Edixeon S5 White Series Datasheet Edixeon Series Features : Various colors for choice Low voltage operation Instant light Long operating life Reflow process compatible Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 1
Table of Contents General Information...3 Absolute Maximum Ratings...4 Characteristics...4 Luminous Flux Characteristic...5 Mechanical Dimensions...6 Characteristic Curve...7 Product Packaging Information...9 Revision History...10 About Edison Opto...10 Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 2
General Information Introduction Edixeon S5 series emitters are one of the highest flux LEDs in the world by Edison Opto. Edixeon S5 Series emitters are designed to satisfy more and more Solid-State lighting High Power LED applications for brilliant world such as flash light, indoor and outdoor decoration light. Edixeon S5 Series emitters are designed by particular package for reflow process application. Unlike most fluorescent sources, Edixeon S5 Series contains no mercury and has more energy efficient than other incandescent light source. Ordering Code Format 2 E R1 xx xx xx 000 xxx X1 X2 X3 X4 X5 X6 X7 X8 X1 X2 X3 X4 X5 Type Component Series Wattage Color 2 Emitter E Edixeon R1 R1 Series 01 1W CW Cool White 03 3W NW Neutral White WW Warm White X6 X7 X8 Internal code PCB Board Serial Number 05-000 - - - 06 - Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 3
Absolute Maximum Ratings Parameter Symbol Value Units DC Forward Current [1] (1W) 350 I (3W) F 700 ma Peak Pulsed Current; (tp 100μs, Duty cycle=0.25) [2] (1W) 700 I (3W) pulse 1000 ma Reverse Voltage V R 5 V Drive Voltage V D 5 V LED Junction Temperature [3] T J 125 C Operating Temperature - -30 ~ +110 C Storage Temperature - -40 ~ +120 C ESD Sensitivity - 8,000 V Soldering Temperature - 260 C Manual Soldering Time at 260 C(Max.) - 5 Sec. Notes: 1. Proper current derating must be observed to maintain junction temperature below the maximum at all time. 2. tp: Pulse width time 3. Allowable reflow cycles are 3 times for each LED. Characteristics Parameter Symbol Value Units Viewing Angle 2Θ 1/2 130 Degree 1W : 3.4 Forward voltage (Typ.) V F 3W : 3.7 V Thermal resistance - 10 o C/W V F / T V F / T -2 mv/ C CCT λd Cool White: 5,000-10,000 Neutral White: 3,800-5,000 K Warm White: 2,670-3,800 CRI - Cool White: 70 Neutral White: 75 - Warm White: 80 JEDEC Moisture Sensitivity - Level 2a Floor Life Conditions: 30 C / 60% RH Soak Requirements(Standard) Time (hours): 120+1/-0 Conditions: 60 C / 60% RH - Notes: 1. Wavelengths are stated as peak wavelength. 2. Edison maintains a tolerance of ±0.5nm for dominant wavelength, ±2nm for peak wavelength and ±5% on CCT measurement. 3. Edison maintains a tolerance of 0.06V on forward voltage measurement. Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 4
Luminous Flux Characteristic Luminous Flux Characteristics at I F =350mA, T j =25 C. Color Wattage (W) 1 Group Min. Luminous Flux(lm) Max. Luminous Flux(lm) U3 100 110 V1 110 120 Forward Current (ma) Order Code 350 2ER101CW06000001 Cool White W1 160 180 3 W2 180 200 700 2ER103CW06000002 W3 200 220 U1 86.5 90 1 U2 90 100 350 2ER101NW05000001 Neutral White U3 100 110 U5 150 160 3 W1 160 180 700 2ER103NW05000001 W2 180 200 T2 70 80 1 T3 80 86.5 U1 86.5 90 350 2ER101WW05000001 Warm White U2 90 100 U4 140 150 3 U5 150 160 700 2ER103WW05000001 W1 160 180 Note: Flux is measured with an accuracy of ± 10%. Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 5
Mechanical Dimensions Emitter Type Dimension Lens Housing Lead Emitter Type Circuit Slug Edixeon S5 series dimensions and circuit Notes: 1. All dimensions are in mm. 2. Lambertian and side emitting series slug has polarity as anode. 3. It is important that the slug can t contact aluminum surface. It is strongly recommended that there should coat a uniform electrically isolated heat dissipation film on the aluminum surface. Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 6
Characteristic Curve Spectrum Radiation Diagram Normalized Intensity(%) Cool White EDEW-xLS5-xR EDEH-xLS5-xR Neutral White EDEX-xLS5-xR Warm White Cool White, Neutral White and Warm White color spectrum at T J =25 C Luminous Flux & Forward Current Normalized Intensity Wavelength(nm) Forward Voltage(V) Normalized Intensity(%) 100 80 60 40 20 0-100 -80- -60 60-40- -20 02 0 20 04 4006 6008 80 01 100 00 Emission angle Angle (Degree) Forward Voltage & Forward Current Forward Current & Luminous Intensity at T J =25 C CCT & Forward Current Forward Current(mA) Forward Current(mA) Forward Current & Forward Voltage at T J =25 C Forward Current(mA) Forward Current & CCT at T J =25 C for Cool White Forward Current(mA) Forward Current & CCT at T J =25 C for Neutral White Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 7
Luminous Flux & Junction Temperature Normalized Intensity Forward Current(mA) Junction Temperature ( o C) Forward Current & CCT at T J =25 C for Warm White CCT & Junction Temperature Junction temperature & lumens intensity for Cool White, Neutral White, Warm White Junction temperature & CCT Shift for Cool White Junction temperature & CCT Shift for Neutral White Junction Temperature ( o C) Junction Temperature ( o C) Junction Temperature ( o C) Junction temperature & CCT Shift for Warm White Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 8
Pa rt N o: E DE W- KL C8 -B 3 Group : UZ 1V 03 Co lor: Whit e Qu anti ty: 100 0 艾 笛 森 光 電 股 份 有 限 公 司 ED ISON OPTO CO PORA TION In spec ted by : A4 100000 05 Di rec tive C omplia nce Te l +86-2- 8227 6996 Fa x +8 6-2- 82 27-6 997 4F N o. 800 Chun g- Chen g., C hun g- Ho C ity Taip ei. Taiw an Product Packaging Information Tape and Reel Dimension (-) (+) Cover Tape Carrier Tape Leader Length 20 Pockets Edixeon Emitter Humidity Indicator 17" Reel Seal Label Moisture absorbent material Label Moisture proof bag 1000pcs LEDs inside RO HS 5 boxes in 1 carton 2 bags in 1 box Note : 445*410*415 (Tolerance : ±5mm) Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 9
Revision History Versions Description Release Date 1 Establish order code information 2013/01/03 About Edison Opto Edison Opto is a leading manufacturer of high power LED and a solution provider experienced in LDMS. LDMS is an integrated program derived from the four essential technologies in LED lighting applications- Thermal Management, Electrical Scheme, Mechanical Refinement, Optical Optimization, to provide customer with various LED components and modules. More Information about the company and our products can be found at Copyright 2013 Edison Opto. All rights reserved. No part of publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photo copy, recording or any other information storage and retrieval system, without prior permission in writing from the publisher. The information in this publication are subject to change without notice. For general assistance please contact: service@edison-opto.com.tw For technical assistance please contact: LED.Detective@edison-opto.com.tw Copyright 2013 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 10