Accessory Support, page 1 Connect Footstand, page 2 Secure the Phone with a Cable Lock, page 3 External Speakers and Microphone, page 4 Headsets, page 4 Accessory Support The following table lists the accessories that the Cisco Unified IP Phones 8961, 9951, and 9971 support. An indicates support for a particular phone model and a dash (-) indicates no support. Table 1: Accessory Support for the Cisco Unified IP Phone 8961, 9951, and 9971 Accessory Type Cisco Unified Cisco Cisco IP Phone Unified IP Unified IP 8961 Phone 9951 Phone 9971 Cisco Unified IP Color Key Expansion Module: See Cisco Unified IP Color Key Expansion Modules. Add-on module 1 Up to 2 Up to 3 Cisco Unified Video Camera: See Cisco Unified Video Camera Installation. Add-on module - Cisco Accessory Third-Party accessories Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0 1
Connect Footstand Accessory Type Cisco Unified IP Phone 8961 Cisco Unified IP Phone 9951 Cisco Unified IP Phone 9971 Headsets: See Headsets, on page 4. This section includes information about each headset type. Analog Analog Wideband Bluetooth - USB (wired or wireless) Microphone: See External Speakers and Microphone, on page 4. External PC - Speakers: See External Speakers and Microphone, on page 4. External PC - Connect Footstand If your phone is placed on a table or desk, connect the footstand to the back of the phone. 2 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0
Secure the Phone with a Cable Lock Insert the curved connectors into the lower slots. Lift the footstand until the connectors snap into the upper slots. Note Connecting and disconnecting the footstand may require a little more force than you expect. Secure the Phone with a Cable Lock You can secure your phone with a laptop cable lock up to 20 mm wide. Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0 3
External Speakers and Microphone Step 3 Step 4 Step 5 Step 6 Take the looped end of the cable lock and wrap it around the object to which you want to secure your phone. Pass the lock through the looped end of the cable. Unlock the cable lock. Press and hold the locking button to align the locking teeth. Insert the cable lock into the lock slot of your phone and release the locking button. Lock the cable lock. External Speakers and Microphone External speakers and microphones are plug-and-play accessories. You can connect an external PC-type microphone and powered speakers (with amplifier) on the Cisco Unified IP Phone 9951 or 9971 by using the line in/out jacks. Connecting an external microphone disables the internal microphone and connecting an external speaker disables the internal phone speaker. Note Using poor quality external audio devices, playing loudspeakers at very loud volumes, or placing the microphone very close to the loudspeaker may result in undesirable echo for other parties on your speakerphone calls. Headsets Although Cisco Systems performs internal testing of third-party headsets for use with Cisco IP Phones, Cisco does not certify nor support products from headset or handset vendors. The phone reduces some background noise that a headset microphone detects, but if you want to further reduce the background noise and improve the overall audio quality, use a noise cancelling headset. Cisco recommend the use of good quality external devices; for example, headsets that are screened against unwanted radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of headsets and their proximity to other devices, such as mobile (cell) phones and two-way radios, some audio noise or echo may still occur. Either the remote party or both the remote party and the Cisco IP Phone user may hear an audible hum or buzz. A range of outside sources can cause humming or buzzing sounds; for example, electric lights, electric motors, or large PC monitors. Note In some cases, use of a local power cube or power injector may reduce or eliminate hum. Environmental and hardware inconsistencies in the locations where Cisco IP Phones are deployed mean that no single headset solution is optimal for all environments. We recommend that customers test headsets in the intended environment to determine performance before making a purchasing decision and deploy on a large scale. 4 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0
Audio Quality Related Topics External Device Audio Quality Beyond physical, mechanical, and technical performance, the audio portion of a headset must sound good to the user and to the party on the far end. Sound quality is subjective, and Cisco cannot guarantee the performance of any headsets. However, a variety of headsets from leading headset manufacturers are reported to perform well with Cisco IP Phones. For additional information, see http://www.cisco.com/c/en/us/products/unified-communications/uc_endpoints_ accessories.html Analog Headsets Analog headsets are supported on the Cisco Unified IP Phone 8961, 9951, and 9971. However, the Cisco Unified IP Phone 8961, 9951, and 9971 cannot detect when an analog headset is plugged in. For this reason, the analog headset displays by default in the Accessories window on the phone screen. Displaying the analog headset as the default allows users to enable wideband for the analog headset. Enable Wideband on Analog Headsets Although analog headsets are supported on the phone, the phones cannot detect when an analog headset is plugged in. For this reason, by default, the analog headset displays in the Accessories window on the phone screen. Displaying the analog headset as the default allows users to enable wideband for the analog headset. The phone is unable to detect whether the headset supports the wideband codec, but the user can enable wideband on analog headsets by following these steps: On the Cisco IP Phone, press Applications. Step 3 Step 4 Select Accessories. Highlight the analog headset, then press Setup. Press On to turn on the wideband and press Off to turn off the wideband. Enable Wideband Codec on Analog Headsets Although analog headsets are supported on the phone, the phones cannot detect when an analog headset is plugged in. For this reason, by default, the analog headset displays in the Accessories window on the phone screen. Displaying the analog headset as the default allows users to enable wideband for the analog headset. Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0 5
Wired Headsets If the screen doesn't display On or Off softkey, follow these steps to ensure that the user can enable wideband codec on an analog headset: Step 3 Step 4 Step 5 In Cisco Unified Communications Manager Administration, choose Device > Phone. In the Find and List Phones window, enter the search criteria for the phone to which you want to add the analog headset, then click Find. Click on the Device Name that you want. The Phone Configuration window displays. On the Product Specific Configuration Layout portion of the Phone Configuration window, ensure that the Wideband Headset UI Control option is enabled. (This option is enabled by default.) In the Product Specific Configuration Layout portion of the Phone Configuration window, you can also set the Wideband Headset option. (This option is also enabled by default). Wired Headsets You can use the wired headset with all of the features on the Cisco IP Phone, including the Volume and Mute buttons. Use these buttons to adjust the earpiece volume and to mute the speech path from the headset microphone. Connect Wired Headset To connect a wired headset to the Cisco IP Phone, perform these steps: Plug the headset into the Headset port on the back of the phone. Press the Headset button on the phone to place and answer calls using the headset. Disable Wired Headset You can disable the headset by using Cisco Unified Communications Manager Administration. If you do so, you also disable the speakerphone. To disable the headset from Cisco Unified Communications Manager Administration, choose Device > Phone and locate the phone that you want to modify. In the Phone Configuration window (Product Specific Configuration layout portion), select the Disable Speakerphone and Headset check box. 6 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0
USB Headsets USB Headsets Wired and wireless USB headsets are supported. You can connect a USB headset (or the base station for a wireless headset) to either the back USB port (if your phone has this port) or to the side USB port. Enable USB Headset The Cisco Unified IP Phone 9951 and 9971 contains both a back USB port and a side USB port, while the Cisco Unified IP Phone 8961 contains only a side USB port. You must enable the applicable USB port (either the back USB port parameter or the side USB port parameter) in Cisco Unified Communications Manager Administration (in the Product Specific Configuration layout portion of the window). Also, for the Enable/Disable USB Classes parameter in Cisco Unified Communications Manager Administration, ensure that Audio Class is selected. Enable the USB headset in one of the following windows: Phone Configuration (Device > Phone). Enterprise Phone Configuration (System > Enterprise Phone Configuration). Common Phone Profile window (Device > Device Settings > Common Phone Profile). Check the corresponding Override Common Settings parameter in the configuration window. Disable USB Headset To disable the USB headset, disable the USB port (or disable the Audio Class parameter) that you enabled in Cisco Unified Communications Manager Administration. Also, you can select another type of headset in the Accessories window on the phone, thus disabling the previously enabled headset. Disable the USB headset in one of the following windows: Phone Configuration (Device > Phone). Enterprise Phone Configuration (System > Enterprise Phone Configuration). Common Phone Profile window (Device > Device Settings > Common Phone Profile). Check the corresponding Override Common Settings parameter in the configuration window. Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0 7
Wireless Headsets Wireless Headsets You can use a wireless headset with the Cisco Unified IP Phone. The Cisco website provides information about wireless headsets that work with your IP phone. Go to the following URL: http://www.cisco.com/en/us/partner/prod/voicesw/ucphone_headsets.html See the wireless headset documentation for information about connecting the headset and using the features. Bluetooth Wireless Headsets The Cisco Unified IP Phones 9951 and 9971 support Bluetooth wireless headsets. Bluetooth enables low-bandwidth wireless connections within a range of 30 feet (10 meters). The best performance is in the 3- to 6-foot (1- to 2-meter) range. Bluetooth wireless technology operates in the 2.4 GHz band, which is the same as the 802.11b/g band. Interference issues can occur. Cisco recommends that you: Use 802.11a that operates in the 5 GHz band. Reduce the proximity of other 802.11b/g devices, Bluetooth devices, microwave ovens, and large metal objects. The Cisco Unified IP Phone uses a shared key authentication and encryption method to connect with headsets. The Cisco Unified IP Phone can connect with up to five headsets at a time. The last connected headset is used as the default. Pairing is typically performed once for each headset. After a device is paired, the Bluetooth connection is maintained as long as both devices (phone and headset) are enabled and within range of each other. The connection typically reestablishes itself automatically if either of the devices powers down then powers up. However, some headsets require user action to reestablish the connection. The Bluetooth icon indicates whether a device is connected. Potential interference issues can occur. Cisco recommends that you reduce the proximity of other 802.11b/g devices, Bluetooth devices, microwave ovens, and large metal objects. If possible, configure other 802.11 devices to use the 802.11a channels. For a Bluetooth wireless headset to work, it does not need to be within direct line-of-sight of the phone, but some barriers, such as walls or doors, and interference from other electronic devices, can affect the connection. When headsets are more than 30 feet (10 meters) away from the Cisco Unified IP Phone, Bluetooth drops the connection after a 15- to 20-second timeout. If the paired headset comes back into range of the Cisco Unified IP Phone and the phone is not connected to another Bluetooth headset, the in-range Bluetooth headset automatically reconnects. For certain phone types that operate in power-save modes, the user can wake up the headset by tapping on the operational button to initiate the reconnect. You must enable the headset and then add it as a phone accessory. The phone supports various Handsfree Profile features that enable you to use hands-free devices (such as Bluetooth wireless headsets) to perform certain tasks without having to handle the phone. For example, instead 8 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0
Bluetooth Wireless Headsets of pressing Redial on the phone, users can redial a number from their Bluetooth wireless headset by following instructions from the headset manufacturer. These hands-free features apply to Bluetooth wireless headsets that are used with the Cisco Unified IP Phone 9951 and 9971: Answer a call End a call Change the headset volume for a call Redial Caller ID Reject Divert Hold and Accept Release and Accept Hands-free devices may differ as to how features are activated. Device manufacturers may also use different terms when referring to the same feature. Important Only one headset type works at any given time, so if you use both a Bluetooth headset and an analog headset that are attached to the phone, enabling the Bluetooth headset disables the analog headset. To enable the analog headset, disable the Bluetooth headset. Plugging a USB headset into a phone that has Bluetooth headset enabled disables both the Bluetooth and analog headset. If you unplug the USB headset, you can either enable the Bluetooth headset or disable the Bluetooth headset to use the analog headset. For information about how to use your Bluetooth wireless headset, see: Cisco Unified IP Phone 8961, 9951, and 9971 User Guide for Cisco Unified Communications Manager (SIP) User guides provided with your headset Enable Bluetooth Wireless Headset Before users can use a Bluetooth Wireless headset, you must enable it. Step 3 Step 4 In Cisco Unified Communications Manager Administration, choose Device > Phone. Locate the phone you want to modify, and go to the Phone Configuration window for that phone. In the Phone Configuration window, select Enable for the Bluetooth setting and Handsfree for the Bluetooth Profiles setting. Save your changes. Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0 9
Bluetooth Wireless Headsets Remove a Bluetooth Device from the Phone When you want to remove a Bluetooth device, you delete it from the Accessories menu. Press Applications. Step 3 Select Accessories. Highlight the device that you want to remove and press Delete. 10 Cisco Unified IP Phone 8961, 9951, and 9971 Administration Guide for Cisco Unified Communications Manager 10.0