Logging of RF Power Measurements
|
|
- Amber Norman
- 2 years ago
- Views:
Transcription
1 Logging of RF Power Measurements By Orwill Hawkins Logging of measurement data is critical for effective trend, drift and Exploring the use of RF event analysis of various processes. For RF power measurements, logging power data logging with is used in a number of applications including during environmental test, a USB power sensor. characterizing transmit power versus battery drain or temperature, analyzing RF interference, and monitoring signals in the field. These applications have different requirements for the speed at which the data needs to be recorded. For instance, measuring the RF power of a transceiver module during thermal cycling may only require measurements every few seconds or more; but when trying to catch an intermittent spurious signal at a particular frequency, higher speed logging on the order of milliseconds or less will be required. Figure 1 shows an example text file for a logging process recording data at about every 250 ms. We will explore the use of RF power data logging with a USB power sensor. Together with a computer and data logging software, this solution provides a cost-effective method for addressing these wide-ranging applications. In addition, we will review ways to optimize the logging measurements to conserve memory, making data reduction and analysis easier. Finding Root Causes When performing environmental stress testing such as burn-in or thermal cycling, it is important to know how far into the test a failure occurred and whether it was gradual or immediate. This information will be critical in determining the root cause of the failure of a RF transmitter module or a RF amplifier. Additionally, logging RF power data through thermal cycles provides not only information about failures and failure rates but can also be useful in characterizing the behavior of the RF device and how it might change over time and number of cycles. As this type of testing may Figure 1 Text file with the table of logging results. 22 High Frequency Electronics
2 Figure 2 Slow speed logging of an RF amplitude ramp using a LadyBug USB power sensor. In addition to the graphical display the data can be written to a file for recording data points over a long time period. take place over days or even weeks using multiple sensors, the amount of data captured could be significant. How often data points are recorded depends on the anticipated failure rate and how much accuracy with respect to time is needed. Figure 2 shows an RF power ramp over a period of a little less than 30 seconds. The wide dynamic range of the LadyBug sensor allows measurements from - 60 to + 20 dbm. Logged data can be written to a file or shown in a graphical dis- Figure 3 High speed logger can be used to track signal amplitude changes like this pulsed signal (20 ms period and 5 ms width). The LadyBug High Speed Logger application software enables fast capture of data that can be exported to tools like Excel TM or MATLAB TM for analysis and visualization. 24 High Frequency Electronics
3 Figure 4 Logging data with a LadyBug USB Power Sensor provides an inexpensive method for finding and analyzing intermittent and critical events or faults during system operation. play. When writing data to a file, about 50 bytes of memory are required for each data point. Depending on the number of different parameters taken and the logging rate, a 10 day log would be about 4 MB in size. High Speed Logging Many data logging applications require a much higher rate of data recording. This is especially true when the need is to record RF signal samples in a constantly changing environment. Modern radio communication systems, whether they are mobile phones or wireless data networks, usually involve waveforms that are changing power levels or bursting on and off depending on the operating mode. Additionally, in order to conserve power and make the most efficient use of spectrum resources, RF signals are transmitted only when there is information to send or when channel resources are available. If precise power readings can be made across the duration of the signal they can then be analyzed to isolate problems with individual parts. Envelope tracking is a method of modulating the power supply voltage of an RF amplifier so that it operates as efficiently as possible. The supply voltage is varied with the power envelope of the RF signal so that the amplifier always operates near compression. High speed logging is one cost-effective way to evaluate how well the tracking works, showing latencies and the effects of wide and fast signal variations. With logging at higher speeds, the envelope of a waveform can be traced, as shown in Figure 3. When using high speed logging with a LadyBug power sensor, the maximum sample rate is about 250 to 300 μs. This time will vary depending on the computer being used with the sensor. Characterizing the power emanating from the base station for each LTE slot to ensure flatness for each channel over time is another application of high speed logging. The basic type 1 LTE frame (frequency division duplex, or FDD) has an overall length of 10 ms and is further subdivided into 20 individual slots. High speed 26 High Frequency Electronics
4 logging allows measurement of all slots within a single frame. Another use case for high speed data logging involves critical event failure analysis (see Figure 4). In this case we wish to find a signal anomaly that either indicates a failure in the system or an intermittent event that we want to track and analyze further. For this type of analysis measurement triggering capabilities are important to success. The logging software needs the flexibility to match the proper triggering with the expected waveform. With High Speed Logging application software from LadyBug Technologies, multiple triggering options are available. Figure 5 shows the user interface for starting the logging process. The first option is to simply begin logging when the user clicks the start button. The second is to begin logging when the RF power level reaches a preset threshold, such as when looking for an intermittent event within the signal. The third involves supplying the classical external trigger signal coupling the start of measurements to another event detected by a separate instrument. Our fourth and last option allows the user to select a specific time of day to initiate logging. In any 28 High Frequency Electronics
5 case the start of logging can be delayed to better position the acquisition around the data of interest. There are different aspects to be considered when recording large amounts of data over a period of time. The first would be memory usage. The rate at which data is to be recorded and the number of different parameters included in the recording affect the amount of memory needed. As mentioned earlier, when writing data to a file, about 50 bytes of memory are required for each data point. The amount of RAM available within the computer needs to be sufficient for the length of the log, but the more critical issue is the capability of the software being used to view and analyze the data. Different programs vary in their ability to handle large data sets. Notepad is the default text file editor used by the LadyBug high speed logging application. If the file is created with the data tab delimited it can easily be viewed and analyzed using Excel TM. Through the use of data logging software provided by LadyBug Technologies, the USB power sensor provides a cost-effective method for monitoring various processes that involve RF waveforms. Additionally, LadyBug Technologies makes the source code for the High Speed Logging application available for modification and adaptation by the user. About the Author: Orwill Hawkins serves as Vice-President of Marketing at LadyBug Technologies, Santa Rosa, Calif. He has over three decades of management, marketing, engineering and manufacturing experience, and extensive hands-on design and manufacturing experience in the RF, analog, and digital fields. Among the many products he has designed and marketed are a selfcontained RF field disturbance burglar alarm system, a sailboat speedometer, and various robotic servo systems. Additional inventions include a prototype oscilloscope, a CNC cutting system, and various other analog, digital and RF projects. Figure 5 Triggering alternatives to start the logging process with the LadyBug High Speed Logger application. 29
Spectrum and Power Measurements Using the E6474A Wireless Network Optimization Platform
Application Note Spectrum and Power Measurements Using the E6474A Wireless Network Optimization Platform By: Richard Komar Introduction With the rapid development of wireless technologies, it has become
Instruction Manual Service Program ULTRA-PROG-IR
Instruction Manual Service Program ULTRA-PROG-IR Parameterizing Software for Ultrasonic Sensors with Infrared Interface Contents 1 Installation of the Software ULTRA-PROG-IR... 4 1.1 System Requirements...
Power Amplifier Gain Compression Measurements
Technical Brief Power Amplifier Gain Compression Measurements GPIB Private Bus Sweep Out Sweep In Pulse In AC Mod Out Blank/Marker Out Blanking In Overview The 1 db gain compression of an amplifier describes
Agilent U2000 Series USB Power Sensors
Agilent U2000 Series USB Power Sensors GSM Timeslot Burst Power Measurement Product Note Table of Content Introduction 2 Measuring GSM Timeslot 4 Signal Overview of Agilent U2000 5 Series USB Power Sensors
APPLICATION NOTE GaGe CompuScope 14200-based Lightning Monitoring System
APPLICATION NOTE GaGe CompuScope 14200-based Lightning Monitoring System Challenge A customer needed to upgrade an older data acquisition unit for a real-time lightning monitoring system. Unlike many lightning
2.0 System Description
2.0 System Description The wireless alarm system consists of two or more alarm units within a specified range of one another. Each alarm unit employs a radio transceiver, allowing it to communicate with
High Definition Oscilloscopes
PRELIMINARY High Definition Oscilloscopes HDO4000 and HDO6000 Key Features 12-bit ADC resolution, up to 15-bit with enhanced resolution 200 MHz, 350 MHz, 500 MHz, 1 GHz bandwidths Long Memory up to 250
Carlo Canziani Business Development EMEA. 2012 Agilent Technologies
Ottimizzare il tempo di operatività delle batterie nei dispositivi wireless New Innovation Dramatically Improves Battery Current Drain Measurement Accuracy Carlo Canziani Business Development EMEA 1 Wireless
Using R&S FSW for Efficient Measurements on Multi- Standard Radio Base Stations Application Note
Using R&S FSW for Efficient Measurements on Multi- Standard Radio Base Stations Application Note Products: R&S FSW This application note introduces the Multi- Standard Radio Analyzer function of the R&S
WIRELESS INSTRUMENTATION TECHNOLOGY
BS&B WIRELESS, L.L.C. BS&B WIRELESS, L.L.C. WIRELESS INSTRUMENTATION TECHNOLOGY Printed February 2004 BS&B WIRELESS, L.L.C. 7422-B East 46th Place, Tulsa, OK74145 Phone: 918-622-5950 Fax: 918-665-3904
Impedance 50 (75 connectors via adapters)
VECTOR NETWORK ANALYZER PLANAR TR1300/1 DATA SHEET Frequency range: 300 khz to 1.3 GHz Measured parameters: S11, S21 Dynamic range of transmission measurement magnitude: 130 db Measurement time per point:
The Boonton USB Peak Power Sensor, Wi-Fi ac Signals and the ETSI EN Standard
Application Note The Boonton 55006 USB Peak Power Sensor, Wi-Fi 802.11ac Signals and the ETSI EN 300 328 Standard Stephen Shaw Applications Engineer, Boonton Electronics Abstract This application note
Wireless Home Security System
Wireless Home Security System Group: D14 Members: Vaibhav Singh (05D07026) Abhishek Tiwari (05D07028) Sauvik Chowdhury (05D07029) 1. Abstract The project is aimed at designing a low cost and reliable wireless
Wireless Data Logger Monitoring Systems
Wireless Data Logger Monitoring Systems Table of Contents About MadgeTech, Inc. Wireless Systems & Components Wireless Data Loggers 2000A Wireless Data Logger Models MadgeTech Cloud Services MadgeTech
Department of Electrical and Computer Engineering Ben-Gurion University of the Negev. LAB 1 - Introduction to USRP
Department of Electrical and Computer Engineering Ben-Gurion University of the Negev LAB 1 - Introduction to USRP - 1-1 Introduction In this lab you will use software reconfigurable RF hardware from National
Ameritron ATP-102 Tuning Pulser II
Ameritron ATP-102 The Ameritron ATP-102 relieves temperature related stress on amplifiers, tuners, and dummy loads while allowing proper system adjustments. It allows amplifiers to be properly adjusted
Testing Radar Transmitter Amplitude and Timing Stability using the Agilent 8990B Peak Power Analyzer
Testing Radar Transmitter Amplitude and Timing Stability using the Agilent 8990B Peak Power Analyzer Application Note Introduction During the design, manufacturing, or even maintenance of a radar transmitter,
PXI. www.aeroflex.com. GSM/EDGE Measurement Suite
PXI GSM/EDGE Measurement Suite The GSM/EDGE measurement suite is a collection of software tools for use with Aeroflex PXI 3000 Series RF modular instruments for characterising the performance of GSM/HSCSD/GPRS
Data Logger & Net Client Software (Windows, ipad, Android) Instant On. Touch. Drop & Drag Opera on. No more proprietary display equipment!
Data Logger & Net Client Software (Windows, ipad, Android) builds an Intelligent HMI system Instant On. Touch. Drop & Drag Opera on. No more proprietary display equipment! Running a HMI system with your
Universal Form-factor. Wi Fi Troubleshooting Made Easy
AirMedic USB AirMedic USB is a powerful, easy-touse and affordable spectrum analysis tool that brings Wi-Fi troubleshooting to entry-level users. Built upon AirMagnet expertise in Wi-Fi troubleshooting,
MANUAL FOR RX700 LR and NR
MANUAL FOR RX700 LR and NR 2013, November 11 Revision/ updates Date, updates, and person Revision 1.2 03-12-2013, By Patrick M Affected pages, ETC ALL Content Revision/ updates... 1 Preface... 2 Technical
NEW. EVEN MORE data acquisition and test stand automation
NEW EVEN MORE data acquisition and test stand automation the new class of data The plug&play complete package User benefits Expert Series is the latest generation of data acquisition Complete hardware
Versions. Q.station Q.station T. Q.station D. Q.station DT x x
Most important features: Very high data rates up to 100 khz each channel 100 khz at 16 channels, 10 khz at 128 channels 64 Q.bloxx modules connectable Ethernet interface for configuration and data output
Bidirectional wireless communication using EmbedRF
Bidirectional wireless communication using EmbedRF 1. Tools you will need for this application note... 2 2. Introduction... 3 3. Connect EmbedRF Board to USB Interface Board... 3 4. Install and Run EmbedRF
4310/4320 Wireless Position Monitor Burst Configuration and Diagnostics
Instruction Manual Supplement 4310/4320 Wireless Position Monitor 4310/4320 Wireless Position Monitor Burst Configuration and Diagnostics This document applies to: Fisher 4320 Device Type 1308 (hex) 4872
Agilent 8990B Peak Power Analyzer
Agilent 8990B Peak Power Analyzer Pulse Radar Power Measurement Demo Guide Table of Contents Introduction 2 Demonstration Preparation 3 Demo 1: 14-Pulse Characterization Measurement Demonstrate the capability
Three Levels of Data-Logging Software from National Instruments
Three Levels of Data-Logging Software from National Instruments One of the most common data acquisition applications is simply logging acquired data to disk or a database for future analysis. Most National
I2C PRESSURE MONITORING THROUGH USB PROTOCOL.
I2C PRESSURE MONITORING THROUGH USB PROTOCOL. Product Details: To eradicate human error while taking readings such as upper precision or lower precision Embedded with JAVA Application: Technology Used:
Interactive Logging with FlukeView Forms
FlukeView Forms Technical Note Fluke developed an Event Logging function allowing the Fluke 89-IV and the Fluke 189 models to profile the behavior of a signal over time without requiring a great deal of
Calibration Guide. Agilent Technologies ESG Vector Signal Generator
Calibration Guide Agilent Technologies ESG Vector Signal Generator This guide applies to signal generator models and associated serial number prefixes listed below. Depending on your firmware revision,
Accurate Measurement of the Mains Electricity Frequency
Accurate Measurement of the Mains Electricity Frequency Dogan Ibrahim Near East University, Faculty of Engineering, Lefkosa, TRNC dogan@neu.edu.tr Abstract The frequency of the mains electricity supply
Dash 18X / Dash 18 Data Acquisition Recorder
75 Dash 18X / Dash 18 Data Acquisition Recorder QUICK START GUIDE Supports Recorder System Software Version 3.1 1. INTRODUCTION 2. GETTING STARTED 3. HARDWARE OVERVIEW 4. MENUS & BUTTONS 5. USING THE DASH
TRACTION NETWORK MONITORING AND PROTECTION SYSTEM SMTN-3 CITY ELECTRIC TRANSPORT RAILWAYS METRO INDUSTRY
TRACTION NETWORK MONITORING AND PROTECTION SYSTEM SMTN-3 CITY ELECTRIC TRANSPORT RAILWAYS METRO INDUSTRY 2 TRACTION NETWORK MONITORING AND PROTECTION SYSTEM Traction network monitoring and protection system,
GSM and Similar Architectures Lesson 07 GSM Radio Interface, Data bursts and Interleaving
GSM and Similar Architectures Lesson 07 GSM Radio Interface, Data bursts and Interleaving 1 Space Division Multiple Access of the signals from the MSs A BTS with n directed antennae covers mobile stations
Temperature Alert. LAN-based Temperature and Humidity Data Logger
Temperature Alert LAN-based Temperature and Humidity Data Logger LAN-based Temperature and Humidity Monitoring - Supports Simultaneous WiFi and Hardwired Interfaces -20 C to +60 C (-4 F to +140 F) Standard
TFA. KlimaLogg Pro. User Manual. Revision: 0.1
TFA KlimaLogg Pro User Manual Revision: 0.1 Table of Contents Overview... 2 Getting Started... 2 Setting up the KlimaLogg Pro device... 2 Installing the USB-Stick... 2 Installation... 2 System Requirements...
IDD-213T User Manual. (Rev. 1.0) China Aerospace Telecommunications Limited
(Rev. 1.0) China Aerospace Telecommunications Limited Contents 1. Introduction......3 2. Specifications...4 2.1 External Interface... 4 2.2 Status Indicator...... 5 2.3 Technical Parameters... 6 3. Device
computer radio control system
extended serie Receivers 1 Introduction GLISH FW. ver. 3.10 Jeti DUPLEX Receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2,4 GHz frequency band. DUPLEX
Jeff Thomas Tom Holmes Terri Hightower. Learn RF Spectrum Analysis Basics
Jeff Thomas Tom Holmes Terri Hightower Learn RF Spectrum Analysis Basics Learning Objectives Name the major measurement strengths of a swept-tuned spectrum analyzer Explain the importance of frequency
SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]
SMS Alarm Messenger SMSPro_Setup Revision 090210 [Version 2.2] ~ 1 ~ Contents 1. How to setup SMS Alarm Messenger?... 3 2. Install the SMSPro_Setup software... 5 3. Connection Type... 6 4. Connection Port
Building a Simulink model for real-time analysis V1.15.00. Copyright g.tec medical engineering GmbH
g.tec medical engineering GmbH Sierningstrasse 14, A-4521 Schiedlberg Austria - Europe Tel.: (43)-7251-22240-0 Fax: (43)-7251-22240-39 office@gtec.at, http://www.gtec.at Building a Simulink model for real-time
Cisco Spectrum Expert Wi-Fi
Cisco Spectrum Expert Wi-Fi Overview The Cisco Spectrum Expert Wi-Fi integrates with the Cisco Unified Wireless Network to deliver real-time spectrum intelligence for Wi-Fi networks. This industry-leading
Numerical Parameters Analysis of Boonton 4540 Peak Power Meter
Application Note Numerical Parameters Analysis of Boonton 4540 Peak Power Meter Mazumder Alam Product Marketing Manager, Boonton Electronics Introduction The Boonton 4540 series RF peak power meters consisting
Monitoring Software using Sun Spots. Corey Andalora February 19, 2008
Monitoring Software using Sun Spots Corey Andalora February 19, 2008 Abstract Sun has developed small devices named Spots designed to provide developers familiar with the Java programming language a platform
Unmatched RF Spectrum Analysis
Datasheet: AirMagnet Spectrum XT AirMagnet Spectrum XT is the industry s first professional spectrum analyzer solution that combines in-depth RF analysis with real-time WLAN information for quicker and
Agilent BenchVue Software (34840B) Data capture simplified. Click, capture, done. Data Sheet
Agilent BenchVue Software (34840B) Data capture simplified. Click, capture, done. Data Sheet Use BenchVue software to: Visualize multiple measurements simultaneously Easily capture data, screen shots and
The Heartbeat behind Portable Medical Devices: Ultra-Low-Power Mixed-Signal Microcontrollers
The Heartbeat behind Portable Medical Devices: Ultra-Low-Power Mixed-Signal Microcontrollers The proliferation of sophisticated yet affordable personal medical devices is transforming the health care industry,
GA1000 oscilloscope PC Software Instruction
GA1000 oscilloscope PC Software Instruction 1. GAScope PC Software Overview GAScope PC software is a supplementary software of oscilloscope GA1000 series. It could be used for observing waveforms and operating
Spectrum Analysis How-To Guide
Spectrum Analysis How-To Guide MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. Motorola Solutions, Inc. 2012. All rights reserved. Spectrum Analysis 3 Contents
NEW FEATURES IN VERSION 1.4
NEW FEATURES IN VERSION 1.4 Some significant improvements and new capabilities have been introduced to the Goldeneagle HD with software/firmware version 1.4, released in February 2007 and FREE available
Interference Analysis
Application Note Interference Analysis JD7105A Base Station Analyzer / JD7106A RF Analyzer Introduction This document presents an overview of signal interference in RF wireless networks as well as a brief
AC3200 INTELLIGENT BROADBAND AMPLIFIER
Kari Mäki 12.11.2009 1(8) AC3200 INTELLIGENT BROADBAND AMPLIFIER AC3200 is the latest leading-edge addition to AC family with extended frequency and gain ranges and integrated electrical controls in both
Application Note Noise Frequently Asked Questions
: What is? is a random signal inherent in all physical components. It directly limits the detection and processing of all information. The common form of noise is white Gaussian due to the many random
Data Sheet 8140 TETRA AirAnalyzer
Data Sheet 8140 TETRA AirAnalyzer boosting wireless efficiency 1 Ensuring safe and reliable communication when you need it most Mobile networks following the TETRA standard form a basis for successful
*Author for Correspondence. Key Words: Amplifier Lm386, Transmitter, Receiver, Solar Panel, Laser Diode
LASER COMMUNICATION SYSTEM USING SOLAR CELL *G. Sujatha 1, P. Vikram 2 and P. Karthik 2 1 College of Food and Dairy Technology, Koduvalli, Alamathy (PO), Chennai 600052 2 Loyola-Icam college of Engineering
USB-500 Series Stand-Alone, Low-Cost Data Loggers
Stand-Alone, Low-Cost Data Loggers Features Stand-alone, remote data loggers Measure temperature, humidity, voltage, or current 1 or 2 channels Low cost, small size Battery powered Software Included, easy-to-use
The Director Software V4 and the Scalability Tool
The Director Software V4 and the Scalability Tool Small bench top tablet presses can be used to successfully transfer a product into larger production machines provided that the proper tooling and speeds
125 8880 telstra.com/ppmbb visit a telstra store or partner GETTING TO KNOW YOUR
FOR MORE INFORMATIoN: 125 8880 telstra.com/ppmbb visit a telstra store or partner GETTING TO KNOW YOUR Telstra PRE-paid 4G wi-fi LET S GET THIS SHOW ON THE ROad WHAT S INSIDE Your Telstra Pre-Paid 4G Wi-Fi
Dash 8Xe / Dash 8X Data Acquisition Recorder
75 Dash 8Xe / Dash 8X Data Acquisition Recorder QUICK START GUIDE Supports Recorder System Software Version 2.0 1. INTRODUCTION 2. GETTING STARTED 3. HARDWARE OVERVIEW 4. MENUS & BUTTONS 5. USING THE DASH
Test & Data Management Software
Test & Data Management Software TDMS protective relays energy meters transducers power quality CT-VT-PT transformers ground grid circuit breakers batteries surge arresters The Integrated Testing Solution
CRE Monitor Instructions Manual
CRE Monitor Instructions Manual CRE TECHNOLOGY believes that all information provided herein is correct and reliable and reserves the right to update at anytime. CRE TECHNOLOGY does not assume any responsibility
Event Log. Chapter 7 Event Log... 2 7.1 Event Log Management... 4 7.1.1 Excel Editing... 6 7.2 Create a New Event Log... 10
Chapter 7 Event Log... 2 7.1 Event Log Management... 4 7.1.1 Excel Editing... 6 7.2 Create a New Event Log... 10 1 Chapter 7 Event Log Event log is used to define the content of an event and the conditions
TDMS Test & Data Management Software
Test & Data Management Software TDMS protective relays energy meters transducers power quality CT-VT-PT transformers ground grid circuit breakers batteries surge arresters The Integrated Testing Solution
Jeff Thomas Tom Holmes Terri Hightower. Learn RF Spectrum Analysis Basics
Jeff Thomas Tom Holmes Terri Hightower Learn RF Spectrum Analysis Basics Agenda Overview: Spectrum analysis and its measurements Theory of Operation: Spectrum analyzer hardware Frequency Specifications
mysensors mysensors Wireless Sensors and Ethernet Gateway Quick Start Guide Information to Users Inside the Box mysensors Ethernet Gateway Quick Start
mysensors Information to Users mysensors Wireless Sensors and Ethernet Gateway Quick Start Guide This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant
Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual
Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS
GE Grid Emulator. 7.5 kva 200 kva
Grid emulators are specially designed to emulate grid disturbances. All range of grid emulators has different programmable parameters that allow flexibility to evaluate different kind of scenarios. They
Event Log. Chapter 7 Event Log... 2 7.1 Event Log Management... 3 7.1.1 Excel Editing... 5 7.2 Create a New Event Log... 9
Chapter 7 Event Log... 2 7.1 Event Log Management... 3 7.1.1 Excel Editing... 5 7.2 Create a New Event Log... 9 1 Chapter 7 Event Log Event log is used to define the content of an event and the conditions
RF Measurements Using a Modular Digitizer
RF Measurements Using a Modular Digitizer Modern modular digitizers, like the Spectrum M4i series PCIe digitizers, offer greater bandwidth and higher resolution at any given bandwidth than ever before.
DS1621 Digital Thermometer and Thermostat
Digital Thermometer and Thermostat www.dalsemi.com FEATURES Temperature measurements require no external components Measures temperatures from 55 C to +125 C in 0.5 C increments. Fahrenheit equivalent
Instructions for Setting the T560 Digital Delay Generator for the Target Delay
Instructions for Setting the T560 Digital Delay Generator for the Target Delay Important! These instructions are only to be followed by beam-line operators who have been trained to operate the target!!
1 0 0 1 e s p i o n s.com. V680 GPS Watch User s Manual
1 V680 GPS Watch User s Manual 2 Table of Contents Chapter I Preface..4 I.General...4 II.Notices..4 Chapter II about the Device.5 1. Appearance..5 2. Product Features.5 3. Product Specification.6 (1).Technical
EDM SOFTWARE ENGINEERING DATA MANAGEMENT SOFTWARE
EDM SOFTWARE ENGINEERING DATA MANAGEMENT SOFTWARE MODERN, UPATED INTERFACE WITH INTUITIVE LAYOUT DRAG & DROP SCREENS, GENERATE REPORTS WITH ONE CLICK, AND UPDATE SOFTWARE ONLINE ipad APP VERSION AVAILABLE
Vehicle data acquisition using CAN By Henning Olsson, OptimumG henning.olsson@optimumg.com
Vehicle data acquisition using By Henning Olsson, OptimumG henning.olsson@optimumg.com Introduction: Data acquisition is one of the best tools to increase the understanding of vehicle behavior. One can
DEVELOPMENT OF DEVICES AND METHODS FOR PHASE AND AC LINEARITY MEASUREMENTS IN DIGITIZERS
DEVELOPMENT OF DEVICES AND METHODS FOR PHASE AND AC LINEARITY MEASUREMENTS IN DIGITIZERS U. Pogliano, B. Trinchera, G.C. Bosco and D. Serazio INRIM Istituto Nazionale di Ricerca Metrologica Torino (Italia)
Vehicle Off-Line GPS and Fuel Monitoring System (post trip vehicle monitoring system) Riga ; Latvia www.guardmagic.com
Vehicle Off-Line GPS and Fuel Monitoring System (post trip vehicle monitoring system) About Off-Line monitoring Off-Line vehicle and fuel monitoring system is the most inexpensive and the most cost effective
INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA
COMM.ENG INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA 9/6/2014 LECTURES 1 Objectives To give a background on Communication system components and channels (media) A distinction between analogue
Technical Information
Technical Information TI No. WL 80-63 E April 2001 Rolling Bearing Diagnosis with the FAG Bearing Analyser Rolling Bearings State-Of-The-Art, Condition-Related Monitoring of Plants and Machines Unforeseen
Application of a Web-based Monitoring and Control system in Plastic Rotational Moulding Machine
Application of a Web-based Monitoring and Control system in Plastic Rotational Moulding Machine Mário Rodrigues 1, José Mendes 2, and Jaime Fonseca 3 University of Minho 1,2,3 Dept. of Industrial Electronics
ugrid Testbed. Rein in microgrid complexity. With ease.
ugrid Testbed. Rein in microgrid complexity. With ease. Outsmart the microgrid. ugrid Testbed Ultimate test solution for microgrid control system verification What is a microgrid? Microgrid is a collection
MCTS Guide to Microsoft Windows 7. Chapter 10 Performance Tuning
MCTS Guide to Microsoft Windows 7 Chapter 10 Performance Tuning Objectives Identify several key performance enhancements Describe performance tuning concepts Use Performance Monitor Use Task Manager Understand
Attenuation (amplitude of the wave loses strength thereby the signal power) Refraction Reflection Shadowing Scattering Diffraction
Wireless Physical Layer Q1. Is it possible to transmit a digital signal, e.g., coded as square wave as used inside a computer, using radio transmission without any loss? Why? It is not possible to transmit
GETTING TO KNOW YOUR PRE-PAID TELSTRA WI-FI 4G
GETTING TO KNOW YOUR PRE-PAID TELSTRA WI-FI 4G LET S GET THIS SHOW ON THE ROAD You must be excited about your brand new Pre-Paid Telstra Wi-Fi 4G. This guide will help you get connected as quickly and
What is LOG Storm and what is it useful for?
What is LOG Storm and what is it useful for? LOG Storm is a high-speed digital data logger used for recording and analyzing the activity from embedded electronic systems digital bus and data lines. It
ARA Digital Train Radio System Functional Requirements For Australian Metropolitan Railway Operators. 19 September 2005
ARA Digital Train Radio System Functional Requirements For Australian Metropolitan Railway Operators 19 September 2005 1. General 1.1 General 1.1.1 Scope and Standard The Australian Metropolitan Railway
WeatherLink for Alarm Output. Introduction. Hardware Installation and Requirements. Addendum
WeatherLink for Alarm Output Addendum Introduction This Streaming Data Logger is designed to provide an electrical interface between a Vantage Pro2, Vantage Vue, or Vantage Pro weather station console
Basics of RF Amplifier Measurements with the E5072A ENA Series Network Analyzer
Basics of RF Amplifier Measurements with the E5072A ENA Series Network Analyzer Application Note Introduction The RF power amplifier is a key component used in a wide variety of industries such as wireless
Radiological Assessment Display and Control System
Features Fast, real-time data acquisition and control Highly reliable communication with remote terminal units Collecting, converting, integrating and analyzing data from all monitors Detecting, annunciating
The BSN Hardware and Software Platform: Enabling Easy Development of Body Sensor Network Applications
The BSN Hardware and Software Platform: Enabling Easy Development of Body Sensor Network Applications Joshua Ellul jellul@imperial.ac.uk Overview Brief introduction to Body Sensor Networks BSN Hardware
Silent Fan. Brief Description. Benefits. Functional Diagram. Silent Fan. Controller
Silent Fan Issue May 2009 Product Silent Fan Pages 6 Brief Description Many versions of Fujitsu Technology Solutions mainboards feature Silent Fan, a fan control and monitoring function; this technology
IMMUNITY TESTING TO IEC SPECIFICATIONS by Thomas C. Moyer, Amplifier Research
IMMUNITY TESTING TO IEC SPECIFICATIONS by Thomas C. Moyer, Amplifier Research SUMMARY The European Union of 15 member countries has a population of 370 million people and it represented 16% of the US exports
Fluke 89-IV & 189 Event Logging
Fluke 89-IV & 189 Event Logging FlukeView Forms Technical Note One of the major features of the Fluke 89-IV & 189 meters are their ability to "do logging". This technical note explains what kind of logging
Keysight Technologies N1918A Power Analysis Manager and U2000 Series USB Power Sensors. Demo Guide
Keysight Technologies N1918A Power Analysis Manager and U2000 Series USB Power Sensors Demo Guide Introduction This demonstration guide helps you to get familiar with the basic setup and coniguration requirements
Agilent PN 8753-1 RF Component Measurements: Amplifier Measurements Using the Agilent 8753 Network Analyzer. Product Note
Agilent PN 8753-1 RF Component Measurements: Amplifier Measurements Using the Agilent 8753 Network Analyzer Product Note 2 3 4 4 4 4 6 7 8 8 10 10 11 12 12 12 13 15 15 Introduction Table of contents Introduction
Quick Start Guide. MRB-KW01 Development Platform Radio Utility Application Demo MODULAR REFERENCE BOARD
Quick Start Guide MRB-KW01 Development Platform Radio Utility Application Demo MODULAR REFERENCE BOARD Quick Start Guide Get to Know the MRB-KW01x Module UART Selector ANT 1 RFIO (TX/RX) USB 2.0 Serial
Constructing a precision SWR meter and antenna analyzer. Mike Brink HNF, Design Technologist.
Constructing a precision SWR meter and antenna analyzer. Mike Brink HNF, Design Technologist. Abstract. I have been asked to put together a detailed article on a SWR meter. In this article I will deal
IMMUNITY TESTING FOR THE CE MARK By Rodger Gensel, Product Line Applications Specialist
IMMUNITY TESTING FOR THE CE MARK By Rodger Gensel, Product Line Applications Specialist SUMMARY The European Union (EU) currently has 25 member countries with 2 additional countries to be added in 2007.
DAC Express Release 3.4 (VT9801B)
DAC Express Release 3.4 (VT9801B) DAC Express 3.4 Highlights n EX1629 48 Channel high performance remote strain measurement unit n Display Wizard for fast test setups integrated web server for global access
OVERVIEW OF THE TELEGUARD HOME SECURITY SYSTEM
OVERVIEW OF THE TELEGUARD HOME SECURITY SYSTEM 12. WIDE RANGE OF POTENTIAL INPUT DEVICES PIR s, Smoke Alarms, Emergency Transmitters, Environmental / Gas Leak Sensors, Break-in or Inactivity Detectors
CS263: Wireless Communications and Sensor Networks
CS263: Wireless Communications and Sensor Networks Matt Welsh Lecture 4: Medium Access Control October 5, 2004 2004 Matt Welsh Harvard University 1 Today's Lecture Medium Access Control Schemes: FDMA TDMA