SPRAY POLYURETHANE FOAM APPLICATOR INFORMATION PROGRAM PHOENIX, ARIZONA Insulation March 8-10 March 22-24 April 12-14 May 17-19 Roofing May 3-5
APPLICATOR INFORMATION PROGRAM OVERVIEW This SPFA accredited program for materials and equipment provides participants hands on opportunity to spray foam, learn spraying techniques and maintain spray foam equipment. Industry product changes occur in lightning speed. We understand that successful project completion depends on a combination of application experience, knowledge and certification. We have developed this program around guidance and hands on experience. This program and the presenters bring years of technical knowledge and experience to assist contractors with the vast technical challenges of polyurethane chemistry, equipment and application of materials. Bayer MaterialScience Applicator Information Program Prerequisites: 1. Completion on CPI Safety and Health on-line training at www.spraypolyurethane.org 2. Completion of Bayer MaterialScience Applicator Fundamental Program at www.spf.bayermaterialscience.com 3. Company must have a safety and respirator program that complies with OSHA requirements.
APPLICATOR INFORMATION PROGRAM AGENDA \ DAY ONE 8:00 AM WELCOME, INTRODUCTION, FACILITY SAFETY 8:30-9:00 REVIEW OF SPF HEALTH AND SAFETY/ APPLICATOR FUNDAMENTALS 9:00-9:15 BREAK 9:15-10:00 REVIEW OF SPF HEALTH AND SAFETY/ APPLICATOR FUNDAMENTALS (CONT.) 10:15-11:45 SPF SPRAY DEMONSTRATION 11:45-12:15 LUNCH (PROVIDED) 12:15-1:00 REVIEW SPRAY SAMPLES 1:15-1:45 EQUIPMENT PRESENTATION 1:45-2:00 BREAK 2:00-3:30 EQUIPMENT BREAKOUTS 3:30-3:45 BREAK 3:45-5:15 EQUIPMENT REVIEW DAY TWO 8:00-9:00 EQUIPMENT PRESENTATION 9:45-10:00 BREAK 10:00-11:30 EQUIPMENT BREAK OUT 11:30-12:00 LUNCH (PROVIDED) 12:00-2:00 SPRAY TIME 2:00-2:15 BREAK 2:15-3:30 SPRAY TIME 3:30-3:45 BREAK 3:35-5:15 SPRAY TIME COATINGS 6:30-8:30 GROUP DINNER
APPLICATOR INFORMATION PROGRAM AGENDA DAY THREE 8-8:30 REVIEW 8:30-9:30 BUILDING CODES, PRODUCT CERTIFICATION, COMPLAINTS, BAD FOAM EXAMPLES 9:30-9:45 BREAK 9:45-10:30 EQUIPMENT TROUBLESHOOTING 10:30-12:00 SPRAY TIME 12:00-12:30 LUNCH (PROVIDED) 12:30-2:30 SPRAY TIME 2:30-2:45 BREAK 2:45-3:15 REVIEW 3:15-4:45 WRITTEN TEST (MATERIAL & EQUIPMENT) 4:45-5:00 COURSE EVALUATION 5:00 DEPARTURE SEATING IS LIMITED TO 15 PARTICIPANTS PER SESSION. *MAY 3-5 WILL FOCUS ON ROOFING APPLICATIONS. ALL OTHER SESSIONS WILL FOCUS ON WALL APPLICATIONS.
APPLICATOR INFORMATION PROGRAM ENROLLMENT MARK THE DATE OF PROGRAM YOU WISH TO ATTEND: March 8-10 March 22-24 April 12-14 May 3-5* May 17-19 COMPANY: ADDRESS: CITY, STATE, ZIP TELEPHONE: FAX EMAIL: COMPANY INFORMATION NAME TITLE EXPERIENCE LEVEL (BEGINNER, INTERMEDIATE, ADVANCED) EQUIPMENT UTILIZED CPI SPF APPLICATOR ID # PARTICIPANT INFORMATION COST: $750.00 PER PERSON INCLUDES LUNCH DURING TRAINING AND DINNER ONE NIGHT METHOD OF PAYMENT (PAYABLE IN FULL UPON REGISTRATION) ** PAYMENTS CANNOT BE BILLED TO YOUR ACCOUNT** 1. PLEASE MAKE CHECK PAYABLE TO: BAYER MATERIALSCIENCE 2. CREDIT CARD NAME AS IT APPEARS ON CARD VISA/MASTERCARD# EXPIRATION DATE BAYER MATERIALSCIENCE 2400 SPRING STEUBNER RD SPRING TEXAS, 77389 FAX NUMBER: 281-288-3348 QUESTIONS? CONTACT: MARTHA.VANDAMME@BAYER.COM WWW.SPF.BAYERMATERIALSCIENCE.COM
To receive a discounted hotel room rate, please contact the Arizona Grand Resort and specify that you are with Bayer MaterialScience Group 8000 S. Arizona Grand Parkway Phoenix, Arizona 85044 Main Phone: 1 (866) 267-1321 Local Phone: (602) 438-9000 Fax: (602) 431-6535 www.arizonagrandresort.com *Please note: The resort's address changed in November 2007. The search engine mapping companies (Google, Yahoo, etc.) have not updated the resort address location and currently provide incorrect directions when using our new address. To ensure accuracy, please use this map and the instructions below for resort location. To obtain driving directions, please use 7777 S. Pointe Parkway, Phoenix, AZ 85044. We sincerely apologize for this inconvenience!
Directions to Arizona Grand Hotel From Sky Harbor Airport: Take the AZ-153 S towards 1-10/AZ-143. Turn SLIGHT LEFT onto EAST UNIVERSITY DR. Turn RIGHT onto AZ-143 S/HOHOKAM EXPWY. AZ-143 S turns into 48th ST. Take 48th St. to BASELINE RD. Turn LEFT onto BASELINE RD. Drive 2 blocks. Turn RIGHT onto S. Arizona Grand Parkway. From East Valley: Take US-60 W towards PHOENIX. Take the I-10 E exit on the left towards TUCSON. Keep RIGHT at the fork in the ramp. Turn RIGHT onto W BASELINE RD. Drive 1 block. Turn LEFT onto S. Arizona Grand Parkway. From Car Rental Station at Sky Harbor Airport: Exit the Car Rental Center and turn left onto Sky Harbor Circle South. Turn RIGHT onto Buckeye Road. Stay in the right lane and turn right onto the I-10 East Freeway. Stay on I-10 East until exit 155, Baseline Road. Turn RIGHT onto Baseline Road. Turn LEFT onto S. Arizona Grand Parkway Phoenix.
Directions to Bayer MaterialScience from Arizona Grand Resort Directions miles Start: Depart 8000 S Arizona Grand Pkwy, Phoenix, AZ 85044-5409 on S Pointe 0.2 Pkwy E (North) 1: At roundabout, take the FIRST exit onto S Pointe Pkwy 0.1 2: Turn RIGHT (East) onto W Baseline Rd 0.3 3: Turn LEFT (North) onto Local road(s) < 0.1 4: Keep STRAIGHT onto Ramp towards I-10 / US-60 / Phoenix 0.4 5: At exit 154, take Ramp (LEFT) onto I-10 [Maricopa Fay] towards I-10 / US-60 5.5 / Phoenix 6: At exit 150A, take Ramp (RIGHT) onto I-17 [US-60] towards I-17 / US-60 / I- 4.5 10-Truck W / Flagstaff 7: At exit 198, turn RIGHT onto Ramp towards Buckeye Rd 0.3 8: Road name changes to S Black Canyon Fay [S Black Canyon Hwy] 0.2 9: Turn LEFT (West) onto CR-85 [W Buckeye Rd] 0.6 10: Turn RIGHT (North) onto S 27th Ave 0.4 11: Turn LEFT (West) onto W Lincoln St 0.4 End: Arrive 3010 W Lincoln St, Phoenix, AZ 85009-5705
Disclaimer: The manner in which you use and the purpose to which you put and utilize our products, technical assistance and information (whether verbal, written or by way of production evaluations), including any suggested formulations and recommendations, are beyond our control. Therefore, it is imperative that you test our products, technical assistance and information to determine to your own satisfaction whether our products, technical assistance and information are suitable for your intended uses and applications. This application-specific analysis must at least include testing to determine suitability from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us. Unless we otherwise agree in writing, all products are sold strictly pursuant to the terms of our standard conditions of sale which are available upon request. All information and technical assistance is given without warranty or guarantee and is subject to change without notice. It is expressly understood and agreed that you assume and hereby expressly release us from all liability, in tort, contract or otherwise, incurred in connection with the use of our products, technical assistance, and information. Any statement or recommendation not contained herein is unauthorized and shall not bind us. Nothing herein shall be construed as a recommendation to use any product in conflict with any claim of any patent relative to any material or its use. No license is implied or in fact granted under the claims of any patent.