ImageQuick SIMM Setup Guide March 2001 www.lexmark.com
Edition: March 2001 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PAR- TICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. Comments about this publication may be addressed to Lexmark International, Inc., Department F95/ 032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call 0628-481500. In other countries, contact your point of purchase. References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user s responsibility. Lexmark, Lexmark with diamond design, MarkNet, MarkVision, and Optra are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. Drag'N'Print, ImageQuick, and OptraImage are trademarks of Lexmark International, Inc. Other trademarks are the property of their respective owners. Copyright 2001 Lexmark International, Inc. All rights reserved. UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.
Table of contents Before you begin.................................................. 1 Printer requirements........................................................ 1 Print server requirements.................................................... 1 ImageQuick software requirements............................................ 2 Step 1: Print the menu settings...................................... 3 Step 2: Install the ImageQuick SIMM................................ 5 Installing the SIMM in an Optra T printer....................................... 5 Installing the SIMM in an Optra W810 printer................................... 9 Installing the SIMM in an Optra C710 printer................................... 13 Installing the SIMM in a Lexmark C720 printer................................. 17 Step 3: Install the Lexmark ImageQuick software..................... 22 Step 4: Adjust print server settings................................. 23 Troubleshooting.................................................. 26 Lexmark ImageQuick SIMM Setup Guide iii
Before you begin Printer requirements The Lexmark ImageQuick SIMM is designed for use with Lexmark Optra T, Optra C710, Optra W810, and Lexmark C720 laser printers with a minimum of 8MB memory. Additional memory or a hard disk may be required for large or complex jobs. You need a number 2 Phillips screwdriver to install the SIMM. Print server requirements Your Optra T, Optra C710, Optra W810, or Lexmark C720 printer must either be networkready, or be equipped with one of the following Lexmark MarkNet N2000 Series print servers: MarkNet N2000t, N2001e, or N2002e Requires firmware version 3.12.19 or later. MarkNet N2501e or N2401e with OptraImage Requires firmware version 5.12.19 or later. Note: If multiple print servers are installed in your printer, SIMM functionality is only supported for one of them. To determine your print server firmware version, print a MarkNet network setup page. For more information about upgrading firmware, launch the Drivers, MarkVision and Utilities CD, click View Documentation, and look for the MarkNet link. The network print server must have TCP/IP configured and enabled. Refer to your printer setup manual or your print server manual for TCP/IP configuration. 1 Lexmark ImageQuick SIMM Setup Guide
ImageQuick software requirements ImageQuick software is supported on computers in the following environments: Windows 95/98, Windows NT 4.0, or Windows 2000 Sun Solaris 2.6, 7, or 8 Lexmark ImageQuick SIMM Setup Guide 2
Step 1: Print the menu settings Installing the ImageQuick SIMM may reset the printer s default menu settings. Print and save the list of current menu settings. For more information about using the printer operator panel and changing menu settings, refer to your printer documentation. To print your current printer settings: 1 Plug in the printer power cord and turn on the printer. 2 From the printer operator panel, press Menu> until UTILITIES MENU appears. 3 Press Select. 4 Press Menu> until Print Menus appears. UTILITIES MENU is on the first line, and Print Menus is on the second line. 5 Press Select. If an error message appears, refer to your printer documentation. 3 Lexmark ImageQuick SIMM Setup Guide
6 Locate your printer in the following table and turn to the appropriate page to begin installation of the ImageQuick SIMM. Type of printer See page Optra T 5 Optra W810 9 Optra C710 13 Lexmark C720 17 Lexmark ImageQuick SIMM Setup Guide 4
Step 2: Install the ImageQuick SIMM Installing the SIMM in an Optra T printer Accessing the system board You must access the printer system board to install the Lexmark ImageQuick SIMM. 1 Unplug the printer power cord and disconnect all cables from the back of the printer. 2 Press the release latches to open the upper and lower front doors. 5 Lexmark ImageQuick SIMM Setup Guide
3 Press on the side door latches and open the side door. 4 Loosen, but do not remove, the six screws, as shown. Screws Keyhole 5 Use the tabs to slide the shield up until the top three screws fit into the three keyholes on the shield. 6 Hold the shield by the tabs and lift it off. Tabs Lexmark ImageQuick SIMM Setup Guide 6
Installing the SIMM 1 Locate the optional firmware SIMM connector on the system board. Warning: Electronic components can be damaged by static electricity. Touch something metal or wear an antistatic wrist strap before handling the SIMM. 2 Hold the Lexmark ImageQuick SIMM with the connection points facing toward the system board with the notch as indicated below: For all models except the Optra T610 and T612 non-network models, hold the SIMM with the notch toward the bottom of the printer and insert the SIMM all the way into the connector at a 45 degree angle, as shown. For the Optra T610 and T612 non-network models, hold the SIMM with the notch toward the top of the printer and insert the SIMM at the opposite of the angle shown. 3 Press the SIMM toward the system board until it snaps into place. 7 Lexmark ImageQuick SIMM Setup Guide
Reattaching the shield 1 Holding the shield by the tabs, align the three keyholes on the shield with the top three screws on the printer. 2 Slide the shield down. 3 Tighten all six screws. Tabs 4 Close the side door, and then the upper and lower front doors. 5 Connect the printer cables and power cord, and turn the printer on. Verifying installation Print a menu settings page. (See page 3 for instructions.) If the SIMM is installed correctly, ImageQuick SIMM appears under the Printer Information section. After verifying the installation, you may want to reset your printer settings. Refer to the menu settings page you printed and saved before installing the SIMM. Lexmark ImageQuick SIMM Setup Guide 8
Installing the SIMM in an Optra W810 printer Accessing the system board If your Optra W810 has an optional finisher or mailbox attached, you must remove the option to access the printer system board. Refer to your printer documentation for the appropriate steps. 1 Unplug the printer power cord and disconnect all cables from the back of the printer. 2 Lift off the system board access cover and lay it aside. 3 Loosen the two screws on the shield. Do not remove the screws. 4 Remove the shield and lay it aside. 9 Lexmark ImageQuick SIMM Setup Guide
Installing the SIMM 1 Locate the optional firmware SIMM connector on the system board. Warning: Electronic components can be damaged by static electricity. Touch something metal or wear an antistatic wrist strap before handling the SIMM. 2 Hold the Lexmark ImageQuick SIMM with the connection points facing toward the system board and the notch toward the rear of the printer. Insert it all the way into the connector at a 45 degree angle (leaning toward the front of the printer). 3 Press the SIMM toward the system board until it snaps into place. Lexmark ImageQuick SIMM Setup Guide 10
Reinstalling the shield and access cover 1 Reinstall the shield. a Slide the tab on the shield under the lip of the opening, as shown. b Align the slots on the shield with the tabs. c Lower the shield into place. d Tighten the two screws. 11 Lexmark ImageQuick SIMM Setup Guide
2 Reinstall the system board access cover. a Insert the tabs on the system board access cover into the slots, as shown. b Lower the cover and gently push it down to snap it into place. Refer to your printer documentation to replace your finisher or mailbox. 3 Connect the printer cables and power cord, and turn the printer on. Verifying installation Print a menu settings page. (See page 3 for instructions.) If the SIMM is installed correctly, ImageQuick SIMM appears under the Printer Information section. After verifying the installation, you may want to reset your printer settings. Refer to the menu settings page you printed and saved before installing the SIMM. Lexmark ImageQuick SIMM Setup Guide 12
Installing the SIMM in an Optra C710 printer 1 Turn the printer off and disconnect the power cord and printer cables. 2 Loosen the four screws on the rear cover, as shown. The screws on the rear cover are captive and remain on the cover. 3 Remove the rear cover and lay it aside. 4 Loosen the six screws on the shield, as shown. The screws on the shield are captive and remain on the shield. 5 Lift and remove the shield, and then lay it aside. 13 Lexmark ImageQuick SIMM Setup Guide
Installing the SIMM 1 Locate the optional firmware SIMM connector on the system board. Warning: Electronic components can be damaged by static electricity. Touch something metal or wear an antistatic wrist strap before handling the SIMM. 2 Hold the Lexmark ImageQuick SIMM with the connection points facing toward the system board and the notch toward the bottom of the printer. Insert it all the way into the connector at a 45 degree angle (leaning toward the front of the printer). 3 Press the SIMM toward the system board until it snaps into place. Lexmark ImageQuick SIMM Setup Guide 14
Reinstalling the shield and rear cover 1 Insert the top of the shield, as shown. 2 Align the six screws in the shield with the holes on the printer. 3 Tighten the six screws. 15 Lexmark ImageQuick SIMM Setup Guide
4 Place the rear cover on the printer and align the screws. 5 Tighten the four screws. 6 Connect the printer cables and power cord, and turn the printer on. Verifying installation Print a menu settings page. (See page 3 for instructions.) If the SIMM is installed correctly, ImageQuick SIMM appears under the Printer Information section. After verifying the installation, you may want to reset your printer settings. Refer to the menu settings page you printed and saved before installing the SIMM. Lexmark ImageQuick SIMM Setup Guide 16
Installing the SIMM in a Lexmark C720 printer 1 Turn the printer off and disconnect the power cord and printer cables. 2 Remove the two screws on the system board cover as shown. Put the screws in a safe place so they are available when you reinstall the system board. 17 Lexmark ImageQuick SIMM Setup Guide
3 Pull the system board out of the printer. Installing the SIMM 1 Locate the optional firmware SIMM connector on the system board. Lexmark ImageQuick SIMM Setup Guide 18
Warning: Electronic components can be damaged by static electricity. Touch something metal or wear an antistatic wrist strap before handling the SIMM. 2 Hold the Lexmark ImageQuick SIMM with the connection points facing toward the system board and the notch toward the bottom of the printer. Insert it all the way into the connector at a 45 degree angle (leaning toward the front of the printer). 3 Press the SIMM toward the system board until it snaps into place. 19 Lexmark ImageQuick SIMM Setup Guide
Reinstalling the system board and cover 1 Turn the printer off. 2 Align the system board with the top and bottom slots inside the printer, as shown. 3 Insert the system board into the printer. Lexmark ImageQuick SIMM Setup Guide 20
4 Align the two screws in the system board cover with the holes on the printer frame. 5 Tighten the two screws. 6 Connect the printer cables and power cord, and turn the printer on. Verifying installation Print a menu settings page. (See page 3 for instructions.) If the SIMM is installed correctly, ImageQuick SIMM appears under the Printer Information section. After verifying the installation, you may want to reset your printer settings. Refer to the menu settings page you printed and saved before installing the SIMM. 21 Lexmark ImageQuick SIMM Setup Guide
Step 3: Install the Lexmark ImageQuick software The Lexmark ImageQuick software lets you manage printer bookmarks and use the Lexmark Drag'N'Print utility. To install the ImageQuick software, refer to the enclosed booklet with your ImageQuick CD and follow the instructions. Lexmark ImageQuick SIMM Setup Guide 22
Step 4: Adjust print server settings 1 Navigate your Web browser to the printer by typing the IP address or full name of the printer in the address line of your browser. 2 Press Enter. Note: See your network administrator if you are prompted for a password. 3 Click the Configuration tab in the left pane. 4 Under Print Server, in the right pane, click TCP/IP. 5 Click Advanced Settings. 6 Scroll down to Pull Printing in the right pane. 7 Adjust the print server fields. Print server fields Local Domains. The Local Domains field is a comma-, semicolon-, or space-delimited list of domains or IP subnets used to specify which addresses do not use the proxy server. To specify an IP subnet, use asterisks to represent the domain. For example, on a class B network, enter 192.168.*.* to designate all hosts within your domain as local. To specify local domains, simply enter the domain name. For example, to designate all machines in the Lexmark domain as local, enter 23 Lexmark ImageQuick SIMM Setup Guide
lexmark.com. You can also specify *.lexmark.com. If a Web server's IP address is specified (and if a proxy server is not set), the printer connects directly to that server. The printer does not need a Domain Name Server (DNS). If the proxy server is set, the host name or IP address is first checked against the Local Domains list. If it matches, the printer attempts to look up host names by way of DNS if set, and connects directly to IP addresses. If the host name or IP address does not match any of the entries in the Local Domains field, the printer connects to the host through the specified proxy server. DNS IP Address. The DNS translates the Web server name in the URL into its corresponding IP address. If no DNS is available and no proxy is configured, then you can only use IP addresses for pull printing. HTTP Proxy IP Address. This is the IP address of the system serving as the network proxy for HTTP requests. FTP Proxy IP Address. This is the IP address of the system serving as the network proxy for FTP requests. HTTP Proxy Port. This is the IP port number that the print server uses when attempting to communicate with the HTTP proxy. The default port number is 80 and is typically not changed. FTP Proxy Port. This is the IP port number that the print server uses when attempting to Lexmark ImageQuick SIMM Setup Guide 24
communicate with the FTP proxy. The default port number is 21 and is typically not changed. Timeout for HTTP/FTP requests. This field defines how long (in seconds) the server waits for a reply to an HTTP or FTP request. Retries. The Retries field specifies the maximum number of attempts that the printer makes to pull a file. The printer retries on timeouts, refused or unexpectedly broken connections, and proxy errors. Tip for print server configuration If the print server s Pull Printing settings have not been configured (that is, no DNS IP address has been set and the HTTP and FTP proxy addresses have not been set), the print server can still pull Web pages from Web servers that reside on the same IP subnet as the print server. The only requirement is that the pull print URL be in dotted-ip address format (for example, http://192.168.12.99/printpage.html). 25 Lexmark ImageQuick SIMM Setup Guide
Troubleshooting My Lexmark ImageQuick SIMM doesn t work. The Lexmark ImageQuick SIMM is only compatible with specific Lexmark printers. Verify that you installed the SIMM in the appropriate printer. (See page 1 for a list of compatible printers.) The SIMM may not be inserted into the connector correctly. Remove the SIMM and reinstall it. (See Install the ImageQuick SIMM beginning on page 5 for help.) I don t know my printer s IP address. Print the network setup page: 1 From the printer operator panel, press Menu> until UTILITIES MENU appears. 2 Press Select. 3 Press Menu> until PRINT NETx SETUP appears. UTILITIES MENU is on the first line, and PRINT NETx SETUP is on the second line. 4 Press Select. 5 Look for the IP address under the TCP/IP section on the page that prints. If your IP address has not been set, refer to your print server manual for the appropriate steps. Lexmark ImageQuick SIMM Setup Guide 26
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. 2001 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550 www.lexmark.com