Magna Wall Acrylic & Elastomeric Coatings (Textured) Product Overview, Instructions, & Data s t u c c o D 9
Magna Wall Acrylic & Elastomeric Coatings (Textured)
product Overview Magna Wall Acrylic and Elastomeric Coatings (textured) are based upon 100% acrylic polymers, providing outstanding service life at low temperatures and after exposure to the weather. Magna Wall Acrylic and Elastomeric Coatings resist mildew growth, rain stain, and dirt pickup, and are also highly chalk-resistant. Basic Use: Magna Wall Textured Coatings are recommended as a low-maintenance, weather-resistant exterior wall coating, providing design flexibility and a variety of creative colors for properly-prepared concrete walls, masonry, and stucco sub-surfaces. Advantages: Bridges hairline cracks Cleans with water Highly chalk-resistant Flexible at low temperature Maximum adhesion Mildew-resistant Non-toxic, water-based Water-resistant Wide color selection Coverage (Textured): May be applied by hand or machine, and floated to desired texture. Approximately 125 to 140 sq. ft. per five-gallon pail (depending on texture). Packaging: Five-gallon pail. Weight depends on level of pigment added to obtain desired color. Approximate weight 60 lbs. per pail. Textures: Magna Wall Coatings are offered in three different textures: sand finish, medium finish, and rough finish. p. 2
Magna Wall Acrylic & Elastomeric Coatings (Textured)
product instructions Drying Time Will dry to touch in 3 to 4 hours at 70 F. Protect from rainfall for 24 hours at 70 F. More time required when temperature is cooler and/or when relative humidity is higher. Keep product from freezing for 48 hours after application. Application Procedure Previously-coated surfaces All previously-coated surfaces must be pressure-cleaned to remove all dirt, dust, chalk, mildew, algae, foreign materials, etc. A cementitious primer/basecoat must then be applied over entire substrate. If cracking is present, a fiberglass mesh should be embedded into the primer/ basecoat for added strength. Ensure the area to be coated is in sound condition. A pull-off test may be neces- sary to ensure the area to be covered is bonded securely to the substrate. New Masonry/Poured Concrete Walls Remove all dirt, oil, grease, mortar, and any other compounds that may inhibit a strong bond. A cementitious primer/basecoat may be needed to skim substrate. Concrete or mortar must be thoroughly cured for a period of at least 30 days at 75 F or a QuickCure primer may be used. Stucco Surfaces Remove all dirt, oil, grease, mortar, and any other compounds that may inhibit a strong bond. Stucco surfaces should be cured for 30 days at 75 F or a QuickCure primer may be used, or the ph of the stucco must be 9.0 or lower. p. 4
Magna Wall Acrylic & Elastomeric Coatings (Textured)
Application/Mixing All surfaces to be covered must be clean, cured, and dry. Mix Magna Wall Coatings with a 1/2 drill and paddle until a workable consistency is attained. Mix can be diluted by adding up to 16 oz. clean water. Magna Wall Textured Coating can be applied with a stainless steel trowel or spray equipment using a plastic float to achieve desired texture. Clean Up Use soapy water immediately, while Magna Wall Acrylic & Elastomeric Coatings are still wet. Shelf Life An unopened container stored in a cool, dry location should last two years. Cautions And Limitations Dark colors may fade. Avoid freezing product while in storage, or during curing time. Not for waterproofing below grade. Not for use on submerged surfaces. Not intended to be used as a waterproof coating. In-service temperature limit is 200 F. Magna Wall Coatings must not be used on exposed exterior horizontal surfaces. Minimum slope is 27 and maximum width is 12. Not for use with EIFS. MSDS should be viewed in order to understand all warnings. Warranty This Magna Wall product comes with a one (1) year Limited Warranty for replacement of defective materials. Contact Magna Wall for full details or to inquire about longer coverage periods. Technical And Field Services Available on request. p. 6
Premium Stuccos, Mortars, & Masonry Cements 5014 Callaghan Road San Antonio, TX 78228 P: 210.680.3441 www.magnawall.com For a Magna Wall Distributor Near You, Please Call: TF: 800.881.6297 F: 210.680.3449 For Technical Questions Concerning Magna Wall, Please Call: TF: 800.626.4391 F: 210.682.2020 All specifications subject to change without notice. Printed in the USA All rights reser ved. Copyright 2005