PRO-VAC 150-LG-75 VACUUM BAGGING FILM For low temperature cure up to 120 C

PRO-VAC 150-LG-75 VACUUM BAGGING FILM For low temperature cure up to 120 C A tough, puncture resistant co-extrusion of polyolefin and nylon based resins which are designed for use in the production of polyester/ vinylester resin infused components for the wind energy, marine and general composite industries. Limited sensitivity to low humidity levels which are often problematic to predominantly nylon based films as the lack of moisture can reduce flexibility. This ensures consistent year long performance in all workshop environments. It is available in widths of up to 10 meters without seams. For larger more complex mouldings, such as boat decks, our 80 micron version is recommended due to its added resistance to handling stresses and improved burst resistance. Part number Colour Width PV150-LG-75 Light Green 4m, 6m, 8m & 10m Thickness 75μ +/-15% ISO 4593 Elongation (break) MD 340% +/- 15% ASTM D882 TD 350% +/-15% ASTM D882 Tensile (break) MD 30 N/mm² +/-15% ASTM D882 TD 25 N/mm² +/-15% ASTM D882 Maximum use temp 120 C Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer. This film contains a significant percentage of nylon which is hydrophobic therefore the film s characteristics may change dependent on workshop and storage environment. The lower the humidity, the stiffer the film will feel. Store in original packaging

PRO-VAC 150-LG-80 VACUUM BAGGING FILM For low temperature cure up to 120 C Modified structure to that of our standard product PRO-VAC 150, It has been designed for the moulding of very large, complicated structures such as boat decks, where the film can be subjected to significant handling and high stresses when vacuum is applied. Limited sensitivity to low humidity levels which are often problematic to predominantly nylon based films, as lack of moisture can reduce flexibility. This beneficial characteristic ensures consistent year long performance in all workshop environments. Available in both 12m and 16m wide without seams and can also be kitted into large formats by way of vacuum bag sealant tape. Part number Colour Width PV150-LG-80 Light Green 12m - 16m Thickness 80μ +/-15% ISO 4593 Elongation (break) MD 330% +/- 15% ASTM D882 TD 340% +/- 15% ASTM D882 Tensile (break) MD 33 N/mm² +/-15% ASTM D882 TD 25 N/mm² +/-15% ASTM D882 Maximum use temp 120 C Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer. This film contains a significant percentage of nylon which is hydrophobic therefore the film s characteristics may change dependant on workshop and storage environment. The lower the humidity, the stiffer the film will feel. Store in original packaging

PRO-VAC 100-LB-75 VACUUM BAGGING FILM For all commonly used resin systems A tough, high temperature resistant co extruded nylon based material, which is designed for use in the production of advanced composite structures such as wind turbine blades and nacelles, boat hulls and decks, plus other industrial structures. The film is ideal for use in both resin infusion and prepreg moulding applications and is resistant to all commonly used resin systems. Not suitable for use in autoclave processing of composites. The standard thickness is 75μ however other thicknesses are available to special order. Part number PV100-LB-75 Colour Light blue Width 3, 4, 6, 8 and 10.5 meters Thickness 75μ +/- 15% Elongation (break) MD 382% +/- 15% ASTM D882 TD 442% +/- 15% ASTM D882 Tensile (break) MD 54,4 N/mm² +/- 15% ASTM D882 TD 52,1 N/mm² +/- 15% ASTM D882 Maximum use temp 177 C Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer. This film contains a significant percentage of nylon which is hydrophobic therefore the film s characteristics may change dependant on workshop and storage environment. The lower the humidity, the stiffer the film will feel. Store in original packaging

PRO-VAC 200-O-50 & 200-G-75 VACUUM BAGGING FILM For oven and autoclave usage A highly flexible multilayer nylon vacuum bagging films designed for processing of advanced composite structures and laminated security glass. The film is ideal for use in both oven and autoclave cures, up to a maximum recommended temperature of 170 C Key benefits of this film are its high elongation and flexibility. Technical data (data is from 50μ thick film tests): Part number PV200-O-50 = 50μ thickness PV200-G-75 = 75μ thickness Colour Orange Width 1,5m and 2,2m in both 50 and 75 micron Available in tube and V sheet Thickness 50μ +/-15% - designation PRO-VAC 200-O-50 ISO 4593 75μ +/-15% - designation PRO-VAC 200-O-75 ISO 4593 Elongation (break) MD 410% +/-15% ASTM D882 TD 414% +/-15% ASTM D882 Tensile (break) MD 56 N/mm² +/-15% ASTM D882 TD 52 N/mm² +/-15% ASTM D882 Maximum use temp 170 C Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer. This film contains a significant percentage of nylon which is hydrophobic therefore the film s characteristics may change dependant on workshop and storage environment. The lower the humidity, the stiffer the film will feel. Store in original packaging

PRO-VAC 250-G-75GL VACUUM BAGGING FILM For Glass lamination / autoclave This film has been developed for use in the production of laminated security glass. A tough but flexible nylon film it is ideal for use in either oven or autoclave processing methods of glass structures incorporating EVA or PVB interlayer s. The standard thickness is 75μ however other thicknesses are available to special order. Part number Colour Width PV250-G-75GL Green 1,2m and 1,5m v-sheet Thickness 75μ +/-15% ISO 4593 Elongation (break) MD 374% +/-15% ASTM D882 TD 395% +/-15% ASTM D882 Tensile (break) MD 61,1 N/mm² +/-15% ASTM D882 TD 59,8 N/mm² +/-15% ASTM D882 Maximum use temp 170 C Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer. This film contains a significant percentage of nylon which is hydrophobic therefore the film s characteristics may change dependant on workshop and storage environment. The lower the humidity, the stiffer the film will feel. Store in original packaging

PRO-VAC N85 NYLON PEEL PLY An 85 g/m² heat set and scoured nylon 6,6 peel ply fabric Designed for hand lamination and the vacuum infusion process Has a red tracer as a visible indicator to reducing the possibility of any peel ply being left on the laminate The fabric leaves a finish that can aid in the sanding or grinding of the laminate We do not recommend this product to be used with Phenolic resins Part number Colour Width Length PVN85 Natural with red colour tracer 0-1520mm 100m/roll Area Weight 85 g/m² ±3% Maximum use temperature 180 C *please note that the maximum use temperature is process specific, therefore we recommend that tests are performed on the peel ply prior to use at elavated temperatures It is recommended that the peel ply are stored in a cool and dry environment. Recommended temperature range of storage is between 10 ~ 30 C and relative humidity between 50 ~ 75%. The peel ply should remain in the packaging until just prior to use.

PRO-VAC P85 POLYESTER PEEL PLY An 85g/m² heat set and scoured polyester peel ply fabric Designed for hand lamination and the vacuum infusion process Has a light red tracer as a visible indicator to reducing the possibility of any peel ply being left on the laminate The fabric leaves a finish that can aid in the sanding or grinding of the laminate This product can be used with Phenolic resins as well as all other standard resin systems but we do recommend that trails are conducted to evaluate compatibility Part number Colour Width Length PVP85 Natural with light red colour tracer 0-1520mm 100m / roll Area Weight (g/m2) 85 g/m² ±3% Maximum use temperature 180 C *please note that the maximum use temperature is process specific, therefore we recommend that tests are performed on the peel ply prior to use at elavated temperatures It is recommended that the peel ply are stored in a cool and dry environment. Recommended temperature range of storage is between 10 ~ 30 C and relative humidity between 50 ~ 75%. The peel ply should remain in the packaging until just prior to use.

PRO-VAC 500-B-28 Release Film For all commonly used resin systems Designed for use in resin infusion processing of advanced composite structures. It is compatible for use with a wide range of epoxy, polyester and vinylester resin systems however we recommend small scale trials prior to committing to large infusion mouldings. The films is available sky blue in colour with P31 (approx 6 holes per cm²) for vacuum infusion and standard P3 perforation pattern for wet bagging and pre pregs. The perforations are hot needled to ensure even resin saturation is achieved throughout the laminate. Other colours, thicknesses and perforation patterns may be possible dependant on volume requirements. Part number PV500-B-28 Density 0.97 g/cm³ ASTM D1505 / ISO/R 1183 Thickness 28 µ ISO 4593 Width 1500 nominal -0+2% mm Length 500 nominal -0+2% m Tensile strength at break 57,9± 10% N/mm² ASTM D882 Elongation at break 588± 10% % ASTM D882 Max use temperature 125 C ISO 306 Film is supplied in strong bubble plastic Store in original packaging.

PRO-VAC 550-Y-50 Release Films Release films instead of Peel ply. A mid temperature range, highly flexible polypropylene based release film. It is suitable for use with epoxy prepreg up to 150 C and may be used in resin infusion applications with a wide range of resin systems however we recommend small scale trials prior to committing to large infusion mouldings. The film is available yellow in colour with with P31 (approx 6 holes per cm²) for vacuum infusion and standard P3 Perforation pattern for hand lamination and pre preg. The perforations are hot needled to ensure even resin saturation is achieved throughout the laminate. Also available in 30 micron Part number PV550-Y-50 Density 0.89-0.91 g/cm³ ASTM D1505 / ISO/R 1183 Thickness 50 µ ISO 4593 Width 1500 nominal -0+2% mm Length 250 nominal -0+2% m Tensile strength at break 35± 10% N/mm² ASTM D882 Elongation at break 500± 10% % ASTM D882 Max use temperature 153 C ISO 306 Film is supplied in strong bubble plastic Store in original packaging.

PRO-VAC B1141 vacuum bagging sealant tape Low to medium temperature sealant tape Recommended for use in vacuum infusion, wet lay-up bagging and bag to bag (envelope bagging) processing. Compatible with most vacuum films and tool surfaces but pre-production trials are advisable. We recommend that the tape is removed at room temperature. Max use temperature colour Standard roll sizes PVB1141 Standard packaging PVB1141 150 C - bag to tool and bag to bag Black 3mm x 12mm x 15m 20 rolls per box - 36 boxes per pallet Store in original and unopened packaging and protected from humidity Store at a maximum temperature of 30 C in a ventilated environment Material has a 12 month shelf life from date of manufacture Store flat with a maximum of 4 boxes stacked

PRO-VAC 1G POLYESTER Pressure sensitive tape An economical pressure sensitive silicone adhesive polyester tape intented for general workshop use. Easily removed following oven or autoclave processing. Coloured green for easy identification on the mould Part number Widths Roll length PV1G 25mm and 50mm 66m Maximum use temp 180 C Film carrier Adhesive type Colour Total thickness Adhesion to steel Polyester Silicone Blue 62μ 400 cn/cm The tape can be stored for maximum 6 months from the date of production in dry conditions and in its original packaging. The material should be protected from extreme temperatures and direct sunlight. Once removed from its original packaging, the tape should be protected from dust and other impurities. Keep the rolls in horizontal position.

PRO-FIX SPRAY ADHESIVE Designed for bonding of dry glass, carbon and aramid fibers for composite structure preparation Can be also used for fixing core materials foams and balsa as well as vacuum consumables like peel ply and breather fabric PRO-FIX is only available in 500ml cans User guide Make sure the surfaces which are to be bonded are clean and dry, shake the can well and spray from a distance of 25 cm, hold the can vertically and spray an even layer of adhesive; it must not appear as being wet if it does then move further away from the surface. When spraying the adhesive keep a fluid movement with the hand to avoid spraying too much adhesive in one place After each application purge the nozzle by spraying the can upside down To achieving the optimum bond both surfaces must be sprayed with adhesive, wait around 1 minute to allow the solvent to evaporate then press the surfaces together Store in temperatures below 50 C and do not expose to direct sun light, flames or source of ignition Packaged in boxes of 12 cans and pallets of 50 boxes (600 cans) For more information please refer to the PRO-FIX MSDS and when handling products of this nature the user must always conform to their company s Health and Safety regulations and guidelines.

PRO-VAC BM230P FLOW MEDIA Extruded grid mesh Recommened for flat panels and single curvature moulds due to the stiffness of the material Compatiable with all standard epoxy, polyester and vinylester resin systems A faster flowing mesh compared to the standard knitted types Part number Colour PVBM230P Green Density 230 g/m² ±5% Nominal Temp Resistant 120 C Mesh Size Thickness 1.8 X 1.8mm 0.75 ~ 0.82mm Plastic film inside, 50M/Roll. It is recommended that the products are stored in a cool and dry environment. The mesh should remain in the packaging until just prior to use.

PRO-VAC KM160E1 FLOW MEDIA 3D Knitted mesh Compatiable with all standard epoxy, polyester and vinylester resin systems Highly drapable so can be used on complex moulds Can also be used as a reuasble breather for debulking at room temperature Available up to 2m wide Part number Colour Density PVKM160E1 Black 160 g/m²±5% Nominal Temp Resistant 120 C Thickness 1.0 mm Elongation At break 500% Tensile Strength 23 N/mm² Plastic film inside, 100M/Roll. It is recommended that the products are stored in a cool and dry environment. The mesh should remain in the packaging until just prior to use.

PRO-VAC B-150 BREATHER Medium weight non woven PET breather/bleeder Good drapability and works well with single curvature and complex parts Good for all low pressure production process and can be used in multiply layers to increase the flow capacity. Part number PVB-150 Mass per unit area 150 g/m² ISO 9073-1 Thickness at 2 kpa 1,8 mm ISO 9863-1 Tensile strength 225 / 290 N ISO 9073-3 Elongation at 100N 40 / 50 % ISO 9073-3 Melting point 250 C Maximum use temperature 210 C Standard roll length 95 m Standard roll width 1,52 m Composition 100% PET *rolls can be slit to specific widths upon request (minimum order will apply) Store in original packaging

PRO-VAC vacuum ancillaries A full range of interconnecting vacuum infusion hoses, valves, omega profiles and inlet block The PVINB-16 inlet block has been specially developed to not only to self seal with the PVL connectors but also to fit with the PVO omega profiles. To decrease the complexity of vacuum bagging and bridging around the inlet points. PRO-VAC INLET BLOCK Part number Material i/d (mm) height (mm) max temp PVINB-16 PP 16 +/- 0.5 35 100 C PRO-VAC L-CONNECTOR FOR INLET BLOCK Part number Material o/d max temp PVL-12 PE 12 100 C PVL-18 PE 18 100 C PRO-VAC OMEGA CHANNEL Part number Material I/d (mm) max temp length (m) PVO-16 PVC 16 60 C 4 PRO-VAC INFUSION VALVES Part number Material o/d max temp PVV-10 (double O-ring) PE 10 100 C PVV-12 (double O-ring) PE 12 100 C PVV-18 (double O-ring) PE 18 100 C

PRO-VAC T-INFUSION TAPS Part number Material o/d max temp PVT-10 PE 10 100 C PVT-12 PE 12 100 C PVT-18 PE 18 100 C PRO-VAC SPRIAL WRAP Part number Material I/d (mm) thickness (mm) max temp length (m) PVSW-10 PE 10 +/- 0.5 1.0 +/- 0.1 100 C 100 PVSW-12 PE 12+/- 0.5 1.0 +/- 0.1 100 C 100 PVSW-18 PE 18 +/- 0.5 1.5 +/- 0.1 100 C 100 PRO-VAC INFUSION HOSE Part number Material I/d (mm) thickness (mm) max temp length (m) PVI-10 PE 10 +/- 0.5 1.0 +/- 0.1 100 C 100 PVI-12 PE 12+/- 0.5 1.0 +/- 0.1 100 C 100 PRO-VAC REINFORCED HOSES Part number Material I/d (mm) thickness (mm) max temp length (m) PV-RHOSE-13 fabric reinforced PVC 13 5 60 C 100 PV-RHOSE-19 fabric reinforced PVC 19 5 60 C 50 PV-SRHOSE-18 PVC spiral reinforced PVC 18 2.5 60 C 50 Store in original packaging. All ancillaries are supplied in separate bags.

PRO-VAC HFVL High flow vacuum line PRO-VAC HFVL is acost effectivehigh quality micro porous vacuum line which allows air to flow consistently through itself as well as acting as a resin barrier throughout the vacuum infusion process. PRO-VAC HFVL consists of a combination of products that have been brought together to make a user friendly and easy hand able robust product. Adhesive was chosen as the sealing agent between the layers because during our extensive testing of the PRO-VAC HFVL we found that this method of sealing (instead of welding) produced a much higher quality and durable seal. Process benefits Allows for less complex infusion strategies therefore can reducelabour time Excellent vacuum compaction throughout the process resulting in a better quality laminate Small footprint on the laminate surface Releases easily from all know resin systems Can be used as a sacrificial vacuum line to initiate vacuum once the laminate is wet out Can be used as a single point vacuum outlet to combat troublesome dry areas in already established process Does not contain resin after cure therefore no issues with marking due to exotherm Reduced amount of resin required for the process because no resin is wasted in the vacuum lines and catch pots Specification Widths: 150mm and 300mm wide *Special widths may be ordered contact our technical staff for details Length: 100m long rolls Technical details and training For further technical information and training please contact our technical staff to organize a product demonstration. Store in original packaging at room temperature (22 C). Shelf life is 8 months

PRO-VAC MLR-5 Reinforced teflon mould release High quality self-adhesive Teflon coated glass mould release for composite processing applications Adheres to composite and metal tools as well as wooden moulds and plugs The adhesive system is pressure sensitive therefore is stable throughout vacuum and autoclave curing Recommended for use on flat or single curvature surfaces, can be joined using a butt joint Part number Reinforcement Coating PV MLR-5 woven glass PTFE Ptfe content 58% Adhesive Nominal adhesive weight Nominal adhesive thickness Nominal total thickness Adhesion Max use temperature Width Silicone 255 gsm 0,125mm 0,175mm 5,4 N/cm 260 deg c 1000mm Store in original packing at room temperature (22 C) Shelf life of 8 months from date of manufacture

PRO-VAC B1191 next generation vacuum bagging sealant tape Low to medium temperature sealant tape Improved level of tack and hand ability Tape preforms best at room temperature (+ 20 0 C), if the tape is too cold the tack levels will be dramatically reduced Recommended for use in vacuum infusion, wet lay-up bagging and bag to bag (envelope bagging) processing Compatible with most vacuum films and tool surfaces but pre-production trials are advisable We recommend that the tape is removed from the mould at room temperature Max use temperature Colour Standard roll size PRO-VAC B1191 Standard packaging PRO-VAC B1191 150 0 C - bag to tool and bag to bag Black 3mm x 12mm x 15m 22 rolls per box 50 boxes per pallet *The tape is also available in grey, as a double strip profile and a bead in various diameters Store in original and unopened packaging and protected from humidity Store at a maximum temperature of 30 C in a ventilated environment Material has a 12 month shelf life from date of manufacture Store flat with a maximum of 5 boxes stacked