Instruction manual art. 01547 Installation manual
Contents
GENERAL FEATURES from page 5 FUNCTIONALITY from page 6 FUNCTIONALITY GENERAL FEATURES
For all the details about the Well-contact Plus system, refer to the installer manual that can be downloaded from the Software Product Software Well-contact Plus section on the website www.vimar.com. 4
General features KNX IP Interface, installation on DIN rail (60715 TH35), occupies 2 modules size 17.5 mm. The IP/KNX interface 01547 is capable of converting KNX telegrams into IP telegrams over Ethernet. The data can then be exchanged between the KNX system and the IP network. Characteristics Supply voltage: - BUS: 30 V d.c. SELV - Additional: 12-30 V d.c., 12-24 V ~ Power draw: - over BUS: 5 ma - additional power supply: 190 ma Dissipated power: 0.8 W Terminals: - TP Bus - Additional power supply - IP 10/100 BaseT RJ45 connector, IEEE 802.3 Operating temperature: -5 C - + 45 C (inside). IP20 protection rating 2 modules of 17.5 mm. GENERAL FEATURES Connections The connection to the bus and to the applications is made directly from the terminals on the front of the interface 01547. FRONT VIEW AND TERMINALS A: Bus State IP LED B: Traffic IP LED A B 01547 KNX IP INTERFACE Bus State IP TP Traffic I H C: Additional power supply 12-30 V d.c., 12-24 V~ D: Configuration LED E: Configuration button F: KNX TP Bus G: Function button H: Traffic TP LED Function G I: Bus State TP LED 12-24V 12-30V KNX C D E F Operation The configuration of the device and its parameters takes place via the ETS software. To start configuring the device and assigning its physical address, press the configuration button; the LED will be on steady throughout the operation. LED indicators Bus State IP LED: - off = error on LAN line - on green = correct LAN line operation - on red = manual overwrite on Bus State TP LED: - off = error on BUS KNX or BUS off, - on green = correct BUS operation Traffic IP LED: - blinking green = data traffic on the LAN line - off = no data traffic on the LAN line - blinking red = transmission error on the LAN line Traffic TP LED: - blinking green = data traffic on the BUS line - off = no data traffic on the BUS line - blinking red = transmission error on the BUS line Configuration LED: on red during the configuration phase (physical address assignment) VIMAR group 5
Functionality 1. Description Following highlights are characterising IP interface: Support of long messages up to 250 byte. High internal amount of communication buffers capable smoothing peeks in communication load. UPnP available to discover the device in IP network. The ETS can discover the device as communication interface through KNXnet/IP Search Request. WEB interface: currently providing device settings and an opportunity to switch on to program mode. The firmware can be updated through the web interface. Wide power supply voltage. 1.1 Communication objects IP interface 01547 has no KNX communication objects. 1.2 Programming interface The IP interface 01547 can be used together with the ETS as a programming interface. The device provides an additional physical address for this purpose which can be used for a tunnelling connection. 1.3 Tunnelling The presence of the Internet Protocol (IP) has led to the definition of KNX and IP. The IP interface 01547 provides the means for point-to-point connections KNX and IP system between a supervisory system and a KNX installation. 2. Rated voltage/rated current Supply (V) Current typ (ma) Power (W) 11 45 0,495 15 33 0,495 20 25,3 0,506 24 21,6 0,5184 31 18 0,558 3. State of delivery Every IP interface 01547 is delivered with these default parameters. Physical address 15.15.255 Physical address for tunnelling connections 15.15.255 IP address IP address assignment DHCP From DHCP service IP routing multicast address 224.0.23.12 IP subnet mask IP standard gateway DHCP DHCP 6
Functionality 4. ETS Parameters 4.1 Properties 4.1.1 General FUNCTIONALITY 4.1.1.1 General parameter ETS-Text Nome Host Range [Default value] ZYXW [KNX IP Interface] Comment Field to enter the IP Interface name (30 signs max.). For an easy search of the device with the ETS or with a KNXnet/IP visualisation system. 4.2 IP Configuration 4.2.1 DHCP configuration ETS-Text DHCP Range [Default value] use do not use [use] Comment If DHCP is used, no parameterisation needed. If DHCP is not used, following parameters are to be set. VIMAR group 7
Functionality 4.2.1 DHCP manual configuration ETS-Text DHCP configuration [Byte1]. [Byte2]. [Byte3]. [Byte4]. IP Address IP Byte 1 IP Byte 2 IP Byte 3 IP Byte 4 Net mask NM Byte 1 NM Byte 2 NM Byte 3 NM Byte 4 Gateway GW Byte 1 GW Byte 2 GW Byte 3 GW Byte 4 Range [Default value] use do not use [use] Comment If DHCP is not used, following parameters are to be set. IP Byte 1 to 4: manual input. Net mask Byte 1 to 4: manual input. Gateway Byte 1 to 4: manual input. NOTE: The Multicast IP address 224.0.23.12 is the defined address for the IP interface from the KNX Association in conjunction with the IANA. 8
Functionality 5. WEB presentation Through the IP connection on port 8080 http you can communicate with the IP interface 01547 to display information or execute commands. 5.1 Device Info Through this screen displays the main characteristics of the device: addresses, hardware and software versions, status, etc. 5.2 Program The Program function allows, remotely, to bring the device in its programming phase for ETS; this function is useful to avoid pressing the configuration button (E) on the front of the IP interface. FUNCTIONALITY 5.3 Update Selecting Update you upgrade the software interface IP. To do this you must: bring the device in Program Mode by pressing the configuration button (E) or by using the Program procedure described in the previous paragraph; press the function button (G) and the software interface IP can then be updated. VIMAR group 9
Functionality At this point, the interface IP waits for 10 min updating software. Then select the file and update the software interface; the device enters at boot mode. 10
Functionality After the update the device returns to normal mode. FUNCTIONALITY VIMAR group 11
Viale Vicenza, 14-36063 Marostica VI - Italy Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 Fax (Export) +39 0424 488 709 www.vimar.com 01547 EN 01 1502 VIMAR - Marostica - Italy