Pumps. Bulk Oil Systems. Bulk Oil Systems

Transcription

1 Bulk Oil Systems Bulk Oil Systems 3:1 and 5:1 Ratio Packages Lincoln pump 3:1 and 5:1 ratio packages include regulator, gauge, 815 coupler and nipple. Control valve, inline meter or handheld metering control valve must be ordered separately (except model 4283). Model :1 with 50' Reel & Meter Deluxe assembly including :1 ratio pump with bung bushing, universal suction tube with foot valve to fit any size container up to 275 gallons. Includes 1/2" x 50' oil hose reel with 2' connecting hose. 967 electronic meter totalizes in gallons with quart, gallon or pint readout. PUMPS NOTE: Pipe, fittings and hardware for installation of overhead reel assembly supplied by others. Reel Meter Packages Lincoln puts all the components you specify in one easy-to-order package. RPM Packages Model Kit/Ratio Reel/30' Electronic Meter Air Regulator Air Gauge RPM /3: quarts RPM /3: universal RPM /5: universal NOTE: Always consult fluid/solution manufacturer specifications AND local fire code(s) before installing any pump into service. Most modern automotive fluid/solutions include some type of additive package which may not be compatible with the typical applications listed below. Some fluids or solutions are considered flammable and/or combustible in which case the dispensing pump should be properly grounded. (Order air coupler and air nipple separately) 4493 System for mounting pump and reel on tank Model 4493 Value Series, Reel and Meter Package Configured for above-ground tank installations. For use with natural and synthetic oils, automatic transmission fluid, gear oil, antifreeze or hydraulic oil throughout the shop. Fast, reliable dispensing with the 4491/six GPM free delivery pump. Easy handling, dependable service with the Series hose reel s heavy-gauge steel base, brass bushings and extra-wide hose guide. Accurate and easy dispensing with the 952 electronic oval gear meter with flexible extension. Package includes 4491/3.5:1 pump, reel with 30' x 1 2" hose, ball stop, 952 electronic meter (measures in quarts), air line regulator and gauge, air coupler and nipple, 2' fluid connecting hose from pump to reel and adapter union. 39

2 Air-Operated Diaphragm 1 /4" - 2" Air-Operated s Basic Design Features Diaphragm pumps are driven by compressed air. The directional air distribution valve and pilot valve the air end are located in the center section of the pump. Liquid moves through two manifolds and outer chambers of the pump the wet end. Generally, check valves are located at the top and bottom of each outer chamber or on a common manifold. The two outer chambers are connected Right chamber discharge Left chamber suction Left chamber discharge Right chamber suction by suction and discharge manifolds. Lincoln s double diaphragm self-priming design offers many advantages over other pumps. abrasive and sheer-sensitive materials. Low interval velocities move abrasives easily with no damage. Gentle pumping action does not sheer fragile materials. s viscous materials. Even heavy or solids-laden materials can be pumped. Environmentally friendly. No motors, seals or packing to leak. Self-priming. Able to dry prime under most suction lift or flooded suction conditions. Variable flow. Regulate the inlet air supply to adjust flow. Runs dry without damage. Deadheads against closed discharge. Excessive back pressure stops operation without damage until discharge opens. Eliminates bypass systems or relief valves. Explosion-proof. Eliminates sparking concerns of other electrical or rotating pumps WARNING The pump exhaust should be piped to an area for safe disposal of product being pumped in the event of a diaphragm failure. 1:1 Air-Operated Diaphragm Line Wetted Max. Free Air Max. Rec. Max. Model or Soft Inlet/Outlet Delivery Inlet Inlet Air Susp. Number Description Body Parts NPT gpm NPT(F) Pressure Solids Application ¹ ₄" Polyprop PTFE ¹ ₄" / ¹ ₄" 4 ¹ ₄" 100 psi ¹ ₃₂" New oil, AF, windshield washer ¹ ₂" Aluminum Buna-N ¹ ₂" / ¹ ₂" 15 ¹ ₄" 100 psi ¹ ₈" New/used oil, AF ¹ ₂" Aluminum Teflon ¹ ₂" / ¹ ₂" 15 ¹ ₄" 100 psi ¹ ₈" New oil, AF ¹ ₂" Aluminum Hytrel ¹ ₂" / ¹ ₂" 15 ¹ ₄" 100 psi ¹ ₈" New oil ¹ ₂" Polyprop Santoprene ¹ ₂" / ¹ ₂" * 14 ¹ ₄" 100 psi ¹ ₈" High abrasion materials ¹ ₂" Polyprop Teflon ¹ ₂" / ¹ ₂" * 14 ¹ ₄" 100 psi ¹ ₈" New oil, AF ¹ ₂" Polyprop Buna-N ¹ ₂" / ¹ ₂" * 14 ¹ ₄" 100 psi ¹ ₈" New oil, AF " Aluminum Hytrel 1"/ 1" 45 ¹ ₂" 125 psi ¹ ₄" New oil " Aluminum Teflon 1"/ 1" 45 ¹ ₂" 125 psi ¹ ₄" New oil, AF " Aluminum Buna-N 1"/ 1" 45 ¹ ₂" 125 psi ¹ ₄" New/used oil, AF ¹ ₂" Aluminum Buna-N 1¹ ₂" / 1¹ ₂" 106 ³ ₄" 125 psi ¹ ₄" New/used oil, AF " Aluminum Buna-N 2"/ 2" 150 ³ ₄" 125 psi ¹ ₄" New/used oil, AF Dual Inlet ¹ ₂" Aluminum Buna-N ¹ ₂" / ¹ ₂" 15 ¹ ₄" 125 psi ¹ ₈" AF/Water ¹ ₂" Polyprop Buna-N ¹ ₂" / ¹ ₂" 14 ¹ ₄" 100 psi ¹ ₈" AF/Water " Polyprop Buna-N 1"ANSI** 45 ¹ ₂" 100 psi ¹ ₄" AF/Water " Aluminum Buna-N 1"/ 1" 42 ¹ ₂" 125 psi ¹ ₄" AF/Water * Can be converted to dual 1/2" outlet. ** requires Adapter and Seal Kit for Pipe Thread installations 40

3 Air-Operated Diaphragm Accessories U.L. Listed " UL Aluminum Buna-N 1"/ 1" 45 ¹ ₂" 50 psi * ¹ ₄" Used oil, diesel, kerosene " UL Aluminum Teflon 1"/ 1" 45 ¹ ₂" 50 psi * ¹ ₄" Unleaded gas, diesel, kerosene, used oil * 50 psi flammable liquids, 125 psi others Wall Mount Brackets Model Wall Mount Bracket Wall mount bracket for 1 /4" to 1 /2" air-operated diaphragm pumps. Model Wall Mount Bracket Wall mount bracket for 1 /2" to 2" air-operated diaphragm pumps. Other Accessories Model Drum Adapter Kit For use with 1 /2" polypropylene AOD pumps. Includes 2" NPT(f) bung bushing, 1" x 36" suction tube and adapter. Model " ANSI Flange To 1" NPT Adapter Adapts 1" ANSI flange of polypropylene dual inlet pump to 1" NPT(f). PVC for low pressure installations. Three required to convert all pump inlets/outlets. Model ANSI Bolt Kit with Seal Attaches adapter to pump. One bolt kit required for each adapter. Three required to convert all pump inlets/outlets. Transfer Accessories Suction Kits Model Suction Kit For transfer of product from drums, bulk tanks or reservoirs. Includes bung bushing suction tube, hose and coupling assembly. NOTE: 2" x 1" bell reducer required for use with Model 1914, not included. Model Same as except for use with 1/4" AOD pump. Used-Fluid Overfill Warning Valves Float rises with used fluid to activate whistle warning at prescribed level. Model Single Wall For single wall tanks & drums in used fluid systems and above ground tanks. Model Double Wall Same as except for double walled tanks and above ground tanks. 4-Way Valve Model Four port, two position valve used in waste fluid systems. Enables one pump to pump into and out of drum or tank. Thermal Pressure Relief Valve Model Protect lube system components from high-pressure spikes caused by temperature change in a closed fluid network. Model Application Pre-Set Relief Pressure Port Size psi (10.2 bar) Diaphragm s, 1000 psi (68 bar) :1, 5:1 500 psi (34 bar) 1/2" NPT psi (104 bar) PUMPS 41

4 Transfer / 1:1 1:1 Piston Transfer s Model Descrip. Body Wetted or Soft Parts Inlet/Outlet NPT Max. Free Delivery GPM Air Inlet NPT(f) Max. Rec. Inlet Air Pressure Max. Susp. Solids Dia. Typical Automotive Use stub alum/steel/ plastic Buna N 1"/ 3 /4" 14 gpm 1 /4" 150 psi NA Universal/new oil transfer gal. drum alum/steel Buna N 3/4" 111/2" A.N. 20 gpm 1/8" 150 psi NA 55-gal. drum/new oil transfer Model Universal Stub pump design provides the versatility to transfer and dispense controlled amounts of lubricant using an oil spigot, control valve or meter. Adaptable for 16- or 55-gal. containers as well as bulk tank or standpipe installations. Delivers 12.5 cu. in. per cycle. Includes air motor 84831, pump tube 84828, suction tube, bung bushing, air coupler and air nipple. Model Transfer pump quickly transfers fluids directly from 55-gallon drums. 2" bung bushing adjusts to varied drum lengths. Designed to stall against lubricant pressure. Use built-in air control valve to adjust fluid output flow. Model Teflon Kit For use with 82230, to allow compatibility with additional products. Model 1326 Diaphragm Action Neoprene seals resist wear from abrasive fluids. Double-acting diaphragm delivers one full gallon per eight strokes. 8' hose with discharge nozzle. Transfer Model Drum Size Bung Bushing Output to 55-gal. w/2" bung opening 2" NPT(m) 1 pint per stroke Model 1335 This close tolerance pump utilizes brass rings for extreme durability and expanded fluid compatibility. Telescoping pick-up tube for 16- through 55-gallon drums with standard 2 bung openings. Bung opening tool built into pump head to open sealed refinery container. Provides 8.5 fl. oz. per full stroke. For use with non-corrosive fluids such as motor oil, transmission fluid, gear oil, engine coolant, silicone oils, and more. Model 1340 Lever Action Barrel Extended pump body improves top-of-barrel clearance while providing excellent flow per stroke. s non-corrosive automotive, agricultural and industrial fluids * Extended pump body for improved top-of-barrel clearance and excellent flow (14.0 fl oz. minimum per stroke) Removable non-drip spout allows for threaded hose connection Telescoping pick-up tube for 16- to 55-gallon drums Three-tier threaded bung fits standard 2" and 1.5" drums and plastic drums utilizing 56 x 4 mm buttress threads * Not suitable for gasoline

5 Transfer / 1:1 Value Series Features and Benefits Designed for Value Proven horizontal, valved-piston motor design for simplicity and reliability Provides quick dispense, fill or transfer with high-volume output Built-in muffler for quiet operation Cost-effective solution for oil distributors who need to supply pumps for customers who purchase bulk oil in tanks or drums Available as stub pump, 16-/55-gallon pump or 250- to 275-gallon tank pump Motor s single-stroke action delivers cost effective, high performance and high flow Provides quick dispense and fill of ATF, oil, gear lube and other fluid lubricants with the speed of many higher-priced pumps Ideal for use with one or two overhead reels in applications such as medium-to-light vehicle service facilities, car dealerships, small contractors, farmers and agriculture equipment dealers PUMPS Specifications Ratio Output/ Stroke Delivery Output Pneumatic Inlet Pressure Max. Min. Oper. Temp. Range Weight (Empty) Pneum. Port Inlet Material Port Outlet Rec d. Fluids :1 5.6 in 3 91 cm 3 6 GPM 120 psig 8.3 bar 20 psig 1.4 bar 30 F F -1 C - 49 C 14 lbs NPTF 1 2 NPTF Motor oils, transmission fluid, petroleum-based fluids 4480 Specifications Models Model No. Application Mounting Down Tube Length gallon 2" NPT male bung adapter 36.5" gallon oval tank 2" NPT male bung adapter 47.0" 4492 Stub 1.5" NPT male N/A Model 4475 Series The Model 4475 pump is a reciprocating-piston, low-pressure single action pump. Air powers the pump s piston on the dispensing, or working, stroke. An internal spring returns the piston and resets it for the working stroke. It pumps continuously when the dispensing (fluid outlet) valve is open and psig air is supplied to the pump. Material Tube Effective Inlet Air Output/ Free Model Description Outlet Operation Length Attachment Ratio Pressure Stroke Delivery *4475 Bare ¹ ₂" NPTF Pneum. pressure 2" Bung, adj. Approx. Max: 120 psi Spigot extension delivery stroke, 34" for 55- & 16-gal. 0.7:1 to 0.8:1 (8.3 bar) 2.9 in 3 Up to *4480 Spigot with on/off spring return (86 cm) drums, bench & depending Min: 20 psig (48 cm 3 ) 4 gpm valve stroke portable tank on inlet air (1.4 bar) (15 lpm) pressure * Bung bushing , ,

6 Lube Dispensing Stations Model 4030 This inline design, 6 product console is compact the perfect dispensing station for between the bays installations which allows servicing of two vehicles from one location. Heavy-duty welded lower cabinet construction is finished in safety red. Metering control valves rest on top of the console in the meter cradle, eliminating the need for ball stops on oil products. Air or water hoses rest in small O.D. hose brackets which require a ball stop. Hoses gravity feed through the floor into the fast oil change basement or pit area. The inline console includes composite hose guide plates and a composite meter cradle which: Are constructed of self-lubricating composite material hoses glide over easily Replaces rollers no rollers are needed Does not require maintenance Two small OD hose brackets are included with each 4030 console 4030 Specifications Dimensions Capacity 42"L x 12 5 /8"W x 36"H 6 products Hoses, meters, control valves and ball stops (required for non-metered products only) are available separately Oil Bar Assembly Model Includes single delivery spigot for dispensing motor oil, ATF and other fluids. Base unit may be expanded two additional positions by adding spigot kits, meters or other accessories. Removable tray for disposal of spillage; 14 gauge steel. Model Oil Bar Spigot Kit To add products to base model 84959, order one spigot kit for each additional product to be dispensed. Includes hardware and bulkhead fitting kit. Oil Spigots Model Spring-loaded oil spigot is used with oil pumps to dispense fluids into oil crankcase fill cans. 1 /2" NPT(m)