VoIP Application Note: Configure NEC UX5000 w/ Nuvox SIP Trunking Service P/N 0913229 Date: 8/12/09
Table of Contents: GOAL... 3 PREREQUISITES... 3 SIP TRUNKING INFORMATION PROVIDED BY NUVOX... 3 NEC UX5000:... 3 REFERENCES:... 3 INSTALLATION WORKSHEET... 4 WAN SIDE:... 4 LAN SIDE:... 4 PBX INFO:... 4 NOTES:... 4 NEC UX5000 SETUP... 5 BLADE CONFIGURATION... 5 CCPU NETWORK SETUP... 6 VOIPDB CONFIGURATION... 7 VOIPDB DSP RESOURCE SELECTION... 8 SIP SYSTEM INFORMATION SETUP... 9 TRUNK AVAILABILITY... 10 VOIPDB DSP BASIC SETUP... 11 VOIPDB DSP BASIC SETUP... 12 IP SYSTEM INTERCONNECTION SETUP... 13 INITIAL TESTING AND TROUBLESHOOTING... 14 INITIAL TEST PLANS:... 14 TROUBLESHOOTING GUIDE:... 14 NOTES:... 14-2 -
Configure a NEC PBX Goal Provide a reference to NEC Solutions Providers and customers for configuring a NEC UX5000 to connect to a Nuvox SIP Interconnect utilizing a static configuration. The different devices can be configured in various configurations depending on your VoIP solution. This document covers the standard supported configurations. Prerequisites SIP trunking information provided by Nuvox Primary, SIP proxy server IP address Numbering Plan, if applicable for Point-to-Point connection. Trunking DID(s): o The DID(s) are forwarded to the Public WAN IP address(s), DNS or DNS SRV records of the PBX. NEC UX5000: UX5000 CCPU F/W Version 2.50J or Higher VoIP Daughter Board SIP Trunking License Digital, IP, and TDM terminals References: NEC UX5000 Networking Manual NEC UX5000 Feature and Programming Manuals - 3 -
Installation Worksheet Use this form to aid in setting up your SIP Trunking service. WAN Side: Internet Access Type & Speed: WAN IP Address: WAN Subnet Mask: WAN Gateway IP Address: LAN Side: LAN IP of SIParator or EdgeMarc: LAN Subnet Mask: LAN IP Address of UX5000: VLAN ID: PBX Info: Model: Firmware Version: Number of SIP Trunk Licenses: Add-on Software Applications: Number of Users: Number of Concurrent Calls: Notes: - 4 -
NEC UX5000 Setup Follow the UX5000 Feature and Programming Manuals and/or Networking Manual for more detailed information on feature-specific settings. The following are PC Programming images taken from an active UX5000 while interfaced with Nortel SIP Service. This document will provide guidance for a Static SIP Trunk Configuration on the UX5000 communications server. The images which are provide should be used only as a guide. For network specific information consult your Network Administrator and Internet Telephony Service Provider. Blade Configuration Confirm the UX5000 prerequisites have been met, observe the blade configuration Central Processor is equipped with MEMDB and 32VOIPDB (the VOIPDB size will determine the number of SIP Trunks that may be supported. - 5 -
CCPU Network Setup Set the Subnet Mask Set IP address Set VOIPDB Configuration - 6 -
VOIPDB Configuration Configure the number of physical ports trunk type which will be set as SIP trunks - 7 -
VOIPDB DSP Resource Selection It is recommended practice to select Commonly used for both IP extensions and trunks This configuration should be applied to all SIP Trunks. - 8 -
SIP System Information Setup 10-28-01: This is the Domain name that the UX5000 resides in. 10-28-02: This is the Host Name of the UX5000 in the domain. 10-28-03: Leave set to UDP 10-28-04: User ID in the SIP Invite Setup message. It is also used for outbound caller ID information if no information is assigned in commands 21-17, 21-19, 15-16, 14-12, and 10-36. Bandwidth.com defaults to E.164 format if using this setup in a UX5000 you will need to ask that 10 digit dialling by set in the Bandwidth.com network. A call can not be completed across the span if there is no outbound CID info at all. The reason for this is: the from and display portion of the invite message would be blank and it would not know where the call originated from. 10-28-05: Leave this set to IP Address. - 9 -
Trunk Availability Enable SIP Trunk Availability Enable the number of SIP trunks that you support. - 10 -
VOIPDB DSP Basic Setup - 11 -
VOIPDB DSP Basic Setup - 12 -
IP System Interconnection Setup Set the IP address of the ITSP SIP server Enable SIP Interconnect per valid entry Set the leading digit/digits of the number you will be dialing. - 13 -
Initial Testing and Troubleshooting Initial Test Plans: If you run into an issue with any of these tests, consult the troubleshooting chart below: 1. Test an Outbound call to a Local Number. Check for Ringback, 2-way Audio, and Quality. 2. Test an Outbound call to a Long Distance Number. Check for Ringback, 2-way Audio, and Quality. 3. Test an Outbound call to an International Number. Check for Ringback, 2-way Audio, and Quality. 4. Test a Long Outbound call past 15 minutes. 5. Test multiple call concurrencies on Outbound calls. Set up multiple calls to PSTN. 6. Test an Outbound Call to Operator 0. 7. Test an Outbound Call to Directory Assistance 411. 8. Test a 911 Call. (PLEASE IDENTIFY TO THE OPERATOR THAT THIS IS A TEST!!!!!) 9. Test an Inbound call to an internal DID. Check for Ringback, 2-way Audio, and Quality. 10. Test an Inbound call to Auto-Attendant. Check DTMF and Audio Quality. 11. Test Transferring calls off-site. 12. Test an Outbound call to an Auto-Attendant and verify DTMF. Troubleshooting Guide: Issue Cause Remedy Router Configuration Check Router Configuration NEC Configuration Check NEC Configuration No Calls IN/Out Note WAN IP Address and Contact Unqualified IP Address Provider NEC Configuration Check NEC Configuration No Calls Out Note WAN IP Address and Contact Unqualified IP Address Provider NEC Configuration Check NEC Configuration No Calls In Note WAN IP Address and Contact Unqualified IP Address Provider One-Way Audio NEC Configuration Check NEC Configuration Echo Excessive Delay Check LAN and WAN for high latency Echo Cancellation Issue Check Echo settings and/or consult Nortel Internet Access Issues Call Internet Access Provider Call Dropping Extreme Latency on LAN Check Latency on LAN SIP issue Contact Provider Static or HUM on Phones Power issue Check power if using AC should not be issue in PoE Packet Loss or Latency on LAN Check LAN Missing Parts of Words Packet Loss or Latency on WAN Check with Internet Access Provider Jitter Buffer Configuration Check with NEC Notes: - 14 -