Chapter 14. Oscillations. PowerPoint Lectures for College Physics: A Strategic Approach, Second Edition Pearson Education, Inc.

Similar documents
Practice Test SHM with Answers

Simple Harmonic Motion(SHM) Period and Frequency. Period and Frequency. Cosines and Sines

Oscillations: Mass on a Spring and Pendulums

Simple Harmonic Motion

AP Physics C. Oscillations/SHM Review Packet

AP1 Oscillations. 1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false?

226 Chapter 15: OSCILLATIONS

Spring Simple Harmonic Oscillator. Spring constant. Potential Energy stored in a Spring. Understanding oscillations. Understanding oscillations

Solution: F = kx is Hooke s law for a mass and spring system. Angular frequency of this system is: k m therefore, k

Physics 231 Lecture 15

both double. A. T and v max B. T remains the same and v max doubles. both remain the same. C. T and v max

AP Physics - Chapter 8 Practice Test

Physics 1120: Simple Harmonic Motion Solutions

1) The time for one cycle of a periodic process is called the A) wavelength. B) period. C) frequency. D) amplitude.

Unit 3 Work and Energy Suggested Time: 25 Hours

Prelab Exercises: Hooke's Law and the Behavior of Springs

Physics 41 HW Set 1 Chapter 15

PENDULUM PERIODS. First Last. Partners: student1, student2, and student3

HOOKE S LAW AND SIMPLE HARMONIC MOTION

PHYS 211 FINAL FALL 2004 Form A

Simple Harmonic Motion Experiment. 1 f

Sample lab procedure and report. The Simple Pendulum

Lesson 11. Luis Anchordoqui. Physics 168. Tuesday, December 8, 15

PHYS 2425 Engineering Physics I EXPERIMENT 9 SIMPLE HARMONIC MOTION

A) F = k x B) F = k C) F = x k D) F = x + k E) None of these.

PHYS 101-4M, Fall 2005 Exam #3. MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

ELASTIC FORCES and HOOKE S LAW

Exercises on Oscillations and Waves

Chapter 8: Potential Energy and Conservation of Energy. Work and kinetic energy are energies of motion.

EXPERIMENT 2 Measurement of g: Use of a simple pendulum

FXA UNIT G484 Module Simple Harmonic Oscillations 11. frequency of the applied = natural frequency of the

Chapter 6 Work and Energy

HOOKE S LAW AND OSCILLATIONS

Tennessee State University

physics 1/12/2016 Chapter 20 Lecture Chapter 20 Traveling Waves

Chapter 3.8 & 6 Solutions

Energy transformations

Work, Energy and Power Practice Test 1

Lesson 39: Kinetic Energy & Potential Energy

Chapter 9. is gradually increased, does the center of mass shift toward or away from that particle or does it remain stationary.

Physics 101 Hour Exam 3 December 1, 2014

9. The kinetic energy of the moving object is (1) 5 J (3) 15 J (2) 10 J (4) 50 J

If you put the same book on a tilted surface the normal force will be less. The magnitude of the normal force will equal: N = W cos θ

16.2 Periodic Waves Example:

Copyright 2011 Casa Software Ltd.

LAB 6 - GRAVITATIONAL AND PASSIVE FORCES

LAB 6: GRAVITATIONAL AND PASSIVE FORCES

Lab 8: Ballistic Pendulum

Determination of Acceleration due to Gravity

SOLUTIONS TO CONCEPTS CHAPTER 15

C B A T 3 T 2 T What is the magnitude of the force T 1? A) 37.5 N B) 75.0 N C) 113 N D) 157 N E) 192 N

Physics 2A, Sec B00: Mechanics -- Winter 2011 Instructor: B. Grinstein Final Exam

Oscillations. Vern Lindberg. June 10, 2010

Standing Waves on a String

AP Physics C Fall Final Web Review

Work, Power, Energy Multiple Choice. PSI Physics. Multiple Choice Questions

Physics 125 Practice Exam #3 Chapters 6-7 Professor Siegel

Objective: Work Done by a Variable Force Work Done by a Spring. Homework: Assignment (1-25) Do PROBS # (64, 65) Ch. 6, + Do AP 1986 # 2 (handout)

Applications of Second-Order Differential Equations

The Physics of Guitar Strings

More Quadratic Equations

Review Assessment: Lec 02 Quiz

KE =? v o. Page 1 of 12

Freely Falling Objects

Sound and stringed instruments

Chapter 5 Using Newton s Laws: Friction, Circular Motion, Drag Forces. Copyright 2009 Pearson Education, Inc.

Pendulum Force and Centripetal Acceleration

PHYSICS HIGHER SECONDARY FIRST YEAR VOLUME - II. Revised based on the recommendation of the Textbook Development Committee. Untouchability is a sin

Curso Física Básica Experimental I Cuestiones Tema IV. Trabajo y energía.

Ch 7 Kinetic Energy and Work. Question: 7 Problems: 3, 7, 11, 17, 23, 27, 35, 37, 41, 43

In order to describe motion you need to describe the following properties.

Displacement (x) Velocity (v) Acceleration (a) x = f(t) differentiate v = dx Acceleration Velocity (v) Displacement x

AP1 Dynamics. Answer: (D) foot applies 200 newton force to nose; nose applies an equal force to the foot. Basic application of Newton s 3rd Law.

Problem Set 5 Work and Kinetic Energy Solutions

Sample Questions for the AP Physics 1 Exam

Rotation: Moment of Inertia and Torque

Physics 9e/Cutnell. correlated to the. College Board AP Physics 1 Course Objectives

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

CHAPTER 6 WORK AND ENERGY

Chapter 15, example problems:

VELOCITY, ACCELERATION, FORCE

Candidate Number. General Certificate of Education Advanced Level Examination June 2012

Work, Energy & Momentum Homework Packet Worksheet 1: This is a lot of work!

WORK DONE BY A CONSTANT FORCE

Experiment 7 ~ Conservation of Linear Momentum

Lecture 17. Last time we saw that the rotational analog of Newton s 2nd Law is

Experiment 9. The Pendulum

Practice Exam Three Solutions

Candidate Number. General Certificate of Education Advanced Level Examination June 2014

Steps to Solving Newtons Laws Problems.

Weight The weight of an object is defined as the gravitational force acting on the object. Unit: Newton (N)

Pendulum Investigations. Level A Investigations. Level B Investigations

Chapter 9. particle is increased.

ANALYTICAL METHODS FOR ENGINEERS

Determination of g using a spring

F N A) 330 N 0.31 B) 310 N 0.33 C) 250 N 0.27 D) 290 N 0.30 E) 370 N 0.26

SOLID MECHANICS DYNAMICS TUTORIAL NATURAL VIBRATIONS ONE DEGREE OF FREEDOM

PHY231 Section 2, Form A March 22, Which one of the following statements concerning kinetic energy is true?

GENERAL SCIENCE LABORATORY 1110L Lab Experiment 3: PROJECTILE MOTION

Transcription:

Chapter 14 Oscillations PowerPoint Lectures for College Physics: A Strategic Approach, Second Edition

14 Oscillations

Reading Quiz 1. The type of function that describes simple harmonic motion is A. linear B. exponential C. quadratic D. sinusoidal E. inverse

Answer 1. The type of function that describes simple harmonic motion is A. linear B. exponential C. quadratic D. sinusoidal E. inverse

Reading Quiz 2. A mass is bobbing up and down on a spring. If you increase the amplitude of the motion, how does this affect the time for one oscillation? A. The time increases. B. The time decreases. C. The time does not change.

Answer 2. A mass is bobbing up and down on a spring. If you increase the amplitude of the motion, how does this affect the time for one oscillation? A. The time increases. B. The time decreases. C. The time does not change.

Reading Quiz 3. If you drive an oscillator, it will have the largest amplitude if you drive it at its frequency. A. special B. positive C. natural D. damped E. pendulum

Answer 3. If you drive an oscillator, it will have the largest amplitude if you drive it at its frequency. A. special B. positive C. natural D. damped E. pendulum

Equilibrium and Oscillation

Linear Restoring Forces and Simple Harmonic Motion Simple harmonic motion (SHM) is the motion of an object subject to a force that is proportional to the object's displacement. One example of SHM is the motion of a mass attached to a spring. In this case, the relationship between the spring force and the displacement is given by Hooke's Law, F = -kx, where k is the spring constant, x is the displacement from the equilibrium length of the spring, and the minus sign indicates that the force opposes the displacement.

Linear Restoring Forces and Simple Harmonic Motion

Frequency and Period The frequency of oscillation depends on physical properties of the oscillator; it does not depend on the amplitude of the oscillation.

Sinusoidal Relationships

Each dimension of circular motion is a sinusoidal funtion. Animation of sine and cosine

Mathematical Description of Simple Harmonic Motion

What is the largest value cos(2pft) can ever have? A. 0 B. 1 C. 2pft D. E. ½

What is the largest value cos(2pft) can ever have? A. 0 B. 1 C. 2pft D. E. ½

What is the largest value sin(2pft) can ever have? A. 0 B. 1 C. 2pft D. E. ½

What is the largest value sin(2pft) can ever have? A. 0 B. 1 C. 2pft D. E. ½

Maximum displacement, velocity and acceleration What is the largest displacement possible? A. 0 B. A C. 2pft D. E. ½ A

Maximum displacement, velocity and acceleration What is the largest displacement possible? A. 0 B. A C. 2pft D. E. ½ A

Maximum displacement, velocity and acceleration What is the largest velocity possible? A. 0 B. 2pf C. 2Apf D. Apf E.

Maximum displacement, velocity and acceleration What is the largest velocity possible? A. 0 B. 2pf C. 2Apf D. Apf E.

Maximum displacement, velocity and acceleration What is the largest acceleration possible? A. 0 B. 2A(pf) 2 C. 4p 2 Af 2 D. E. 2Apf

Maximum displacement, velocity and acceleration What is the largest acceleration possible? A. 0 B. 2A(pf) 2 C. 4p 2 Af 2 D. E. 2Apf

Energy in Simple Harmonic Motion As a mass on a spring goes through its cycle of oscillation, energy is transformed from potential to kinetic and back to potential.

Solving Problems

Equations

Additional Example Problem Walter has a summer job babysitting an 18 kg youngster. He takes his young charge to the playground, where the boy immediately runs to the swings. The seat of the swing the boy chooses hangs down 2.5 m below the top bar. Push me, the boy shouts, and Walter obliges. He gives the boy one small shove for each period of the swing, in order keep him going. Walter earns $6 per hour. While pushing, he has time for his mind to wander, so he decides to compute how much he is paid per push. How much does Walter earn for each push of the swing?

Additional Example Problem Walter has a summer job babysitting an 18 kg youngster. He takes his young charge to the playground, where the boy immediately runs to the swings. The seat of the swing the boy chooses hangs down 2.5 m below the top bar. Push me, the boy shouts, and Walter obliges. He gives the boy one small shove for each period of the swing, in order keep him going. Walter earns $6 per hour. While pushing, he has time for his mind to wander, so he decides to compute how much he is paid per push. How much does Walter earn for each push of the swing? T = 2p (l/g) = 3.17 s 3600 s/hr (1 push/3.17s) = 1136 pushes/ hr $6/hr (1hr/1136 pushes) = $0.0053 / push Or half a penny per push!

Checking Understanding A series of pendulums with different length strings and different masses is shown below. Each pendulum is pulled to the side by the same (small) angle, the pendulums are released, and they begin to swing from side to side. 25 Rank the frequencies of the five pendulums, from highest to lowest. A. A E B D C B. D A C B E C. A B C D E D. B E C A D

Answer A series of pendulums with different length strings and different masses is shown below. Each pendulum is pulled to the side by the same (small) angle, the pendulums are released, and they begin to swing from side to side. 25 Rank the frequencies of the five pendulums, from highest to lowest. A. A E B D C B. D A C B E C. A B C D E D. B E C A D f = 1/2p (g/l) Frequency is proportional to the inverse of the length. So longer has a lower frequency

Example Problem We think of butterflies and moths as gently fluttering their wings, but this is not always the case. Tomato hornworms turn into remarkable moths called hawkmoths whose flight resembles that of a hummingbird. To a good approximation, the wings move with simple harmonic motion with a very high frequency about 26 Hz, a high enough frequency to generate an audible tone. The tips of the wings move up and down by about 5.0 cm from their central position during one cycle. Given these numbers, A. What is the maximum velocity of the tip of a hawkmoth wing? B. What is the maximum acceleration of the tip of a hawkmoth wing?

Example Problem We think of butterflies and moths as gently fluttering their wings, but this is not always the case. Tomato hornworms turn into remarkable moths called hawkmoths whose flight resembles that of a hummingbird. To a good approximation, the wings move with simple harmonic motion with a very high frequency about 26 Hz, a high enough frequency to generate an audible tone. The tips of the wings move up and down by about 5.0 cm from their central position during one cycle. Given these numbers, A. What is the maximum velocity of the tip of a hawkmoth wing? B. What is the maximum acceleration of the tip of a hawkmoth wing? v max = 2pfA = 2 p 26Hz 0.05m = 8.17 m/s a max = A (2pf) 2 = (2 p 26Hz) 2 0.05m = 1334 m/s 2

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: 1. At which of the above times is the displacement zero? 2. At which of the above times is the velocity zero? 3. At which of the above times is the acceleration zero? 4. At which of the above times is the kinetic energy a maximum? 5. At which of the above times is the potential energy a maximum? 6. At which of the above times is kinetic energy being transformed to potential energy? 7. At which of the above times is potential energy being transformed to kinetic energy?

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the displacement zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the displacement zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the velocity zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the velocity zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the acceleration zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: Without ball At which of the above times is the acceleration zero? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the kinetic energy a maximum? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the kinetic energy a maximum? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the potential energy a maximum? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is the potential energy a maximum? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is kinetic energy being transformed to potential energy? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is kinetic energy being transformed to potential energy? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is potential energy being transformed to kinetic energy? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A ball on a spring is pulled down and then released. Its subsequent motion appears as follows: At which of the above times is potential energy being transformed to kinetic energy? A. C, G B. A, E, I C. B, F D. D, H

Example Problem A pendulum is pulled to the side and released. Its subsequent motion appears as follows: 1. At which of the above times is the displacement zero? 2. At which of the above times is the velocity zero? 3. At which of the above times is the acceleration zero? 4. At which of the above times is the kinetic energy a maximum? 5. At which of the above times is the potential energy a maximum? 6. At which of the above times is kinetic energy being transformed to potential energy? 7. At which of the above times is potential energy being transformed to kinetic energy?

Example Problem A pendulum is pulled to the side and released. Its subsequent motion appears as follows: 1. At which of the above times is the displacement zero? C, G 2. At which of the above times is the velocity zero? A, E, I 3. At which of the above times is the acceleration zero? C, G 4. At which of the above times is the kinetic energy a maximum? C, G 5. At which of the above times is the potential energy a maximum? A, E, I 6. At which of the above times is kinetic energy being transformed to potential energy? D, H 7. At which of the above times is potential energy being transformed to kinetic energy? B, F

Prediction Why is the slinky stretched more at the top than the bottom? A. The slinky is probably not in good shape and has been overstretched at the top. B. The slinky could be designed that way and if he holds it the other way around, it ll be denser at the top than the bottom. C. There s more mass pulling on the top loop so it has to stretch more to have a upward force kx equal to the weight mg.

Prediction Why is the slinky stretched more at the top than the bottom? A. The slinky is probably not in good shape and has been overstretched at the top. B. The slinky could be designed that way and if he holds it the other way around, it ll be denser at the top than the bottom. C. There s more mass pulling on the top loop so it has to stretch more to have an upward force kx equal to the weight mg.

Prediction How will the slinky fall? A. The entire thing will fall to the ground w/ an acceleration of g. B. The center of mass will fall w/ an acceleration of g as the slinky compresses making it look like the bottom doesn t fall as fast. C. The bottom will hover stationary in the air as the top falls until the top hits the bottom. D. Other watch video

Prediction How will the slinky fall? A. The entire thing will fall to the ground w/ an acceleration of g. B. The center of mass will fall w/ an acceleration of g as the slinky compresses making it look like the bottom doesn t fall as fast. C. The bottom will hover stationary in the air as the top falls until the top hits the bottom. D. Other

Why does this happen?