator TF61R-230V, EnOcean Controller TF-Con, GFVS-Safe II, GFVS-Touch etc. Mounting with the delivered adhesive foil, by screwing or with the delivered mounting bracket. The 48mm long lever can be shortened to 27mm by removing a part. TF-FKE Wireless window contact EAN ,60 /pc. PL-SAM1L TF-FKB Tap-radio window contact Wireless window contact with battery 75x25x12mm, pure white glossy. Magnet 37x10x6mm, pure white. When a contact is closed and opened, a different wireless telegram is sent and a status telegram is also sent approx. every 20 minutes. Evaluation via tap-radio relay actuators TF61R-230V, tap-radio shading element actuator TF61J-230V, EnOcean Controller TF-Con, GFVS-Safe II, GFVS-Touch etc. TF-FKB Wireless window contact EAN ,10 /pc.

6 Tap-radio Sensors 6 TF-BSB Tap-radio motion sensor Wireless motion sensor pure white glossy for single mounting 84x84x27mm or mounting into the E-design switching system. With battery. At factory settings, taught in light and dimming actuators turn off automatically 5 minutes after the last detected motion. Switching on the light by pushbutton. With a jumper it is possible to activate the automatic switching on by motion detection. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Set of 2 stainless-steel countersunk screws 2.9x25mm and plugs 5x25mm are enclosed. TF-BSB Wireless motion sensor EAN ,70 /pc. TF-FTSB Tap-radio humidity temperature sensor Wireless humidity temperature sensor pure white glossy for single mounting 84x84x20mm or mounting into the E-design switching system. With battery. The humidity temperature sensor measures constantly the relative humidity between 0 and 100% (±5%) and the temperature between -20 and +60 C (±0.5 C). The wireless humidity temperature sensor sends every 10 minutes a data telegram to the Eltako wireless building system. This interval can be reduced to 5 minutes by changing the position of the jumper, as described in the operating instructions. Evaluation over the EnOcean controller TF-Con, GFVS-Safe II, GFVS-Touch, etc. with the Eltako wireless app GFA2. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Set of 2 stainless-steel countersunk screws 2.9x25mm and plugs 5x25mm are enclosed. TF-FTSB Wireless humidity temperature sensor EAN ,40 /pc.

7 Tap-radio Sensors TF-UTH Tap-radio clock thermo hygrostat Wireless clock thermometer and -hygro stat with display for single mounting 84x84x20mm or mounting into the E-design switching system. Illuminated display. Only 0.2 watt standby loss. With adjustable day and night reference temperatures and relative humidity. Preset ready to operate. Power supply 230V. A 20cm long blue/black connecting wire is routed to the rear. Ca. 7 days power reserve. We recommend stainless-steel countersunk screws 2.9x25mm, DIN 7982 C, for screw connections. Both with rawl plugs 5x25mm and with 55mm switch boxes. Set of 2 stainlesssteel countersunk screws 2,9x25mm and plugs 5x25mm are enclosed. Up to 60 timer memory locations are freely assigned to the channels. With date and auto matic summer/winter time change over. The wireless clock thermostat sends a message to the Eltako wireless network every 50 seconds when there is an actual temperature change of minimum 0.3 C or a change in humidity of 5%. A change in reference temperature or relative humidity is sent immediately. If there is no change, a status report is sent every 10 minutes. Queries of a wireless small actuator FKS which are received approximately every 10 minutes will be answered immediately. Settings are made with the buttons MODE and SET and can be locked. A complete switching programme is preset and can be very easily changed. The factory setting for night temperature is 18 C. Set language: Every time the power supply is applied, press SET within 10 seconds to set the language german or english and press MODE to confirm. The normal display then appears: Weekday, date, time, actual temperature from 0 C to +40 C to one decimal point and relative humidity. To adapt the sensor to the ambient conditions, the internal sensor can be adjusted to the actual room temperature and humidity according to the operating instructions. If the settings are locked, the reference temperature set-temp. can be displayed and changed here from +8 C to +40 C in steps of 0.5 C by pressing MODE followed by SET. Rapid scroll: In the following settings, the numerals scroll rapidly when you press and hold down Enter. Release then press and hold down to change the scroll direction. Teaching-in actuators according to the operating manual. Different actuators as well as small actuators FKS can be taught-in. In combination with FKS also window/door contacts FTK and Hoppe window handles. As long as one or more window is open, the temperature is reduced to the frost protection temperature (8 C). Lock settings: Briefly press MODE and SET together and at lock, press SET to lock. This is displayed by an arrow next to the lock symbol. Unlock settings: Press MODE and SET together for 2 seconds and at unlock press SET to unlock. Manual activation of the reduced night temperature: press MODE and SET together during 4 seconds. Deactivation of the regulation: press MODE and SET together during 10 seconds. 7 TF-UTH Wireless clock thermo hygrostat with display pure white glossy EAN ,20 /pc.

8 Tap-radio Actuator Adapters 8 TF100L-230V Tap-radio light actuator adapter Wireless light actuator adapter 10A/250V AC. 100x55x45mm (measurements without plug), pure white glossy. Impulse switch with NO contact. 230V incandescent lamps and halogen lamps 1000W, ESL and 230V LED lamps up to 200W. Standby loss only 0.8 watt. Adapter for German fused safety sockets with increased shock protection. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and motion sensors TF-BSB as well as bidirectional wireless can be taught in using easy tap-radio technology. TF100L-230V Wireless light actuator adapter EAN ,70 /pc. TF100D-230V Tap-radio universal dimming actuator adapter Wireless universal dimming actuator adapter. 100x55x45mm (measurements without plug), pure white glossy. With power MOSFET. 230V incandescent lamps and halogen lamps up to 300W, 230V LEDs up to 100W. No inductive (wound) transformers. With children's rooms and snooze function. No minimum load. Standby loss only 0.7 watt. Adapter for German fused safety sockets with increased shock protection. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and motion sensors TF-BSB as well as bidirectional wireless can be taught in using easy tap-radio technology. During teach-in, the dimming actuator can be set to phase control to permit optimum dimming for various LED lamps. TF100D-230V Wireless dimming actuator adapter EAN ,80 /pc. TF100A-230 V Tap-radio signal generator adapter Wireless signal generator adapter 10A/250V AC. 100x55x45mm (measurements without plug), pure white glossy. In addition to an internal acoustic signal generator, a plug-connected load flashes. 230V incandescent lamps and halogen lamps 1000W, ESL and 230V LED lamps up to 200W. Standby loss only 0.8 watt. Adapter for German fused safety sockets with increased shock protection. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and bidirectional wireless can be taught in using easy tap-radio technology. The acoustic signal generator can be deactivited. TF100A-230V Wireless signal generator adapter EAN ,40 /pc.

9 Tap-radio Actuators TF61L-230V Tap-radio light actuator Wireless light actuator 10A/250V AC, 45x45x18mm. Impulse switch with NO contact, not potential free. 230V incandescent lamps and halogen lamps 1000W, ESL and 230V LED lamps up to 200W. Standby loss only 0.8 watt. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and motion sensors TF-BSB as well as bidirectional wireless can be taught in using easy tap-radio technology. In addition the actuator can be locally controlled with a conventional 230V control pushbutton without glow lamp current. 9 TF61L-230V Wireless light actuator EAN ,10 /pc. TF61D-230V Tap-radio universal dimming actuator Wireless universal dimming actuator 45x45x33mm. With power MOSFET. 230V incandescent lamps and halogen lamps up to 300W, 230V LEDs up to 100W. No inductive (wound) transformers. With children's rooms and snooze function. No minimum load. Standby loss only 0.7 watt. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and motion sensors TF-BSB as well as bidirectional wireless can be taught in using easy tap-radio technology. In addition the actuator can be locally controlled with a conventional 230V control pushbutton without glow lamp current. During teach-in, the dimming actuator can be set to phase control to permit optimum dimming for various LED lamps. TF61D-230V Wireless dimming actuator EAN ,90 /pc. TF61J-230V Tap-radio shading element actuator Wireless shading element and roller shutter actuator 1+1 NO contact 4A/250V AC for a shading element motor. 45x45x18mm. Standby loss only 0.8 watt. Up to 24 wireless universal pushbuttons, wireless direction pushbuttons, wireless central control pushbuttons and bidirectional wireless can be taught in using easy tap-radio technology. In addition the actuator can be locally controlled with a conventional 230V control pushbutton without glow lamp current. TF61J-230V Wireless shading element actuator EAN ,90 /pc. TF61R-230V Tap-radio relay actuator Wireless relay actuator 10A/250V AC, 45x45x18mm. 1 NO contact or NC contact, potential free. Standby loss only 0.8 watt. Up to 32 wireless pushbuttons, wireless window contacts and bidirectional wireless can be taught in using easy tap-radio technology. In addition the actuator can be locally controlled using a conventional 230V control input. During teach-in, the contact function in idle state can be defined as NO contact or NC contact. Closes the contact with at least one open window; it can then activate extraction hoods etc. or generate an alarm. Opens the contact with at least one open window: it can then switch off heaters or air conditioners. TF61R-230V Wireless relay actuator EAN ,10 /pc.

10 Tap-radio Controller and Camera 10 TF-IP-Con Tap-radio EnOcean IP controller The EnOcean IP controller receives EnOcean signals from many Eltako sensors and actuators, in particular all tap-radio models, and permits highly encrypted access, both internally and externally, with the Eltako Wireless Building app GFA2 by smartphone or tablet. Ethernet connection of IP controller to local network. The intended use of the TF-IP-Con is the bidirectional communication with EnOcean wireless signals over Ethernet (TCP/IP). Scope of supply: TF-IP-Con, wall adapter power supply, 1x ethernet cable 2m RJ45, manual. Specifications: Processor: Intel X1021, memory: 1 GB DDR3 RAM + 4 GB emmc, LAN: 1x 10/100Mbit ethernet, integrated EnOcean-868MHz wireless module (TCM310) ESP3, power supply 5V, plastic housing (pure white glossy), dimensions: 165x70x35mm with slots for wall mounting and feet to put down, weight: 140 grams. The IP configuration is performed via the 'Eltako-IP-configurator' tool. This software is downloadable from the Eltako website. In preparation. TF-IP-Con EnOcean IP controller EAN ,00 /pc. TF-IP-Cam Tap-radio EnOcean IP camera The EnOcean IP camera receives EnOcean signals from many Eltako sensors and actuators, in particular all tap-radio models, and permits highly encrypted access, both internally and externally, with the Eltako Wireless Building app GFA by smartphone or tablet. With motion detector. Wired or wireless connection to the local area network. Measurements LxWxH: 60x64x130mm. With patch cable, mounting kit and 230V power adapter. Pure white glossy. In preparation. TF-IP-Cam Wireless EnOcean IP camera EAN ,70 /pc.

11 Tap-radio Accessories TF100R-230V Tap-radio repeater adapter Wireless repeater adapter level x55x45mm (measurements without plug), pure white glossy. Standby loss only 0.8 watt. Adapter for German fused safety sockets with increased shock protection. A repeater is only required if the building structure permits undisturbed reception or the distance between the sensor and actuator is too large. Only telegrams from sensors and actuators are received and sent with full transmit power, but not the telegrams of other repeaters. 11 TF100R-230V Wireless repeater adapter EAN ,70 /pc. TF-W-4FT55 Rocker pure white glossy Makes a visually matching 2-channel pushbutton from the frame of a conventional pushbutton with internal cut-out measurements of 55x55mm, the wireless module and the mounting plate of a TF-4FT pushbutton. TF-W-4FT55 Rocker for 55x55mm frame EAN ,40 /pc. TF-DW-4FT55 Double rocker pure white glossy Makes a visually matching 4-channel pushbutton from the frame of a conventional pushbutton with internal cut-out measurements of 55x55mm, the wireless module and the mounting plate of a TF-4FT pushbutton. TF-DW-4FT55 Double rocker for 55x55mm frame EAN ,90 /pc.

12 Tap-radio a new Eltako Wireless Building Technology Technical support: thuente@eltako.de Export Sales Manager: export@eltako.de Eltako GmbH Hofener Straße 54, D Fellbach info@eltako.de eltako.com tap-radio.com Picture credits: cover: hand pressing switch beachboyx10 - Fotolia.com - Composing Eltako 05/2016