Evaluation Board. i-modul and Socket. Manual

Transcription

1 Evaluation Board i-modul and Socket Manual

2

3 Copyright March 14 INSYS MICROELECTRONICS GmbH Any duplication of this manual is prohibited. All rights on this documentation and the devices are with INSYS MICROELECTRONICS GmbH Regensburg. Trademarks The use of a trademark not shown below is not an indication that it is freely available for use. MNP is a registered trademark of Microcom Inc. IBM PC, AT, XT are registered trademarks of International Business Machine Corporation. INSYS, e-mobility LSG and e-mobility PLC are registered trademarks of INSYS MICROELECTRONICS GmbH. Windows is a registered trademark of Microsoft Corporation. Linux is a registered trademark of Linus Torvalds. Publisher: INSYS MICROELECTRONICS GmbH Hermann-Köhl-Str. 22 D Regensburg, Germany Phone: Fax: info@insys-icom.com Internet: Date: Mar-14 Item: Version: 1.0 Language: EN

4 Content 1 Overview Technical Specification Connectors Multi-pin connectors Jumpers Initial operation Configuration of i-modules Configuration of Socket mode Step-by-step inital operation instructions Evaluation Board and module plug ports Circuit diagram Mar-14

5 1 Overview The Evaluation board is intended to be used for customer specific implementations and tests for the following INSYS i-modul and INSYS socket products: Modem ISDN GSM EDGE HSPA Ethernet GPRS WLAN Bluetooth Special Features: Socket and i-modul support D-SUB listen ports for RxD and TxD Phone jack for speaker Phone jack for microphone Terminal and coaxial power supply Support for 3.3 and 5V modules, adjustable by jumper

6 Technical Specification Fehler! Kein Text mit angegebener Formatvorlage im Dokument. 2 Technical Specification Dimensions: Power supply: Current drain: 160mm x 100mm 9 VAC - 12 VAC 10 VDC - 15 VDC max. 1.5A (Peak at GSM) max. 0.3A (ISDN, Modem, Ethernet, WLAN) 2.1 Connectors CON401 CON11 CON16 CON301 CON303/CON304 CON2 CON3 CON13 CON12 Screwing terminal for power supply Coax jack for power supply SUB D jack for RS232 connection RJ45 jack for Modem/ISDN/Ethernet- connection Screwing terminal for phone connection SUB D jack for RS232 listen port RxD SUB D jack for RS232 listen port TxD 3,5mm jack for speaker 3,5mm jack for microphone 2.2 Multi-pin connectors CON18 JP100 CON110 J401 CON17 Multi-pin connector for field strength, OH, status, sync Multi-pin connector for RS232 signals Multi-pin connector for RESET Multi-pin connector GND and VCC connection Multi-pin connector UE/UA/UE2/UA2

7 2.3 Jumpers JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP100 JP8 JP9 JP10 JP11 JP12 JP13 Setting for i-modul (Pin assignment) Setting for i-modul (Pin assignment) Setting for i-modul (Pin assignment) Setting for i-modul (Pin assignment) Setting for i-modul (Pin assignment) Setting for i-modul (Pin assignment) Microphone supply Jumpers for serial interface Jumper for on-board speaker Switching between 3,3V (open) und 5V (bridged) Setting for Socket Setting for Socket Setting for Socket Setting for Socket

8 Initial operation Fehler! Kein Text mit angegebener Formatvorlage im Dokument. 3 Initial operation In principle there is a difference in configuration of i-modules and socket modules. Depending on the plugged-on module the correct jumper settings must be checked before switching on the evaluation board. Warning! With voltage not adjusted properly the is danger of overheating of components.. Hot surfaces! Take care jumper JP9 is configured properly. In case components become hot, cut electrical supply and have components cool down Danger of severe injury and of damage of components

9 3.1 Configuration of i-modules Use jumpers J1-J6 and JP9 (bridged = 5V) if you want to configure an i-modul Modem/ISDN or an i-modul Ethernet/WLAN bridge. The jumper settings for i-modul Modem correspond to the jumper settings for i- modul ISDN. Configuration Modem/ISDN Configuration Ethernet a/wlan bridge a Configuration Ethernet b/wlan bridge b Note When using an i-modul GSM, GPRS, WLAN serial and Bluetooth the jumpers JP1 JP6 as well as the connectors CON301 and CON303/304 are without function.

10 Initial operation Fehler! Kein Text mit angegebener Formatvorlage im Dokument. 3.2 Configuration of Socket mode In order to configure the evaluation board for socket modules (Modem/Ethernet, ISDN) the jumpers JP9 JP13 have to be used. JP9 should be open with 3,3Vmodules. The jumper settings for Modem correspond to the Ethernet settings. Configuration Modem Configuration Ethernet Configuration ISDN 3.3 Step-by-step inital operation instructions Please follow these steps when plugging on a new i-modul or socket module: 1. Plug on the module carefully. 2. Configure the modul type with jumpers JP1 JP6 and JP9 (i-modul and socket) respectively JP10 JP13 (socket only). 3. Connect the serial interface CON16 by a standard serial cable with your computer. 4. Connect the power supply either by connector CON401 or by jack CON11. The polarity is irrelevant. 5. Start your terminal program on your computer (e.g. Hyperterminal or TeraTerm). 6. Switch on power supply (LED PWR is lit). 7. Type AT<RETURN> in the terminal program of your computer. 8. The module answers by sending OK back to the terminal program. When using a module without the autobauding feature you have to check the baud rate of your terminal program before the communication can be established successfully. If there is no answer from the module even after checking the communication settings you have to immediately switch off the power supply and check if the i-modul or socket module is plugged on correctly and if all jumpers are set as described in this manual.

11 4 Evaluation Board and module plug ports Port for i-modules 144/336/56k GSM GPRS Bluetooth Ethernet WLAN

12 Evaluation Board and module plug ports Fehler! Kein Text mit angegebener Formatvorlage im Dokument. Port for i-modul ISDN HIT ISDN HIX Note The bolt has to be removed before plugging on the module.

13 Port for socket modules

14 Circuit diagram Fehler! Kein Text mit angegebener Formatvorlage im Dokument. 5 Circuit diagram

15

16 Circuit diagram Fehler! Kein Text mit angegebener Formatvorlage im Dokument.

17

18