Vacuum & Pressure Sensors. Section C. Convum

Transcription

1 Vacuum & Pressure Sensors Secti vum 175

2 Index

3 Index Technical Informati MPS-1 MPS-2 MPS-3 MPS-31 MPS-6 MPS-7 MPS-8 MVS-201 MPS-3 Stainless MPS-5 Stainless P5V-SV Pressure Range Output Type Media Maximum IP Rating Hysteresis Output Mode Adjustment Output Setting Display Page Number 0 to 10 bar (1) NPN / PNP Air, Variable, 0 to -1 bar With Analog N-orrosive 65 3 to Trim Pot to 0,9 bar Gas 20% F.S. 0 to -1 bar Air, Variable, Push LED Display -1 to 5 bar (2) NPN / PNP N-orrosive % F.S. Butt (Red) Gas 0 to 10 bar Air, 0 to -1 bar (2) NPN / PNP N-orrosive 65 Variable, Push LED Display 0 to 1 bar Analog Opti Gas 100% F.S. Butt (Red) to 5 bar 0 to 10 bar Air, Variable, Push LED Display 0 to -1 bar (1) NPN / PNP N-orrosive % F.S. Butt (Red / Green) to 5 bar Gas 0 to 10 bar (1) NPN / PNP Air, 0 to -1 bar or (1) Analog N-orrosive 40 Trim Pot to 1 bar Gas Remote Panel: Use 71: (2) NPN/PNP Variable, Push LED Display with MPS-5,6,8 Analog Opti % F.S. Butt (Red) : (1) NPN/PNP 0 to -1 bar (1) NPN / PNP Air, Fixed, -1 to 5 bar or (1) Analog N-orrosive 40 < 2% F.S. Trim Pot Gas 0 to -1bar Air, Variable, Push LED Display -1 to 5 bar (1) NPN / PNP N-orrosive % F.S. Butt (Red) Gas Fluid, 0 to 10 bar (2) NPN / PNP N-orrosive 65 Variable, Push LED Display 0 to -1 bar Analog Opti to 316L or 100% F.S. Butt (Red) to 5 bar 630 SUS Fluid, 0 to 10 bar Analog N-orrosive 65 0 to -1 bar to 316L or SUS -0,15 to -0,9 bar Air, 20% of N-orrosive preset value Gas Accessories

4 Technical Informati Solid State Sensors Introducti Electromechanical pressure sensors cvert the applied pressure to an electrical signal. When pressure is applied, the diaphragm is deflected causing the diffused resistors to change resistance (piezoelectric effect), which yields an electrical signal proportial to the pressure change. Applicatis for pressure switches are numerous and important in today's high-tech manufacturing envirment. Difference Between Switch Output and Analog Output Type Switch Output This is an NPN / PNP Open ollector transistor Output that sinks or sources the signal when the pressure switch point is achieved. The switch point is set by programming or potentiometer trimmer adjustment. Silic Diaphragm This type of sensor is used for air and n-corrosive gas applicatis. 0 h H off off Sensor Module -1 bar Silic Diaphragm Base Window omparator Window omparator provides two switch points at different pressures to activate the NPN / PNP open collector transistor outputs. Pressure Stainless Steel Diaphragm This type of sensor is used for liquids, n-corrosive to 316L or 630 stainless steel. Semicductor Pressure Element A b -1 bar 0 Analog Output off off off An analog output provides an output voltage that is proportial and linear to the pressure measured by the sensor. This output signal provides ctinuous feedback to the analog card of the PL. Analog Output Body SUS 316L Stainless Steel Diaphragm SUS 316L or SUS 630 Output (ma) 20 4 Output (Volts) 5 1 Pressure 0 0 Max. Rating Pressure

5 Technical Informati Difference Between NPN and PNP Output NPN NPN type open collector transistor outputs are solid state circuits that provide sinking output capabilities. When the transistor is, the current for the load flows into the transistor. This output sinks toward 0 VD, 0 ma. NPN Output (With Analog Output) PNP PNP type open collector transistor outputs are solid state circuits that provide sinking output capabilities. When the transistor is, the current for the load flows out of the transistor. This output sources toward 24 VD, 125 ma. PNP Output (With Analog Output) D1 (Brown) +V D1 (Brown) +V Main ircuit Tr1 Tr2 ZD1 ZD2 1K ZD3 (Black) Out 1 (White) Out 2 (Pink) Analog Opti (Blue) O V Load Max. 125 ma D 1 to 5 V Load Max. 125 ma + D 10,8 V to 30 V Main ircuit Tr1 Tr2 ZD2 1K ZD3 ZD1 (Black) Out 1 (White) Out 2 (Pink) Analog Opti D 1 to 5 V (Blue) O V Max. 125 ma Load Load + D 10,8 V to 30 V NPN Output (With Reset IN) PNP Output (With Reset IN) D1 (Brown) +V Or Tr D1 (Brown) +V Or Tr Main ircuit Tr1 ZD1 Tr2 ZD2 (Pink) Digital IN Opti (Black) Out 1 (White) Out 2 (Blue) O V Load Load Max. 125 ma Max. 125 ma + D 10,8 V to 30 V Main ircuit Tr2 Tr1 ZD2 ZD1 (Black) Out 1 (White) Out 2 (Pink) Digital IN Opti (Blue) O V Max. 125 ma Max. 125 ma Load Load + D 10,8 V to 30 V Reset Input Opti By sending a 5 VD signal to the sensor, it is possible to automatically reset the sensor to ambient zero when small fluctuatis in the system or atmosphere influence the beginning reference point. Fluctuati Digital Set H OK Negative Pressure NG IN H Negative OK Pressure OK IN IN IN Flashing display of AL is displayed when the digital IN signal is entered

6 Technical Informati Output Modes Switch Point with Hysteresis Settings This output mode provides e switch point (H) and a hysteresis pressure adjustment. When the switch point pressure is achieved, the output (NPN / PNP) is activated if normally open or deactivated if normally closed. Typically, this mode is used for pressure cfirmati. For positive pressure applicatis, this operating mode does not provide any output or alarms beyd the switch point in the case of excessive pressures. The hysteresis setting (h) is the difference in pressure below the switch point pressure which ctrols the / off status of the output. h H 0-1 bar off Window omparator Setting off This output mode provides two switch points (A) and (b) that ctrol the output signals (NPN / PNP) between the two pressures. This creates a window that the sensor can provide an output and is sometimes referred to as high / low setting. The window comparator Mode provides an output or alarm when pressures exceed the upper limit. A b -1 bar 0 off off off Repeatability The repeatability refers to the sensor s ability to provide the same output with csecutive applicatis of the same pressure input. Repeatability Repeatability is represented as a percentage of the full scale value of the sensor. All Parker / vum sensors are rated ± 0,2% F.S. P 1 would be represented as 10 bar x 0,002 = ± 0,02 bar. Accuracy Reading The PERENTAGE difference between the true value and that indicated by an instrument is the measure of the instrument s accuracy. It is expressed as a percentage of the full-scale value of the reading according to the type of instrument. Display Resoluti The least possible unit increment shown the display. IP Ratings P1 Pressure IP40 - Protected against solid foreign objects of 0,04" (1 mm) and greater. N-protected against the penetrati of liquids. IP65 - Dust tight. Protected against water jets. IP67 - Dust tight. Protected against the effects of temporary immersi water. + Pressure Unit Table Units Units Pa bar PSI kgf/cm 2 atm mm H 2 O in H 2 O mm Hg in Hg Pa ,145x10-3 1,0197x10-5 0,987x10-5 0, ,402x10-2 0,750x10-2 0,295x10-3 bar ,5038 1, , ,16 401,46 750,062 29,53 PSI 6894,76 0, , , ,07 27,68 51,715 2,036 kgf/cm ,5 0, , , ,70 735,56 28,96 atm 1,013x10-5 1, ,696 1, , ,92 mm H 2 O 9,807 0,098x10-3 0, ,0001 0,097x ,0394 0, ,29x10-2 in H 2 O 249,09 0,249x10-2 0,0361 0, ,246x ,4 1 1,868 0,07355 mm Hg 133,322 0, , , , ,5951 0, ,0394 in Hg 3386,4 0, ,4912 0,0345 0, ,32 13,589 25,

7 Technical Informati Output 1 Output 2 Output 3 Output 4 Output Normally losed (Passing) Output Normally Open (N-Passing) Pressure Units (Pascal). Negative Units for Vacuum Sensors Pressure Units (Bar). Negative Units for Vacuum Sensors Pressure Units (in.hg). Negative Units for Vacuum Sensors Pressure Units (in.hg). Negative Units for Vacuum Sensors Pressure Units (kgf/cm 2 ). Negative Units for Vacuum Sensors Pressure Units (PSI) Easy Mode. Sensor will ly allow changes to set points Off, or Energy Saving Display; reduces current csumpti of Sensor On Hysteresis Mode. Select Hysteresis Set Point and Hysteresis Range Windows omparative Mode Select High and Low Set Point Hysteresis Mode Set Point. Output 1 Hysteresis Mode Set Point. Output 2 Hysteresis Mode. Hysteresis Range Output 1 Hysteresis Mode. Hysteresis Range Output 2 Windows omparative Mode Low Set Point Output 1 Windows omparative Mode High Set Point Output 1 Windows omparative Mode Low Set Point Output 2 Windows omparative Mode High Set Point Output 2 Automatic Teach Mode. Automatically sets Outputs 1 and 2 while cycling system. Output 1 set to Hysteresis Mode, Output 2 set to Window omparative Mode Auto Surveillance Mode On/Off. Set after Automatic Teach Auto Surveillance based cycles times. Provides output if Peak Value is not obtained in a specified number of cycles. (1-100) Display Refresh Setting. Display updates from 0,1 to 1 sec. 0,3 sec factory set. Does not affect Sensor Respse Time Output Respse Time. Multiples the sensor respse time. Increases sensor respse time. (Anti-chatter Mode) Zero Reset Pressure Value Display Mode. Displays Pressure for a specific time period and then updates for next time period Time Range for Pressure Value Display Mode Value Setting for Pressure Value Display Mode Display Peak Value over selected time range Display Bottom Value over selected time range Display Difference over selected time range Display Functi Mode. On/Off Display Functi. Selects display types. Display blinks pressure when Output 1 is Passing Normal when Output 1 is N-Passing Display blinks pressure when Output 2 is Passing Normal when Output 2 is N-Passing Display shows pressure when Output 1 is Passing Display shows special screen when N-Passing Display shows pressure when Output 2 is Passing Display shows special screen when N-Passing Select Switch Output setting for MPS-31 olor Setting for MPS-31 MPS-4, Port Reference Selecti MPS-4, Display change of B port to A port static MPS-4, Display change of A port to B port static MPS-4, Display change of A port to change of B port MPS-7, Pressure Range Selecti Vacuum MPS-7, Pressure Range Selecti Low Pressure MPS-7, Pressure Range Selecti Positive Pressure MPS-7, Pressure Range Selecti ompound Pressure MPS-7, Energy Savings Mode, reduces current csumpti MPS-7, Peak Surveillance Digital Input Sensors Only. Digital Input Mode for remote Zero reset of sensors Digital Input Digital hannel MPS-7 Scan Mode. Sensor scans and displays each channel for 3 sec. Locked. Sensor programs cannot be changed Unlocked. Sensor programs can be changed Sets Sensors reference point to current atmospheric cditis

8 MPS-1 Model Number Output Pressure Range MPS-V1G-P PNP 0 to -1 bar MPS-P1G-P PNP 0 to 10 bar MPS-V1E-P PNP 0 to -1 bar MPS-P1E-P PNP 0 to 10 bar Features MPS-1 Pressure Ranges: Vacuum... 0 to -1 bar Positive Pressure... 0 to 10 bar Sensor Outputs 1 Normally Open NPN or PNP Open ollector Transistor Output; 30 VD, 125 ma 1 Analog 1 to 5 VD Switch Output Adjusted with Potentiometer 3-Turn Trimmer Switch Hysteresis Adjusted with Potentiometer 3/4 Turn Trimmer Output Respse Time Less Than 2,5 Millisecds IP65 Rated and E Marked Air and N-orrosive Gases Output Modes The MPS-1 Series Sensor has two outputs, e open NPN or PNP switch output and e analog output. The Hysteresis Range (h) ctrols the output signal below the Switch Point (H). The Pressure Output Signal is a 3 turn trimmer that sets the switch point of the output. The hysteresis adjustment is a 3/4 turn trimmer to ctrol the output signal 3 to 20% below the pressure output signal. The Analog Output is a 1 to 5 VD signal calibrated to the pressure scale of the sensor. Switch Output 0 h off H -1 bar Analog Output Output (Volts) 5 1 Analog Output off 0 0 Max. Rating Pressure

9 MPS-1 Model Number Index MPS - V 1 G - P Pressure Range V 0 to -1 bar P 0 to 10 bar Port Size G 1/8" BSPP / M5F E Flange / M5F ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector M8 4-Pin MPS-L1G-P MPS-V1E-P Specificatis Media Air and N-orrosive Gases Pressure Port G: 1/8" BSPP, E: Flange Mount with M5 Female Proof Pressure V: 5 bar, P: 15 bar Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity 35 to 85% RH Electrical necti 4-Pin, M8 nector with Built-in LED Power Supply 10,8 to 30 VD, Ripple Vp-p 10% Max., Reverse Voltage Protecti Analog Output 1 to 5 VD ±0,04, Accuracy Linear 0,5% F.S. Switch Output N.O., Switch Output Mode with Hysteresis Adjustment Output ircuit NPN (Sinking), PNP (Sourcing) Open ollector Transistor 30 VA, 80 ma Switch Output Setting H 3-Turn Trimmer Hysteresis Setting h 3/4-Turn Trimmer (3 to 20% of Switch Output Setting) Respse Time < 2,5 ms Repeatability ±1% F.S. Thermal Error 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP65 or IP40, EM Rating : EN55011 lass B, EN urrent sumpti < 20 ma Spike Protecti 400 VP, 1 µs Dielectric Strength 1000 VA, 1 min. Insulati Resistance > 100 Mohms at 500 VD Vibrati Resistance 10 to 55 Hz, 1,5 mm, XYZ, 2 hrs. Shock Resistance 100 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass 30 g

10 MPS-1 Output Setting Switch Output Setting The Switch Point of the output signal is adjusted with a 3-turn potentiometer trimmer (S). To set the switch point pressure, rotate the trimmer clockwise to raise the switch pressure and rotate the trimmer counter clockwise to lower the switch pressure.! autis The MPS-1 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Potentiometer for the Switch Point Pressure and Hysteresis Range is sensitive. Excessive force or exceeding the limits of the trimmers may cause damage. Hysteresis Setting The Hysteresis setting is a 3/4 - turn potentiometer trimmer with a range of 3% to 20% below the switch point (S). Rotate the Hysteresis trimmer (H) clockwise to increase the Hysteresis range and rotate the trimmer counter clockwise to lower the Hysteresis range (h). A separate pressure gauge is necessary to accurately adjust these values. For best results, set the switch point (H) of the output signal before adjusting the hysteresis range. For fine tuning the hysteresis range, re-adjust the switch point (S) of the output signal. S H Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Installati Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb to a normal envirment with a 2 mm I. D. tube and install screw as shown. S H O-Ring Barb oupling S H -INLUDED- Screw Wiring Diagram Internal ircuit Pin # 1 Brown:24 VD 2 White: Analog 1 to 5 VD Output 3 Blue: 0 VD 4 Black: NPN / PNP Open ollector Output H H S 3 S 3 NPN (Sinking) PNP (Sourcing) Sensor Male Pin Out

11 MPS-1 Dimensis G M5Fx5 LED M3Fx4 2 Places 1/8" Male M8, 4-Pin M8 S H 21,2 G1/8M ,7 E Flange Mount M8, 4-Pin M3Fx5 4 Places M5Fx M4F 2 Places LED M8 S H M3Fx4 2 Places 21,2 24,7 10 1, ,7 Accessories Flange Bracket for V1E Type 8 44 (Not included) = AMPS-1E Ø 4,5 4 Places ,8 30 7,4 3,2 7,2 ables B-M8-4P-2M Ø 5 Ø 9,7 2 m 32 B-M8-4P-5M Ø 5 Ø 9,7 5 m 32 B-M8-4P-5M-90 Ø 9,7 10,7 19 Ø 5 5 m

12 MPS-2 MPS-2 Features Pressure Ranges: Vacuum... 0 to -1 bar Positive Pressure... 0 to 10 bar Sensor Outputs: 2 NPN or PNP Open ollector Transistor Output, 30 VD, 125 ma Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm 2, PSI, bar, kpa) Output Respse Time Less Than 2,0 Millisecds IP65 Rated and E Marked Model Number Output Pressure Range MPS-V2G-P PNP 0 to -1 bar MPS-P2G-P PNP 0 to 10 bar Air and N-orrosive Gases Error Message Output Modes The MPS-2 Series Sensor has two independent NPN or PNP open collector output signals. The Switch Output Mode has a switch point programmed by the user at a specified pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 100% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. Switch Output 0 h off off H -1 bar Window omparator Output 0 off A b off -1 bar off

13 MPS-2 Model Number Index MPS - V 2 G - P Pressure Range V 0 to -1 bar P 0 to 10 bar Port Size G 1/8" BSPP M5 M5 Female* * Din Rail Only ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector M8 4-Pin Din Rail Blank Without R* With * M5 Port Size Only MPS-V2G-P MPS-P2M5-PGR Specificatis Pressure Range Vacuum (V) Positive (P) Units of Measure kpa: 0,1 MPa: 0,001 Display Resoluti Media Pressure Port Proof Pressure Air and N-orrosive Gases G: 1/8" BSPP, M5: M5 Female V: 5 bar, P: 15 bar Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity Electrical necti Power Supply Display 35 to 85% RH : 4-Pin, M8 nector 10,8 to 30 VD, Ripple Vp-p 10% Max., Reverse Voltage Protecti 3-Digit, 7-Segment LED Display Refresh 0,1 to 3,0 sec. (Factory set at 0,1) Output ircuit Switch Output Output Modes Respse Time Repeatability Thermal Error NPN (Sinking) or PNP (Sourcing) Output, Open ollector Transistor 30 VD, 125 ma 2 Output Signals, NPN or PNP, Normally Open or losed, LED Indicator Hysteresis or Window omparator < 2 ms, with Programmable Increments 32, 128, 1024 ms ± 0,2% F.S. 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP65 or IP40, E Rating, EM-EN55011 lass B, EN Insulati Resistance Vibrati Resistance Shock Resistance Material Mass > 100 Mohms at 500 VD 10 to 55 Hz, 1,5 mm, XYZ, 2 hrs. 10 G, XYZ Housing: Polycarbate, Pressure Port: Zinc Die-cast 45 g

14 MPS-2 Wiring Diagram Pin # 1 Brown:24 VD 2 White: NPN / PNP Open ollector Output 3 Blue: 0 VD 4 Black: NPN / PNP Open ollector Output Sensor Male Pin Out Internal ircuit NPN 1 2 PNP NPN Sinking PNP Sourcing autis! Installati The MPS-2 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting base. To achieve IP65 rating, cnect the o-ring and barb as shown to a normal envirment with a 2 mm I. D. tube. 2 1 Ambient Air Inlet Port 2 1 Operatis Dedicate a power supply of 10,8 to 30 VD to the sensor and set the ripple to Vp-p10% or less. Avoid excessive volt age. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating tempera tures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Barb O-Ring oupling INLUDED Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er1 System Error (Internal) tact Factory Er2 Auto Teach Mode Error Restart Functi E1 Over current of Output 1 Load current exceeds E2 Over current of Output 2 maximum 125 ma. FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor

15 MPS-2 Dimensis G 1/8" Male M8, 4-Pin 2 1 M5Fx0,8 44 M3Fx4 Vent Port 25 G1/8M 12, ,7 14 Din Rail M5 Female Grommet 61 3,8 2 1 M5Fx0,8 M3Fx4 Vent Port 25 12,5 5,

16 MPS-2 See page 181 for Symbol Explanati 1 Hold 2 Press 2x 3 Press 1x 2 1 Output Mode Output Set Open Hysteresis or or losed Selecting Window Units of Measure omparator Easy Mode Activati Press 4x 2 1 Output Mode 2 Hysteresis or Window omparator 4 Press 1x 5 Press 3x 6 Press 5x 2 1 Output 1 Setting 2 1 Output 2 Setting 2 1 Automatic Teach Mode Hysteresis Hysteresis & Auto Surveillance Mode Mode Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x 2 1 Display Refresh 2 1 Display Peak Value Settings / Output Bottom Value or Respse Time Their Difference Interval 2 1 Special Display Features 10 Hold Press Lock 2 1 Unlock Hold Press 11 Press 1x Press 1x Peak Value Bottom Value Press for 3 Secds Zero Reset

17 MPS-2 Accessories ables B-M8-4P-2M Ø 9,7 Ø 5 2 m 32 B-M8-4P-5M Ø 9,7 Ø 5 5 m 32 B-M8-4P-5M-90 Ø 9,7 10,7 19 Ø 5 5 m 22 Din Rail MPS-AK

18 MPS-3 MPS-3 Features Pressure Ranges: Vacuum... 0 to -1 bar Positive Pressure... 0 to 10 bar Sensor Outputs: 2 NPN or PNP Open ollector Transistor Output, 30 VD, 125 ma Optial Analog 1 to 5 VD Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm 2, PSI, bar, kpa) Output Respse Time Less Than 2,0 Millisecds IP65 Rated and E Marked Model Number Output Pressure Range MPS-V3G-P PNP 0 to -1 bar MPS-V3G-PG PNP 0 to -1 bar MPS-P3G-P PNP 0 to 10 bar MPS-P3G-PG PNP 0 to 10 bar Air and N-orrosive Gases Error Message Output Modes The MPS-3 Series Sensor has two independent NPN or PNP open collector output signals. An analog output is optial. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 100% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. The optial Analog Output Signal is calibrated to the pressure scale of the sensor. Switch Output 0 h off off H -1 bar Window omparator Output 0 off A b off -1 bar off

19 MPS-3 Model Number Index MPS - V 3 G - P Pressure Range V 0 to -1 bar P 0 to 10 bar Port Size G 1/8" BSPP ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector 4-Pin, M8 G Grommet (2m) MPS-V3G-P MPS-V3G-PG Specificatis Pressure Range Vacuum (V) Positive (P) Units of Measure kpa: 0,1 MPa: 0,001 Display Resoluti Media Pressure Port Proof Pressure Air and N-orrosive Gases G: 1/8" BSPP Female V: 10 bar, P: 15 bar Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity Electrical necti Power Supply Display 35 to 85% RH : 4-Pin, M8 nector, G: Grommet Open Lead 10,8 to 30 VD, Ripple Vp-p 10% Max., Reverse Voltage Protecti 3-Digit, 7-Segment LED Display Refresh 0,1 to 3,0 sec. (Factory set at 0,1) Output ircuit Switch Outputs Output Modes Output Respse Time Repeatability Thermal Error NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30 VD, 125 ma 2 Output Signals, NPN or PNP, Normally Open or losed, LED Indicator Hysteresis or Window omparator < 2 ms with Programmable Increment 32, 128, 1024 ms (XS2H2-32, 256, 512 ms) ± 0,2% F.S. 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP65 or IP 40, E Rating, EM-EN55011 lass B, EN urrent sumpti Vibrati Resistance Shock Resistance Material Mass < 55 ma 10 to 55 Hz, 1,5 mm, XYZ, 2 hrs. 10 G, XYZ Housing: Polycarbate, Pressure Port: Zinc Die-cast 45 g

20 MPS-3 Open ollector Wiring Pin # 1 Brown:24 VD 2 White: NPN / PNP Open ollector Output 3 Blue: 0 VD 4 Black: NPN / PNP Open ollector Output Sensor Male Pin Out autis! Installati The MPS-3 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting bracket. To achieve IP65 rating, cnect the o-ring and barb as shown to a normal envirment with a 2 mm I. D. tube. Pipe Plug Ambient Air Inlet Port Operatis Dedicate a power supply of 10,8 to 30 VD to the sensor and set the ripple to Vp-p10% or less. Avoid excessive volt age. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating tempera tures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Barb O-Ring oupling INLUDED Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er1 System Error (Internal) tact Factory Er2 Auto Teach Mode Error Restart Functi E1 Over current of Output 1 Load current exceeds E2 Over current of Output 2 maximum 125 ma. FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor

21 MPS-3 Dimensis G 1/8" Female 27 4, , Grommet Lead 6,7 4 M8 4-Pin nector 12,2 1/8" BSPP M3 Venting Port MPS-AK1 Mounting Brackets (Included) , Ø 4,5 6 Ø 4, ,

22 MPS-3 See page 181 for Symbol Explanati 1 Hold 2 Press 2x 3 Press 1x Output Mode 1 Output Set Open Hysteresis or or losed Selecting Window Units of Measure omparator Easy Mode Activati Press 4x Output Mode 2 Hysteresis or Window omparator 4 Press 1x 5 Press 3x 6 Output 1 Output 2 Switch Point Switch Point Setting Setting Press 5x Automatic Teach Mode & Auto Surveillance Hysteresis Mode Hysteresis Mode Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Display Peak Value Settings / Output Bottom Value or Respse Time Their Difference Interval Special Display Features 10 Hold Press 1x Hold Press 1x 11 Press 1x Press 1x 12 Press for 3 Secds Zero Reset Lock Unlock Peak Value Bottom Value

23 MPS-3 Accessories ables B-M8-4P-2M Ø 9,7 Ø 5 2 m 32 B-M8-4P-5M Ø 9,7 Ø 5 5 m 32 B-M8-4P-5M-90 Ø 9,7 10,7 19 Ø 5 5 m 22 MPS-AH7 Panel Mounting Bracket 43, ,4 1 2 Knockout 36 (+0.5, -0.2) 36 (+0.5, -0.2)

24 MPS-31 MPS-31 Red Green Display Features Pressure Ranges: Vacuum... 0 to -1 bar Positive Pressure... 0 to 10 bar Sensor Output: 1 NPN or PNP Open ollector Transistor Output, 30 VD, 125 ma Switch Point and High-low Programming 4 Selectable Units of Measure (mmhg, -bar, -kpa, inhg) (kgf/cm 2, PSI, bar, kpa) Output Respse Time Less Than 2,0 Millisecds IP65 Rated and E Marked Model Number Output Pressure Range MPS-V31G-P PNP 0 to -1 bar MPS-V31G-PG PNP 0 to -1 bar MPS-P31G-P PNP 0 to 10 bar MPS-P31G-PG PNP 0 to 10 bar Air and N-orrosive Gases Error Message Output Modes The MPS-31 Series Sensor has e independent NPN or PNP open collector output signal. The Switch Output Mode has a switch point programmed by the user at a specific pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 100% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. Switch Output 0 h off off H -1 bar Window omparator Output 0 off A b off -1 bar off

25 MPS-31 Model Number Index Bold Items Are Standard MPS - V 31 G - P Pressure Range V 0 to -1 bar P 0 to 10 bar R -1 to 5 bar Port Size G 1/8" BSPP ircuit N NPN Sinking Output P PNP Sourcing Output Electrical nector 4-Pin, M8 G Grommet (2 m) MPS-V31G-PG Mounting Bracket MPS-AK1 Included with Sensors. MPS-V31G-P Specificatis Pressure Range Vacuum (V) Positive (P) ompound (R) Units of Measure kpa: 0,1 MPa: 0,001 kpa: 1 Display Resoluti Media Pressure Port Proof Pressure Air and N-orrosive Gases G: 1/8" BSPP Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity Electrical necti Power Supply Display V: 10 bar, P: 15 bar, R: 10 bar 35 to 85% RH : 4-Pin, M8 nector, G: Grommet Open Lead 10,8 to 26,4 VD, Ripple Vp-p 10% Max., Reverse Voltage Protecti 3-Digit, 7-Segment LED Display Refresh 0,1 to 3,0 sec. (Factory set at 0,1) Output ircuit Switch Output Output Modes Output Respse Time Repeatability Thermal Error NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30 VD, 125 ma Output Signal, NPN or PNP, Normally Open or losed, LED Indicator Hysteresis or Window omparator < 2 ms, 32, 256, 512 ms Programmable (Factory set 2 ms) ± 0,2% F.S. 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP65 or IP40, E Rating, EM-EN55011 lass B, EN urrent sumpti Vibrati Resistance Shock Resistance Material Mass < 70 ma 10 to 55 Hz, 1,5 mm, XYZ, 2 hrs. 10 G, XYZ Housing: Polycarbate, Pressure Port: Zinc Die-cast 48 g

26 MPS-31 Open ollector Wiring Pin # 1 Brown: 24 VD 2 Black: NPN/PNP Output 1 3 Blue: 0 VD Sensor Male Pin Out Internal ircuit D1 (Brown) +V D1 (Brown) +V Main ircuit Tr1 ZD1 (Black) Out 1 LOAD Max. 125mA (Blue) OV + D V to 30V Main ircuit Tr1 ZD1 (Black) Out 1 (N.O.) LOAD Max. 125mA (Blue) OV + D V to 30V NPN PNP autis! Installati The MPS-31 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install as shown using the metal mounting bracket. To achieve IP65 rating, cnect the o-ring and barb to a normal envirment with a 2 mm I. D. tube. Pipe Plug Ambient Air Inlet Port Operatis Dedicate a power supply of 10,8 to 30 VD to the sensor and set the ripple to Vp-p10% or less. Avoid excessive volt age. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating tempera tures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Error Messages Barb O-Ring oupling INLUDED Display Descripti Solutis Err Zero Reset Error Reset Zero Below 3% of F.S. Er1 System Error (Internal) tact Factory E1 Over current of Output 1 Load current exceeds FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor

27 MPS-31 Dimensis G 1/8" Female 27 4, , Grommet Lead 6,7 4 M8 4-Pin nector 12,2 1/8" BSPP M3 Venting Port MPS-AK1 Mounting Brackets (Included) , Ø 4,5 6 Ø 4, ,

28 MPS-31 See page 181 for Symbol Explanati 1 Press for 3 Secds Begin Programming Operating Output Mode Output Normally Open or losed Select Units of Measure Or Press 1x to Proceed Or Press 1x to Proceed Or Press 1x to Proceed Wait 3 Secds Wait 3 Secds Wait 3 Secds Display Refresh Output Respse Selecti Display olor hoices Red and / or Green, Energy Save Or Press 1x to Proceed Or Press 1x to Proceed Or Press 1x to Return Wait 3 Secds Wait 3 Secds Wait 3 Secds Output On Off Red Green Green Red Green Red Red Green 2 Press 1 x 3 Press 1 x Switch Output Setting and Low Setting Hysteresis Setting and High Setting 4 Hold Press 1 x Hold Press 1 x Will Display for 1 Secd Hysteresis Mode Will Display for 1 Secd Hysteresis Mode Lock Unlock Window omparator Mode Window omparator Mode 5 Zero Reset Low High Wait 5 Secds Wait 5 Secds Press for3 Sec

29 MPS-31 Accessories ables B-M8-4P-2M Ø 9,7 Ø 5 2 m 32 B-M8-4P-5M Ø 9,7 Ø 5 5 m 32 B-M8-4P-5M-90 Ø 9,7 10,7 19 Ø 5 5 m 22 MPS-AH7 Panel Mounting Bracket 43, ,4 Knockout 36 (+0,5, -0,2) 36 (+0,5, -0,2)

30 MPS-6 Model Number Output Pressure Range MPS-V6G-P PNP 0 to -1 bar MPS-V6G-AG Analog 0 to -1 bar MPS-V6G-AGE Analog 0 to -1 bar MPS-P6G-P PNP 0 to 10 bar MPS-P6G-AG Analog 0 to 10 bar MPS-P6G-AGE Analog 0 to 10 bar Features MPS-6 Pressure Ranges: Vacuum... 0 to -1 bar Positive Pressure... 0 to 10 bar Sensor Outputs: 1 Open and 1 losed NPN or PNP Open ollector Transistor Output 30 VD, 125 ma 1 Analog Output 1 to 5 VD Switch Point 2/3 Trimmer Fixed Hysteresis 2% Output Respse Time Less Than 1 Millisecd Analog Output Type ompatible with MPS-7 Display IP40 Rated and E Marked Air and N-orrosive Gases Output Modes The MPS-6 Series Sensor is compact and lightweight with NPN or PNP open cnector switch output or analog output capabilities. The sensor can be used as a stand ale unit or in combinati with the MPS-7 series display. The MPS-6 Switch Output unit provides e open and closed output for the same switch point. The MPS-6 Analog Output unit provides analog output 1 to 5 VD. Analog output is required for use with the MPS-7 display. Switch Output S 0 Fixed 2% off off -1 bar Analog Output Output (Volts) Max. Rating Pressure

31 MPS-6 Model Number Index MPS - V 6 G - P Pressure Range V 0 to -1 bar P 0 to 10 bar Port Size G 1/8" BSPP & M5 Female T 6 mm Tube Stud Output ircuit N NPN Output P PNP Output A Analog (1 to 5 VD)* Electrical nector 4-Pin, M8 G Grommet (2 m) GE 2 m Grommet lip n.* * With Grommet GE Only *Use with MPS-7 Series Display, with Analog Only MPS-P6G-P MPS-P6G-AG MPS-V6T-PG MPS-P6G-AGE Specificatis Media Air and N-orrosives Gases Pressure Port G: 1/8" BSPP Male, T: 6 mm Tube Stud Proof Pressure V: 5 bar, P: 15 bar Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity 35 to 85% RH Electrical necti : 4-Pin, M8 nector G: Grommet Lead GE: lip Type for use with MPS-7 Display Power Supply 10,8 to 30 VD, Ripple Vp-p 10% max., Reverse Voltage Protecti Switch Output 1 Output Signal Open and losed, NPN or PNP, 30 VD, 125 ma Linear Output Analog Output 1 to 5 VD Switch Point Setting 2/3 Turn Trimmer Hysteresis Setting < 2% of F.S. Output Respse Time <1 ms Repeatability <0,2% F.S. Thermal Error 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP40, E Rating EN55011 lass B, EN urrent sumpti < 20 ma Spike Protecti 400 VP, 1 µs, Surge Protecti Dielectric Strength 1000 VA, 1 min. Insulati Resistance > 100 Mohm at 500 VD Vibrati Resistance 10 to 55 Hz, 0,75 mm Amplitude, XYZ, 2 hrs. Shock Resistance 100 G, XYZ Material Housing: Polycarbate, Pressure Port: Zinc Die-cast Mass T Port: 7 g, N, R, G Port: 25 g

32 MPS-6 Open ollector Wiring Pin # 1 Brown: 24 VD 2 White: NPN / PNP Open ollector Output N.. 3 Blue: 0 VD 4 Black: NPN / PNP Open ollector Output N. O. Analog Wiring Pin # 1 Brown: 24 VD 2 White: LED In 5 VD 3 Blue: 0 VD 4 Black: Analog 1 to 5 VD Sensor Male Pin Out Internal ircuit Main ircuit Tr1 Tr2 D1 (Brown) +V ZD1 (Black) Out 1 (N.O.) LOAD Max. 125mA ZD2 (White) Out 2 (N..) LOAD Max. 125mA (Blue) OV NPN Open ollector + D 10.8V to 30V (Brown) +V D1 (Brown) +V Main ircuit LED (White) Input for LED lighting (5VD) (Black) Analog 1 5V Output (Blue) OV + D V to 30V Main ircuit Tr1 Tr2 ZD1 (Black) Out 1 (N.O.) LOAD Max. 125mA ZD2 (White) Out 2 (N..) LOAD Max. 125mA (Blue) OV + D 10.8V to 30V Analog PNP Open ollector autis! Installati The MPS-6 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting bracket. Operatis Dedicate a power supply of 10,8 to 30 VD to the sensor and set the ripple to Vp-p10% or less. Avoid excessive volt age. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating tempera tures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Trimmer Adjustment Rotate the potentiometer trimmer to increase or decrease pressure switch point output. Excessive force or exceeding the limits of the trimmers may cause damage. Switch Point Trimmer

33 MPS-6 Dimensis G 1/8" Male, M5 Female, Grommet 16 1/8" BSPP 26,3 Switch Point Trimmer Output LED Output LED 20 2 m or T6 M5 6 Tube Stud, Grommet 34, ,8 2 m 6 mm Tube 10 G 1/8" Male, M5 Female, M8, 4-Pin 16 1/8" BSPP 26,3 Switch Point Trimmer Output LED Output LED T6 Tube Stud, M8, 4-Pin 20 M5 6 34,1 15 or 16 19,8 Switch Point Trimmer Output LED 20 6 mm Tube 15 G or T6 Grommet lip nector 16 1/8" BSPP 26,3 AMP 5-Pin nector M5 6 2 m

34 MPS-6 Accessories ables B-M8-4P-2M Ø 9,7 Ø 5 2 m 32 B-M8-4P-5M Ø 9,7 Ø 5 5 m 32 B-M8-4P-5M-90 Ø 9,7 Ø 9, ,7 Ø 5 5 m

35 MPS

36 MPS-7 MPS-7 Features One Display with Output Programming apability for MPS-5, 6, or 8 Analog Sensors Displays Pressure and verts Analog Signal from Remote Sensor to NPN or PNP Open ollector Transistor Output, 30 VD, 125 ma ompatible with 1 to 4 Remote Sensors MPS-71 Respse Time Less Than 2,0 Millisecds MPS-74 Respse Time Less Than 5 Millisecds IP40 Rated and E Marked Model Number MPS-71E-N MPS-71E-P MPS-71E-NG MPS-71E-PG MPS-74E-NG MPS-74E-PG Output NPN PNP NPN PNP NPN PNP MPS-71E-PG trol with Remote MPS-P6G-AGE Shown Output Modes Switch Output The MPS-7 is a central display and ctrol for remote MPS-5, 6, 8 analog sensors. Each remote sensor supplies an analog signal to a specific channel the MPS-7 which is cverted to an open cnector output NPN / PNP. The Switch Output Mode has a switch point programmed by the user at a specified pressure. The Hysteresis Range (h) adjustment ctrols the output signal 0 to 100% below the Switch Point (H). The Window omparator Mode provides two Switchpoint Settings (A) and (b) that ctrol the output signals (NPN / PNP) between two pressures. This is referred to as the High / Low setting. 0 h off H -1 bar Window omparator Output 0 A b off -1 bar off off off

37 MPS-7 Model Number Index MPS E - N Number of Remote Sensors 1 1 Sensor 4 4 Sensors ircuit N NPN Output Sinking P PNP Output Sourcing Electrical nector * 4-Pin, M8 G Grommet (2 m) * Available MPS-71 ly. MPS-71E-PG Mounting Bracket Included with Sensors. MPS-74E-NG Specificatis Remote Pressure Range Vacuum (V) Positive (P) Units of Measure kpa: 0,1 MPa: 0,001 Display Resoluti Proof Pressure Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity Electrical necti Power Supply Display Display Refresh ircuit 74-1 Switch Output 71-2 Switch Outputs Linear Output Mode (71 Series) Respse Time Repeatability Thermal Error General Protecti urrent sumpti Vibrati Resistance Shock Resistance Material Mass See Remote Sensor Specificatis 35 to 85% RH G: Grommet Open Lead, : M8 nector 10,8 to 30 VD, Ripple (P-P) 10% Max., Reverse Voltage Protecti MPS-71: 3-Digit, 7-Segment LED, MPS-74: 4-Digit, 7-Segment LED MPS-71: 0,1 to 3,0 sec. (Factory set at 0,1), MPS-74: 0,2 Fixed NPN (Sinking), PNP (Sourcing) Open ollector Transistor, 30 VD, 125 ma Output Signals, NPN or PNP, LED Indicator Optial Output - Analog 1-5VD, ± 0,2% Linear Accuracy, 0,5% F.S MPS-71 <2 ms, MPS-74 <5 ms ± 0,2% F.S. 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) IP40 MPS-71 <45 ma, MPS-74 <75 ma 10 to 55 Hz, 1,5 mm, XYZ, 2 hrs. 10 G, XYZ Body: Polycarbate MPS-71:.25 g, MPS-74: 28 g

38 MPS-7 MPS-71 Open ollector Wiring Pin # MPS-74 Open ollector Wiring Grommet Lead Only 1 Brown: 24 VD Brown: 24 VD 2 Black: NPN / PNP Open ollector Black: NPN / PNP Open ollector 3 Blue: 0 VD Blue: 0 VD 4 White: NPN / PNP Open ollector White: NPN / PNP Open ollector Pink: NPN / PNP Open ollector Orange: NPN / PNP Open ollector Sensor Male Pin Out Internal ircuit (Brown) +V (Black) Out 1 Main ircuit (White) Out 2 (Pink) Out 3 (74E) (Orange) Out 4 (74E) (Blue) O V MPS-71 & MPS-74 NPN / PNP Open ollector autis! Installati The MPS-7 entral Display is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 10,8 to 30 VD to the MPS-7 Se ries and set the ripple to Vp-p10% or less. Avoid excessive voltage. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Avoid short-circuiting the MPS-7 Series. nect the brown lead to V+ and blue lead to 0 V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using Panel Mount Bracket or Back Mount Brackets. Error Messages Display Descripti Solutis Err Zero Reset Error Reset Zero PErr Peak Value Error heck Vacuum Source Er1 System Error (Internal) tact Factory E1 Over current of Output 1 E2 Over current of Output 2 Load current exceeds E3 E4 Over current of Output 3 (MPS-74) maximum 125 ma. Over current of Output 4 (MPS-74) FFF Applied pressure exceeds Apply pressures with FF pressure range the rating of the sensor

39 MPS-7 Dimensis MPS M , AMP EI 5-Pin nector MPS-AK1 14 Mounting Bracket (Included) ,5 Ø 4, Ø 4, ,5 13 MPS ,5 AMP EI 5-Pin nector H-2 H-1 H-2 H H-4 H-3 H-4 H Reset IN M3 2- M3 MPS-AK Mounting Bracket (Included) 7 Ø 4,5 30 Ø 3,5 Ø 4,5 5, Ø 3,5 5, ,

40 MPS-7 See page 181 for Symbol Explanati 1 Hold Press 1x Output Set Open or losed Easy Mode Activati 2 Press 2x 3 Press 4x Output Mode 1 Hysteresis or Window omparator Output Mode 2 Hysteresis or Window omparator 4 Press 1x 5 Press 3x 6 Press 5x Output 1 Switch Point Setting Output 2 Switch Point Setting Hysteresis Mode Hysteresis Mode Automatic Teach Mode & Auto Surveillance Vacuum ycle Window omparator Mode Low Window omparator Mode Low Release ycle High High 7 Press 6x 8 Press 7x 9 Press 8x Display Refresh Settings / Output Respse Time Display Peak Value Bottom Value or Their Difference Interval Special Display Features 10 Press 9x 11 Hold Hold 12 Press 1x Press 1x 13 Press Select Press 1x Press 1x Units of Measure 3 Sec Select Pressure Lock Unlock Peak Value Bottom Value Zero Reset Vacuum Low Pressure Positive Pressure ompound Pressure

41 MPS-7 1 Hold Press 1x Output Selecti Normally Open / Normally losed 2 Press 1x Select Output Mode Hysteresis or Window omparator Output Setting Peak Surveillance (Repeat Procedure for Each hannel) Hysteresis Mode Window omparator Mode 3 Press 2x 4 Select Remote Pressure Select Unit of Measure Press 3x Save Energy Mode Digital IN Mode Vacuum Low Pressure Standard Pressure ompound Pressure 5 Press and Hold 3 Secds 6 Scan Mode Hold Press 1x Hold Press 1x Lock Unlock 3 Secd Intervals

42 MPS-7 Accessories ables (Applicable to MPS-71E Display Units Only) B-M8-4P-2M Ø 9,7 Ø 5 2 m 32 B-M8-4P-5M Ø 9,7 Ø 5 5 m 32 B-M8-4P-5M-90 Ø 9,7 10,7 19 Ø 5 5 m

43 MPS-7 Accessories MPS-AH4 Panel Mounting Bracket for MPS-71 43, ,4 1 2 Knockout 36 (+0.5, -0.2) 36 (+0.5, -0.2) MPS-AH5 Panel Mounting Bracket for MPS-74 53, Knockout 46 (+0,5, -0,2) 46 (+0,5, -0,2)

44 MPS-8 Features MPS-8 Pressure Ranges: Vacuum... 0 to -1 bar Sensor Outputs: 1 NPN / PNP Open ollector Transistor Output 30 VD, 125 ma 1 Analog Output 1 to 5 VD Switch Point 2/3 Trimmer Adjustment Fixed Hysteresis 2% 10 mm Wide ompatible with MPS-7 Display IP40 and E Marked Air and N-orrosive Gases Model Number Output Pressure Range MPS-V8A-PG PNP 0 to -1 bar MPS-V8U-AG Analog 0 to -1 bar MPS-V8U-AGE Analog 0 to -1 bar Output Mode The MPS-8 Sensor is 10 mm wide with an NPN / PNP open collector switch output or an analog output. The MPS-8 can be used in combinati with the MPS-7 series display or as a stand ale unit. Analog output is required for use with the MPS-7 display. Switch Output S 0 Fixed 2% off off -1 bar Analog Output Output (Volts) Max. Rating Pressure

45 MPS-8 Model Number Index MPS - V 8 A - A G Pressure Range V 0 to -1 bar A B U T Port Size M5 Through Female M5 Through Female (With Mtg.) M5 Bottom Female M5 Bottom Swivel Male 4 mm Tube Stud Output ircuit A Analog (1-5VD) N NPN Sinking Output P PNP Sourcing Output nector / able G Grommet (2 m) GE 2 m Grommet lip n.* * Use with MPS-7 Series Display, with Analog Only Specificatis Media Air and N-orrosive Gases Pressure Port M5 Female, M5 Male Swivel, 4 mm Tube Stud Proof Pressure V: 5 bar Operating Temperature 0 to 50 Storage Temperature -10 to 60 Humidity 35 to 85% RH Electrical necti G: Grommet Open Lead; GE: lip Type for use with MPS-7 Series Power Supply 10,8 to 30 VD, Ripple Vp-p 10% Max., Reverse Voltage Protecti Switch Output 1 Output, Normally Open, NPN or PNP Open ollector Transistor, 30 VD, 125 ma Linear Output Analog Output 1 to 5 VD Switch Point Setting 2/3 Trimmer Hysteresis < 2% of F.S. Fixed Respse Time <1 ms Repeatability < 0,2% F.S. Thermal Error 1% over ±25 (77 ) Temperature hange (Range 0 to 50 ) General Protecti IP40, EM rating : EN55011 lass B, EN urrent sumpti < 20 ma Spike Protecti Vp-p 400 v, 0,5 ms Surge Protecti Dielectric Strength 1000 VA, 1 min. Insulati Resistance > 100 Mohms at 500 VD Vibrati Resistance 10 to 55 Hz, 1,5 mm amplitude, XYZ, 2 hrs. Shock Resistance 100 G, XYZ Material Body: Polycarbate; Pressure Port: Anodized Aluminum Mass 4 g

46 MPS-8 Open ollector Wiring Grommet Lead Only Brown: 24 VD Blue: 0 VD Black: NPN / PNP Open ollector Analog Wiring Grommet Lead Only Brown: 24 VD Blue: 0 VD Black: Analog 1 to 5 VD Internal ircuit D1 (Brown) +V D1 (Brown) +V Main ircuit Tr1 ZD1 (Black) Out 1 LOAD Max. 125 ma (Blue) OV + D - 10,8 V to 30 V Main ircuit Tr1 ZD1 (Black) Out 1 (N.O.) LOAD Max. 125 ma (Blue) O V + D -10,8 V to 30 V NPN Open ollector PNP Open ollector (Brown) +V Main ircuit (Black) Analog 1 to 5 V Output + D - 10,8 V to 30 V (Blue) O V Analog autis! Installati The MPS-8 Pressure Sensor is designed to mitor pressure and is not a safety measure to prevent accidents. The compatibility of the sensor is the respsibility of the designer of the system and specificatis. Operating Envirment Parker / vum Sensors have not been investigated for ex plosi-proof cstructi in hazardous envirments. Do not use with flammable gases, liquids, or in hazardous envirments. Avoid installing the sensor in locatis where excessive voltage surges could damage or affect the performance of the sensor. Operatis Dedicate a power supply of 10.8 to 30VD to the sensor and set the ripple to Vp-p10% or less. Avoid excessive volt age. Avoid voltage surges. A small amount of internal voltage drop is possible. Ensure the power supply minus any internal voltage drop exceeds the operating load. Verify the operating media is compatible with the specified sensor. heck the chemical make-up, operating tempera tures, and maximum pressure ranges of the system before installing. Installati of air dryer system is recommended to remove moisture. Never insert an object into the pressure port other than an appropriate fluid cnector. Avoid short-circuiting the sensor. nect the brown lead to V+ and blue lead to 0V. Do not cnect the output lead wires (black / white) to the power supply. Outputs not being used should be trimmed and insulated. Install using the metal mounting base