Quality of Service Commands rate-limit. rate-limit {input output} [dscp dscp-value] [access-group [rate-limit] acl-index] bps

Quality of Service Commands rate-limit rate-limit To configure committed access rate (CAR) and distributed CAR (DCAR) policies, use the rate-limit interface configuration command. To remove the rate limit from the configuration, use the no form of this command. rate-limit {input output} [dscp dscp-value] [access-group [rate-limit] acl-index] bps burst-normal burst-max conform-action conform-action exceed-action exceed-action no rate-limit {input output} [dscp dscp-value] [access-group [rate-limit] acl-index] bps burst-normal burst-max conform-action conform-action exceed-action exceed-action Syntax Description input Applies this CAR traffic policy to packets received on this input interface. output Applies this CAR traffic policy to packets sent on this output interface. dscp (Optional) Allows the rate limit to be applied to any packet matching a specified differentiated services code point (DSCP). dscp-value (Optional) The DSCP number; values are 0 to 63. access-group (Optional) Applies this CAR traffic policy to the specified access list. rate-limit (Optional) The access list is a rate-limit access list. acl-index (Optional) Access list number. bps Average rate, in bits per second (bps). The value must be in increments of 8 kbps. burst-normal Normal burst size, in bytes. The minimum value is bps divided by 2000. burst-max Excess burst size, in bytes. conform-action conform-action Action to take on packets that conform to the specified rate limit. Specify one of the following keywords: continue Evaluates the next rate-limit command. drop Drops the packet. set-dscp-continue Sets the differentiated services code point (DSCP) (0 to 63) and evaluates the next rate-limit command. set-dscp-transmit Sends the DSCP and transmits the packet. set-mpls-exp-continue Sets the MPLS experimental bits (0 to 7) and evaluates the next rate-limit command. set-mpls-exp-transmit Sets the MPLS experimental bits (0 to 7) and sends the packet. set-prec-continue Sets the IP precedence (0 to 7) and evaluates the next rate-limit command. set-prec-transmit Sets the IP precedence (0 to 7) and sends the packet. set-qos-continue Sets the QoS group ID (1 to 99) and evaluates the next rate-limit command. set-qos-transmit Sets the QoS group ID (1 to 99) and sends the packet. transmit Sends the packet. QR-211

rate-limit Quality of Service Commands exceed-action exceed-action Action to take on packets that exceed the specified rate limit. Specify one of the following keywords: continue Evaluates the next rate-limit command. drop Drops the packet. set-dscp-continue Sets the DSCP (0 to 63) and evaluates the next rate-limit command. set-dscp-transmit Sends the DSCP and sends the packet. set-mpls-exp-continue Sets the MPLS experimental bits (0 to 7) and evaluates the next rate-limit command. set-mpls-exp-transmit Sets the MPLS experimental bits (0 to 7) and sends the packet. set-prec-continue Sets the IP precedence (0 to 7) and evaluates the next rate-limit command. set-prec-transmit Sets the IP precedence (0 to 7) and sends the packet. set-qos-continue Sets the QoS group ID (1 to 99) and evaluates the next rate-limit command. set-qos-transmit Sets the QoS group ID (1 to 99) and sends the packet. transmit Sends the packet. Defaults CAR and DCAR are disabled on the interface. Command Modes Interface configuration Command History Release Modification 11.1 CC This command was introduced. 12.1(5)T The conform and exceed actions were added for the MPLS experimental field. Usage Guidelines Use this command to configure your CAR policy on an interface. To specify multiple policies, enter this command once for each policy. Distributed CAR is supported only on Cisco 7000 series routers with an RSP7000 or Cisco 7500 series routers with VIP2-40 or greater interface processor. A VIP2-50 interface processor is strongly recommended when the aggregate line rate of the port adapters on the VIP is greater than DS3. A VIP2-50 interface processor is required for OC-3 rates. CAR and DCAR can only be used with IP traffic. Non-IP traffic is not rate limited. QR-212

Quality of Service Commands rate-limit CAR and DCAR can be configured on an interface or subinterface. However, CAR and DCAR are not supported on the Fast EtherChannel, tunnel, or PRI interfaces, nor on any interface that does not support Cisco Express Forwarding (CEF). CEF must be enabled on the interface before you configure CAR or DCAR. Policing Traffic with CAR CAR embodies a rate-limiting feature for policing traffic. When policing traffic with CAR, Cisco recommends the following values for the normal and extended burst parameters: normal burst = configured rate * (1 byte)/(8 bits) * 1.5 seconds extended burst = 2 * normal burst With the listed choices for parameters, extensive test results have shown CAR to achieve the configured rate. If the burst values are too low, then the achieved rate is often much lower than the configured rate. For more information about using CAR to police traffic, see the Policing with CAR section of the Policing and Shaping Overview in the Cisco IOS Quality of Service Configuration Guide, Release 12.2. Examples In the following example, the rate is limited by application: All World Wide Web traffic is sent. However, the MPLS experimental field for web traffic that conforms to the first rate policy is set to 5. For nonconforming traffic, the IP precedence is set to 0 (best effort). See the following commands in the example: rate-limit input rate-limit access-group 101 20000000 3750000 7500000 conform-action set-mpls-exp-transmit 5 exceed-action set-mpls-exp-transmit 0 access-list 101 permit tcp any any eq www FTP traffic is sent with an MPLS experimental field of 5 if it conforms to the second rate policy. If the FTP traffic exceeds the rate policy, it is dropped. See the following commands in the example: rate-limit input access-group 102 10000000 1875000 3750000 conform-action set-mpls-exp-transmit 5 exceed-action drop access-list 102 permit tcp any any eq ftp Any remaining traffic is limited to 8 Mbps, with a normal burst size of 1,500,000 bytes and an excess burst size of 3,000,000 bytes. Traffic that conforms is sent with an MPLS experimental field of 5. Traffic that does not conform is dropped. See the following command in the example: rate-limit input 8000000 1500000 3000000 conform-action set-mpls-exp-transmit 5 exceed-action drop Notice that two access lists are created to classify the web and FTP traffic so that they can be handled separately by the CAR feature: interface Hssi0/0/0 description 45Mbps to R2 rate-limit input rate-limit access-group 101 20000000 3750000 7500000 conform-action set-mpls-exp-transmit 5 exceed-action set-mpls-exp-transmit 0 rate-limit input access-group 102 10000000 1875000 3750000 conform-action set-mpls-exp-transmit 5 exceed-action drop rate-limit input 8000000 1500000 3000000 conform-action set-mpls-exp-transmit 5 exceed-action drop ip address 200.200.14.250 255.255.255.252! access-list 101 permit tcp any any eq www access-list 102 permit tcp any any eq ftp QR-213

rate-limit Quality of Service Commands In the following example, the MPLS experimental field is set and the packet is sent: interface FastEtheret1/1/0 rate-limit input 8000 1500 3000 access-group conform-action set mpls-exp-transmit 5 exceed-action set-mpls-exp-transmit 5 In the following example, any packet with a DSCP of 1 can apply the rate limit: interface pos6/1/0 rate-limit output dscp 1 8000 1500 3000 conform-action transmit exceed-action drop Related Commands Command Description access-list rate-limit Configures an access list for use with CAR policies. show access-lists rate-limit Displays information about rate-limit access lists. show interfaces rate-limit Displays information about CAR for an interface. show ip rsvp installed Displays RSVP-related installed filters and corresponding bandwidth information. QR-214

Quality of Service Commands send qdm message send qdm message To send a text message to all Quality Device Manager (QDM) clients, use the send qdm message EXEC command. send qdm [client client-id] message message-text Syntax Description client client-id message message-text (Optional) Specifies a QDM client to receive the message. (Optional) Specifies the QDM identification of the client that will receive the text message. Specifies that a message will be sent. The actual text of the message. Defaults This command has no default behavior or values. Command Modes EXEC Command History Release Release 12.1(1)E Release 12.1(5)T Modification This command was introduced. This command was integrated into Cisco IOS Release 12.1(5)T. Usage Guidelines Use the send qdm [client client-id] message message-text command to send a message to a specific QDM client. For example, entering the send qdm client 9 message hello command will send the message hello to client ID 9. Use the send qdm message message-text command to send a message to all QDM clients. For example, entering the send qdm message hello command sends the message hello to all open QDM clients. Examples The following example sends the text message how are you? to client ID 12: send qdm client 12 message how are you? The following example sends the text message how is everybody? to all QDM clients connected to the router: send qdm message how is everybody? Related Commands Command show qdm status Description Displays the status of connected QDM clients. QR-215

service-policy Quality of Service Commands service-policy To attach a policy map to an input interface or virtual circuit (VC), or an output interface or VC, to be used as the service policy for that interface or VC, use the service-policy interface configuration command. To remove a service policy from an input or output interface or input or output VC, use the no form of this command. service-policy {input output} policy-map-name no service-policy {input output} policy-map-name Syntax Description input output policy-map-name Attaches the specified policy map to the input interface or input VC. Attaches the specified policy map to the output interface or output VC. The name of a service policy map (created using the policy-map command) to be attached. Defaults No service policy is specified. Command Modes Interface configuration VC submode (for a standalone VC) Bundle-vc configuration (for ATM VC bundle members) Map-class configuration (for Frame Relay VCs) Command History Release 12.0(5)T 12.0(5)XE 12.0(7)S 12.1(1)E 12.1(2)T Modification This command was introduced. This command was integrated into Cisco IOS Release 12.0(5)XE. This command was integrated into Cisco IOS Release 12.0(7)S. This command was integrated into Cisco IOS Release 12.1(1)E. This command was integrated into Cisco IOS Release 12.l(2)T. This command was modified to enable low latency queueing (LLQ) on Frame Relay VCs. Usage Guidelines You can attach a single policy map to one or more interfaces or one or more VCs to specify the service policy for those interfaces or VCs. Currently a service policy specifies class-based weighted fair queueing (CBWFQ). The class policies comprising the policy map are then applied to packets that satisfy the class map match criteria for the class. To successfully attach a policy map to an interface or a VC, the aggregate of the configured minimum bandwidths of the classes comprising the policy map must be less than or equal to 75 percent of the interface bandwidth or the bandwidth allocated to the VC. QR-216

Quality of Service Commands service-policy To enable LLQ for Frame Relay (priority queueing (PQ)/CBWFQ), you must first enable Frame Relay Traffic Shaping (FRTS) on the interface using the frame-relay traffic-shaping command in interface configuration mode. You will then attach an output service policy to the Frame Relay VC using the service-policy command in map-class configuration mode. For a policy map to be successfully attached to an interface or ATM VC, the aggregate of the configured minimum bandwidths of the classes that make up the policy map must be less than or equal to 75 percent of the interface bandwidth or the bandwidth allocated to the VC. For a Frame Relay VC, the total amount of bandwidth allocated must not exceed the minimum committed information rate (CIR) configured for the VC less any bandwidth reserved by the frame-relay voice bandwidth or frame-relay ip rtp priority map-class commands. If not configured, the minimum CIR defaults to half of the CIR. Configuring CBWFQ on a physical interface is only possible if the interface is in the default queueing mode. Serial interfaces at E1 (2.048 Mbps) and below use WFQ by default. Other interfaces use FIFO by default. Enabling CBWFQ on a physical interface overrides the default interface queueing method. Enabling CBWFQ on an ATM permanent virtual circuit (PVC) does not override the default queueing method. Attaching a service policy and enabling CBWFQ on an interface renders ineffective any commands related to fancy queueing such as commands pertaining to fair queueing, custom queueing, priority queueing, and Weighted Random Early Detection (WRED). You can configure these features only after you remove the policy map from the interface. You can modify a policy map attached to an interface or a VC, changing the bandwidth of any of the classes comprising the map. Bandwidth changes that you make to an attached policy map are effective only if the aggregate of the bandwidth amounts for all classes comprising the policy map, including the modified class bandwidth, less than or equal to 75 percent of the interface bandwidth or the VC bandwidth. If the new aggregate bandwidth amount exceeds 75 percent of the interface bandwidth or VC bandwidth, the policy map is not modified. Examples The following example shows how to attache the service policy map called policy9 to data-link connection identifier (DLCI) 100 on output serial interface 1 and enables LLQ for Frame Relay: interface Serial1/0.1 point-to-point frame-relay interface-dlci 100 class fragment! map-class frame-relay fragment service-policy output policy9 The following example attaches the service policy map called policy9 to input serial interface 1: interface Serial1 service-policy input policy9 The following example attaches the service policy map called policy9 to the input PVC called cisco: pvc cisco 0/34 service-policy input policy9 vbr-nt 5000 3000 500 precedence 4-7 The following example attaches the policy called policy9 to output serial interface 1 to specify the service policy for the interface and enable CBWFQ on it: interface serial1 service-policy output policy9 QR-217

service-policy Quality of Service Commands The following example attaches the service policy map called policy9 to the output PVC called cisco: pvc cisco 0/5 service-policy output policy9 vbr-nt 4000 2000 500 precedence 2-3 Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. show frame-relay pvc Displays statistics about PVCs for Frame Relay interfaces. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map interface Displays the configuration of all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-218

Quality of Service Commands service-policy (class-map) service-policy (class-map) To attach a policy map to a class, use the service-policy class-map configuration command. To remove a service policy from a class, use the no form of this command. service-policy policy-map no service-policy Syntax Description policy-map The name of a service policy map (created using the policy-map command) to be attached. Defaults No service policy is specified. Command Modes Class-map configuration Command History Release 12.1(2)T Modification This command was introduced. Usage Guidelines You can attach a single policy map to one or more classes to specify the service policy for those classes. This command is only available for the output interface, which is assumed. Examples In the following example, three policy maps are defined cust1-classes, cust2-classes, and cust-policy. The policy maps cust1-classes and cust2-classes have three classes defined gold, silver, and bronze. For cust1-classes, gold is configured to use 50 percent of the bandwidth. Silver is configured to use 20 percent of the bandwidth, and bronze is configured to use 15 percent of the bandwidth. For cust2-classes, gold is configured to use 30 percent of the bandwidth. Silver is configured to use 15 percent of the bandwidth, and bronze is configured to use 10 percent of the bandwidth. The policy map cust-policy specifies average rate shaping of 384 kbps and assigns the service policy called cust1-classes to the policy map called cust1-classes. The policy map called cust-policy specifies peak rate shaping of 512 kbps and assigns the service policy called cust2-classes to the policy map called cust2-classes. To configure classes for cust1-classes, use the following commands: Router(config)# policy-map cust1-classes Router(config-pmap)# class gold Router(config-pmap-c)# bandwidth percent 50 Router(config-pmap)# class silver Router(config-pmap-c)# bandwidth percent 20 Router(config-pmap)# class bronze Router(config-pmap-c)# bandwidth percent 15 QR-219

service-policy (class-map) Quality of Service Commands To configure classes for cust2, use the following commands: Router(config)# policy-map cust2-classes Router(config-pmap)# class gold Router(config-pmap-c)# bandwidth percent 30 Router(config-pmap)# class silver Router(config-pmap-c)# bandwidth percent 15 Router(config-pmap)# class bronze Router(config-pmap-c)# bandwidth percent 10 To define the customer policy with cust1-classes and cust2-classes and QoS features, use the following commands: Router(config)# policy-map cust-policy Router(config-pmap)# class cust1 Router(config-pmap-c)# shape average 38400 Router(config-pmap-c)# service-policy cust1-classes Router(config-pmap)# class cust2 Router(config-pmap-c)# shape peak 51200 Router(config-pmap-c)# service-policy cust2-classes Router(config-pmap-c)# interface Serial 3/2 Router(config-if)# service out cust-policy Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. QR-220

Quality of Service Commands service-policy (policy-map class) service-policy (policy-map class) To use a service policy as a QoS policy within a policy map (called a hierarchical service policy), use the service-policy policy-map class configuration command. To disable a particular service policy as a QoS policy within a policy map, use the no form of this command. service-policy policy-map-name no service-policy policy-map-name Syntax Description policy-map-name Specifies the name of the predefined policy map to be used as a QoS policy. Defaults This command has no default behavior or values. Command Modes Policy-map class configuration Command History Release 12.1(2)E 12.1(5)T Modification This command was introduced. This command was integrated into Cisco IOS Release 12.1(5)T. Usage Guidelines This command is used to create hierarchical service policies in policy-map class configuration mode. This command is different from the service-policy [input output] policy-map-name command used in interface configuration mode. The purpose of the service-policy [input output] policy-map-name is to attach service policies to interfaces. The child policy is the previously defined service policy that is being associated with the new service policy through the use of the service-policy command. The new service policy using the preexisting service policy is the parent policy. This command has the following restrictions: The set command is not supported on the child policy. The priority command can be used in either the parent or the child policy, but not both policies simultaneously. The shape command cannot be used in child policies (for instance, in hierarchical shaping) on a subinterface. The fair-queue command cannot be defined in the parent policy. If the bandwidth command is used in the child policy, the bandwidth command must also be used in the parent policy. The one exception is for policies using the default class. QR-221

service-policy (policy-map class) Quality of Service Commands Examples The following example creates a hierarchical service policy in the service policy called parent: Router(config)# policy-map child Router(config-pmap)# class voice Router(config-pmap-c)# priority 50 Router(config)# policy-map parent Router(config-pmap)# class class-default Router(config-pmap-c)# shape average 10000000 Router(config-pmap-c)# service-policy child FRF.11 and FRF.12 configurations on a Versatile Interface Processor (VIP)-enabled Cisco 7500 series router often require a hierarchical service policy for configuration. A hierarchical service policy for FRF.11 and FRF.12 requires the following elements: 1. A traffic class that uses the Voice over Frame Relay (VoFR) protocol as the only match criterion. 2. A traffic policy that insures low latency queueing (LLQ), which is achieved using the priority command, for all VoFR protocol traffic 3. A traffic policy that defines the shaping parameters and includes the elements listed in element 2. Element 3 can only be fulfilled through the use of a hierarchical service policy, which is configured using the service-policy command. In the following example, element 1 is configured in the traffic class called frf, element 2 is configured in the traffic policy called llq, and element 3 is configured in the traffic policy called llq-shape. Router(config)# class-map frf Router(config-cmap)# match protocol vofr Router(config-cmap)# exit Router(config)# policy-map llq Router(config-pmap)# class frf Router(config-pmap-c)# priority 2000 Router(config-pmap-c)# exit Router(config-pmap)# exit Router(config)# policy-map llq-shape Router(config-pmap)# class class-default Router(config-pmap-c)# shape average 1000 128000 Router(config-pmap-c)# service-policy llq The final step in using a hierarchical service policy for FRF.11 and FRF.12 is using the service policy in map-class configuration mode. In the following example, the traffic policy called llq-shape is attached to the map class called frag: Router(config)# map-class frame-relay frag Router(config-map-class)# frame-relay fragment 40 Router(config-map-class)# service-policy llq-shape QR-222

Quality of Service Commands service-policy (policy-map class) Related Commands Command Description bandwidth (policy-map class) Specifies or modifies the bandwidth allocated for a class belonging to a policy map. fair-queue Specifies the number of queues to be reserved for use by a traffic class. policy-map Specifies the name of the service policy to configure. priority Gives priority to a class of traffic belonging to a policy map. service-policy Specifies the name of the service policy to be attached to the interface. shape Specifies average or peak rate traffic shaping. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map interface Displays the configuration of all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-223

set atm-clp Quality of Service Commands set atm-clp To set the cell loss priority (CLP) bit setting when configuring a policy map, use the set atm-clp policy-map class configuration command. set atm-clp Syntax Description This command has no arguments or keywords. Defaults The CLP bit is automatically set to 0 when Cisco routers convert IP packets into ATM cells for transmission through Multiprotocol Label Switching (MPLS)-aware ATM networks. Command Modes Policy-map class Command History Release 12.0(7)S 12.1(5)T Modification This command was introduced. This command was integrated into Cisco IOS Release 12.1(5)T. Usage Guidelines To disable this command, remove the service policy from the interface. To use the set atm-clp command, you must have one of the following adapters: the Enhanced ATM Port Adapter (PA-A3), the ATM Inverse Multiplexer over ATM Port Adapter with 8 T1 Ports (PA-A3-8T1IMA), or the ATM Inverse Multiplexer over ATM Port Adapter with 8 E1 Ports (PA-A3-8E1IMA). Therefore, the set atm-clp command is not supported on any platform that does not support these adapters. For more information, refer to the documentation for your specific router. A policy map containing the set atm-clp command can be attached as an output policy only. The set atm-clp command does not support packets that originate from the router. Examples The following example illustrates a CLP bit set using the set atm-clp command in the policy map: Router(config)# class-map ip-prec Router(config-cmap)# match ip precedence 0 1 Router(config-cmap)# exit Router(config)# policy-map atm-clp-set Router(config-pmap)# class ip-prec Router(config-pmap-c)# set atm-clp Router(config-pmap-c)# exit Router(config-pmap)# exit Router(config)# interface atm 1/0/0 Router(config)# service-policy output bear QR-224

Quality of Service Commands set atm-clp Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. show atm pvc Displays information about the PVCs on an interface. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. QR-225

set cos Quality of Service Commands set cos To set the Layer 2 class of service (CoS) value of an outgoing packet, use the set cos policy-map class configuration command. To remove a specific CoS value setting, use the no form of this command: set cos cos-value no set cos cos-value Syntax Description cos-value Specific IEEE 802.1Q CoS value from 0 to 7. Defaults Disabled Command Modes Policy-map class configuration Command History Release 12.1(5)T Modification This command was introduced. Usage Guidelines CoS packet marking is only supported in the Cisco Express Forwarding (CEF)-switching path. The set cos command should be used by a router if a user wants to mark a packet that is being sent to a switch. Switches can leverage Layer 2 header information, including a CoS value marking. The set cos command can be used only in service policies that are attached in the output direction of an interface. Packets entering an interface cannot be set with a CoS value. The match cos and set cos commands can be used together to allow routers and switches to interoperate and provide QoS based on the CoS markings. Layer 2 to Layer 3 mapping can be configured by matching on the CoS value because switches already can match and set CoS values. If a packet that needs to be marked to differentiate user-defined QoS services is leaving a router and entering a switch, the router should set the CoS value of the packet because the switch can process the Layer 2 header. QR-226

Quality of Service Commands set cos Examples In the following example, the policy map called cos-set is created to assign different CoSs for different types of traffic. This example assumes that the class maps called voice and video-data have already been created. Router(config)# policy-map cos-set Router(config-pmap)# class voice Router(config-pmap-c)# set cos 1 Router(config-pmap-c)# exit Router(config-pmap)# class video-data Router(config-pmap-c)# set cos 2 Router(config-pmap-c)# exit Router(config-pmap)# exit This command is applied when you create a service policy in QoS policy-map configuration mode. This service policy is not yet attached to an interface. For information on attaching a service policy to an interface, refer to the Modular Quality of Service Command-Line Interface chapter of the Cisco IOS Quality of Service Solutions Configuration Guide. Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. service-policy Attaches a policy map to an input interface or VC, or an output interface or VC, to be used as the service policy for that interface or VC. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map class Displays the configuration for the specified class of the specified policy map. show policy-map interface Displays the configuration of all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-227

set ip dscp Quality of Service Commands set ip dscp To mark a packet by setting the IP differentiated services code point (DSCP) in the type of service (ToS) byte, use the set ip dscp QoS policy-map configuration command. To remove a previously set IP DSCP, use the no form of this command. set ip dscp ip-dscp-value no set ip dscp ip-dscp-value Syntax Description ip-dscp-value A number from 0 to 63 that sets the IP DSCP value. Reserved keywords EF (expedited forwarding), AF11 (assured forwarding class AF11), and AF12 (assured forwarding class AF12) can be specified instead of numeric values. Defaults This command has no default behavior or values. Command Modes QoS policy-map configuration Command History Release 12.0(5)XE 12.1(2)T Modification This command was introduced. This command was integrated into Cisco IOS Release 12.l(2)T. This command was enhanced to include reserved keywords EF, AF11, and AF12 instead of numeric values. Usage Guidelines Once the IP DSCP bit is set, other QoS services can then operate on the bit settings. You cannot mark a packet by the IP precedence with the set ip precedence command and mark the same packet with an IP DSCP value by entering the set ip dscp command. The network gives priority (or some type of expedited handling) to marked traffic. Typically, you set IP precedence at the edge of the network (or administrative domain); data then is queued based on the precedence. Weighted fair queueing (WFQ) can speed up handling for high-precedence traffic at congestion points. Weighted Random Early Detection (WRED) ensures that high-precedence traffic has lower loss rates than other traffic during times of congestion. Reserved keywords EF, AF11, and AF12 can be specified instead of numeric values. QR-228

Quality of Service Commands set ip dscp Examples In the following example, the IP DSCP ToS byte is set to 8 in the policy map called policy1: Router(config)# policy-map policy1 Router(config-pmap)# class class1 Router(config-pmap-c)# set ip dscp 8 All packets that satisfy the match criteria of class1 are marked with the IP DSCP value of 8. How packets marked with the IP DSCP value of 8 are treated is determined by the network configuration. After you configure the settings shown for voice packets at the edge, all intermediate routers are then configured to provide low latency treatment to the voice packets, as follows: Router(config)# class-map voice Router(config-cmap)# match ip dscp ef Router(config)# policy qos-policy Router(config-pmap)# class voice Router(config-pmap-c)# priority 24 The set ip dscp command is applied when you create a service policy in QoS policy-map configuration mode. This service policy is not yet attached to an interface. For information on attaching a service policy to an interface, refer to the Modular Quality of Service Command-Line Interface chapter of the Cisco IOS Quality of Service Solutions Configuration Guide. Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. service-policy Attaches a policy map to an input interface or VC, or an output interface or VC, to be used as the service policy for that interface or VC. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map class Displays the configuration for the specified class of the specified policy map. show policy-map interface Displays the configuration of all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-229

set ip precedence (policy-map) Quality of Service Commands set ip precedence (policy-map) To set the precedence value in the IP header, use the set ip precedence QoS policy-map configuration command. To leave the precedence value at the current setting, use the no form of this command. set ip precedence ip-precedence-value no set ip precedence Syntax Description ip-precedence-value A number from 0 to 7 that sets the precedence bit in the IP header. Defaults This command is disabled by default. Command Modes QoS policy-map configuration Command History Release Modification 11.0 This command was introduced. 12.0(5)XE This command was integrated into Cisco IOS Release 12.0(5)XE. This command was introduced in the Modular Quality of Service Command-Line Interface (MQC) feature. Usage Guidelines Once the IP precedence bits are set, other QoS services such as weighted fair queueing (WFQ) and Weighted Random Early Detection (WRED) then operate on the bit settings. The network gives priority (or some type of expedited handling) to marked traffic through the application of WFQ or WRED at points downstream in the network. Typically, you set IP Precedence at the edge of the network (or administrative domain); data then is queued based on the precedence. WFQ can speed up handling for certain precedence traffic at congestion points. WRED can ensure that certain precedence traffic has lower loss rates than other traffic during times of congestion. Examples The following example sets the IP Precedence to 5 for packets that satisfy the match criteria of the class map called class1: Router(config)# policy-map policy1 Router(config-pmap)# class class1 Router(config-pmap-c)# set ip precedence 5 All packets that satisfy the match criteria of class1 are marked with the IP Precedence value of 5. How packets marked with the IP Precedence value of 5 are treated is determined by the network configuration. The set ip precedence command is applied when you create a service policy in QoS policy-map configuration mode. This service policy is not yet attached to an interface or to an ATM virtual circuit. For information on attaching a service policy to an interface, refer to the Modular Quality of Service Command-Line Interface chapter of the Cisco IOS Quality of Service Solutions Configuration Guide. QR-230

Quality of Service Commands set ip precedence (policy-map) Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. service-policy Attaches a policy map to an input interface or VC, or an output interface or VC, to be used as the service policy for that interface or VC. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map interface Displays the configuration for all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-231

set ip precedence (route-map) Quality of Service Commands set ip precedence (route-map) To set the precedence value (and an optional IP number or IP name) in the IP header, use the set ip precedence route-map configuration command. To leave the precedence value unchanged, use the no form of this command. set ip precedence [number name] no set ip precedence Syntax Description number name (Optional) A number or name that sets the precedence bits in the IP header. The values for the number argument and the corresponding name argument are listed in Table 16, from least to most important. Defaults This command is disabled by default. Command Modes Route-map configuration Command History Release Modification 11.0 This command was introduced. Usage Guidelines Table 16 lists the values for the number argument and the corresponding name argument for precedence values in the IP header. They are listed from least to most important. Table 16 Number and Name Values for IP Precedence Number Name 0 routine 1 priority 2 immediate 3 flash 4 flash-override 5 critical 6 internet 7 network You can set the precedence using either a number or the corresponding name. Once the IP Precedence bits are set, other QoS services such as weighted fair queueing (WFQ) and Weighted Random Early Detection (WRED) then operate on the bit settings. QR-232

Quality of Service Commands set ip precedence (route-map) The network gives priority (or some type of expedited handling) to marked traffic through the application of WFQ or WRED at points downstream in the network. Typically, you set IP Precedence at the edge of the network (or administrative domain); data then is queued based on the precedence. WFQ can speed up handling for certain precedence traffic at congestion points. WRED can ensure that certain precedence traffic has lower loss rates than other traffic during times of congestion. The mapping from arguments such as routine and priority to a precedence value is useful only in some instances. That is, the use of the precedence bit is evolving. You can define the meaning of a precedence value by enabling other features that use the value. In the case of the high-end Internet QoS available from Cisco, IP Precedences can be used to establish classes of service that do not necessarily correspond numerically to better or worse handling in the network. Use the route-map (IP) global configuration command with the match and set route-map configuration commands to define the conditions for redistributing routes from one routing protocol into another, or for policy routing. Each route-map command has an associated list of match and set commands. The match commands specify the match criteria the conditions under which redistribution or policy routing is allowed for the current route-map command. The set commands specify the set actions the particular redistribution or policy routing actions to perform if the criteria enforced by the match commands are met. The no route-map command deletes the route map. The set route-map configuration commands specify the redistribution set actions to be performed when all of the match criteria of a route map are met. Examples The following example sets the IP Precedence to 5 (critical) for packets that pass the route map match: interface serial 0 ip policy route-map texas route-map texas match length 68 128 set ip precedence 5 Related Commands Command Description fair-queue (WFQ) Enables WFQ for an interface. ip policy route-map Identifies a route map to use for policy routing on an interface. random-detect dscp Changes the minimum and maximum packet thresholds for the DSCP value. rate-limit Configures CAR and DCAR policies. route-map (IP) Defines the conditions for redistributing routes from one routing protocol into another, or enables policy routing. traffic-shape adaptive Configures a Frame Relay subinterface to estimate the available bandwidth when BECN signals are received. traffic-shape fecn-adapt Replies to messages with the FECN bit (which are set with TEST RESPONSE messages with the BECN bit set). traffic-shape group Enables traffic shaping based on a specific access list for outbound traffic on an interface. traffic-shape rate Enables traffic shaping for outbound traffic on an interface. QR-233

set ip qos-group Quality of Service Commands set ip qos-group To set a group ID that can be used later to classify packets, use the set ip qos-group route-map configuration command. To remove the group ID, use the no form of this command. set ip qos-group group-id no set ip qos-group group-id Syntax Description group-id Group ID number in the range from 0 to 99. Defaults This command is disabled by default. No group ID is specified. Command Modes Route-map configuration Command History Release Modification 11.1 CC This command was introduced. Usage Guidelines This command allows you to set a group ID in the routing table that can be used later to classify packets into QoS groups based on prefix, autonomous system, and community string. These packets can then be rate limited or weighted fairly in the queue based on the QoS group ID. To display QoS group information, use the show ip cef command. Examples The following example sets the QoS group to 1 for all packets that match community 1. These packets are then rate limited based on the QoS group ID. configure terminal route-map precedence-map permit 10 match community 1 set ip qos-group 1 interface hssi0/0/0 bgp-policy source qos-group end QR-234

Quality of Service Commands set ip tos (route-map) set ip tos (route-map) To set the type of service (TOS) bits in the header of an IP packet, use the set ip tos command in route-map configuration mode. To leave the TOS bits unchanged, use the no form of this command. set ip tos [number] no set ip tos Syntax Description number (Optional) A number from 0 to 15 that sets the TOS bits in the IP header. See Table 17 for more information. Defaults Disabled Command Modes Route-map configuration Command History Release Modification 11.2 This command was introduced. Usage Guidelines This command allows you to set four bits in the TOS byte header. Table 17 shows the format of the four bits in binary form. Table 17 TOS Bits and Description T3 T2 T1 T0 Description 0 0 0 0 0 normal forwarding 0 0 0 1 1 minimum monetary cost 0 0 1 0 2 maximum reliability 0 1 0 0 4 maximum throughput 1 0 0 0 8 minimum delay The T3 bit sets the delay. Setting T3 to 0 equals normal delay, and setting it to 1 equals low delay. The T2 bit sets the throughput. Setting this bit to 0 equals normal throughput, and setting it to 1 equals maximum throughput. Similarly, the T1 and T0 bits set reliability and cost, respectively. Therefore, as an example, if you want to set a packet with the following requirements: minimum delay T3 = 1 normal throughout T2= 0 normal reliability T1=0 minimum monetary cost T0=1 QR-235

set ip tos (route-map) Quality of Service Commands You would set the TOS to 9, which is 1001 in binary format. Use the route-map (IP) global configuration command with the match and set route-map configuration commands to define the conditions for redistributing routes from one routing protocol into another, or for policy routing. Each route-map command has an associated list of match and set commands. The match commands specify the match criteria the conditions under which redistribution or policy routing is allowed for the current route-map command. The set commands specify the set actions the particular redistribution or policy routing actions to perform if the criteria enforced by the match commands are met. The no route-map command deletes the route map. The set route-map configuration commands specify the redistribution set actions to be performed when all of the match criteria of a route map are met. Examples The following example sets the IP TOS bits to 8 (minimum delay as shown in Table 17) for packets that pass the route-map match: interface serial 0 ip policy route-map texas! route-map texas match length 68 128 set ip tos 8! Related Commands Command Description ip policy route-map Identifies a route map to use for policy routing on an interface. route-map (IP) Defines the conditions for redistributing routes from one routing protocol into another, or enables policy routing. QR-236

Quality of Service Commands set qos-group set qos-group To set a group ID that can be used later to classify packets, use the set qos-group QoS policy-map configuration command. To remove the group ID, use the no form of this command. set qos-group group-id no set qos-group group-id Syntax Description group-id Group ID number in the range from 0 to 99. Defaults This command is disabled by default. No group ID is specified. Command Modes QoS policy-map configuration Command History Release Modification 11.1 CC This command was introduced. 12.0(5)XE This command was integrated into Cisco IOS Release 12.0(5)XE. This command was included in the Modular Quality of Service Command-Line Interface (MQC) feature. Usage Guidelines This command allows you to associate a group ID with a packet. The group ID can be used later to classify packets into QoS groups based on prefix, autonomous system, and community string. To display QoS group information, use the show ip cef command. Examples The following example sets the QoS group to 1 for all packets that match the class map called class1. These packets are then rate limited based on the QoS group ID. Router(config)# policy-map policy1 Router(config-pmap)# class class1 Router(config-pmap-c)# set qos-group 1 The set qos-group command is applied when you create a service policy in QoS policy-map configuration mode. This service policy is not yet attached to an interface or an ATM virtual circuit. For information on attaching a service policy to an interface, refer to the Modular Quality of Service Command-Line Interface chapter of the Cisco IOS Quality of Service Solutions Configuration Guide. QR-237

set qos-group Quality of Service Commands Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to one or more interfaces to specify a service policy. service-policy Attaches a policy map to an input interface or VC, or an output interface or VC, to be used as the service policy for that interface or VC. show policy-map Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. show policy-map interface Displays the configuration of all classes configured for all service policies on the specified interface or displays the classes for the service policy for a specific PVC on the interface. QR-238