X-Cruiser Series Installation Guide 1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs from Side Panel. pull out. from the enclosed screw box. 4:Put the motherboard stand-offs 5.Sit the motherboard on the on the motherboard tray. motherboard tray. 6.Find screws in the screw box. 7.Screw in all the screws into the 8.Same as Step 7. motherboard stand-offs
9.Take out front panel: (Optional. Only if you need to install front fans or replace LCD) Step (1): Unscrew the side panel Step (2): Take out the side Step (3): There are 4 screws that panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2 on each side) Unscrew the 2 screws from inside of the case. Step (4): Unscrew the other Step (5): Pull out the front 10.Front Case Fans (Optional): 2 screws from the other side. panel from the bottom. You can put up to 2*80mm fans in the front. 11.Put the front panel back 12.5.25 Drives: Open the door 13.Insert 5.25 drivers. and screw to secure. and force out the 5.25 metal plate and drive cover from inside with a screw driver.
14.Screw all 5.25 drives 15.3.5 External Drives: 16.Insert external 3.5 drives in place. Force out 3.5 metal plate and and secure with screws in place. drive cover with a screw driver. 17.3.5 Internal Drives: 18.Screw all 3.5 hidden drivers 19.Find the 20-pin connector Install 3.5 hidden drivers such in place. from Power Supply. as hard drive and zip drive. 20.Plug into your motherboard. 21.Find the 4-pin P4 connector 22.Plug into your motherboard. Different M/B has different layout. from power supply.(for P4 only) (For Intel P4 motherboard only) Please refer to M/B user manual.
23.Find 2*USB Cables.(USB1 24.Plug USB cables to your M/B. 25.Find HDD LED and & USB2) Please refer to M/B User Manual. Reset SW cables. 26.Plug them onto your M/B. Please refer to M/B user manual. 27.Find Power SW and +P LED 28.Find Case Speaker from -P LED cables and plug onto M/B. screw box. Please refer to M/B user manual. 29.Install case speaker onto M/B 30. Install LED Lights: Find 2* 31.Connect the 4-pin Male connector following M/B user manual. LED connectors from the front to a 4-pin connector Female from Panel. They are 2*2-pin power supply. connectors that lead out to2*4-pin connector (1*Male, 1*Female)
32.LCD Temperature Readout: 33.Remove the protective plastic 34.This is the temperature Connect 4-pin Male connector from tube from the sensor. sensor. It s very fragile. LCD to a 4-pin Female connector Be gentle. from power supply. 35.You can either tape the sensor on hard drive or on CPU Heat 36.Once powered on, the LCD sink or leave it inside the case to get the overall system temperature. shows temperature readout with back lighting 37.Fan Speed Controller: Find a 38.Link all case fans cables 39.Then connect the Male end to 4pin male connector from front together. There will be 1*Male a 4pin Female (output) from the panel with Input DC 12V and and 1*Female left out at each front panel fan speed controller connector it to a 4pin female end. unit. connector from power supply.
40.After connecting the fan 41.Once the audio cable is plug 42.There are volume and speed controller, you would be into motherboard, the volume fan speed adjusters on the able to read the fan speed from gauge will show the sound side of front panel. the front fan speed gauge. Volume. 43.Find Case Feet in the screw box. 44.View from front panel 45.View of top panel fan w/ Lay case down and put Case Feet on. After installation. Fan grill and filter. Note: 1.You can link together all the 4-pin connectors(male to female) from all the case fans, LCD, LED, HDD and just use one of the 4-pin Molex connectors from power supply. That will leave you more 4-pin Molex connectors from your power supply for other devices.
PIN ASSIGNMENT Description Signal Color DIAGRAM Color Signal Description USB Power (+5V) for Port 2 VCC RED RED VCC USB Power (+5V) for Port 1 USB Negative Signal for Port 2 -D WHITE WHITE -D USB Negative Signal for Port 1 USB Positive Signal for Port 2 +D GREEN GREEN +D USB Positive Signal for Port 1 USB GROUND GROUND BLACK BLACK GROUND USB GROUND KEY NC USB Function Front Microphone Input Signal MIC-IN BROWN BLACK GROUND Front Audio Ground Front Microphone Power MIC-POWER BLUE NC Front Right Channel Audio Signal R-OUT ORANGE ORANGE R-RET Rear Right Channel Audio Signal NC KEY Front Left Channel Audio Signal L-OUT RED RED L-RET Rear Left Channel Audio Signal AUDIO Function TPA+ BLUE ORANGE TPA- GROUND BLACK NC TPB+ GREEN RED TPB- NC WHITE VP KEY BLACK GROUND 1394 Function