Suspension Systems Catalogue 2013 / 2014

Transcription

1 CEILING&WALL SYSTEMS CI/SfB (35) Xy September 2012 Between us, ideas become reality Suspension Systems Catalogue 2013 / 2014

2 S UMMARY ARMSTRONG SUSPENSION SYSTEMS Armstrong s Philosophies 1 Armstrong s Commitment to the Environment 2 CE Marking 3 Armstrong Projects 4 The Range 5 TECHNICAL INFORMATION 6 22 Fire Tests 16 Load Capacity Matrix 20 PRODUCT RANGE DESIGN OPTIONS Axiom Transitions 22 Axiom Profiles 24 Axiom Classic Canopy 26 Axiom Knife Edge Canopy 28 Axiom Circle & Curved 30 Silhouette 15 XL 2 32 Interlude 15 XL 2 34 Microline 36 environment quality/ce marking product innovation service Designed for fast and easy installation GENERAL APPLICATIONS Prelude Prelude 24 XL 2 40 Prelude 24 TLX 42 Prelude Sixty 2 44 Prelude 35 XL 2 46 Bandraster 48 System Z 50 Drywall Grid System 52 CORRIDOR Drywall Grid System Shortspan 54 Prelude Sixty 2 55 SPECIFIC APPLICATIONS Clean Room 24 mm Grid System 56 Corrosive Resistant 24 mm Grid System 58 Seismic Solution 60 LongSpan System 62 PERIMETER TRIM AND ACCESSORIES Flexible Perimeter Trim 64 Perimeter Solutions Mineral Ceilings 66 Perimeter Solutions Metal Ceilings 68 Accessories

3 ARMSTRONG S PHILOSOPHIES TOTAL CEILING SOLUTIONS The suspension system product range forms an integral part of Armstrong s total ceiling solutions policy. Armstrong now offers its customers and specifiers a complete range of ceiling panels including mineral, soft fibre, wood and metal and a wider choice than ever of suspension systems. Armstrong can provide solutions for all elements in today s challenging construction environments. QUALITY Suspension systems are manufactured for Armstrong both by its joint venture company WAVE (Worthington Armstrong Venture) and through various alliances with other companies who are regarded as specialists in their fields of engineering. WAVE operates on a global basis, and brings to its various European operations world class practice on the most technologically advanced equipment. SERVICE Suspension systems are manufactured in three European plants, strategically located to serve all our European customers. Additionally, both Armstrong and WAVE can draw upon their global manufacturing capabilities for both speciality products and manufacturing support. In addition to WAVE s manufacturing sites, Armstrong stocks suspension systems in distribution centres throughout Europe. This allows our customers the convenience of mixed product shipments, combining suspension systems with other Armstrong ceiling products, optimising bulk shipments direct from their manufacturing locations. WAVE WAVE has three manufacturing locations in Europe, three in the USA including the facility in Aberdeen, Maryland which is one of the world s largest grid facilities, plus one in China. INTEGRATION Suspension systems are designed for integration with Armstrong's portfolio of ceiling products, mineral, soft fibre, metal, wood and special solutions. TEAM VALLEY STAFFORD VALENCIENNES MUNSTER MOSCOW BENTON HARBOUR ABERDEEN / MALVERN PONTARLIER MADRID RANKWEIL LAS VEGAS SHANGHAI MUMBAI Metal ceiling plants Mineral fibre plants Grid plants Distribution centres 1

4 ARMSTRONG S COMMITMENT TO THE ENVIRONMENT Our environmental efforts in the lifecycle of our products start with design. fi fi DESIGN Innovative design creates stronger sections. Reuse of waste materials Raw materials for ceilings are renewable and abundant in nature. Recycled content varies by product: Suspension system contain 25% postconsumer recycled content fi MANUFACTURING Suspension system Main Runners and Cross Tees are rotary stitched by a patented method to deliver extra strength and stability. All in process scrap is recycled back into the process. Suspension systems and panels are manufactured at several locations, thereby reducing transportation costs and environmental impacts associated with transportation. RECYCLE Suspension systems contain up to 25% postconsumer recycled content End of Life ceiling tile recycling scheme. INSTALLATION Integrate technology to reduce installation time. Optimised packaging material less waste on site. Up to 100% of the packaging is made from recycled material. fi In several countries, we support the recollection of packaging. RETHINK PRODUCTS Continuous development of innovative thin gauge products. fi fi WARRANTY ON USE A history of quality products. Various warranty options are available on ceilings systems. MAINTENANCE Minimal maintenance and easy to replace. Armstrong has an expanding portfolio of sustainable products, these include: > Hotdipped galvanised suspension systems provide superior resistance to rust and corrosion. fi 2

5 CE Marking What is it? CE stands for Conformité Européenne, which translated literally, means European Conformity. The CE mark is a products passport for entry into the EEA (European Economic Area) and indicates that the product complies with the requirements of the applicable European Directive. For construction products the European Directive is the Construction Products Directive (89/106/ EEC), however, this is being replaced by the Construction Products Regulations (305/2011/EU) which will come into full force on 1st July The CPD identifies the essential requirements for products (and total projects) such that they are fit for intended use as: mechanical resistance and stability; safety in case of fire; hygiene, health and environment; safety in use; protection against noise; energy economy and heat retention. For suspended ceilings, the way in which we must test and communicate performance for these essential requirements has been defined in EN Suspended Ceilings Requirements and Test Methods. What does this mean? This standard identifies how the ceiling components must be tested against the essential requirements to identify a performance classification. It also indicates how the manufacturer must ensure that their products maintain these levels of performance on an ongoing basis. On 1st July 2007, it became mandatory for all suspended ceilings and accompanying suspension systems (in the scope of EN 13964) to carry the CE mark and the accompanying essential requirement test information. Since 1st July 2007, nonce marked materials are no longer saleable into the EEA. BRE BUILDING RESEARCH ESTABLISHMENT At Armstrong, we re proud to be a recognised pioneer in green practices, with successful methods to produce environmentally preferable products, prevent pollution and reduce waste. We re the only UK mineral ceiling manufacturer with a BRE Ecopoint profile an external certification of our compliance with ISO and ISO standards. Our Ecopoint score in 2007 was 0.10, a significant improvement on 2004, and we re working on lowering it even further. 3

6 ARMSTRONG PROJECTS Armstrong World Industry (USA) Axiom Circle Canopy Uttoxeter Cinema (UK) Coloured Prelude 24 4

7 Concordia Hotel (IT) Axiom C Canopy Dutch Technology Leiden (NL) System Z Medis Office (SI) Silhouette Hospital Ruzomberok (SK) Clean Room Grid. Telefonica Center (SP) Bandraster Lothar Meyer School (DE) 5

8 THE SUSPENSION RANGE The suspension systems include a full range of solutions for all ceiling suspension requirements. General applications, a range of standard Prelude 24mm and Prelude 15mm grid systems, Bandraster and Prelude Sixty 2 for longer spans. Drywall Grid Systems are available for plasterboard ceilings. Designer options including the minimalist grid Silhouette, Microline, Interlude and the Axiom range. Specific applications, for clean room and higher humidity environments. Perimeter trims and accessories, for most applications. We also include our comprehensive programme of special size options that is available in most ranges. A range of either stab or hook systems are available to meet the mechanical preferences of the installer. To complete the portfolio we also offer a technical test programme that provides fire, loadings and environmental accreditation. Suspension systems are designed for use with a wide variety of Armstrong ceiling products, mineral, soft fibre, metal, wood and special solutions. Peakform is an innovative design for Main Runners and Cross Tees. The taller Peakform profiles are engineered to create a stronger, more stable suspension system making installation both faster and easier. Superlock is an industry first stakedon clip for Main Runners which provides tighter, secure bulbtobulb connections; connections are confirmed by an audible click; Main Runners are easily disconnected and reconnected laterally

9 W HER E INNOVATION MEETS P ER F OR MANCE VOICE OF THE CUSTOMER Customer input is an extremely valuable part of our product innovation progress. Armstrong hold regular voice of customer work sessions to help develop the most innovative products and systems to meet the customer s needs. HOT DIPPED GALVINISED STEEL: Inhibits red rusting better and longer than electro galvanised or painted systems Installation of grid can start before the building is enclosed or HVAC system is operational. Long term system performance because entire system is hot dipped galvanised steel. THIN GAUGE TECHNOLOGY: Up to 50% lighter carton weight than the competition enables easier handling on site, plus the added benefit of the Peakform bulb allows easy cutting of the grid. OTHER SYSTEMS Our extensive range of performance grids also includes Bandraster, Prelude Sixty 2, Prelude 35, System Z and LongSpan. Specific grid solutions such as Clean Room Grid, Seismic Grid and Corrosive Resistant grid completes Armstrong's suspension solutions. PHYSICAL DETAIL All grids are made from doubleweb galvanised steel with a surface finish of baked polyester paint. STITCHING All Prelude components feature a unique stitched construction. The two metal layers of the vertical web are mechanically locked together in a sophisticated inline process. Stitching enhances the torsional resistance and general feel of the Prelude components. DESIGNER GRIDS Armstrong s designer range, Silhouette, Microline, Interlude, Axiom System and Axiom Canopies provide aesthetically enhanced grids. Silhouette creates a level ceiling surface, providing a flush appearance while Interlude gives a clean sophisticated visual that is created by the unique double reveal. Axiom Profiles and Transitions provide an aesthetic solution for changes in level and a flush transition with plaster margins. Axiom Canopies are a perimeter trim system designed to create ceiling clouds in conjunction with full size tiles. Microline is a steel based grid with aluminium extrusion. The exposed sleeve provides a clean and crisp visual plus a practical fluted reveal for flexibility in partition fixing and relocation. FULL RANGE OF ACCESSORIES AND PERIMETER SOLUTIONS Suspension systems are offered with a complete range of commonly required accessories and perimeter solutions. 7

10 AR MSTR ONG SYSTEMS PRELUDE UNIVERSAL MAIN RUNNER The Prelude Universal Main Runner supports the installation of either hook/butt cut or stab/override Cross Tees from one simple inventory of Main Runners. The universal system is available in Peakform design in both 24mm and 15mm widths. The Peakform Universal Main Runners feature a firm, quick and easy assembled Main Runner to Main Runner / bulbtobulb connection. Metric sized Main Runners are slotted at 100mm centres for more flexibility. Slots are machined to receive positive and accurate assembly of either Prelude TL and TLX (hook installation) or Prelude XL 2 (stab installation) Cross Tees. The stakedon Superlock clip allows for Main Runners to be disconnected and reconnected laterally in lowclearance areas or in the middle of a room. TL TLX PRELUDE XL 2 W HER E INNOVATION MEETS P ER F OR MANCE SEISMIC Rx SYSTEM Armstrong Seismic Rx System is a fully and independently tested approach to achieving ceiling installations that can withstand the forces associated with significant seismic activity or other severe events. In addition to earthquakes, there are several other industries with associated risks (e.g. Blast protection) where the use of Seismic Rx System will provide additional protection for the ceiling e.g. Nuclear installations Defence establishments Chemical installations Transport installations (with intermittent vibrations) The Seismic Rx system provides the additional security required for seismic resistance using specifically designed elements for minimised installation complexity with maximum performance

11 PRELUDE XL 2 CLICK INSTALLATION Prelude XL 2 Cross Tees in both 24mm and 15mm widths feature an advanced stab system that locates with an audible click, ensuring a solid installation at all times. The stab end is precision stamped from a separate piece of high grade steel permitting an increased accuracy and economy of production over the more conventional integral forming of the Cross Tee ends. A selected range of standard Prelude 15/24 XL 2 Cross Tees feature the new Peakform design. The Cross Tees are inserted to the right of each other through the Main Runner slots and easily pushed home. PRELUDE TLX TLX is a new highly engineered stakedon hook system, with a patented clip. Its unique steelbased composite material and shape provide a stronger and level connection, an improved fire performance and an increased overall stability.tlx Cross Tees are quicker and easier to cut due to the Peakform section. When the TLX Cross Tees are inserted to the right of each other through the Main Runner slots, the TLX clip provides a more secure installation. PRELUDE TL HOOK INSTALLATION Prelude TL Cross Tees in 15mm width feature an integrally formed hook nose. This popular installation system has been a feature of Armstrong suspension systems for over 20 years and its proven ease of assembly and precise butt cut joint has been a favourite of installers. Cross Tee alignment is ensured by locating the tees to the right hand side of the adjoining section. 9

12 STANDARD COLOURS Armstrong suspension system components are manufactured in a range of colours and metal finishes including Global White to complement Armstrong ceiling tiles. For complete information call Armstrong Technical Sales. GLOBAL WHITE SILVER GREY CARRARA PLATINUM BLACK WHITE GLOBAL WHITE BRASS CHROME WHITE GALVANISED BLACK/WHITE (GW) RAL 9006 (SG) (CA) (PN) (BK) RAL9010 (WR) (GW) (BS) (CE) RAL9010 (WR) Prelude 24 TLX Prelude 24 XL 2 Prelude 15 XL 2 /TL Silhouette XL 2 6mm Silhouette XL 2 3mm Interlude Bandraster Prelude 35 Prelude Sixty 2 Corrosive Resistant Clean Room Grid Axiom System Steel based capping Other than Steel based Painted perimeter trim items are available in Global White and capped angle T 1924 CA is available in all colours except black/white and galvanised. Please contact Armstrong Technical Sales Group for further details

13 COLOUR PALLET Stimulate your imagination to create vibrant interior spaces using custom colour solutions. Choice of more than 180 custom colours upon request. Available for Prelude 15 and Prelude 24 and specific perimeter trims. DETAILS 15 mm Cross Tee and Main Runner 24 mm Cross Tee and Main Runner 15mm 24mm Colour Selection Due to printing limitations, shade may vary from actual product. RAL 1000 RAL 1001* RAL 1002 RAL 1003 RAL 1004 RAL 1005 RAL 1006 RAL 1007* RAL 1011 RAL 1012 RAL 1013* RAL 1014 RAL 1015* RAL 1016 RAL 1017 RAL 1018 RAL 1019* RAL 1020 RAL 1021* RAL 1024 RAL 1027 RAL 1028 RAL 1032 RAL 1033 RAL 1034 RAL 2000* RAL 2001 RAL 2002* RAL 2003 RAL 2004* RAL 2008 RAL 2010 RAL 2011 RAL 2012 RAL 3000* RAL 3001 RAL 3002* RAL 3003 RAL 3004 RAL 3005 RAL 3007 RAL 3009 RAL 3011 RAL 3012 RAL 3013 RAL 3014 RAL 3015 RAL 3016 RAL 3017 RAL 3018 RAL 3022 RAL 3027 RAL 3031 RAL 4001 RAL 4002 RAL 4003 RAL 4004 RAL 4005 RAL 4007 RAL 4008 RAL 4009 RAL 5000 RAL 5001 RAL 5002 RAL 5003* RAL 5004 RAL 5005 RAL 5007 RAL 5008 RAL 5009* RAL 5010* RAL 5011 RAL 5012* RAL 5013 RAL 5014 RAL 5015* RAL 5018 RAL 5019 RAL 5020 RAL 5021 RAL 5022 RAL 5024 RAL 6000 RAL 6001 RAL 6002 RAL 6003 RAL 6004 RAL 6005 RAL 6006 RAL 6007 RAL 6008 RAL 6009 RAL 6010 RAL 6011* RAL 6012 RAL 6013 RAL 6014 RAL 6015 RAL 6016 RAL 6017 RAL 6018 RAL 6019 RAL 6020 RAL 6021 RAL 6022 RAL 6025 RAL 6026 RAL 6027 RAL 6028 RAL 6029 RAL 6032 RAL 7000 RAL 7001* RAL 7002 RAL 7003 RAL 7004 RAL 7005 RAL 7006 RAL 7008 RAL 7009 RAL 7010 RAL 7011 RAL 7012* RAL 7013 RAL 7015 RAL 7016* RAL 7021* RAL 7022 RAL 7023 RAL 7024 RAL 7026 RAL 7030* RAL 7031* RAL 7032* RAL 7033 RAL 7034 RAL 7035* RAL 7036 RAL 7037 RAL 7038* RAL 7039 RAL 7040* RAL 7044* RAL 8000 RAL 8001 RAL 8002 RAL 8003 RAL 8004 RAL 8007 RAL 8008 RAL 8011 RAL 8012 RAL 8014* RAL 8015 RAL 8016 RAL 8017 RAL 8019* RAL 8022 RAL 8023 RAL 8024 RAL 8025 RAL 8028 RAL 9001* RAL 9002* RAL 9003* RAL 9004 RAL 9005* RAL 9010* RAL 9011* RAL 9018* RAL 1023 RAL 2009 RAL 3020 RAL 4006 RAL 5017 RAL 6024 RAL 7042 RAL 7043 RAL 9016* RAL 9017 *Matt finish items are available as a special order. RAL CLASSIC: Important notice: This ORIGINAL RAL colour chart (card) has gone through stringent quality testing by RAL. Only the use of the individual cards of the registers RAL 840HR (semi matt finish) and RAL 841GL (gloss finish) will guarantee a reliable manufacture and control of RAL Colours. 11

14 PRODUCT SELECTOR by application areas Area Suspension system solution Open spaces Reception areas Meeting rooms / Individual offices Circulation areas Axiom Canopy (C/KE/Circle/Curved) Axiom Transitions Bandraster Axiom Transitions Axiom Profiles Silhouette 15 mm Microline 15 mm Interlude 15 mm Prelude 24 mm Prelude 15 mm System Z Microline 15 mm Prelude Sixty 2 Retail outlets / industrial manufacturing Prelude 35 XL 2 Humid areas Healthcare environments Prelude 24 Corrosive Resistant Clean Room Grid PRODUCT SELECTOR by edge detail compatibility Axiom Silhouette Interlude Microline Prelude Prelude Prelude Prelude Sixty 2 Prelude Clean Room Corrosive Bandraster System Z Transitions/ XL 2 24 TLX 35XL 2 Resistant Profiles Mineral Vector MicroLook MicroLook BE Tegular Board SL2 Metal Metal Axal Vector Metal MicroLook 8 Metal MicroLook 16 Metal Tegular 2 Metal Tegular 8, 11F or 16 Metal Board

15 TECHNICAL ICONS Colour Pallet Peakform Accessories Perimeter Trim Corridor Specific Applications/ Healthcare Environments Designer Grid General Applications 13

16 HEALTH AND CLEANLINESS Did You Know...? It s all about Air Quality control: The air penetrating the Clean Room can be filtered depending on the size of the undesired elements. Air can be recycled up to 60 times per hour for the total volume of the space. New air is also introduced to avoid a build up in the concentration of CO 2 and maintain enough oxygen for the people working there. Operators in a clean room have to wear equipment such as a clean room suit, caps, gloves, shoe protectors and masks. There are 2 types of rooms: rooms with overpressure, to avoid pollutants from entering (dust, bacteria, ) rooms with negative pressure, to avoid various contaminants from escaping to the outside (viruses, bacteria, spores, ). Building materials used in such spaces shall not have a negative impact on the pursuance of cleanliness and should preferably contribute actively to a better CLEAN ROOM A clean room is a space or a series of spaces where the concentration of particles is controlled in order to minimise the introduction, generation, retention of particles inside, generally for a specific industrial or research objective, as well as in healthcare environments. Parameters such as temperature, humidity and relative pressure are also maintained at a precise level, as defined in ISO Clean rooms are classified ISO 1 (cleanest) to ISO 9 depending on the number of particles measured. The performance is tested to ISO which determines the particle cleanliness class. Although US Federal Standard 209E has been officially withdrawn, it is continuously used as a reference. The following table shows the equivalence between the 2 standards. ISO Class Maximum Number of Particles in Air (particles in each cubic metre equal to or greater than the specified size) Particle size > 0.1µm > 0.2 µm > 0.3 µm > 0.5 µm > 1 µm > 5 µm ISO Class ISO Class ISO Class Class 1 ISO Class Class 10 ISO Class Class 100 ISO Class Class ISO Class Class ISO Class Class ISO Class Class HEALTHCARE PREMISE In healthcare premises, it is of critical importance to avoid hospital acquired infections. According to the level of risk, the necessary clean room performance will vary, generally between ISO 5 and ISO 8. All products below: can be used in ISO 5 environments and are certified against ISO ; inhibit growth of bacteria, moulds and yeasts tested against norms NF S 90351, France, and JIS Z2801, Japan. Some examples of spaces and system solutions: US Federal Standard 209E TYPE OF SPACE CONSTRAINTS SYSTEM SOLUTION* LEVEL OF PERFORMANCE Operating Theatre Fully airtight Metal Bioguard Plain ClipIn ISO 3 Flush surface finish with appropriate silicone or mastic joint High pressure water cleanable Antimicrobial MRI Nonmagnetic CLEAN ROOM grid with plastic ISO 5 holddown clips & Clean Room FL Antistatic Antimicrobial CLEAN ROOM grid with plastic ISO 5 holddown clips & Bioguard Acoustic Bioguard treatment Intensive Care Antimicrobial Clean Room grid with plastic holddown ISO 5 Recovery Room Good airtightness clips Bioguard Acoustic or Metal Bioguard Washable Maternity Good acoustical environment Extra Microperforated Rg 0701 with 0.65 w sound absorption Laboratory Premium B15 Pharmacy * Subject to local regulations. Please check with your Armstrong Technical Sales team

17 Did You Know...? System solutions for the pharmaceutical, food and manufacturing industry can be found in our brochure Solutions for Clean Room Environments. BIOGUARD products have been especially designed for the healthcare sector. The BIOGUARD paint treatment has additional active components which reduce the colony size of virulent strains of bacteria, moulds and yeasts. BIOGUARD products achieve ISO 5 to ISO 3 in accordance with ISO BIOGUARD paint has enhanced resistance to disinfectants. Grid and tiles for Clean Room environments Clean Room Bioguard Bioguard Clean Room FL Metal Bioguard Metal Bioguard Grid Plain Acoustic Extra Plain Microperforated Rg 0701 with Premium B15 Classification Zone 1, 2 & 3 Zone 1, 2 & 3 Zone 1, 2 & 3 Zone 1, 2 & 3 Zone 1, 2 & 3 Zone 1, 2, 3 & 4 NF S Particle ISO 4 ISO 5 ISO 5 ISO 5 ISO 5 ISO 3 cleanliness class Material Aluminium Mineral Mineral Mineral Steel with mineral Steel acoustic infill Surface PVC Bioguard paint Glass veil with Polyester film EXTRA PLAIN Bioguard paint MICROPERFORATED with Bioguard Rg 0701 with polyester powder Bioguard polyester paint powder paint Resistance Quaternary Ammonium, Hydrogen Peroxide, Chlorine * Quaternary Ammonium, to disinfectants* Hydrogen Peroxide, Chlorine * Not tested GRID MINERAL METAL 15

18 FIRE PERFORMANCES REACTION TO FIRE The harmonisation of technical standards within Europe, and the integration of EN13964 (Suspended ceilings requirements and test methods) into national legislation, means that there is now one series of harmonised European test methods and classifications for the reaction to fire of suspended ceilings. These new reaction to fire classifications, or Euroclasses, are defined in EN135011:2007. The Euroclasses have replaced the old national fire reaction ratings for showing the performance of ceilings in order to meet the Construction Products Directive and national building regulation requirements for internal linings. As reaction to fire is one of the essential safety requirements identified for suspended ceilings, the Euroclass classification is one of the mandatory elements on the CE mark for suspended ceiling tiles and grids. The Euroclasses rate from A1 through to F, with A1 being the best reaction to fire performance and F the worst. Each member state then sets the performance level required for different areas and building types within their own building regulations. Depending upon the reaction to fire test(s) conducted, the rating may include an additional classifications for smoke production and flaming droplets. Smoke and flaming droplets are regulated in some European countries. Smoke production is rated from s1 (the least smoke produced) to s3 (no limit to amount of smoke produced). Flaming droplets is rated from d0 (no flaming droplets) to d2 (no limit to flaming droplets). STRUCTURAL FIRE PROTECTION Throughout Europe, there is a requirement for a building s structure to be protected from fire. This is primarily for the structure to remain stable during a fire to allow the occupants to escape and also to enable fire fighters to work without threat of the building s collapse. The duration of the required protection will usually depend upon the height of, and location within, the building (i.e. typical floor, basement, roof construction etc), whether there is any active methods of fire protection (sprinklers etc) and the type of construction to be protected (steel beams, timber or mezzanine floors etc). A fire protecting suspended ceiling system is one of several important methods of providing the fire protection which fire degradable elements of the structure require. Ceilings can be used to enable a floor construction to meet the duration of protection required by the building regulations that it could not necessarily provide on its own. There are many national test methods for establishing the structural fire protection performance of a suspended ceiling system, as well as several European norms which are acceptable in most European countries. The performance achieved during testing will be classified in terms of the duration of protection given, typically this in accordance with EN135012:2007 for European tests. However, there is not yet one single European test method which is acceptable to all member states. Untested products may be assessed by reference to the product attributes and comparison to similar tested products, provided this is supported by an assessment report from a recognised fire expert and should be provided with the base test report that details how the product should be installed to achieve the assessed performance. The location and type of various service elements such as lighting fittings, smoke detectors etc, are infinite and the designer and installer must satisfy themselves that they can be integrated without reducing the tested performance of the ceiling system. This will usually require a test report from the fitting manufacturer or an assessment issued by the fire authorities. Without these documents the designer or installer may assume an everlasting responsibility for the fire safety of the building and occupants. The complete construction and assembly of the test installation is important to the success of the test, and Armstrong test many ceiling tiles for their structural fire performance, but always on Armstrong grid. There are many other details of the test construction that must be understood and adhered to. These include: main runner and hanger centres the type of top fixings and how the hangers are attached to them the minimum depth of the ceiling void what % of the floor design load is tested whether ceiling tile holddown clips were used. These details must be included in the installation if the tested performance is to be realised and they should be taken into account when writing specifications for ceilings intended to provide structural fire protection. In the UK the fire performance of floor structures protected by Armstrong ceiling tile and grid systems is given in the fire assessment document This document is based on a large number of fire tests conducted on various Armstrong ceiling tile and grid types. It provides an assessment of the performances attainable when various Armstrong tile and grid systems are installed in accordance with the appropriate base fire test and the permitted installation variations from that base test. The tables opposite give a summary of the performances achievable as stated in the assessment document and are correct at the time of going to print. As products may be modified or retested it is essential that their validity is always checked prior to installation. Therefore, the current version of the assessment document and the relevant base test report should always be consulted prior to the installation of a floor construction to be protected by an Armstrong ceiling system. A full document is always required and must be read and any limitations understood. Abridged versions must be regarded as undesirable as they will not show the full test details and construction. All Armstrong classification documents are freely available on request from the Armstrong Technical Sales team

19 Building Regulation performance table internal linings Building Regulations area (nonresidential) Euroclass Old classification A1 Noncombustible Circulation areas A2s3, d2 Limited Combustibility Bs3, d2 Class 0 Other Rooms (> 30 m 2 ) Class 1 Cs3, d2 Class 2 Small Rooms ( 30 m 2 ) Ds3, d2 Class 3 (Product cannot be used) Ed2, F Class 4 Assessed Performance Under Structural Steel Beams Base Test Report: (70995 for ClipIn) Board Tegular MicroLook Tegular 2 ClipIn 3mm Comments Ultima 90 minutes 60 minutes 60 minutes n/a n/a Includes 500 x 500 and 1200 x 300 MicroLook ULTIMA Ultima db 60 minutes 60 minutes 60 minutes n/a n/a Ultima OP 30 minutes n/a n/a n/a n/a Perla 60 minutes 60 minutes 60 minutes n/a n/a Bioguard Acoustic / Bioguard Plain 60 minutes 60 minutes 60 minutes n/a n/a Dune db 60 minutes 60 minutes 60 minutes n/a n/a Dune Supreme 60 minutes 60 minutes 30 minutes n/a n/a Fine Fissured 60 minutes 60 minutes 30 minutes n/a n/a Includes Colortone Black Plain 60 minutes 60 minutes 30 minutes n/a n/a Does NOT include GRAPHIS Cirrus 60 minutes 60 minutes 30 minutes n/a n/a Does NOT include any CIRRUS Design tiles Mezzanine DL minutes n/a n/a n/a n/a Metal Plain + Premium B15 or PAD 60 minutes 60 minutes 60 minutes 60 minutes n/a 8mm and 16mm returns. 18mm 100kg/m 3 AFBTF* pad Metal Standard Perforated Rg Premium B15 or PAD 60 minutes 60 minutes 60 minutes 60 minutes n/a 8mm and 16mm returns. 18mm 100kg/m 3 AFBTF* pad Metal Microperforated Rd Premium B15 or PAD 60 minutes 60 minutes 60 minutes 60 minutes n/a 8mm and 16mm returns. 18mm 100kg/m 3 AFBTF* pad Metal Extra Microperforated Rg Premium B15 or PAD 60 minutes 60 minutes 60 minutes 60 minutes n/a 8mm and 16mm returns. 18mm 100kg/m 3 AFBTF* pad Metal Plain + PAD n/a n/a n/a n/a 30 minutes 600 x 600 only. 40mm 45kg/m 3 AFBTF* pad Metal Standard Perforated Rg PAD n/a n/a n/a n/a 30 minutes 600 x 600 only. 40mm 45kg/m 3 AFBTF* pad Metal Microperforated Rd PAD n/a n/a n/a n/a 30 minutes 600 x 600 only. 40mm 45kg/m 3 AFBTF* pad Metal Extra MicroperforatedRg PAD n/a n/a n/a n/a 30 minutes 600 x 600 only. 40mm 45kg/m 3 AFBTF* pad Assessed Performance Under Timber Floors Base Test Report: Assessed Performance Under Mezzanine Floors Base Test Report: *AFTBF = an aluminium foil, black tissue faced acoustic pad Board Tegular MicroLook Tegular 2 ClipIn 3mm Comments Ultima 60 minutes 60 minutes 60 minutes n/a n/a Ultima db 60 minutes 60 minutes 60 minutes n/a n/a Dune db 60 minutes 60 minutes 60 minutes n/a n/a Main runners at 600mm centres only Dune Supreme 30 minutes 30 minutes n/a n/a n/a Mezzanine DL 100 n/a n/a n/a n/a n/a Fine Fissured n/a n/a n/a n/a n/a Ultima / Ultima db 30 minutes 30 minutes 30 minutes n/a n/a Perla 30 minutes 30 minutes n/a n/a n/a Sierra 30 minutes 30 minutes n/a n/a n/a Bioguard Acoustic / Bioguard Plain 30 minutes 30 minutes n/a n/a n/a Fine Fissured 30 minutes 30 minutes n/a n/a n/a Includes Colortone Black Plain 30 minutes 30 minutes n/a n/a n/a Does NOT include GRAPHIS Cirrus 30 minutes 30 minutes n/a n/a n/a Does NOT include any CIRRUS Design tiles Board Tegular MicroLook Tegular 2 ClipIn 3mm Comments Ultima / Ultima db 60 minutes 60 minutes 30 minutes n/a n/a Ultima db 60 minutes 60 minutes 30 minutes n/a n/a Dune db 60 minutes 60 minutes 30 minutes n/a n/a Dune Supreme 30 minutes 30 minutes n/a n/a n/a Mezzanine DL minutes n/a n/a n/a n/a Perla 30 minutes 30 minutes n/a n/a n/a Sierra 30 minutes 30 minutes n/a n/a n/a Bioguard Acoustic / Bioguard Plain 30 minutes 30 minutes n/a n/a n/a Fine Fissured 30 minutes 30 minutes n/a n/a n/a Includes Colortone Black Plain 30 minutes 30 minutes n/a n/a n/a Does NOT include GRAPHIS Cirrus 30 minutes 30 minutes n/a n/a n/a Does NOT include any CIRRUS Design tiles 17

20 INSTALLATION & MAINTENANCE SAFETY Armstrong s commitment on safety concerns each and every step of our business: in our plants & offices, we have implemented rigorous safety policies and procedures to help minimise risk for our products, for which we ensure compliance with appropriate European and local safety regulations. on the jobsite, safety is crucial for our partners: Armstrong therefore recommends the handling, installation & maintenance of our solutions in accordance with the European standards and /or local regulations, for the safety of the installers & of the end users. GENERAL ADVICE Installation of suspended ceiling systems should be carried out in accordance with Armstrong's current manufacturer's recommendations. For grid systems there are some specific points that should be considered: The appropriate type of Cross Tee for the ceiling tile edge detail must be considered. The grid systems should be installed in such a way that the loadbearing performance of the grid is not exceeded. 'Dynamic' service fittings should be independently supported so not to transfer vibration into the suspension system. Armstrong recommend the use of the 'ladder formation' and all our loading data is based on the 'ladder formation'. Using the 'Hformation' will give greater deflection for a given load. Ladder formation H formation Yes No

21 INSTALL ATION & MAINTENANCE 1 B A A 800 B Min 100 mm M 300 mm 1. Planning grid layout 2. Mark the perimeter trim lines 3. Installation of perimeter trims 4 Max 600 mm mm mm 1200 mm B (Main Runner) B (Main Runner) 4. Mark hanger positions 5. Installation of hangers 6. Positioning Main Runner slots Installation of Main Runners 8. Cross Tees installation right to right 9. Cutting Cross Tees A/B A/B 10. Installation of tiles 11. Measure and cut perimeter tiles 12. Retegulating Tegular or MicroLook tiles POST INSTALLATION After the installation of a suspended ceiling system it is important to ensure that it is properly maintained and that any additional works are not detrimental to the performance of the ceiling installation. Maintenance operations must only be undertaken after the technical impact on the ceiling system has been completely evaluated. For example, hangers should not be removed, adapted or bent without fully understanding the consequences and taking any appropriate mitigating actions. Armstrong suspension systems do not need any more maintenance than normal painted metal surfaces. However, if cleaning is required dust and superficial dirt can easily be removed with a soft brush or a vacuum cleaner with a brush attachment. For more stubborn marks a lightly dampened cloth or sponge can be used, although never use abrasive products. Some companies specialise in chemical cleaning solutions. These should only be undertaken after a test on a small hidden area of grid proves acceptable. Most Armstrong suspension systems can be redecorated, however, consideration should be given to the effect on the fire reaction performance of the grid. Ceiling tiles should be removed, however, the grid can usually be painted in situ. If a firm of professional decorators is used, assurances should be sought that the necessary performances will be maintained. It should be noted that any repainting would invalidate Armstrong's warranty for the product. For a copy of Armstrong's Suspension Systems Calculation Guide, please contact Armstrong Technical Sales. 19

22 LOAD CAPACITY MATRIX Loading is an important property of suspended ceiling grid systems both for the mechanical safety of the suspended ceiling and its visual appearance. In the EEA, table 6 of the suspended ceiling product standard, EN 13964:2004+A1:2006, defines 3 classes of deflection, the best being Class 1 which is L/500 (but no greater than 4mm). Class Maximun deflection in mm A 1 L B / 500 and not greater than 4,0 2 L B / No limit A The maximun deflection is the accumulative value of the deflection of the substructure component and the deflection of the membrane component. B L is the span in mm between the suspension components or the suspension points. The test method on which the European calculations of loadbearing capacity are based upon is also defined in EN 13964, and considers the influence of both deflection and bending moment. The individual product pages in the second half of this brochure include a table giving the maximum uniform distributed load, based on different hanger centres, in accordance with Class 1 deflection, as defined in EN 13964: A1:2006. For markets outside of the EEA different deflection limits are sometimes required. The tables on this page show the maximum uniform distributed load for the deflection limits shown, but taking into account deflection only. These values are calculated based upon load values determined from laboratory tests in accordance with the EN test method. For longer spans, some of the criteria shown on this page may give quite large deflection values. Armstrong recommends a maximum of 4mm deflection between points of suspension for all grid components, irrespective of span, for aesthetic reasons. Therefore the numbers in the tables on this page are the maximum loads permitted to meet the give a deflection criteria (such as L/400) but up to a maximum value of 4mm. System Load Summary (1200 x 1200 layout) Max Load kg/m 2 Deflection factor only System Main Runner Primary Secondary L/500 L/400 L/360 L/300 L/250 Cross Tee Cross Tee Prelude 24 XL A B A 13,3 16,8 18,8 22,7 22,7 Prelude 24 TLX A ,3 16,8 18,7 22,7 22,7 Prelude 15 XL A B B 13,1 16,5 18,5 22,3 22,3 Prelude 15 TL A A A 13,1 16,5 18,5 22,3 22,3 Microline CS WR CS WR CS WR Silhouette 15 XL G G G 11,4 14,4 16,1 19,5 19,5 Interlude 15 XL G G G 14,5 18,3 20,4 24,7 24,7 Prelude 35 XL ,9 17,7 19, Prelude 24 Corrosive Resistant TLX ,3 16,8 18,7 22,7 22,7 Clean Room 24 EA EA EA ,8 16,3 18,2 22,1 22,1 1200mm spacing 600mm mm Cross Tees MR MR

23 System Load Summary (1200x1800 layout) Max Load kg/m 2 Deflection factor only System Main Runner Primary Secondary L/500 L/400 L/360 L/300 L/250 Cross Tee Cross Tee Prelude 24 XL 2 (1800 span) A A A 6,5 7,3 7,3 7,3 7,3 Prelude 24 TLX (1800 span) A ,5 7,3 7,3 7,3 7,3 1200mm spacing 600mm mm Cross Tees MR MR System Load Summary (1800x1800 layout) Max Load kg/m 2 Deflection factor only System Main Runner Primary Secondary L/500 L/400 L/360 L/300 L/250 Cross Tee Cross Tee Prelude Sixty 2 24 XL G A A 6,5 7,3 7,3 7,3 7,3 Prelude Sixty 2 24 TLX G ,5 7,3 7,3 7,3 7,3 1800mm spacing 600mm 1800mm Cross Tees MR MR 21

24 Design Options AXIOM TRANSITIONS The 5 sections are designed to provide a flush transition between plaster margin and mineral, metal or wooden suspended ceilings. Axiom Transitions Item Nr. Description Dimensions Content / Carton Weight / Carton Cartons / Pallet length (mm) height (mm) pcs lm kg 50 8 T 3208 G (1) Axiom Transitions for ,00 11,80 36 Tegular/MicroLook T 3219 G (1) Axiom Transitions channel ,00 17, T 3215 G (1) Axiom Transitions angle ,00 15, T 3210 G (1) Axiom Transitions for ,00 11,80 36 Vector tiles T 3225 G (1) Axiom Transitions plasterboard ,00 11,30 36 perimeter trim Accessories for Axiom Transitions Item Nr. Description Dimensions Content / Carton Weight / Carton height (mm) pcs kg 79 mm A 321 G Axiom Transitions suspension clip straight ,10 62 mm A 322 G Axiom Transitions suspension clip angled ,10 A 340 G Axiom universal corner clip 100 2,10 A 338 G Axiom universal splice plate 100 2,10 A 339 G Axiom universal T bar connector clip 100 2,10 A 344 G Axiom universal hanging clip 100 2,10 (1) Also available in colour RAL 9010 (WR). Note: As Axiom is an aluminium extrusion it should not be used in ceiling assemblies where structural fire protection is required. All measurements in millimetres. All sizes are nominal

25 System Drawing AXIOM TRANSITIONS Design Options A 321 G A 322 G A 340 G A 338 G A 339 G 23

26 Design Options AXIOM PROFILES Available in 5 heights with a plasterboard trim section, Axiom Profiles are compatible with 24 mm and 15 mm grid systems including designer grid. Axiom Profiles 19 Item Nr. Description Dimensions Content / Carton Weight / Carton Cartons / Pallet length (mm) height (mm) pcs lm kg G (1) Axiom Profiles 50 mm ,00 7, G (1) Axiom Profiles 100 mm ,00 11, G (1) Axiom Profiles 150 mm ,00 14, G (1) Axiom Profiles 200 mm ,00 17, G (1) Axiom Vector Profiles 112 mm ,00 12,20 15 T 3213 H (1) Profile plasterboard trim , ,00 5,80 36 Accessories for Axiom Profiles Item Nr. Description Dimensions Content / Carton Weight / Carton height (mm) pcs kg A 334 G (1) Axiom Profiles corner post 50 mm ,30 A 335 G (1) Axiom Profiles corner post 100 mm ,50 A 336 G (1) Axiom Profiles corner post 150 mm ,70 A 337 G (1) Axiom Profiles corner post 200 mm ,90 A 345 G (1) Axiom Vector corner post 112 mm ,60 A 340 G Axiom universal corner clip 100 2,10 A 338 G Axiom universal splice plate 100 2,10 A 339 G Axiom universal T bar connector clip 100 2,10 A 344 G Axiom universal hanging clip 100 2,10 (1) Also available in colour RAL 9010 (WR)

27 System Drawing A 344 G A 334 G A 335 G A 336 G A 337 G A 345 G AXIOM PROFILES A 340 G A 344 G Design Options A 338 G A 339 G 200 A 100 (1) Also available in colour RAL 9010 (WR) 25

28 Design Options AXIOM C CANOPY Axiom C Canopy is a perimeter trim system designed to create ceiling clouds in conjunction with full size tiles. Made from standard ceiling panels and ready to assemble Axiom components, Axiom C Canopy will define and individualise any space. Axiom C Canopy Components Item Nr. Description G Axiom Vector MicroLook Tegular Profile 112 mm 112 mm C 3000 G Primary C channel A WDN 21 H T bar hanger Vector Tegular / MicroLook Cut to size Main Runner 600 mm XL 2 Cross Tees A 345 G Axiom Vector MicroLook Tegular Profile corner post 1.2m 3.0m 10 tiles 2.4m 1.8m 1.2m 8 tiles 6 tiles 4 tiles A 348 G Channel bracket 1.8m 15 tiles 12 tiles 9 tiles CA 97 G Clamp for C channel 2.4m 20 tiles 16 tiles A 347 G 24 mm XL 2 connector clip A 346 G 15 mm XL 2 connector clip 3.0m 25 tiles A 339 H Axiom universal T bar connector clip for cut tees with screws Axiom C Canopy Kits * Module Grid system 15 mm XL 2 Grid system 24 mm XL 2 Item Nr. Item Nr x 1200 mm AX 22 G15 AX 22 G x 1200 mm AX 32 G15 AX 32 G x 1800 mm AX 33 G15 AX 33 G x 1200 mm AX 42 G15 AX 42 G x 1800 mm AX 43 G15 AX 43 G x 2400 mm AX 44 G15 AX 44 G x 1200 mm AX 52 G15 AX 52 G x 1800 mm AX 53 G15 AX 53 G x 2400 mm AX 54 G15 AX 54 G x 3000 mm AX 55 G15 AX 55 G24 *Ceiling tiles are NOT included in the kit.! RECOMMENDATIONS Axiom C Canopy should always be installed in accordance with all applicable building codes and regulations. Axiom C Canopy should only be installed on a horizontal plane. They are not approved for exterior installations. Axiom C Canopy should always be installed by a minimum of 2 people. Read the installation instructions included in the carton carefully before starting the installation. Make sure the installation is clean and safe. Any additional weights (such as luminaires...) must be independently suspended from the soffit. Aircraft cables are included as a standard in the kit but if you require more lateral restraint, we would recommend the use of 6 mm threaded rod or provide diagonal bracing. All measurements in millimetres. All sizes are nominal

29 System Drawing The 1800 mm x 3000 mm module is used as an example only. An installation instruction guide is available. Please contact Armstrong Technical Sales for further details. AXIOM C CANOPY Design Options 4 Universal T bar connector clips 8 XL 2 connector clips 6 Aircraft cables & Gripple connectors 6 Universal T bar connector clips 4 Corner posts 4 Axiom profiles cut to size 6 Channel brackets 3 C channels cut to size 6 T bar hangers 12 Cross Tees 600 mm XL 2 (24 mm or 15 mm) 2 Main Runners cut to size (24 mm or 15 mm) OPTION 2 Quick hanger* OPTION 1 Aircraft cable & Gripple connectors OPTION 3 6 mm Threaded rod* * not included in the kit 27

30 Design Options AXIOM KE CANOPY Axiom KE Canopy is an aesthetic perimeter trim system designed to create ceiling clouds in conjunction with full size tiles. Made from standard ceiling panels and ready to assemble Axiom components, Axiom KE Canopy is a quick refurbishment solution, ideal for acoustically challenged or open plenum spaces. Axiom KE Canopy Components Item Nr. CS G Description Axiom KE Profile Tegular / MicroLook 106 mm C 3000 G A WDN 21 H Primary C channel T bar hanger 135 mm Cut to size Main Runner 600mm XL 2 Cross Tees Vector 106 mm CS 57 G Mitre corner piece 135 mm A 361 G Mitre corner splice connector 3.0m 2.4m 1.8m 1.2m A 348 G Channel bracket 1.2m 10 tiles 8 tiles 6 tiles 4 tiles CA 97 G Clamp for C channel 1.8m 15 tiles 12 tiles 9 tiles A 347 G 24 mm XL 2 connector clip A 346 G 15 mm XL 2 connector clip 2.4m 20 tiles 16 tiles A 339 H Axiom universal T bar connector clip for cut tees with screws 3.0m 25 tiles A 338 G Axiom universal splice plate Axiom KE Canopy Kits * Module Grid system 15 mm XL 2 Grid system 24 mm XL 2 Item Nr. Item Nr x 1200 mm CS AK 22 G15 CS AK 22 G x 1200 mm CS AK 32 G15 CS AK 32 G x 1800 mm CS AK 33 G15 CS AK 33 G x 1200 mm CS AK 42 G15 CS AK 42 G x 1800 mm CS AK 43 G15 CS AK 43 G x 2400 mm CS AK 44 G15 CS AK 44 G x 1200 mm CS AK 52 G15 CS AK 52 G x 1800 mm CS AK 53 G15 CS AK 53 G x 2400 mm CS AK 54 G15 CS AK 54 G x 3000 mm CS AK 55 G15 CS AK 55 G24 *Ceiling tiles are NOT included in the kit. All measurements in millimetres. All sizes are nominal.! RECOMMENDATIONS Axiom KE Canopies should always be installed in accordance with all applicable building codes and regulations. Axiom KE Canopies should only be installed on a horizontal plane. They are not approved for exterior installations. Axiom KE Canopies should always be installed by a minimum of 2 people. Read the installation instructions included in the carton carefully before starting the installation. Make sure the installation is clean and safe. Any additional weights (such as luminaires...) must be independently suspended from the soffit. Aircraft cables are included as a standard in the kit but if you require more lateral restraint, we would recommend the use of 6 mm threaded rod or provide diagonal bracing

31 System Drawing The 1800 mm x 3000 mm module is used as an example only. An installation instruction guide is available. Please contact Armstrong Technical Sales for further details. AXIOM KE CANOPY Design Options 4 Universal T bar connector clips 8 XL 2 connector clips 6 Aircraft cables & Gripple connectors 6 Universal T bar connector clips 16 Axiom universal splice plates 6 Channel brackets 6 T bar hangers 4 Mitre Corners 8 Corner splice connectors 12 Cross Tees 600 mm XL 2 (24 mm or 15 mm) 4 Axiom profiles cut to size 2 Main Runners cut to size (24 mm or 15 mm) 3 C channels cut to size OPTION 2 Quick hanger* OPTION 1 Aircraft cable & Gripple connectors OPTION 3 6 mm Threaded rod* * not included in the kit 29

32 Design Options AXIOM CIRCLE & CURVED The Axiom Circle & Curved Canopies are an aesthetic perimeter trim system designed to create ceiling clouds in conjunction with full size tiles. Made from standard ceiling panels and ready to assemble Axiom components, Curved and Circle Canopies allow specifiers to play with different planes and levels as well as conceal service elements. Axiom Circle & Curves Components Item Nr. Description G Axiom Circle and Curved Profile C3000 G Primary C Channel A Prelude Peakform Main Runner T15 or A Prelude Peakform Main Runner T B Prelude XL 2 Cross Tee 600 mm T15 or Tegular / MicroLook A Prelude XL 2 Cross Tee 600 mm T24 AWDN 21 H T bar hanger 1.8m Ø Canopy 1.8m x 2.4m Canopy 1.8m x 3m Canopy A 361 G Splice connector A 339 H Axiom universal T bar connector clip for cut tees with screws A 156 G Perimeter fillin for 15 mm grid 2.4m Ø Canopy 2.4m x 2.4m Canopy 2.4m x 3m Canopy A 246 G Perimeter fillin for 24 mm grid A 348 G Channel bracket CA 97 G Clamp for C Channel 3m x 3m Canopy Axiom Circle & Curved Kits * Module Grid system 15 mm XL 2 Grid system 24 mm XL 2 Item Nr. Item Nr. Circle 1800 CS ACI 33 G15 CS ACI 33 G24 Circle 2400 CS ACI 44 G15 CS ACI 44 G24 Curved 2400 x 1800 CS ACU 43 G15 CS ACU 43 G24 Curved 2400 x 2400 CS ACU 44 G15 CS ACU 44 G24 Curved 3000 x 1800 CS ACU 53 G15 CS ACU 53 G24 Curved 3000 x 2400 CS ACU 54 G15 CS ACU 54 G24 Curved 3000 x 3000 CS ACU 55 G15 CS ACU 55 G24 *Ceiling tiles are NOT included in the kit.! RECOMMENDATIONS Axiom Circle & Curved Canopies should always be installed in accordance with all applicable building codes and regulations. Axiom Circle & Curved Canopies should only be installed on a horizontal plane. They are not approved for exterior installations. Axiom Circle & Curved Canopies should always be installed by a minimum of 2 people. Read the installation instructions included in the carton carefully before starting the installation. Make sure the installation is clean and safe. Any additional weights (such as luminaires...) must be independently suspended from the soffit. Aircraft cables are included as a standard in the kit but if you require more lateral restraint, we would recommend the use of 6 mm threaded rod or provide diagonal bracing. All measurements in millimetres. All sizes are nominal