R R Debris Blower Operator s Manual DB00 DB600 5/0 /0
Thank you for purchasing a Harper. As with all Harper products, the has been developed through tough design and testing procedures to produce a top quality machine. This manual gives assembly, operating, and service information for the models DB00 and DB600. Please read and understand all instructional material included with the or its components before assembling and operating the equipment. A can present hazards to an operator who follows unsafe procedures in either the operation or maintenance of the unit. Therefore, SAFETY WARNINGS are presented at certain locations in the text. THIS SYMBOL: SAFETY WARNING! MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your dealer or Harper Industries, Inc. for clarification. SAFETY WARNING! ALL SHIELDS AND GUARDS MUST BE IN PLACE FOR PROPER AND SAFE OPERATION OF THIS EQUIPMENT. WHERE THEY ARE SHOWN REMOVED IN THIS MANUAL, IT IS FOR PURPOSES OF ILLUSTRATION AND INSTRUCTION ONLY. DO NOT OPERATE THIS EQUIPMENT UNLESS ALL SHIELDS AND GUARDS ARE IN PLACE. Harper Industries, Inc. is continually striving to improve the design and performance of its products. We reserve the right to make changes in specifications and design without thereby incurring any obligation relative to previously manufactured products. 0 Harper Industries, Inc. The Harper name is a registered trademark of Harper Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies.
LIMITED WARRANTY The Harper is warranted against defects in workmanship and materials for a period of TWELVE MONTHS from the original date of retail purchase to the original purchaser. Harper Industries will repair or replace, at our option, any part which our examination shows to be defective. Warranty is limited to parts, labor and ground freight delivery of replacement parts. The user will pay freight charges for parts submitted under this warranty. No product or part may be returned for warranty consideration without prior approval from Harper Industries. This warranty does not apply to parts subjected to misuse, abuse, alteration, improper or inadequate maintenance, or normal wear (including belts and broom). Engines are not covered under this warranty. Refer to manufacturer s warranty for specific warranty information. Harper Industries, its agents or representatives, make or imply no other warranties. RECORDS Date of Purchase / / Dealer s Name Dealer s Phone Serial Number Machine Serial Number Engine
Table of Contents OPERATOR SECTION To the Owner or Operator... Warranty Statement... Table of Contents... Specifications... Safety Information Equipment & Control... Guards & Shields... Safety Decals... Before Operation... Operation... Control Identification PTO Shaft... -Point Hitch Pins... Input Shaft... Diverter Handle Assy... Belt Tensioner... Impeller Shaft... Caster Wheels... Assembly... Operation To begin operation... To stop operation... Adjustments Belt Tension Adjustment... Cable Adjustment... Service & Maintenance Break-in Service... Lubrication... Troubleshooting Belts... Standard Torque Chart... PARTS SECTION DB00 Components... Diverter... PTO - 9005... PTO - 9... PTO - 905... Decals... DB600 Components... Diverter... PTO - 900... PTO - 90... PTO - 900... PTO - 906 (current)... Decals... 5 5 5 5 6 9 9 0 0 0 0 6 0 6 9 0
Specifications Air Flow: Noise: Blower Housing: Fan: Drive: Belt Drive: Tractor Mounting: Casters: Anit-Scalp: Dimensions: Air-Flow Control: Approx. Weight: Power Requirement: 600 00 600 00 600 00 600 00 600 00 600 00 600 00 600 00 00 CFM (approx. 5 mph) 000 CFM (approx. 0 mph) 9 decibels (At operator in tractor seat.) decibels 0 (Split design for east fan replacement.) 6 diameter diameter 50 RPM PTO belt drive - 5VX50 V-belts with automatic tensioner - /CX5 Point Hitch - Category # Heavy-duty 0 adjustable caster wheels Heavy-duty adjustable caster wheels Tough diameter rollers Length, Width 6, Height 5 Length, Width, Height 6 Bi-directional discharge (left or right) controlled from operator seat 5 lbs. 5 lbs. 0 hp at PTO (minimum) 0-0 hp at PTO Superior Construction in every model: Every Harper has a durable polyester baked paint finish, with epoxy primer applied to cover completely and keep moisture out. This finish is extremely strong, and resists chipping and cracking.
Safety Information Equipment & Controls Altering this equipment in any manner which adversely affects its operation, performance, durability, or use will void the warranty and may cause hazardous conditions. Know the location and function of all controls and how to stop this equipment quickly in an emergency before you operate the equipment. READ AND UNDERSTAND THE OWNER S MANUAL. Keep all nuts, bolts and screws tight to help ensure safe operation of this equipment. Use genuine factory parts or parts with equivalent characteristics, including type, strength and material. Failure to do so may result in product malfunction and possible injury to the operator and/or others. Replace locknuts and locking screws if you can tighten them without feeling considerable resistance for several turns before they are completely tight. Replace them with factory authorized parts or their equivalent. If hardware is not secure, or if some of the hardware is over-tightened, equipment failure may result, posing possible safety hazards. Guards & Shields Keep the equipment and attachments in good operating condition, and keep all safety devices in place. Replace all worn, damaged, unusable, missing or lost safety shields and guards before operating the equipment. Safety Decals If safety related or instructional decals become illegible or are removed, replace them immediately. If you replace parts that have such decals attached to them, make sure the decals are replaced with current versions, and that the decals are on the replacement parts before the machine is operated again. New decals may be obtained from your local Harper Dealer. SAFETY WARNING! To prevent possible eye injury, always wear SAFETY GLASSES while servicing the equipment. Before Operation Before operating this equipment, read and understand the Owner s Manual. Do not allow children to operate this machine. Never operate this machine in the vicinity of bystanders. Before servicing or inspecting the machine, make certain that the power source is shut down, make certain all moving parts have stopped and disconnect the PTO shaft. 5
Never allow hands, clothing or any part of the body to enter the discharge chute or near moving parts. Avoid wearing loose-fitting clothing. Wear approved eye and ear protection while operating the machine. The machine should be operated on level surfaces only. Before starting the machine, visually inspect all nuts, bolts and other fasteners to see that they are properly secured. Nuts, bolts and other fasteners should be checked every to 0 hours of operation for proper alignment and tightness. Operation Make certain the impeller chamber is empty before starting the machine. If a foreign object should strike the impeller mechanism of the machine and cause an unusual noise or vibration, shut the engine or PTO off immediately and allow it to come to a complete stop. Disconnect the spark PTO shaft from the power unit, and then do the following:. Inspect for damage.. Repair or replace any damaged parts.. Check for and tighten any loose bolts, nuts, fasteners or parts. Keep debris material from building up in the discharge and inlet area, as this may prohibit proper discharge of airflow and can cause poor performance. Keep the impeller inlet area clean from debris and other accumulations. Keep your face and all body parts away from inlet and discharge openings. Stay away from the discharge area when machine is in operation. If the should become clogged, shut off the engine or PTO and allow it to come to a complete stop. Disconnect the spark plug wire from the spark plug or PTO shaft before clearing debris. Do not allow hands, clothing or any part of the body to enter the discharge chute, impeller inlet or near any moving parts. Replace damaged or missing safety decals. Keep hands, feet and clothing away from PTO driven parts. Keep all guards and shields in place during operation. Disengage PTO and shut off the engine before removing guards or shields. Never attempt to adjust, clean or lubricate the machine while it is in operation. Operator should never wear loose clothing when working around PTO. Before starting tractor, make sure that the transmission and PTO are disengaged. Make sure the tractor s engine is at idle speed before engaging the PTO. Be sure the tractor s engine is at idle before changing the airflow of the Diverter. Keep all safety shields and guards in place and in good working condition. 6
Control Identification Diverter Handle Assembly Impeller Shaft PT. Hitch Pins Input Shaft PTO Shaft Caster Wheels. PTO Shaft Transfers power from the tractor to the. Make sure up or down angle of PTO shaft does not exceed 5 degrees. ( grease fittings). -Point Hitch Pins Mount the Debris Blower to the -point hitch pins.. Input Shaft Driven by the PTO shaft. Always disconnect the PTO from the tractor when performing maintenance. ( grease fittings). Diverter Handle Assembly Changes direction of discharge air flow. Make sure handle is locked into place before operating. 5. Belt Tensioner Spring loaded and keeps the belts within proper tension ing. 6. Impeller Shaft Belt driven by input shaft. ( grease fittings). Caster Wheels Carry weight of machine during operation when -point hitch is in float position. ( grease fitting per wheel) SAFETY WARNING! Keep all safety shields in place during operation.
Assembly. Remove from crate.. Mount Diverter Handle Assembly to the frame of the machine with the two / bolts already in the frame.. Connect PTO shaft to input shaft of machine, tighten set screws on shaft.. Mount -point pins on. 5. Mount to -point of tractor and connect PTO shaft. Note: A set of belts between the PTO shaft and the impeller shaft assembly drive the fan blades whenever the PTO drive-shaft is turning. On initial operation of the Debris Blower, the belts may shrink and need readjustment after the first hour of use. When readjusting belt tension, use a straightedge across the faces of pulleys to make sure they are properly aligned and the belts will run true. SAFETY WARNING! Keep pants and loose clothing away from PTO drive and shaft and all drive pulleys, belts and shafts. Never operate the beyond the suggested 50 PTO speed. Do not attempt to service machine while it is in operation. Operation SAFETY WARNING! Wear approved eye and ear protection while operating the. Keep all guards in place during operation. Never operate the Debris Blower with safety shields removed. Before operating the machine, check to ensure that all belt guides and tensioner are in place to prevent belts from slipping off the pulleys and systems from being accidentally engaged. Check inlet and discharge housings for children, pets and foreign objects before operating. Keep clothing and all body parts away from rotating parts. Do not wear loose fitting clothing. Periodically clean debris material away from the machine to lessen the possibility of fire. Always keep a fire extinguisher near the Debris Blower during operation. Impeller blade rotation cannot be controlled from the. Obtain and wear safety glasses when operating this machine. Note: A safe operator is one who practices safety and uses good common sense to protect himself from flying material.
To begin operation:. Mount to -point of tractor and connect PTO shaft to tractor output shaft.. Adjust center link on tractor so that the is setting level at the ground surface while -point hitch is in FLOAT position.. Move Diverter Handle to the desired output direction.. Engage PTO lever on the tractor AT IDLE SPEED of the tractor and begin operation of the. 5. If the operator needs to change direction of airflow of the diverter, make sure the tractor is at idle speed. To stop operation:. Move throttle on tractor to the slow position and disengage the PTO lever on the tractor.. Shut off the tractor engine and allow the machine to come to a complete stop. SAFETY WARNING! The Impeller is heavy and will continue to turn even though the operator has shut off the power source. Do not attempt to service or inspect the machine until you see that the shafts have stopped turning and that there is no noise coming from the machine. 6. If it is necessary to inspect or work on the, always disengage the PTO shaft and shut off the tractor engine before doing so. SAFETY WARNING! Belts may become severely damaged by engaging PTO shaft at high RPM. To avoid personal injury, always keep face and body parts away from inlet and discharge openings. Never leave this machine unattended. Make sure the tractor engine has been shut off and the PTO shaft has been disconnected before attempting any service or inspection. 9
Adjustments Belt Tension Adjustment Check the condition of drive belts before each use or after every 5 hours of operation. Note: Use only industrial V-belts. Do not use automotive belts. Do not over-tighten belts. Excessive tension can cause premature bearing and belt failure. Use a straightedge to check alignment across the faces of pulleys after adjusting belt tension to ensure that the belts will run true. Cable Adjustment Check the condition of the diverter cable before each use or after every 5 hours of operation. SAFETY WARNING! Never operate with out ALL GUARDS in place. Service & Maintenance SAFETY WARNING! Before servicing or inspecting the, make sure the power source is shut off and all moving parts have stopped. Disconnect the PTO shaft from the tractor. Always wear safety glasses and protective gloves when servicing the. Break-in Service After the first hour of use:. Check belts. Re-tension if needed.. Tighten set screws on bearings.. Check nuts, bolts and fasteners to see that they are secure. Lubrication. Lubricate grease fittings on unit after every 5 hours of use.. There are grease fittings on the unit: on the PTO Shaft on the Input Shaft on the Impeller Shaft on each Caster Wheel () 0
Troubleshooting Belts: Problem: Belts Slip What to Check: Tension adjustment Load may be excessive Bearings may have seized. Problem: Belts wear rapidly, jump, catch, or twist. What to Check: Pulleys may not be properly aligned Check with straightedge across face of pulleys Standard Torque Chart Size In-lbs Ft-lbs N-M No. 0-5-5 5-.-.0 / in. 60-0 -0-9 5/6 in. 0-0 -0-6 / in. 0-60 6- - / in. 6-50 90-00 Note: When tightening two or more screws on the same part, DO NOT tighten screws completely right away, or one at a time. To avoid distortion, first tighten all screws in sequence to one-third of torque value, then tighten to two-thirds of torque value, then tighten to full value.
R Debris Blower R Parts Section Operator s Manual DB00 DB600 /0
Table of Contents PARTS SECTION DB00 Components... Diverter... PTO - 9005... PTO - 9... PTO - 905... Decals... DB600 Components... Diverter... PTO - 900... PTO - 90... PTO - 900... PTO - 906 (current)... Decals... 6 0 6 9 0 5
ITEM QTY 5 5 6 9 0 9 5 6 6 9 9 0 5 6 9 0 5 6 9 0 5 6 9 50 5 5 6 PART # 00 00 05 0 005 0 05 09 05 09 00 06 0596 060 06 065 065 065 0666 0 0 0 060 5009 50 50 6055 0 066 00 9000 900 9065 950 950 95 955 95 955 955 9559 90009 900 900 90 90 9 95 9 9 905 95000 Parts List DESCRIPTION WASHER, " FLAT STANDARD NUT, /-6 GR BOLT, /6- X.5 BOLT, /-0 X 6.5, HEX HEAD Pin, Lynch /6 x / NUT, /6- WIZ FLANGE /-0 U-TYPE TAPPED HOLE BOLT, /- X.0 BOLT, /-6 X.5 BOLT, /- X.5 BOLT, /-6 X, WIZ FLANGE BOLT, /-0 X 0.5, WIZ FLANGE NUT, /-0 NUT, /- NUT, /-6 LOCK NYLON INSERT NUT, /-0, UNITORQUE LOCK NUT, /-6 WIZ FLANGE WASHER, /" FLAT STANDARD WASHER, /" LOCK NUT, /-0 U-TYPE,.-.9 X.5 BOLT, /-0 X.5 TAP BOLT, /- X TAP SetScrew, /-6 X.5 KEY, / X / X.5 in GREASE ZERK, /- ST WHEEL ASSY / CASTER KEY, / X / X.0 in BUSHING/IDLER IDLER,.9" OD X.66 ID X. W FLAT BUSHING, MFI-60- -POINT PIN W/ HARDWARE HITCH STIFFENER SPACER,.5 X. X.95 CASTER MOUNTING WELDMENT CASTER YOKE WELD ASSY MAIN FRAME HOOD SMALL IMPELLER WELDMENT SMALL HITCH WELDMENT SHIELD WELDMENT TENSIONER WELDMENT BEARING, PB SD PILLOW BLOCK BEARING, (.5) SMALL DB FAN SHAFT SMALL DB INPUT SHAFT DRIVE V-BELT GROOVE POWERBAND SHEAVE /V.65-60 SHEAVE, /V 0.6-5 BUSHING, QD -/" SH BUSHING, QD " SH PTO SHAFT SPACER DB00 COMPONENTS 5//0 6
DB00 COMPONENTS 6 9 0 9 5 5 50 6 SEE PTO SHAFT FOR SERVICE PARTS 9 0 5 0 9 5 5 6 5 0 5 5 9 6 6 5//0
DB00 DIVERTER ITEM QTY 9 5 6 9 9 0 5 6 PART # 005 0 00 0 060 0606 065 500 90 9050 9056 95 956 95 959 95500 Parts List DESCRIPTION BOLT, /-6 X.0 BOLT, 5/6- X.5 BOLT, /-6 X, WIZ FLANGE BOLT, 5/6- X 0.5, WIZ FLANGE NUT, 5/6- LOCK (NYLON) NUT, 5/6- WIZ FLANGE NUT, /-6 WIZ FLANGE ROLL PIN, /6 X.5 TURF ROLLER (") DIVERTER BRACKET ROLLER AXLE, SMALL DB DIVERTER HANDLE ASSY DISCHARGE DIVERTER GATE WELDMENT SMALL DIVERTER PIVOT WELDMENT DIVERTER CABLE ASSY /6/0
6 DB00 DIVERTER 9 6 6 5 0 5 /6/0 9
DB00 PTO SHAFT PART NO. 9005 (OBSOLETE - PTO ASSY REPLACED BY 9) 6 9 ITEM 5 6 9 QTY PART # 60009 5005 90 905 9 99 90 9 96 Service Parts List DESCRIPTION DECAL, DANGER ROTATING DRIVE (NOT SHOWN) DECAL, DANGER (NOT SHOWN) YOKE, IMPLEMENT END " BORE BEARING SET, COMPLETE AW0 YOKE, SNAP HITCH AW0 CROSS & BEARING KIT, AW0 YOKE, SHAFT WELD AW0 YOKE, TUBE WELD AW0 GUARD SET 5 5//0 0
DB00 PTO SHAFT PART NO. 9 USED ON S/N: PRIOR TO A6 (OBSOLETE - PTO ASSY REPLACED BY 905) Table QTY PART # DESCRIPTION 9 JOINT & SHAFT HALF ASM. W/ GUARD 9 JOINT & SHAFT HALF ASM 9 JOINT & TUBE HALF ASM W/ GUARD 9 JOINT & TUBE HALF ASM 00 SPRING-LOK REPAIR KIT 95 SPRING-LOK YOKE ASM 006 R CROSS KIT 96 YOKE & SHAFT (.00 X. RECT.) 9 GUARD REPAIR KIT 9 OUTER GUARD 600 SAFETY SIGN 99 SAFETY SIGN 90 INNER GUARD 9 YOKE, TUBE, & SLIP SLEEVE 9 YOKE 506 SET SCREW, /-6 X.50 LNGTH 5//0
DB00 PTO SHAFT PART NO. 905 USED ON S/N: A6 - CURRENT Table QTY PART # DESCRIPTION 95 JOINT & SHAFT HALF ASM W/ GUARD 95 JOINT & SHAFT HALF ASM 95 JOINT & TUBE HALF ASM W/ GUARD 955 JOINT & TUBE HALF ASM 00 SPRING-LOK REPAIR KIT 95 SPRING-LOK YOKE ASM 006 R CROSS KIT 956 YOKE & SHAFT (.OO X. RECT) 95 OUTER GUARD 9 GUARD REPAIR KIT 600 SAFETY SIGN 99 SAFETY SIGN 95 INNER GUARD 959 YOKE & TUBE 9 YOKE 506 SET SCREW, / X.50 LGTH 5//0
R R 9069 9000 90060 READ AND UNDERSTAND ALL INSTRUCTIONS AND SAFETY WARNINGS BEFORE OPERATING THIS EQUIPMENT. DO NOT OPERATE MACHINE IN THE VICINITY OF BYSTANDERS OR ANIMALS. NEVER DIRECT DISCHARGE TOWARDS BYSTANDERS OR OBJECTS SUCH AS CARS, BUILDINGS, ETC. ALWAYS WEAR A DUST MASK WHEN OPERATING IN DUSTY CONDITIONS. EYE AND EAR PROTECTION MUST BE WORN AT ALL TIMES. NEVER ALLOW PASENGERS ON THE MACHINE. KEEP HANDS, FEET AND CLOTHING AWAY FROM MOVING PARTS (ENTANGLEMENT CAN CAUSE SERIOUS INJURY OR DEATH). SHUT TRACTOR OFF AND ALLOW ALL MOVING PARTS TO COME TO A COMPLETE STOP BEFORE PERFORMING SERVICE OR REPAIR WORK. WARNING FAILURE TO FOLLOW SAFE OPERATING PROCEDURES CAN RESULT IN DEATH OR SERIOUS INJURY. 906 90000. KEEP HANDS, FEET AND CLOTHING AWAY FROM POWER-DRIVEN PARTS.. IF MECHANISM BECOMES CLOGGED DISCONNECT POWER BEFORE CLEANING. STOP MACHINE TO ADJUST & LUBRICATE.. KEEP ALL GAURDS IN PLACE. CAUTION Failure to use hearing protection may cause permanent loss of hearing. WARNING 9000 000 000 SHIELD HAS BEEN REMOVED! REPLACE PRIOR TO MACHINE OPERATION WARNING UNDER SHIELD DB00 - DECAL PLACEMENT 9000 DECAL KIT 90505 9069 0/6/0 50006
ITEM 5 6 9 0 5 6 9 0 5 6 9 0 5 6 9 0 5 6 9 QTY 9 9 6 6 PART # 0056 0056 00 06 05 0 005 05 09 00 0 059 050 0606 060 066 06 065 065 066 0666 0009 0009 00 9000 900 900 90 90 9500 950 950 950 950 9505 950 950 9000 900 900 900 900 900 9 9 9 906 95000 Parts List DESCRIPTION KEY, / X / X.5 in ROLL PIN, / X.5 WASHER, " FLAT STANDARD NUT, 5/- JAM BOLT, /- X.5 GR 5 ZINC PLATE BOLT, /-0 X 6.5, HEX HEAD CAP SCREW Pin, Lynch /6 x / BOLT, /-6 X.5 BOLT, /- X.5 BOLT, /-6 X, WIZ FLANGE BOLT, 5/6- X 0.5, WIZ FLANGE BOLT, 5/6- X, WIZ FLANGE BOLT, 5/- X.5 NUT, 5/6- WIZ FLANGE NUT, /- NUT, 5/6", J-TYPE, CAGE,.5C NUT, /-6 LOCK NYLON INSERT NUT, /-0, UNITORQUE LOCK NUT, /-6 WIZ FLANGE WASHER, /" FLAT SPECIAL.5od WASHER, /" LOCK Pin, Lynch /6-P BUSHING, QD.5" E CASTER WHEEL ASSY BUSHING, MFI-60- -POINT PIN W/ HARDWARE HITCH STIFFENER IDLER MOUNT STIFFENER TENSION MOUNT WASHER ACCESS DOOR HITCH WELDMENT IMPELLER WELDMENT IDLER MOUNT WELDMENT CASTER MOUNTING WELDMENT CASTER YOKE WELD ASSY BELT SHIELD WELDMENT HOOD WELDMENT MAIN FRAME WELDMENT IMPELLER SHAFT INPUT SHAFT BELT IDLER TENSIONER PILLOW BLOCK BEARING, (.5) DRIVE IDLER DRIVE BELT, (5V X 50) SHEAVE, /5V 5.0 SD-QD SHEAVE, /5V.0 E-QD BUSHING, QD -/" SD PTO SHAFT ASSY SPACER DB600 COMPONENTS 5//0
DB600 COMPONENTS 5 0 5 9 0 5 6 5 0 5 SEE PTO SHAFT FOR SERVICE PARTS 5 6 0 6 6 0 9 5 5 0 9 9 5 9 6 0 5//0 5
DB600 DIVERTER ITEM 5 6 9 0 5 6 QTY 0 5 PART # 0 06 00 059 0556 060 0606 065 50 905 906 90 9050 95 95 955 95 95500 Parts List DESCRIPTION BOLT, 5/6- X.5 BOLT, /-6 X.5 BOLT, /-6 X, WIZ FLANGE BOLT, 5/6- X, WIZ FLANGE Bolt, /-6 X in Carriage NUT, 5/6- LOCK (NYLON) NUT, 5/6- WIZ FLANGE NUT, /-6 WIZ FLANGE COTTER PIN, /6 X ROLLER AXLE TURF ROLLER (6") TURF ROLLER (") DIVERTER BRACKET DIVERTER PIVOT WELDMENT DIVERTER GATE WELDMENT DISCHARGE WELDMENT DIVERTER HANDLE ASSY DIVERTER CABLE ASSY //0 6
DB600 DIVERTER 0 5 9 6 5 6 //0
DB600 PTO SHAFT - R PART NO. 900 - (OBSOLETE) USED ON S/N: 0A0-0A50 (PART NO. 900 MAY BE USED TO REPLACE COMPLETE PTO SHAFT) ITEM 5 6 9 0 5 QTY PART # 0006 000 00 9 95 96 9 9 99 90 9 9 9 9 95 Service Parts List DESCRIPTION DECAL,SAFETY (NOT SHOWN) DECAL, SAFETY(NOT SHOWN) SPRING-LOCK REPAIR KIT JOINT AND SHAFT HALF ASSY W/ GUARD JOINT AND SHAFT HALF ASSY W/O GUARD JOINT AND TUBE HALF ASSY W/ GUARD JOINT AND TUBE HALF ASSY W/O GUARD YOKE, TUBE & SLIP SLEEVE OUTER GUARD INNER GUARD YOKE SPRING-LOCK YOKE ASSY R CROSS & BEARING KIT NYLON REPAIR KIT (NOT SHOWN) YOKE AND SHAFT (.00 X. RECT) 5 6 5 0 9 PTO SHAFT "SQUARE" PROFILE /6/0
DB600 PTO SHAFT - AW5 PART NO. 90 - (OBSOLETE) USED ON S/N: 0A0-09A5 (PART NO. 900 MAY BE USED TO REPLACE COMPLETE PTO SHAFT) ITEM 5 6 9 0 QTY PART # 60009 5005 9 95 96 9 9 99 950 95 0 PTO SHAFT "LEMON SHAPE" PROFILE Service Parts List DESCRIPTION DECAL,SAFETY (NOT SHOWN) DECAL, SAFETY(NOT SHOWN) YOKE, QUICK RELEASE -/ BORE CROSS & BEARING KIT PROFILE YOKE, INNER ROLL PIN, SPRING 0 X 0 MM YOKE, IMPLEMENT END -/'' BORE PROFILE YOKE, OUTER PLASTIC BEARING SET AW5 PTO SAFETY SHIELD SET AW5 5 6 /6/0 9
5 DB600 PTO SHAFT - 5R PART NO. 900 USED ON S/N: 0A0 AND A5 (PART NO. 906 MAY BE USED TO REPLACE COMPLETE PTO SHAFT ASSY) ITEM 5 6 9 0 5 QTY PART # 60009 0006 600 600 9 9 95 96 9 9 99 90 9 9 9 Service Parts List DESCRIPTION DECAL, SAFETY(NOT SHOWN) DECAL,SAFETY (NOT SHOWN) SAFETY SLIDE LOCK YOKE ASM. 5R CROSS KIT JOINT AND SHAFT HALF ASSY W/ GUARD JOINT AND SHAFT HALF ASSY W/O GUARD JOINT AND TUBE HALF ASSY W/ GUARD JOINT AND TUBE HALF ASSY W/O GUARD SSL/AUTO-LOK REPAIR KIT YOKE AND SHAFT (.9 SQUARE) OUTER GUARD GUARD REPAIR KIT (NOT SHOWN) INNER GUARD YOKE, TUBE & SLIP SLEEVE YOKE 5 6 0 9 PTO SHAFT "SQUARE" PROFILE 5//0 0
5 DB600 PTO SHAFT - 5R PART NO. 906 USED ON S/N: A6 - CURRENT ITEM 5 6 9 0 5 QTY PART # 600 99 600 600 9 95 96 9 9 9 99 90 950 95 9 Service Parts List DESCRIPTION DECAL, SAFETY(NOT SHOWN) DECAL,SAFETY (NOT SHOWN) SAFETY SLIDE LOCK YOKE ASM. 5R CROSS KIT JOINT AND SHAFT HALF ASSY W/ GUARD JOINT AND SHAFT HALF ASSY W/O GUARD JOINT AND TUBE HALF ASSY W/ GUARD JOINT AND TUBE HALF ASSY W/O GUARD SSL/AUTO-LOK REPAIR KIT YOKE AND SHAFT (.9 SQUARE) OUTER GUARD GUARD REPAIR KIT (NOT SHOWN) INNER GUARD YOKE, TUBE & SLIP SLEEVE YOKE 5 6 0 9 PTO SHAFT "SQUARE" PROFILE 5//0
R R. STOP MACHINE TO ADJUST & LUBRICATE. 9050 5 MAX 5 MAX 9069 90000. KEEP HANDS, FEET AND CLOTHING AWAY FROM POWER-DRIVEN PARTS.. IF MECHANISM BECOMES CLOGGED DISCONNECT POWER BEFORE CLEANING CAUTION.5" MAX 0.90" MIN CAUTION. KEEP ALL GAURDS IN PLACE. TRACTOR PTO HEIGHT AND ANGLE TO DEBRIS BLOWER MUST BE WITHIN SPECIFICATIONS. EXCEEDING THESE SPECIFICATIONS WILL SIGNIFICANTLY SHORTEN PTO SHAFT LIFE. 9000 90060 READ AND UNDERSTAND ALL INSTRUCTIONS AND SAFETY WARNINGS BEFORE OPERATING THIS EQUIPMENT. DO NOT OPERATE MACHINE IN THE VICINITY OF BYSTANDERS OR ANIMALS. NEVER DIRECT DISCHARGE TOWARDS BYSTANDERS OR OBJECTS SUCH AS CARS, BUILDINGS, ETC. ALWAYS WEAR A DUST MASK WHEN OPERATING IN DUSTY CONDITIONS. EYE AND EAR PROTECTION MUST BE WORN AT ALL TIMES. NEVER ALLOW PASENGERS ON THE MACHINE. KEEP HANDS, FEET AND CLOTHING AWAY FROM MOVING PARTS (ENTANGLEMENT CAN CAUSE SERIOUS INJURY OR DEATH). SHUT TRACTOR OFF AND ALLOW ALL MOVING PARTS TO COME TO A COMPLETE STOP BEFORE PERFORMING SERVICE OR REPAIR WORK. WARNING FAILURE TO FOLLOW SAFE OPERATING PROCEDURES CAN RESULT IN DEATH OR SERIOUS INJURY. 906 Failure to use hearing protection may cause permanent loss of hearing. WARNING 9000 9000 000 000 SHIELD HAS BEEN REMOVED! REPLACE PRIOR TO MACHINE OPERATION WARNING UNDER SHIELD DB600 - DECAL PLACEMENT 0/6/0 DECAL KIT 9009 9069 50006
NOTES
Harper Industries, Inc. 5 E. Highway 60 Harper, KS 605 Website: www.harperindustries.com Telephone: 60-96- Toll-Free: 00-5-0 Fax: 60-96-9 E-mail: info@harperindustries.com