GONAR - SYSTEMS INTERNATIONAL TUNNELING AND GEOTECHNICAL SYSTEMS
|
|
- Tracey Harvey
- 8 years ago
- Views:
Transcription
1 GONAR - SYSTEMS INTERNATIONAL TUNNELING AND GEOTECHNICAL SYSTEMS 1
2 GSI System Technical Data Technical Data Unit R25 R32L R32N R32S R38 R51N T76N T76S T103N T103S Outer mm inner mm cross sectional area mm Ultimate load *1 kn Yield load *1 kn tensile strenght *1 N/mm yield strenght *1 N/mm kg/m Thread standard ISO ISO 1720 Internal standard Steel grade Acc. to. EN Delivery lenghts m 1, 2, 3, 4, 6 1, 2, 3, 4 2, 3 *1 The ultimate load and yield load capacity are measured values. The tensile-/yield strenghts are calculated average values. 2
3 GONAR - SYSTEMS INTERNATIONAL Advantages and Characteristics the main advantages of the GSI Anchor bar are: Fast drilling and placing due to drilling, anchor installation and grouting in a single operation Neither separate anchor installation nor removal of casing and drill rods Similar installation methods for all ground conditions Choice of drill bits for different ground conditions The hollow core not only serves for flushing with air or water during drilling, but also for grouting the anchor tendon Flexibility in length by using couplers Ability to work with small drill rigs without casing in restricted headroom conditions Accommodation of needs for enhanced protection against corrosion upon request The accepted high standard of quality control from production stage to installation of the GSI Anchors ensures consistent quality The GSI Anchor has an advantage in all applications where normally cased drilling is required. The GSI Anchor System allows for anchoring in both cohesive and noncohesive ground, even under limited space conditions. Content GSI Anchor System Technical Data 2 System R25 4 System R32 5 System R38 6 System R51 7 System T76 8 System T103 9 Accessories
4 GSI self drilling anchor R25 Hammer Shank adapter Adapter coupling Anchor rod Adapter coupling Anchor rod Bit COP 1238-R R32-R25 COP 1838-R Rod R25 Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m R The way of order For 1 m long For 2 m long For 3 m long For 4 m long For 6 m long R Coupling R25 tensile strength R m yield strength R p0,2 Diameter Length Catalogue no Key size Length Catalogue no. Nut R Spherical nut R Anchor plate R25 Bits with thread R25 Dimension Hole Catalogue no. 150x150x x200x Catalogue no. Description kg Cross bit ø42 without sintered carbide insert Cross bit ø42 with sintered carbide insert Cross bit ø51 without sintered carbide insert Cross bit ø51 with sintered carbide insert Button bit ø42 without sintered carbide insert Button bit ø42 with sintered carbide insert Button bit ø51 without sintered carbide insert Button bit ø51 with sintered carbide insert Asymmetrical bit ø51 without sintered carbide insert Asymmetrical bit ø51 with sintered carbide insert Cross bit Button bit Asymmetrical bit 4
5 GSI self drilling anchor R32L, R32N, R32S Hammer Shank adapter Adapter coupling Anchor rod Adapter coupling Anchor rod Bit COP 1238-R32 COP 1838-R32 COP 1432-R32 COP 1238-R38 COP 1838-R38 COP 1432-R R32-R R38-R Rod R32 Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity tensile strength R m yield strength R p0,2 mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m R32/ø22 L R32/ø18.5 N R32/ø15 S The way of order For 1 m long For 2 m long For 3 m long For 4 m long For 6 m long R32/ø22 L R32/ø18.5 N R32/ø15 S Diameter Length Catalogue no. Coupling R Key size Length Catalogue no. Nut R Spherical nut R Anchor plate R32 Bits with thread R32 Dimension Hole Catalogue no. 150x150x x200x Description Catalogue no. kg Cross bit ø45 without sintered carbide insert Cross bit ø45 with sintered carbide insert Cross bit ø51 without sintered carbide insert Cross bit ø51 with sintered carbide insert Cross bit ø64 without sintered carbide insert Cross bit ø64 with sintered carbide insert Cross bit ø76 without sintered carbide insert Cross bit ø76 with sintered carbide insert Button bit ø51 without sintered carbide insert Button bit ø51 with sintered carbide insert Button bit ø76 without sintered carbide insert Button bit ø76 with sintered carbide insert Asymmetrical bit ø51 without sintered carbide insert Asymmetrical bit ø51 with sintered carbide insert Asymmetrical bit ø76 without sintered carbide insert Asymmetrical bit ø76 with sintered carbide insert Clay bit ø76 / Clay bit ø / / 1.25 Clay bit ø Cross bit Button bit Asymmetrical bit Clay bit It is not offered in Germany market 5
6 GSI self drilling anchor R38 Hammer Shank adapter Adapter coupling Anchor rod Adapter coupling Anchor rod Bit COP 1238-R38 COP 1838-R R38-R COP 1432-R38 COP 1238-T T38-R Rod R38 Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity tensile strength R m yield strength R p0,2 mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m R The way of order R38 For 1 m long For 2 m long For 3 m long For 4 m long For 6 m long Coupling R38 Diameter Length Catalogue no. 51, Key size Length Catalogue no. Nut R Spherical nut R Anchor plate R38 Dimension Hole Catalogue no. 200x200x Bits with thread R38 Description Catalogue no. kg Cross bit ø64 without sintered carbide insert Cross bit ø64 with sintered carbide insert Cross bit ø76 without sintered carbide insert Cross bit ø76 with sintered carbide insert Cross bit ø90 without sintered carbide insert Cross bit ø90 with sintered carbide insert Button bit ø76 without sintered carbide insert Button bit ø76 with sintered carbide insert Button bit ø90 without sintered carbide insert Button bit ø90 with sintered carbide insert Button bit ø115 without sintered carbide insert Button bit ø115 with sintered carbide insert Asymmetrical bit ø76 without sintered carbide insert Asymmetrical bit ø76 with sintered carbide insert Asymmetrical-button bit ø76 without sintered carbide insert Asymmetrical-button bit ø76 with sintered carbide insert Asymmetrical-button bit ø90 without sintered carbide insert Asymmetrical-button bit ø90 with sintered carbide insert Clay bit ø94 / Clay bit ø / / 1.40 Clay bit ø130 / Clay bit ø / / 1.70 Cross bit Button bit Asymmetrical bit Asymetrical-button bit Clay bit It is not offered in Germany market 6
7 GSI self drilling anchor R51 Hammer Shank adapter Adapter coupling Anchor rod Adapter coupling Anchor rod Bit COP 1238-R38 COP 1838-R38 COP 1238-T R38-R T38-R Rod R51 Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity tensile strength R m yield strength R p0,2 mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m R51/ø33 N The way of order For 1 m long For 2 m long For 3 m long For 4 m long For 6 m long R51/ø33 N Coupling R51 Diameter Length Catalogue no Key size Length Catalogue no. Nut R Spherical nut R Anchor plate R51 Dimension Hole Catalogue no. 200x200x Bits with thread R51 Description Catalogue no. kg Cross bit ø76 without sintered carbide insert Cross bit ø76 with sintered carbide insert Cross bit ø90 without sintered carbide insert Cross bit ø90 with sintered carbide insert Button bit ø76 without sintered carbide insert Button bit ø76 with sintered carbide insert Button bit ø90 without sintered carbide insert Button bit ø90 with sintered carbide insert Button bit ø100 without sintered carbide insert Button bit ø100 with sintered carbide insert Button bit drop center ø115 without sintered carbide insert Button bit drop center ø115 with sintered carbide insert Asymmetrical-Button bit ø90 without sintered carbide insert Asymmetrical-Button bit ø90 with sintered carbide insert Cross-Button bit ø115 without sintered carbide insert Cross-Button bit ø115 with sintered carbide insert Clay bit ø Clay bit ø Cross bit Button bit Button bit drop center Asymetrical-button bit Cross-button bit Clay bit It is not offered in Germany market 7
8 GSI self drilling anchor T76 Bar T76 Coupler Bar T76 Bit shank adapters for different hammers on reqest Rod T76 Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity tensile strength Rm yield strength Rp0,2 mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m T76N T76S The way of order For 1 m long For 2 m long For 3 m long For 4 m long For 6 m long T76N T76S Coupling T76 Nut T76 Anchor plate T76 Diameter Length Catalogue no Key size Length Catalogue no Dimension Hole Part no. 250x250x x250x Bits with thread T76 Description Catalogue no. kg Cross bit ø130 without sintered carbide inserts Cross bit ø130 with sintered carbide inserts Cross bit ø200 without sintered carbide inserts Cross bit ø200 with sintered carbide inserts Asymmetrical-button bit ø130 without sintered carbide insert Asymmetrical-button bit ø130 with sintered carbide insert Button bit drop center ø130 with sintered carbide insert Clay bit ø Clay bit ø Clay bit ø Clay bit ø Further drill bits on request Cross bit Asymetrical-button bit Button bit drop center Clay bit It is not offered in Germany market 8
9 GSI self drilling anchor T103 Bar T103 Coupler Bar T103 Bit shank adapters for different hammers on reqest Rod T103 Bits with thread T103 Diameter Length Catalogue no. Coupling T103N Coupling T103S Nut T103 Anchor plate T103 Key size Length Catalogue no Dimension Hole Part no. 300x300x x300x Description Catalogue no. kg Button bit drop center ø280 with sintered carbide insert Clay bit ø Clay bit ø Further drill bits on request Outside internal Aver. eff. cross sectional area Ultimate load capacity Yield load capacity tensile strength Rm yield strength Rp0,2 mm mm mm 2 kn kn N/mm 2 N/mm 2 kg/m T103N T103S The way of order For 1 m long For 2 m long For 3 m long For 4 m long T103N T103S Button bit drop center Clay bit It is not offered in Germany market 9
10 Accessories Adapter for bits Type G1 G2 Catalogue no. R25 R32 R25 R R25 R38 R25 R R32 R25 R32 R R32 R38 R32 R R32 R51 R32 R R38 R25 R38 R R38 R32 R38 R R38 R51 R38 R R38 T76 R38 T R51 R32 R51 R R51 R38 R51 R R51 T76 R51 T T76 R51 T76 R Adapter for injection Type G1 Catalogue no. R25 R R32 R R38 R R51 R T76 T Connector for injection head Type D G1 G2 Catalogue no. GB R25 R GB R25 T GB R32 R GB R32 R GB R32 T GB R38 R GB R38 T GB T38 T GB R32 T GB R38 T GB R32 T GB R38 T GB R51 T
11 Accessories Leading head Type D Catalogue no. GB GB GB GB GB GB Adapter for drilling Type D G1 Catalogue no. 6kt22 35 R kt22 45 R kt22 55 R kt22 42 Ti kt22 53 Ti kt22 65 Ti kt22 45 R Centralizer G1 D Catalogue no. R25 R R R Ti T Ti
12 Our representants: GONAR AUSTRALIA PTY LTD Unit 2, 8 Arunga Driver NSW 2322 Beresfield, Australia tel info@gonaraustralia.com.au TASUM - GONAR s.r.o. Śtrkova Żilina, Slovakia tel fax tasum@tasum.sk GONAR BULGARIA Ltd 18, Parva Bulgarska Armia Str. PO Box 54 BG 1220 Sofia, Bulgaria tel fax info@gonar-bg.com OOO GSI Krasnoarmeyskaya Str Kemerovo, Kemerovo region Russian Federation tel m.cherepanov@gonar-systems.com BOHR-UND ANKERSYSTEME GSI Fuggerallee Oberdorf, Germany Mobile phone mirek.palczynski@gonar-systems.com C.I ENTRELINK S.A Edificio Nueva Granada Calle 72 No Piso 9 Bogota, Colombia tel fax contactenos@entrelink.com.co DYNATRAC (NIGERIA) LTD. Construction & Quarry & Acessories 3 Oluwole Fadojutimi Street Amuwo Odofin Estate Lagos, Nigeria tel fax dynatrac@beta.linkserve.com DUKRAFT LTDA. Buenos Aires, Argentina tel. +54 (11) mobile phone +54 (911) mobile phone +56 (9) gd@dukraft.com DUKRAFT LTDA. Santiago, Chile tel. +56 (2) fax +56 (2) mobile phone +56 (9) fd@dukraft.com EMICO Epuipos para mineria y construcciones sa C/Las Eras, s/s-nave n.2 Pol.Ind Almazcara (Leon), Spain tel fax leon@emico-calsumi.com ERKOM KOMPRESOR MAKINA IMALAT SAN.VE TlC. LTD. ŞTl Alinteri Bul. 17, Cad. 29/E ^ Ostim Ankara, Turkey tel fax erkom@erkom.com.tr GEOTUNNEL S.r.l. Tunneling &Foundation Equipment Molo Ponte Morosini Genova, Italy tel fax info@geotunnel.it NETIS d.o.o Zagreb, Bartolići 45, Croatia tel fax neven.hadziomerspahic@zg.htnet.hr OOO ANKER GEO Sant Petersburg, Russian Federation tel (812) fax +007 (951) mobile phone +007 (951) PRADA SISTEMAS INDUSTRIALES S.L.U. Pol. Ind. A Rana, Calle 7 Parc O Barco de Valdeorras (Orense), Spain tel fax mobile phone admon@psisuministros.com GONAR - Systems International Ltd. 109 Obroki Str., KATOWICE, POLAND tel , fax gsi@gonar.com.pl 12
IBO - Self-drilling Anchor
IBO - Self-drilling Anchor System Components IBO - Self-drilling Anchor IBO - anchor plate IBO - nut with convex seat IBO - coupling with continous inside-thread and middle stop Field of application IBO
More informationVSL GC ANCHORAGE TECHNOLOGY GC ANCHORAGES
VSL GC ANCHORAGE TECHNOLOGY GC ANCHORAGES Technical Data Characteristics Applications VSL S LATEST FOR POST-TENSIONING Meets ETAG with proven materials PT-PLUS duct system for enhanced corrosion protection
More informationContact details HYPOXI DISTRIBUTORS
AUSTRALIA & NEW ZEALAND HYPOXI Australia Pty Ltd First Floor, 119 Foveaux Street Surry Hills NSW 2010 Australia Tel. +61 2 9281 2033 Fax +61 2 9281 2038 Email: australia@hypoxi.com AUSTRIA Email: austria@hypoxi.com
More informationManual tensioning and sealing Pneumatic tensioning and sealing
Hand Tools for Steel Strapping Manual tensioning and sealing Pneumatic tensioning and sealing The Strapex Advantage Hand Tools, Strap and After-Sales Service as a total package The right tool The applications
More informationDECLARATION OF PERFORMANCE NO. HU-DOP_TN-212-25_001
NO. HU-DOP_TN-212-25_001 Product type 212 (TN) 3,5x25 mm EN 14566:2008+A1:2009 NO. HU-DOP_TN-212-35_001 Product type 212 (TN) 3,5x35 mm EN 14566:2008+A1:2009 NO. HU-DOP_TN-212-45_001 Product type 212 (TN)
More informationPPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
More informationSystem. Stability. Security. Integrity. 150 Helical Anchor
Model 150 HELICAL ANCHOR System PN #MBHAT Stability. Security. Integrity. 150 Helical Anchor System About Foundation Supportworks is a network of the most experienced and knowledgeable foundation repair
More informationTolerance +/- 0,5 mm, +/- 0,2 mm. Length 15-350 mm ( standard) SLOTS. 9 5/8 x 36 Ibs/ft. 4 1/2 x 9,5 Ibs/ft. Slotted casing
Slotted casing Tube API 5CT, grade J/K55, R1, R2, STC: 4 1/2 x 9,5 Ibs/ft number of slots / meter number of ranges on circumference number of ranges per linear meter 24 4 6 9 5/8 x 36 Ibs/ft 48 8 6 Slotted
More informationPRESENTATION. www.retezy-vam.com ŘETĚZY VAMBERK
PRESENTATION www.retezy-vam.com ŘETĚZY VAMBERK Where to find us? Dresden (D) - Zinnwald - Georgenfeld (D) E 55 Zinnwald (D) - Teplice (CZ) E 55 Teplice (CZ) - Praha (CZ) E 55 Praha (CZ) - Hradec Králové
More informationHVU with HAS/HAS-E rod adhesive anchor
HVU with HAS/HAS-E rod HVU with HAS/HAS-E rod adhesive anchor Mortar system Benefits Hilti HVU foil capsule HAS HAS-R HAS-HCR rod - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity
More informationInstallation & Operation Manual. Type 1801 External Seahorse Pantograph Wiper. without Control System
Wynn Marine Ltd Wynn House, Lansdown Estate, Cheltenham, GL51 8PL, United Kingdom Tel: +44 (0)1242 232266, Fax: +44 (0)1242 231131, Email: info@wynn.co.uk, website www.wynn.co.uk Installation & Operation
More informationElo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors
Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...
More informationReferences. DYWIDAG Tie Rods for Military Wharf in Guam
DYWIDAG Tie Rods References DYWIDAG Tie Rods for Military Wharf in Guam i Owner US Navy, Naval Base Guam, USA +++ General Contractor Black Construction Corporation, Guam, USA +++ Architect-Engineer Wilson
More informationSECO-CAPTO TOOLHOLDING FOR MAZAK MACHINES
SECO-CAPTO TOOLHOLDING FOR MAZAK MACHINES OUR EXTENSIVE RANGE Seco Tools are very pleased to launch its first Seco-Capto tool holding catalogue. We have worked in close partnership with Craftsman Tools
More informationHUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast Anchor version HUS-A 6 Screw with hex head HUS-H 6 Screw with hex head HUS-I 6 Screw with hex head Benefits - Quick and easy setting - Low
More informationDYWIDAG Prestressing Systems using Bars
DYWIDAG Prestressing Systems using Bars Contents ETA Approvals... 4 System description... 5 Prestressing Bars / Technical Data... 6 System overview... 7 Overview of anchorages... 8 Applications... 9 Overview
More informationDYWIDAG Threadbar Tie Rods
DYWIDAG Tie Rods DYWIDAG Threadbar Tie Rods Tie Rods produced from GEWI Steel and GEWI Plus threadbars can be used for a variety of marine applications. Construction of marine bulkheads for various docking
More informationLEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code
LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900
More information1000/14.02 KOBSERT. Thread inserts for metals
1000/14.02 KOBSERT Thread inserts for metals Contents KOBSERT Thread inserts for metals Page The principle 3 The benefits 3 Product types 3 Applications in the Automotive and General industry 4 Technical
More informationAccuracy counts! SENSORS WITH ANALOG OUTPUT
Accuracy counts! SENSORS WITH ANALOG OUTPUT OTHER APPLICATIONS: KEY ADVANTAGES: Distance measurement Positioning Profile detection Deformation monitoring Vibration monitoring Process monitoring Detection
More informationPRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE. By H P Gupta & D K Gupta
PRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE By H P Gupta & D K Gupta DIFFERENT TYPES OF DAMAGES 1.Minor cracks 0.5 to 5 mm wide in load or non-load bearing walls 2.Major
More informationSeismic Installation for Attic Storage System
Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener
More informationHUS-V Screw anchor. HUS-V Screw anchor. Basic loading data (for a single anchor) Mean ultimate resistance
HUS-V Screw anchor Anchor version HUS-V 8 / 10 Carbon steel concrete screw with hexagonal head Benefits - High productivity less drilling and fewer operations than with conventional anchors - Technical
More informationENDURO SERIES MAINTENANCE FREE CHAINS
E NDURO SE R IES MAINTE NANCE FR E E CHAINS E N D U R O M A I N T E N A N C E F R E E C H A I N S Regina ENDURO chains are designed to operate in lube-free applications. Designed to work without periodic
More informationFlamco Stainless steel mountings
S TA I N L E S S S T E E L M O U N T I N G S 9 Flamco Stainless steel mountings BRS-A BSF - SS RAIL R - SS GP - SS Edition 2007 / UK Stainless steel mountings Flamco offers the best attachment options
More informationFAG Hydraulic nuts. Technical Product Information
FAG Hydraulic nuts Technical Product Information Contents Application 2 Design 2 Design variants 3 Pressure generators, connectors 4 Dimension tables for FAG hydraulic nuts (metric) 6 Dimension tables
More informationValve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv)
Valve series MN-06 acc. to NAMUR, 3/2-way G1/4 750 Nl/min (0.762 Cv) Order code Series and function 1) Plug socket see page 5.042. MN-06-310-HN-442 Standard coil 1) 441 = 12 V DC, 4.2 W 442 = 24 V DC,
More informationSecurely Fastened Function Guaranteed
Securely Fastened Function Guaranteed Tube Clamps with a System Tube Clamps pursuant to DIN 3015, Part 1 The lightweight construction clamps can be used in a very wide range of applications in fluid technology.
More informationEuropean Technical Approval ETA-04/0013
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC
More informationDIRECT PUSH DRILLING.
DIRECT PUSH DRILLING. CONCEPT. Direct Push Drilling is a method of drilling and sampling where the tools are pushed or driven into the ground. No rotation is involved so all the samples are uncontaminated
More informationConnection Solutions
Connection Solutions DESIGN BUILD SYSTEM Connection Solutions for Cold formed Steel Construction Complies with; AS/NZS 4600:2005 AISI S100:2007 AS/NZ 1397 ASTM A653 DESIGN & BUILD SYSTEM FRAMECAD Construction
More informationDiameter. Swift Lift Round Recess Plug. Note: The diameter of the narrow recess plug is the same as the diameter of the round recess plug.
P-5 The P-5 is hot forged from carbon steel. The formed head provis spherical seating that the Lifting Eye engages, while a disc-shaped foot is embedd in the concrete. Due to its being a forged part, the
More informationHilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationVdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
More informationWERKZEUGMASCHINEN BENDING TOOLS
WRKZUGMASCHINN BNDING TOOLS Press Brakes HT Werkzeugmaschinen GmbH mmendinger Str. 21 D-79331 Teningen Germany Tel. + 49 (0) 76 41 46 09-0 Fax + 49 (0) 76 41 46 09-290 email: info@eht.de Internet: www.eht.de
More informationFLOORS REINFORCEMENT Shear Stud Connector for steel- concrete composite structures cold applied by pins
www.tecnaria.com FLOORS REINFORCEMENT Shear Stud Connector for steel concrete composite structures cold applied by pins HIGHPERFORMANCE FLOORS COMPOSITE STEEL AND CONCRETE STRUCTURES: STATIC AND ECONOMIC
More informationMountaineering and Climbing Equipment CONNECTORS / KARABINERS. Foreword
Mountaineering and Climbing Equipment CONNECTORS / KARABINERS UIAA 121 Foreword This UIAA Standard is only published in the English language version, which is the master text. For any validations in translation,
More informationOperating Instructions Drill rig DRU160
Operating Instructions Drill rig DRU160 Index 000 / 001 Original operating instructions 10988825 en / 20.10.2009 Congratulations! With a Hydrostress unit from TYROLIT you have chosen a tried and tested
More informationSubmittal Information
Wedge SPECIFIED FOR ANCHORAGE INTO CONCRETE Wedge anchs feature a stainless steel expansion clip, threaded stud body, nut and washer. Anch bodies are made of plated carbon steel, hot-dipped galvanized
More informationContact details HYPOXI DISTRIBUTORS
AUSTRALIA & NEW ZEALAND HYPOXI Australia 7 Blackfriars Street Chippendale NSW 2008 Australia Tel. +61 2 9281 2033 Fax +61 2 9281 2038 Email: australia@hypoxi.com AUSTRIA Email: austria@hypoxi.com BALTIC
More informationCutting the World. Cutting tools. for rotary drum cutters
Cutting the World Cutting tools for rotary drum cutters Round attack picks, pick boxes, retaining clips for erkat rotary drum cutters and cutter wheels erkat rotary drum cutters work under extremely hard
More informationEnglish version. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 4162 2012 ICS: 49.030.20 English version Aerospace series Screws 100 countersunk normal head, offset cruciform recess, coarse tolerance normal shank,
More informationIntegrated Manhole Ladder System
Application: This innovative product has been designed to provide safe access and egress to precast concrete manholes and inspection chambers. It can also be used within any other underground concrete
More informationElectrically operated valves Series M-05, 3/2-, 5/2- and 5/3-way G1/8 650 and 750 Nl/min (0.661 and 0.762 Cv)
Electrically operated valves Series M-05, 3/2-, 5/2- and 5/3-way G1/8 650 and 750 Nl/min (0.661 and 0.762 Cv) Order code Series and function M-05-310-HN-442 Standard coil HN at ports 2 + 4 HN at ports
More informationMetal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
More informationMETALWORKING PRODUCTS. Deep hole drilling Product catalogue and application guide
METALWORKING PRODUCTS Deep hole drilling Product catalogue and application guide AB Sandvik Coromant Not only a tool supplier Sandvik Coromant is the No.1 supplier of cutting tools for the metalworking
More informationHEAVY FORMING AND CONSTRUCTION. Products of skill and workmanship EEW PICKHAN
HEAVY FORMING AND CONSTRUCTION Products of skill and workmanship EEW PICKHAN EEW Group possesses the following approvals: ISO 9001 API 5L API 5LC API 5LD API 2B ASME U STAMP ASME U2 STAMP ASME S STAMP
More informationEuropean Technical Assessment ETA-10/0153 of 10/06/2015
ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet ww.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011 of
More informationBoston Scientific Spinal Cord Stimulation (SCS) Systems
Boston Scientific Spinal Cord Stimulation (SCS) Systems 91005942-03 REV B Boston Scientific Spinal Cord Stimulator Systems - Guarantees Boston Scientific Corporation reserves the right to modify, without
More informationHUS-HR Stainless steel Concrete Screw A4 316. CE conformity. Corrosion resistance. European Technical Approval
HUS-HR screw anchor Anchor version Benefits HUS-HR Stainless steel Concrete Screw Quick and easy setting Low expansion forces in base materials Through fastening Removable Forged-on washer and hexagon
More informationGlass Fibers Reinforced Composits (GFRP) for TUNNELLING
Glass Fibers Reinforced Composits (GFRP) for TUNNELLING Introduction The main utilization of GFRP Composites is extended to the entire field of temporary consolidation. The success of this application,
More informationStrengthening of Large Storage Tank Foundation Walls in an Aggressive Environment by External Post-tensioning. May 7th 2013: Dominique Deschamps
Strengthening of Large Storage Tank Foundation Walls in an Aggressive Environment by External Post-tensioning May 7th 2013: Dominique Deschamps Scope of the paper Presentation of the project Cause of cracks
More informationBonded Anchors & Mechanical Anchors
Bonded Anchors & Mechanical Anchors 1980 s and R-HPT mechanical anchors 2007 1887-1897 RAWLINGS BROTHERS started out in London 1912 RAWLPLUG Trademark registration 1919 Rawlings Brothers THE RAWLPLUG COMPANY
More informationInstallation information. METTLER TOLEDO MultiRange DW150 / DW150T wall scale
Installation information METTLER TOLEDO MultiRange DW150 / DW150T wall scale DW150 / DW150T wall scale Contents Contents Page 1. Installation... 2 1.1 Preparatory work... 2 1.2 Installing the wall plates
More informationLinear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors
20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical
More informationMONDOATHENS BASKETBALL SET (Reference PK110)
MONDOATHENS BASKETBALL SET (Reference PK110) DESCRIPTION The MONDOATHENS backstop unit is mainly designed for multi-sports pavilions and installations where the highest-level basketball competitions are
More informationEEC 94/20/EC APPROVED KINGPINS
EEC 94/20/EC APPROVED KINGPINS All Capus EEC approved Kingpin Assemblies have been tested in Germany by RWTuV. The tests include a simulated life test - 2 million cycles at the approved 'D' value loadings.
More informationHUS-HR, CR Screw anchor, stainless steel
HUS-HR, CR Screw anchor, Anchor version HUS-HR 6 / 8 / 10 / 14 Stainless steel concrete Screw with hexagonal head HUS-CR 10 Stainless steel concrete screw with countersunk head Benefits - High productivity
More informationSchöck Isokorb type KST User Selection Guide. Schöck Isokorb type KST Blindtext
Blindtext Schöck Isokorb type KST User Selection Guide Schöck Ltd 2-4 High Street Kidlington, Oxfordshire OX5 2DH Tel: 01865 290 890 Fax: 01865 290 899 E-mail: design@schoeck.co.uk Web: www.schoeck.co.uk
More informationTurning centers. Mill Turn Lathes. With the most powerful control in industry: SingleMax
Turning centers Mill Turn Lathes With the most powerful control in industry: SingleMax TMi General purpose- and heavy duty-lathes > TM 6 i > TM 8 i > TM 10 i > TM i > TM 18 i > TM 18 Li Benefits of the
More informationNew construction Repairing failed or old foundations Retrofit foundations Permanent battered piers Machinery/equipment foundations
from New construction foundations don t have to be a headache. The CHANCE Helical Pier Foundation System gives you the performance of concrete without the drawbacks and liabilities of driven piles and
More informationAuxiliary Rams USERS MANUAL
Auxiliary Rams 2007 Chief Automotive Technologies, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies, Inc. warrants for one
More informationRAMAX S Prehardened stainless holder steel
T O O L S T E E L F A C T S RAMAX S Prehardened stainless holder steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is intended to provide
More informationSR Door co-ordinators
SR Door co-ordinators DORMA SR 390 DORMA SR 392 Door co-ordinators DORMA SR 390 door co-ordinator, surface-installed 40 70 Active leaf (2nd closing) The DORMA SR 390 is a thoroughly proven, purely mechanical
More informationSITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents
English translation of German original Technical Information TI-P11 SITEMA PowerStroke Mould Closing Devices series FS drive system for powerful forces on a short stroke hydraulic actuation closing force
More informationEmbedded Parts Introduction - Anchors
In the plant construction or process plants such as chemical, petrochemical, gas or power plants various disciplines are brought into contact and built on each other. Civil, mechanical, electro technical
More informationLED WATERPROOF TUBE LIGHT SPECIFICATION
LED WATERPROOF TUBE LIGHT SPECIFICATION LED WATERPROOF T8 TUBE LIGHT 1. Product Description LED waterproof tube lights, with IP65 rating, can protect the tubes from dust, water and corrosion. Thus it can
More informationModular and Flexible. We want to make it easier for you! Innovative Riveting System. with blind rivet adapter BR 20. with blind rivet adapter BR 50
Modular and Flexible Innovative Riveting System 800 bar with blind rivet adapter BR 20 We want to make it easier for you! with blind rivet adapter BR 50 Engineered and Designed by with blind rivet nut
More informationWorld Consumer Income and Expenditure Patterns
World Consumer Income and Expenditure Patterns 2014 14th edi tion Euromonitor International Ltd. 60-61 Britton Street, EC1M 5UX TableTypeID: 30010; ITtableID: 22914 Income Algeria Income Algeria Income
More informationSDS PLUS 4 Claw (4 Cutting Edges) SDS-Plus
MASONRY DRILL BITS SDS-Plus Rotary Hammer with SDS chuck or SDS adapter 5/32"x6" to 1"x10" SDS-Plus Masonry Drill s are designed for use in a rotary hammer equipped with an SDS (slotted drive shaft) type
More informationStainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
More informationUltra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper
Ultra Live Center RN Type RN with morse taper NEIDLEIN ultra live centers are designed for employment in turning, grinding and other production machines. Owing to the application of bearing and the stable
More informationTZ WEDGE ANCHOR FOR CRACKED AND UNCRACKED CONCRETE
SECTION 2.2 PAGE 1 / 9 l DESCRIPTION UCAN TZ torque controlled mechanical expansion wedge anchors have a Category 1 classification. They are used to resist static, wind and seismic tension and shear loads
More informationMultiPost-AP anchorage device
MultiPost-AP anchorage device MultiPost anchorage point Type 1 Fixing on reinforced concrete with large, 360 rotating stainless steel lifting eye for the simultaneous securing of max. 2 persons. This can
More informationDYWI Inject Systems - Anchors and Rock Bolts
DYWI Inject Systems - Anchors and Rock Bolts 2 Contents Introduction... 3 DYWI Inject SILO 8044 Silicate Injection Resin for Anchors and Rock Bolts...4 Fields of Application... 4 Main Advantages... 4 System
More informationINTELLIGENT. belt CLEANING BELT CLEANING SOLUTIONS
INTELLIGENT belt CLEANING BELT CLEANING SOLUTIONS BELT CLEANING saves MONEY Carryback is the problem confronted by the material handling industry where product is transported by belt conveyors. working
More informationInstallation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
More informationTEPZZ 69 _ZA T EP 2 692 310 A2 (19) (11) EP 2 692 310 A2. (12) EUROPEAN PATENT APPLICATION published in accordance with Art.
(19) TEPZZ 69 _ZA T (11) EP 2 692 3 A2 (12) EUROPEAN PATENT APPLICATION published in accordance with Art. 13(4) EPC (43) Date of publication: 0.02.14 Bulletin 14/06 (21) Application number: 1276632.0 (22)
More informationSecurely Fastened Function Guaranteed
Securely Fastened Function Guaranteed Tube Clamps with a System Tube Clamps pursuant to DIN 3015, Part 1 The lightweight construction clamps can be used in a very wide range of applications in fluid technology.
More informationPay and Display Ticket Machines
VdS Guidelines for Physical Security Devices VdS 3546en Requirements, classification and test methods Draft This draft of guidelines have been agreed upon with the public and may be immediately used as
More informationpmpiping.com Sales Organisation Europe 23. July 2015 Page 1 of 11
Sales Organisation Europe Germany GmbH germany@ energy@ PM Renewables GmbH renewables@ PM Consulting GmbH consulting@ Azerbaijan GmbH Office Azerbaijan and Central Asia Heydar Aliyev Avenue 85/25 Baku,
More informationPC-Concrete Injectable Concrete Anchoring and Repair System
PC-Concrete Injectable Concrete Anchoring and Repair System DESCRIPTION: PC-Concrete is a two component (1:1 ratio), 100% solids, high modulus, structural epoxy paste. PC-Concrete is a solvent free, no
More informationRollers. from the UK s largest roller manufacturer. Quality Performance Reliability
Rollers from the UK s largest roller manufacturer Quality Performance Reliability 42 Index Gravity Rollers Light to Medium Duty 4 Heavy Duty 5 Plastic Rollers 6 Stainless Steel Rollers 7 Grooved Rollers
More informationDr. Jesús Gómez, P.E. 36th Annual Conference on Deep Foundations, Boston, MA
FHWA Hollow Bar Soil Nail (HBSN) Test Program Dr. Jesús Gómez, P.E. 36th Annual Conference on Deep Foundations, Boston, MA Outline Introduction and motivation Installation methods for testing Testing and
More informationfischer Test Report Fixing Tests for Wienerberger Porotherm blocks
fischer Test Report Fixing Tests for Wienerberger Porotherm blocks CONTENTS. Test Parameters... Substrates Tested Wienerberger Porotherm 90 &. Fixings Products Tested... Fischer Nylon UX Plug... Fischer
More informationPM 2 GRUNDFOS INSTRUCTIONS
PM GRUNDFOS INSTRUCTIS Max. m. (default) Max. t amb Min. 0 C P start =. bar (default) Max. 0 bar ( ) Min..9 bar (0.9 ) (default) bar Max. t liq Min. 0 C l / = max. 0 A 4 60 6 7 6. bar + 0.. bar + 0. =.
More informationEasy-action Door Closer DORMA TS 83
Easy-action Door Closer DORMA TS 83 DORMA TS 83 Easy-action Door Closer Easy-action door closer with thinking backcheck Easy to fix and even easier to adjust. The door closer for almost every door size
More informationEJOT Spiralform. The thread formers for metal. EJOT The Quality Connection
EJOT Spiralform The thread formers for metal EJOT The Quality Connection Imprint Editor: EJOT GmbH & Co. KG Industrial Fasteners Division D 57319 Bad Berleburg Layout and Realisation: EJOT GmbH & Co. KG
More informationVandal-proof keypad series
Model No. LBKP35900 / LBKP35900E (Encryption available) Interface: PS2, USB available. Dimensions: 100mm x 91.5mm No. of keys: 16 keys, high quality stainless steel G.W.: 0.75kg. All languages version
More informationHilti KWIK HUS-EZ I (KH-EZ I) Internally Threaded Carbon Steel Screw Anchor
Hilti KWIK HUS-EZ I (KH-EZ I) Internally Threaded Carbon Steel Screw Anchor Supplement to Hilti North American Product Technical Guide Volume 2: Anchor Fastening Technical Guide 2011 Edition 3.3. KWIK
More informationEuropean Technical Approval ETA-09/0169
UK CARES Pembroke House, 21 Pembroke Road, Sevenoaks, Kent, TN13 1XR, United Kingdom www.ukcares.com MEMBER OF EOTA European Technical Approval ETA-09/0169 Original version in English Trade name: Holder
More informationWorkholding systems. Magnetic clamping plates M-TECS SP 50 M-TECS SP 70
Workholding systems Magnetic clamping plates M-TECS SP 50 M-TECS SP 70 12/2010 M-TECS SP Magnetic clamping system M-TECS square poles for extremely heavy machining M-TECS square poles on a vertical machining
More informationProduct catalogue, abrasive cutting
Product catalogue, abrasive cutting Cutting nozzle assemblies Abrasive jet cutting system Abrasive hopper Abrasive material www.hammelmann.com Contents (Navigation via Bookmarks) Cutting nozzle assemblies
More informationOLI. Oil level indicator
OLI Oil level indicator Oil level indicator Unexpected or accidental oil leakages may occur randomly along transformer s lifetime. Clear indication of oil level inside transformer tank and on load tap
More informationThe KLINGERexpert 5.2.1
KLINGERexpert 5.2.1 Powerful Sealing Calculation The KLINGERexpert 5.2.1 gasket design program is a versatile piece of software to assist users in the selection of non-metallic gasket materials. KLINGER
More informationCable Trays Technical Instructions & Specifications
Cable Trays Technical Instructions & Specifications Products Catalogue Objective and Structure The company s main objective is the supply of quality products, with respect to: practical design increased
More informationLEVEL GAUGES WITH MAGNETIC JOINT L 14 - L 22 - L 34
LEVEL GAUGES WITH MAGNETIC JOINT L 14 - L 22 - L 34 2 LEVEL GAUGES WITH MAGNETIC JOINT SIZE Ø 140/220/340 58 58 TYPE LA TYPE LA 14 30 S 22 33 TYPE LA 22-34 NO. HOLES Ø D2 76 O-RING CENTRE OF THE CONSERVATOR
More informationMTA1 CAN, M1 10Prog CAN, AT1CAN, AT1 CoarseFine CAN, M1, AT1, AT1 CoarseFine, RA 12, RA 23, RA T1, FS 002 CAN, FS 002
GB MTA1 CAN, M1 10Prog CAN, AT1CAN, AT1 CoarseFine CAN, M1, AT1, AT1 CoarseFine, RA 12, RA 23, RA T1, FS 002 CAN, FS 002 Instruction manual 0459 576 101 GB 090129 Valid for serial no. 506 -xxx -xxxx, 719
More informationGLOBAL PRODUCT CATALOGUE. July 2009 DELTATOOLS. www.boartlongyear.com
GLOBAL PRODUCT CATALOGUE DELTATOOLS July 2009 www.boartlongyear.com TABLE OF CONTENTS ABOUT OUR PRODUCTS 4 manufacturing 7 CUSTOM SYSTEMS AND COMPONENTS 11 SAFETY 15 TABLE OF CONTENTS OVERBURDEN CASed
More informationHigh tensile strength stainless fasteners
High tensile strength stainless fasteners BUFAB STAINLESS HISTORY 1674 Svartå Bruk was founded 1912 Svartå Bruk was incorporated into the Hasselfors group. 1947 Production of Stainless Steel Fasteners
More information