Alsident System 50 Antistatic (AS) Product Information
System 50 Antistatic General Information Product Specification Product description System 50 Antistatic Alsident System Airflow between 45 85 m 3 /h. System 50 Antistatic is particularly suitable in non-aggressive areas and where static electricity must be avoided eg electronics industries and technical schools. The standard Alsident System 50 Antistatic extraction arms are available in various types that are complementary to each other with reaches up to 1,380 mm. The System 50 extraction arms are quickly mounted with standard brackets for table, wall or ceiling. In combination with the wide range of hood designs it is possible to choose an extraction arm adapted for almost any work situation. Alsident System 50 Antistatic extraction arms are self-sustaining with an internal bearing spring, TCP-chromated aluminium tubes and joints of Polypropylene with a diameter of 50 mm. All internal components are made of acid-proof stainless steel (AISI 316L). The TCP-chromated surface is corrosion protected and conductive. The TCP-chromation does not contain Chrome (VI). The construction constitutes a very user-friendly extraction arm which is easy to adjust to the source of the pollutant during the working process. Alsident System 50 Antistatic is approved for use in ESD-areas according to IEC 61340-5-1 and is therefore delivered with an earthing wire with a 1MΩ resistance. Further information is available in Mounting on the extraction arm or under Technical Support on our website. An extraction arm from Alsident System consists of three parts: An extraction arm, a hood and a mounting bracket. Each part must be ordered separately. In addition to the standard range, Alsident System offers special customized solutions. The Alsident technical department is always ready to help you find the best solution. Alsident offers short delivery time for both standard products and special solutions. GI 01
System 50 Antistatic General Information Product Specification Technical Specifications Recommended Airflow: Normal: 65 m 3 /h Air Temperature: Key to the Signatures SYSTEM NO. 50 VERSION Minimum: 45 m 3 /h Maximum: 85 m 3 /h -15 C +90 C Material: Pipes: Chromated Aluminium (TCP) Joint: O-Ring: Flange: Damper: Thumbscrew: CHAPTER AS Antistatic GI Conductive Polypropylene (PP) Conductive Polyethylene (PE) Conductive Polypropylene (PP) Polyethylene (PE) Polypropylene (PP) yellow Threaded Stay: Acid-proof stainless steel (AISI 316L) Spring: Acid-proof stainless steel (AISI 316L) The antistatic version of System 50 is produced according to IEC 61340-5-1. The extraction arm includes an earthing wire with a 1MΩ resistance. Abbr.: TCP: Trivalent Chromium Passivation RoHS compatible surface treatment for aluminium Technical Reports Technical Reports: PP: PE: Polypropylene Shatterproof and chemical resistant Polyethylene Local extraction for workplaces inclusive all material for mounting. All components RoHS-compatible according to the directive 2002/95/EF (RoHS). Capture Efficiency (Danish Technological Institute) ESD test report (DELTA) Download: www.alsident.com > Technical Support > Test Reports BM WCM General Information Table Mounted Wall/Ceiling Mounted PAGE NO. 01 GI 02
System 50 Antistatic General Information Products Overview Table mounted Table mounted (TM), 2-joint Diam. Table mounted (TM), 3-joint Diam. L B C 50-47-1-6 Weight approx. [kgs] 50-5747-1-6 Part No. 50 445 275 350 0.8 50-27-1-6 50 545 375 350 0.8 50-37-1-6 50 645 475 350 0.8 50-47-1-6 L A B C Weight approx. [kgs] Part No. 50 765 375 275 350 1.1 50-3727-1-6 50 945 475 375 350 1.3 50-4737-1-6 50 1125 575 475 350 1.4 50-5747-1-6 GI 03
System 50 Antistatic General Information Products Overview Wall and Ceiling mounted Wall/Ceiling mounted (WCM), 2-joint Diam. Diam. L B C 50-47-3-6 Weight approx. [kg] 50-5747-3-6 Part No. 50 530 375 350 0.8 50-37-3-6 50 630 475 350 0.9 50-47-3-6 Wall/Ceiling mounted (WCM), 3-joint L A B C Weight approx. [kg] Part No. 50 750 375 275 350 1.1 50-3727-3-6 50 910 475 375 350 1.3 50-4737-3-6 50 1080 575 475 350 1.4 50-5747-3-6 50 1380 875 475 350 1.6 50-8747-3-6 GI 04
System 50 Antistatic General Information Accessories Overview Suction Nozzle width 100 mm Part No.: 1-5010-6 Recommended for concentrated sources of pollution. Efficient as it gets close to the source without obstructing the work process. Often used in the electronics industry. Internal diffuser to increase efficiency. Material Hood: Chromated Aluminium (TCP) Flange: Conductive Polypropylene (PP) Connection tube: Chromated Aluminium (TCP) Suction Nozzle width 200 mm Part No.: 1-5020-6 Recommended for concentrated sources of pollution. Efficient as it gets close to the source without obstructing the work process. Often used in the electronics industry. Internal diffuser to increase efficiency. Material Hood: Chromated Aluminium (TCP) Flange: Conductive Polypropylene (PP) Connection tube: Chromated Aluminium (TCP) Suction pen Alu Part Nos.: 1-5021-6 and 1-5031-6 Recommended for small concentrated sources of pollution. Efficient as it gets close to the source without obstructing the work process. Carefully made funnel increases the extraction efficiency. Material Connection tube: Chromated Aluminium (TCP) Length Part No. 210 mm 1-5021-6 310 mm 1-5031-6 GI 05
System 50 Antistatic General Information Accessories Overview Metal Hood (Diam. 200 mm) Part No.: 1-5024-6 Recommended when extracting hot gases, fumes, light dust concentrations etc. Material Metal Hood: Flange: Connection tube 1 : 1) Separately enclosed at delivery Recommended for light fumes, gases and small open vessels. Increased stability due to reinforced rim of the hood. Increased efficiency at an angled position. Material Hood: Flange: Connection tube 1 : 1) Separately enclosed at delivery Conductive Polypropylene (PP) Conductive Polypropylene (PP) Chromated Aluminium (TCP) Recommended when extracting heavy gases and fumes. High efficiency when placed vertically on a surface e.g. a table. Practical rim for easy positioning of the hood. Gets close to the source without obstructing the work process. Material Hood: Conductive Polypropylene (PP) Flange: Conductive Polypropylene (PP) Connection tube 1 : Chromated Aluminium (TCP) 1) Separately enclosed at delivery Chromated Aluminium (TCP) Conductive Polypropylene (PP) Chromated Aluminium (TCP) Dome Hood (Diam. 385 mm) Part No.: 1-5035-6 Flat Hood (330 x 240 mm) Part No.: 1-503324-6 Protective Grill (for hoods) Part No.: 5-16-6 Protective Grill for mounting in hood. Prevents extraction of foreign materials. Material: Colour: Conductive Polypropylene (PP) Black GI 06
System 50 Antistatic General Information Accessories Overview Wall Bracket Part No.: 2-195-050 For wall mounting of System 50 extraction arms. Made of steel with a polyester powder coating in black on all surfaces. Other colours available on request. Three options available for the connection to the duct: 1) Directly from the top of the bracket to a Ø 80 mm spiro duct. 2) With reducer 4-10075 to a Ø 100 mm spiro duct (reducer included). 3) Directly from the top of the bracket to a Ø 75 alu tube. Table Bracket Part No.: 2-5010-050 Used to mount System 50 Table Mounted Extraction Arms on table side which makes it removable for mobile installations. Made of black polyester powder coated steel. Other colours available on request. U-profile Part No.: 30-50-5-6 Used for reinforcement of the socket pipe when table mounting a System 50 extraction arm in table plate. Made of steel with a white polyester powder coated surface and an extra flange. Other colours for the U-profile are available on request. Reducer Part Nos.: 4-6350-6 & 4-8050-6 & 4-10075-6 Used to connect System 50 Extraction Arms or wall bracket to duct. Made of conductive polypropylene (PP). Reduces from/to Note Black 63/50 From extraction arm to duct 4-6350-6 80/50 From extraction arm to duct 4-8050-6 100/75 From wall bracket to duct Ø100 4-10075-6 GI 07
System 50 Antistatic General Information Accessories Overview Ceiling Columns Used for mounting the System 50 Ceiling Mounted Extraction Arms. The ceiling column is made of steel with a white or black polyester powder coating. Available in two models with side connection or top connection to duct. For standard lengths see below. Other lengths, colours or acid proof stainless steel (AISI 316L) available on request. Connection Diameter With top connection: max. 100 mm With side connection: 80 mm Length Weight app. [kg] White Black White Black 250 2.0 2-250-20 2-250-050-20 2-250-80** 2-250-050-80** 500 3.0 2-500-20 2-500-050-20 2-500-80 2-500-050-80 750 3.8 2-750-20 2-750-050-20 2-750-80 2-750-050-80 1000 4.5 2-1000-20 2-1000-050-20 2-1000-80 2-1000-050-80 1250 5.4 2-1250-20 - * 2-1250-80 - * 1500 6.1 2-1500-20 - * 2-1500-80 - * 1750 7.1 2-1750-20 - * 2-1750-80 - * 2000 7.9 2-2000-20 - * 2-2000-80 - * 2500 9.4 2-2500-20* - * 2-2500-80* - * Top connection *) Available on request **) For socket pipe with hole (Side connection only). Please contact your Alsident dealer. Side connection Support Bracket for long ceiling column Part No.: 2-75-5 For extra support of long ceiling columns. For support with wire to deck or by fastening to ceiling rail system. The support bracket is made of steel with a white polyester powder coating. Other colours available on request. Dimensions Internal: 100 x 100 mm External: 200 x 200 mm Cover Flange Part No.: 4-200-200 Made to cover the perforation through a concealed ceiling. To be glued on to the concealed ceiling around the ceiling column. Dimensions Internal: 100 x 100 mm External: 200 x 200 mm GI 08
System 50 Antistatic General Information Technical Description Pressure Drop Chart Tested by Danish Technological Institute A System 50, Table mounted B System 50, Wall- and Ceiling mounted A B GI 09
System 50 Antistatic General Information Spare Parts List Joint with Damper Joint with Damper 4-50-6 Pos. Part No. A 4-50-6 A 6 5 4 2.1 2 1.5 3 1 1.6 Pos. Spare part No. Description A 1 4-5012-6 Joint, 12 mm 1 1.1 5-75 Teflon Washer 1 1.2 5-75-5-6 Thumbscrew, 5 mm 1 1.3 5-75-4-6 Thumbscrew, 4 mm 1 1.4 5-5075 Wing for Damper 1 1.5 800-4-50-0-6 Damper 1 1.6 5-12-411 Seegerring 1 2 4-505-0-6 Joint, 5 mm 1 2.1 5-75-4-6 Thumbscrew, 4 mm 1 3 5-72-5-6 O-Ring 1 4 5-50-5-163 Threaded Stay 1 5 5-75 Teflon Washer 1 6 5-75-5-6 Thumbscrew 1 When ordering spare parts pos. 1 or 2 the underlying spare parts (1.1-1.6 or 2.1) are included. 1.3 1.4 1.1 1.2 [pieces applied] GI 10
System 50 Antistatic Table Mounting (TM) Working Area Table mounting with Suction Pen Note: A: Model 50-27-1-6 R: 445 mm B: Model 50-37-1-6 R: 545 mm C: Model 50-47-1-6 R: 645mm D: Model 50-3727-1-6 R: 765 mm E: Model 50-4737-1-6 R: 945 mm F: Model 50-5747-1-6 R: 1125 mm The working area of the arm is defined from the center of the opening of the accessory. The working area changes according to type of accessory and positioning. When chosing the arm we recommend that the stationary working position of the accessory is not placed in the highest or lowest part of the working area. (All measurements in mm) Accessories: Suction pen no. 1-5021-6 TM GI 01
System 50 Antistatic Table Mounting (TM) Mounting Options Table Mounted Option Dimensions Directly on table. System 50 Extraction Arm mounted directly on table top. Accessories: No brackets used. (all measurements in mm) MOUNTING INSTRUCTION On-line video or pdf www.alsident.com TM GI 02
System 50 Antistatic Table Mounting (TM) Mounting Options Table mounted option with Table Bracket Dimensions (all measurements in mm) With table bracket. System 50 Extraction Arm mounted on table side with a table bracket. Very functional option when impossible to mount directly on table or when a mobile installation is required. Accessories: Table Bracket, Part No. : 2-5010-050 MOUNTING INSTRUCTION On-line video or pdf www.alsident.com TM GI 03
System 50 Antistatic Table Mounting (TM) Table Bracket Technical Description Part No.: 2-5010-050 Dimensions (all measurements in mm) Used to mount System 50 Table Mounted Arms on table side. Removable for mobile installations. Made of steel with a black polyester powder coating on all surfaces. Other colours available on request. TM GI 04
System 50 Antistatic Table Mounting (TM) Mounting Options Table Mounted Option with U-profile above table Dimensions (all measurements in mm) U-profile above table System 50 antistatic Extraction Arm mounted with U-profile above table. Accessories U-profile, Part No.: 30-50-6 Mounting Instruction 1. Make a hole in the table with a max. diameter of 60 mm. Mount the socket pipe on the table with the screws enclosed. 2. Place the U-profile on the socket pipe and fasten it to the table. 3. Place the extra flange on the socket pipe and fasten it to the U-profile with the screws enclosed. 4. Place the extraction arm on the socket pipe. Make sure the internal spring goes into the socket pipe. 5. Follow the mounting instructions for the extraction arm. MOUNTING INSTRUCTION On-line video or pdf www.alsident.com TM GI 05
System 50 Antistatic Table Mounting (TM) Mounting Options Table mounted option with U-profile below table Dimensions (all measurements in mm) U-profile below table System 50 Extraction Arm mounted with U-profile below table. Accessories U-profile, Part No.: 30-50-6 Mounting Instruction 1. Make a hole in the table with a max. diameter of 60 mm. Mount the socket pipe on the U-profile with the screws enclosed. 2. Mount the U-profile with the socket pipe on the table. 3. Place the extra flange on the socket pipe and fasten it to the table with the screws enclosed. 4. Place the extraction arm on the socket pipe. Make sure the internal spring goes into the socket pipe. 5. Follow the mounting instructions for the extraction arm. MOUNTING INSTRUCTION On-line video or pdf www.alsident.com TM GI 06
System 50 Antistatic Table Mounting (TM) U-profile Technical Description Part No.: 30-50-5-6 Dimensions (all measurements in mm) Used for reinforcement of the socket pipe when table mounting a System 50 antistatic extraction arm in table top. U-profile can be placed both above and below the table. Made of steel with a white polyester powder coated surface and an extra flange. Other colours for the U-profile are available on request. TM GI 07
System 50 Antistatic Table Mounting (TM) Spare Parts (A) 50-27-1-6 (B) 50-37-1-6 (C) 50-47-1-6 30-37-1-6 50-5747-1-6 6 7 1 (D) 50-3727-1-6 (E) 50-4737-1-6 (F) 50-5747-1-6 6 7 5 10 2 3 10 6 7 5 8 2 3 1 7 6 3 5 7 6 4 9 7 Spare Parts List see next page 6 9 4 TM GI 08
System 50 Antistatic Table Mounting (TM) Spare Parts List Pos. Part No. Joint A B C D E F 50-27-1-6 2-joint 50-37-1-6 2-joint 50-47-1-6 2-joint 50-3727-1-6 3-joint 50-4737-1-6 3-joint 50-5747-1-6 3-joint Pos. Spare part No. Description A B C D E F 1 3-5031-1-6 C-pipe TM 315 1 1 1 1 1 1 2 5-50-2-3-02 Spring TM 3 mm (2-joint) 1 1 2 5-50-3-3-02 Spring TM 3 mm 1 2 5-50-3-4-02 Spring TM 4 mm 1 1 3 5-72-5-6 O-Ring 1 1 1 2 2 2 4 3-5027-9-6 B-pipe 275 1 1 4 3-5037-9-6 B-pipe 375 1 1 4 3-5047-9-6 B-pipe 475 1 1 5 5-50-5-154 Threaded Stay 1 1 1 2 2 2 6 5-75-5-6 Thumbscrew 2 2 2 4 4 4 7 5-75 Teflon Washer 2 2 2 4 4 4 8 3-5037-8-6 A-pipe 375 1 8 3-5047-8-6 A-pipe 475 1 8 3-5057-8-6 A-pipe 575 1 9 4-50-6 Joint with damper* 1 1 1 1 1 1 10 4-505-6 Joint, 5 mm 1 1 1 1 1 1 *) Spare Parts List for joint with damper see General Information When ordering spare parts please quote: Part No. eg.: 50-37-1-6 Description - B-pipe 375 Spare Part No. - 3-5037-9-6 Quantity - 1 pc. [pieces applied] If you wish to customize the arm with a spare part which is not a constituent part of the particular model, please contact your Alsident dealer. TM GI 09
System 50 Antistatic Wall/Ceiling Mounted (WCM) Working Area Wall mounting with Suction pen Note: A: Model 50-37-3-6 R: 530 mm B: Model 50-47-3-6 R: 630 mm The working area of the arm is defined from the center of the opening of the accessory. The working area changes according to type of accessory and positioning. When chosing the arm we recommend that the stationary working position of the accessory is not placed in the highest or lowest part of the working area. (All measurements in mm) C: Model 50-3727-3-6 R: 750 mm D: Model 50-4737-3-6 R: 910 mm E: Model 50-5747-3-6 R: 1080 mm F: Model 50-8747-3-6 R: 1380 mm Accessory: Suction pen no. 1-5021-6 WCM GI 01 01
System 50 Antistatic Wall/Ceiling Mounted (WCM) Mounting Options Wall Mounted Option Dimensions (all measurements in mm) Wall Mounted System 50 Extraction Arm with the wall bracket. Accessories Wall Bracket, Part no.: 2-195-050 MOUNTING INSTRUCTION On-line video or pdf www.alsident.com WCM GI 02 02
System 50 Antistatic Wall/Ceiling Mounted (WCM) Wall Bracket Technical Description Part No.: 2-195-050 Dimensions (all measurements in mm) For wall mounting of System 50 extraction arms. Made of steel with a polyester powder coating in black on all surfaces. Other colours available on request. Three options available for the connection to the duct: 1) Directly from the top of the bracket to a Ø 80 mm spiro duct. 2) With reducer 4-10075 to a Ø 100 mm spiro duct (reducer included). 3) Directly from the top of the bracket to a Ø 75 alu tube. WCM GI 03 03
System 50 Antistatic Wall/Ceiling Mounted (WCM) Working Area Ceiling mounting with Suction pen Note: A: Model 50-37-3-6 R: 530 mm B: Model 50-47-3-6 R: 630 mm The working area of the arm is defined from the center of the opening of the accessory. The working area changes according to type of accessory and positioning. When chosing the arm we recommend that the stationary working position of the accessory is not placed in the highest or lowest part of the working area. (All measurements in mm) C: Model 50-3727-3-6 R: 750 mm D: Model 50-4737-3-6 R: 910 mm E: Model 50-5747-3-6 R: 1080 mm F: Model 50-8747-3-6 R: 1380 mm Accessory: Suction pen no. 1-5021-6 WCM GI 04 04
System 50 Antistatic Wall/Ceiling Mounted (WCM) Mounting Options Ceiling Mounted Option Dimensions (all measurements in mm) Ceiling Mounted System 50 Extraction Arm ceiling mounted with a ceiling column. Connection for duct at the side or top. Accessories: Ceiling Column, Part No. depending on lengths. MOUNTING INSTRUCTION On-line video or pdf www.alsident.com WCM GI 05 05
System 50 Antistatic Wall/Ceiling Mounted (WCM) Ceiling Column Technical Description Sokkelkasser Ceiling Columns Used for mounting the System 50 Ceiling Mounted Extraction Arms. The ceiling column is made of steel with a white or black polyester powder coating. Available in two models with side connection or top connection to duct. For standard lengths see below. Other lengths, colours or acid proof stainless steel (AISI 316L) available on request. Connection diameter With top connection: With side connection: Top connection, Part No.: max. 100 mm 80 mm Length Weight app. [kg] White Black 250 2.0 2-250-20 2-250-050-20 500 3.0 2-500-20 2-500-050-20 750 3.8 2-750-20 2-750-050-20 1000 4.5 2-1000-20 2-1000-050-20 1250 5.4 2-1250-20 - * 1500 6.1 2-1500-20 - * 1750 7.1 2-1750-20 - * 2000 7.9 2-2000-20 - * 2500 9.4 2-2500-20* - * *) Available on request **) For socket pipe with hole. Please contact your Alsident dealer. Dimensions (all measurements in mm) Side connection, Part No.: Length Weight app. [kg] White Black 250** 2.0 2-250-80 2-250-050-80 500 3.0 2-500-80 2-500-050-80 750 3.8 2-750-80 2-750-050-80 1000 4.5 2-1000-80 2-1000-050-80 1250 5.4 2-1250-80 - * 1500 6.1 2-1500-80 - * 1750 7.1 2-1750-80 - * 2000 7.9 2-2000-80 - * 2500 9.4 2-2500-80* - * WCM GI 06 06
System 50 Antistatic Wall/Ceiling Mounted (WCM) Spare Parts List (A) 50-37-3-6 (B) 50-47-3-6 50-47-3-6 6 7 1 3 (C) 50-3727-3-6 (D) 50-4737-3-6 (E) 50-5747-3-6 (F) 50-8747-3-6 50-5747-3-6 9 6 7 5 6 7 5 8 3 2 9 3 4 4 7 2 6 Spare Parts List see next page. 5 1 7 7 6 6 WCM GI 07 07
System 50 Antistatic Wall/Ceiling Mounted (WCM) Spare Parts List Pos. Part No. Joint A B C D E F 50-37-3-6 2-joint 50-47-3-6 2-joint 50-3727-3-6 3-joint 50-4737-3-6 3-joint 50-5747-3-6 3-joint 50-8747-3-6 3-joint Pos. Spare part No. Description A B C D E F 1 3-5031-3-6 C-pipe WCM 315 1 1 1 1 1 1 2 5-50-2-3-03 Spring WCM 3 mm (2-joint) 1 1 2 5-50-3-3-03 Spring WCM 3 mm 1 2 5-50-3-4.5-03 Spring WCM 4.5 mm 1 1 2 5-50-3-5-03 Spring WCM 5 mm 1 3 5-72-5-6 O-Ring 1 1 2 2 2 2 4 3-5027-9-6 B-pipe 275 1 4 3-5037-9-6 B-pipe 375 1 1 4 3-5047-9-6 B-pipe 475 1 1 1 5 5-50-5-154 Threaded Stay 1 1 2 2 2 2 6 5-75-5-6 Thumbscrew 2 2 4 4 4 4 7 5-75 Teflon Washer 2 2 4 4 4 4 8 3-5037-8-6 A-pipe 375 1 8 3-5047-8-6 A-pipe 475 1 8 3-5057-8-6 A-pipe 575 1 8 3-5087-8-6 A-pipe 875 1 9 4-50-6 Joint with damper* 1 1 1 1 1 1 *) Spare Parts List for joint with damper see General Information When ordering spare parts please quote: Part No. eg.: 50-3727-3-6 Description - B-pipe 275 Part No. - 3-5027-9-6 Quantity - 1 pc. [pieces applied] If you wish to customize the arm with a spare part which is not a constituent part of the particular model, please contact your Alsident dealer. WCM GI 08 08