HabaCHAIN Slat and Conveyor Chains

Products Media No. 4185 HabaCHAIN Slat and Conveyor Chains Product Guide Habasit Solutions in motion

This disclaimer is made by and on behalf of Habasit and its affiliated companies, directors, employees, agents and contractors (hereinafter collectively "HABASIT") with respect to the products referred to herein (the "Products"). SAFETY WARNINGS SHOULD BE READ CAREFULLY AND ANY RECOMMENDED SAFETY PRECAUTIONS FOLLOWED STRICTLY! Please refer to the Safety Warnings herein, in the Habasit catalogue as well as installation and operating manuals. All indications / information as to the application, use and performance of the Products are recommendations provided with due diligence and care, but no representations or warranties of any kind are made as to their completeness, accuracy or suitability for a particular purpose. The data provided herein are based on laboratory application with small-scale test equipment, running at standard conditions, and do not necessarily match product performance in industrial use. New knowledge and experience may lead to re-assessments and modifications within a short period of time and without prior notice. EXCEPT AS EXPLICITLY WARRANTED BY HABASIT, WHICH WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, THE PRODUCTS ARE PROVIDED "AS IS". HABASIT DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE, ALL OF WHICH ARE HEREBY EXCLUDED TO THE EXTENT ALLOWED BY APPLICABLE LAW. BECAUSE CONDITIONS OF USE IN INDUSTRIAL APPLICATION ARE OUTSIDE OF HABASIT'S CONTROL, HABASIT DOES NOT ASSUME ANY LIABILITY CONCERNING THE SUITABILITY AND PROCESS ABILITY OF THE PRODUCTS, INCLUDING INDICATIONS ON PROCESS RESULTS AND OUTPUT.! WARNING Habasit belts and chains are made of various plastics that WILL BURN if exposed to sparks, incendiaries, open flame or excessive heat. NEVER expose plastic belts and chains to a potential source of ignition. Flames resulting from burning plastics may emit TOXIC SMOKE and gasses as well as cause SERIOUS INJURIES and PROPERTY DAMAGE. See the Fire Hazard Data Sheet for additional information.

Contents 3 Introduction Product types 5 Getting started Chain selection criteria 6 Nomenclature 7 Material overview 12 Slat Top plastic chains 770T (radius) 1.0" 17 820 (straight) 1.5" 18 821 (straight) 1.5" 19 828 (straight) 1.5" 20 831 (straight) 1.5" 21 879B (radius) 1.5" 22 879T (radius) 1.5" 23 880B (radius) 1.5" 24 880LJ (radius) 1.5" 25 880J (radius) 1.5" 26 880T (radius) 1.5" 27 880M (radius) 1.5" 28 882B (radius) 1.5" 29 882T (radius) 1.5" 30 882TG (radius) 1.5" 31 890T (radius) 1.5" 32 1061T (radius) 1.0" 33 1061M (radius) 1.0" 34 Slat Top plastic accessories 35 Low Back Pressure chains 821 (straight) 1.5" 37 821 SB (straight) 1.5" 38 882T (radius) 1.5" 39 882T SB (radius) 1.5" 40 Slat Top steel chains 800 (straight) 1.5" 41 810 (straight) 1.5" 42 881B (radius) 1.5" 44 881T (radius) 1.5" 45 Slat Top steel accessories 46 Flexi chains 7100HA 47 Snap-on chains 843 (straight) 0.50" 48 843C (straight) 0.50" 49 863 (straight) 0.75" 50 863T (straight) 0.75" 51 963 (straight) 0.75" 52 963T (straight) 0.75" 53 1843T (radius) 0.50" 54 1873T (radius) 0.75" 55 1873T -T (straight) 0.75" 56 1873-D1 (radius) 0.75" 57 1873-L4 (radius) 0.75" 58 1874T (radius) 0.75" 59 3873T (radius) 0.75" 60 Snap-on accessories 61 Multiflex chains 1700 (radius) 1.97" 62 1701T (radius) 1.97" 63 1702 (radius) 1.97" 64 Multiflex accessories 65 Case chains 40P (straight) 0.50" 66 60P (straight) 0.75" 67 600 (radius) 2.50" 68 601 (radius) 2.50" 69 610T (radius) 2.50" 70 611T (radius) 2.50" 71 611TE (radius) 2.50" 72 1100 (straight) 1.00" 73 1110T (radius) 1.00" 74 1150 (straight) 1.50" 75 1151T (radius) 1.50" 76 1200 (straight) 2.00" 77 1201AB (straight) 2.00" 78 1210T (radius) 2.00" 79 1211TB (radius) 2.00" 80 1250 (straight) 2.50" 81 1251T (radius) 2.50" 82 1400 (radius) 3.25" 83 1410T (radius) 3.25" 84 3200 (straight) 2.00" 85 3210T (radius) 2.00" 86 NH78 (straight) 2.61" 87 Case chain accessories 88

Contents 4 Multi-Hub sprockets and idlers Product information 92 820 Sprocket rims 93 820 Idler rims 94 821 Sprocket rims 95 880 Sprocket rims 96 881 Sprocket rims 97 882 Sprocket rims 98 1060 Sprocket rims 99 Multi-Hub inserts 100 Solid sprockets and idlers 600 Sprockets 101 810 Sprockets 102 810 Idlers 103 820 Sprockets 104 821 Sprockets 105 880 Sprockets 106 881 Sprockets 107 882 Sprockets 108 1100 Sprockets 109 1150 Sprockets 110 1200 Sprockets 111 1250 Sprockets 112 1400 Sprockets 113 1700 Sprockets 114 3200 Sprockets 115 7100 Sprockets 116 7100 Idlers 117 NH78 Sprockets 118 Split sprockets 1061 Sprockets 119 Retainer rings Retainer rings 120 Appendix Chemical resistance Plastics 122 Chemical resistance Steel 127 Safety information 128 The Habasit solution 130

Product types 5 Slat Top plastic chains Available in straight running 820, 821, 828 and 831. Radius chain available in 879, 880, 882 and 1061. Tight turning radius available in 770 and 890. Low Back pressure chains Standard version 821 and 882 as well as patented sliding block system available. Slat Top Steel chains Available in four steel qualities and designed for the beverage industry, as well as for heavy duty, high temperature and static electricity applications. Flexi chains For standardized modular conveyor systems made of aluminum or steel profiles. Snap-on chains Multiflex chains Two-piece chain with steel roller base The 1700, 1701T and 1702 are heavy chain and plastic top plate. Base duty biplanar chains. Applications chains in two dimensions (ANSI 40 = include alpine systems (inline 0.5" pitch or ANSI 60 = 0.75" pitch) accumulation) and case conveyors. and made of carbon or stainless steel. Case chains Case chains are available in many different designs ranging from 0.5" pitch to 3.25" pitch. The popular 1200/3200 series chain was developed and patented. Multi-Hub sprockets and idlers Different split sprockets or idlers can be combined with different hub inserts. Solid sprockets and idlers Machined or molded solid sprockets and idlers. Made of plastics or steel. Split sprockets Machined split sprockets Retainer rings For lateral fixation of sprockets and idlers on round and square shafts.

Getting started Chain selection criteria 6 What do you need to know to select the right chain type? How can you get the necessary information? We outline several things below to think about when selecting a chain type, and indicate where you can find specific information. Chain path Conveyor chains can run either through curves and/ or straight. We refer to them as radius or straight. Radius chains are also known as sideflexing chains. Straight chains generally have a higher load capacity than radius chains. Chain accessories HabaCHAIN offers a variety of special accessories. You can find them listed in this Product Guide at the end of each product groups. Chain material HabaCHAIN offers a variety of different materials to meet specific application requirements. Some of these are only available on request. Pin material Stainless steel pins are available in magnetic and nonmagnetic alloys. Chain color For standard colors please refer to the Material Overview. Other colors are available on request. Sprockets and idlers Multi-Hub and Solid types are available. The Product Data Sheet (PDS) HabaCHAIN Slat Top 820 (Straight) Product type Photo: Straight product running plastic is chain shown 820 hinge the design most = identical sprocket for 820 and 831 series chains common For side transfer material with (in 770, 880 or 890 series radius running chains this case LF) 18 Drawing: indicates the main dimensions (characters/figures are displayed in the data chart below) Habasit code (descriptive) Chain data Chain weight: value is indicative R b = Backbending radius R s = Sideflexing radius R a = Top plate roughness Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0820K0250DPAA 63.5 2.50 0.74 0.50 1650 371 DP C0820K0250LFAA 63.5 2.50 0.74 0.50 1650 371 LF C0820K0250PTAA 63.5 2.50 0.74 0.50 1650 371 PT Additional documentation is available: HabaCHAIN website (www.habasit.com) HabaCHAIN Product overview (Media No. 4122) HabaCHAIN Engineering guide (Media No. 6017) or contact your local Habasit partner.

Nomenclature 7 Chain code Chain type Version: K = Standard pin (AISI 430), L = Plastic pin (PA), M = Magnetic, P = AISI 304 pin, S = Snap-on, B = Base chain, Q = AISI 316 pin, D = Bushing, = Single link, N = Plastic pin (NG) Chain width: (or pitch for base chains or connecting links) Material: (see material overview) Link design: A = Standard, T = Tab, B = Bevel, P = Multi-Hinge, J = Special bevel, H = Heavy duty, K = No backbending Style: A = Standard, G = GripTop, F = Flight, R = Low back pressure, S = Sliding block, W = Wave Top, C = Curve Top, P = Pusher, E = Modified tab Extensions C 0 0 0 0 K 0 0 0 0 L F A A X X X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Extensions Type: digits 16 and 17 WG Wide gap hinges L4 Four finger GripTop D1 Tubular GripTop R1 Bent right L1 Bent left, RL Bent both sides T 1873T-T TP Snap-on top plate Building pattern for chains with accessories: digits 16 and 17 01 Accessory on each module 02 Accessory on every second module per 10 ft 03 Accessory on every third module per 10 ft 04 Accessory on every fourth module per 10 ft Colors (on request): digit 18.. 1 White.. 2 Gray.. 3 Blue.. 4 Black.. 8 Dark gray.. 9 Natural.. A Green.. N Granite Examples C0882K0750PTTR Chain 882 Version Standard Width 7.50 inch Material PT Link design Tab Style Low back pressure C0810K0325CSAA-WG Chain 810 Version Standard Width 3.25 inch Material CS Link design Standard Style Standard Extension Wide gap hinges C1873S0375LFTG-D1 Chain 1873 Version Snap-on Width 3.75 inch Material LF Link design Tab Style GripTop Extension Tubular GripTop

Nomenclature 8 Multi-Hub sprocket and idler code (single items) Multi-Hub sprocket rims and idler rims Multi-Hub inserts Chain type Type: G = Sprocket, L = Idler Teeth: (equiv. no. for Idler) Material: GS = 8, ND = 7, L = 9 Extensions C 0 0 0 0 G 0 0 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 Shaft diameter Shaft type: R = Round Type: Z = Drive, L = Idler Set screw adapter Material: GS = 8, ND = 7, L = 8 Extensions H 0 0 0 R Z 0 0 0 1 2 3 4 5 6 7 8 9 10 Set screw adapter = Separator (if not required) L = For 1" round bores S = For all other imperial bores Examples C0820G257 Chain 820 or similar engagement Type Multi-Hub Sprocket rim Teeth 25 Material Special noise dampening material C0820L219 Chain 820 or similar engagement Type Multi-Hub Idler-Rim Teeth 21 Material L H030RZ-8 Multi-Hub Insert Shaft diameter 30 mm Shaft type Round Type Drive Material GS H100RL-9 Multi-Hub Insert Shaft diameter 1.00 inch Shaft type Round Type Idler Material L

Nomenclature 9 Solid sprocket and idler code, multi-hub assembly code Solid sprockets and idlers Chain type Type: M = Machined Sprocket, L = Idler, S = Molded sprocket, Z = Split sprocket, A = Multi-Hub sprocket assembly, E = Multi-Hub idler assembly Teeth: (equiv. no. for Idler) Material: (see material overview) Bore size: (see code below) Bore shape: R = Round with keyway, Q = Square, L = Round with clearance Hub type of Flexi 7100 chain type: (A, B, C, E, M, 2, 3, 4 see code below) Extensions C 0 0 0 0 S 0 0 P E 0 0 R A X X X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Bore size: digits 11 and 12 Round shape Square shape Code Diameter Code Diameter Code Diameter Code Width Code Width 00 Pilot bore 50 50 mm 32 1.25" 25 25 mm 02 1" 20 20 mm 60 60 mm 37 1 7/16" 40 40 mm 03 1.5" 25 25 mm 90 90 mm 03 1.5" 50 50 mm 04 2" 30 30 mm 01 0.75" 04 2" 60 60 mm 05 2.5" 35 35 mm 02 1" 05 2.5" 40 40 mm 31 1 3/16 07 3.5" Hub type or Flexi 7100 chain type: digit 14 2 for C7100K0248 chain 3 for C7100K0325 chain 4 for C7100K0405 chain Extensions Colors (on request): digit 18.. 1 White.. 4 Black Examples C0810L19PE Chain 810 or similar engagement Type Idler Teeth 19 Material PE C3200M08PE03QC Chain 3200 or similar engagement Type Machined Sprocket Teeth 08 Material PE Bore size 1.5 inch Bore shape Square Hub type C

Nomenclature 10 Accessories code Chain type Version: K = Standard pin (AISI 430), L = Plastic pin (PA), M = Magnetic, P = AISI 304 pin, S = Snap-on, B = Base chain, Q = AISI 316 pin, D = Bushing, = Single link, N = Plastic pin (NG) Chain width: (special code only for accessories see below) Accessories: (see code below) Material: (see material overview) Link design: A = Standard, T = Tab B = Bevel P = Multi- Hinge, J = Special bevel, H = Heavy duty, K = No backbending Style: A = Standard, G = GripTop, F = Flight, R = Low back pressure, S = Sliding block, W = Wave Top, C = Curve Top, P = Pusher, E = Modified tab Extensions C 0 0 0 0 K 0 0 0 E P L F A A X X X 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Chain width: digits 7 to 9 Code Code Code Code 100 1.00" 210 2.10" 330 3.30" Q12 12.00" 125 1.25" 219 2.19" 375 3.75" Q15 15.00" 138 1.38" 224 2.24" 400 4.00" Q16 16.00" 144 1.44" 225 2.25" 405 4.05" 150 1.50" 248 2.48" 450 4.50" 165 1.65" 250 2.50" 600 6.00" 169 1.69" 291 2.91" 750 7.50" 200 2.00" 325 3.25" Q10 10.00" Accessories: digits 10 and 11 EP Extended pin HR Half round pusher A1 Plastic tab one hole (one side) A2 Plastic tab one hole (two sides) K1 Stainless steel attachment K2 Plastic tab two holes (two sides) CT Cone Line Module X_ Custom insert type (see Slat Top Plastic and Snap-on Accessories) TP Snap-on top plate For custom accessories contact your local Habasit partner. Extensions Building pattern for chains with accessories: digits 17 and 18 01 Accessory on each module 02 Accessory on every second module per 10 ft 03 Accessory on every third module per 10 ft 04 Accessory on every fourth module per 10 ft Colors (on request): digit 19 (for Extended pin version digit 19 indicates the pin diameter instead of the color).. 1 White.. 2 Gray.. 3 Blue.. 4 Black.. 8 Dark gray.. 9 Natural.. A Green

Nomenclature 11 Examples C0820K325XAPTAA-05 Chain 820 Version Standard Width 3.25 inch Accessory Custom insert type A Material PT Link design Standard Style Standard Extension Accessory on every fifth module per 10 ft C1873SQ12XBLFTA-11 Chain 1873 Version Snap-on Width 12.00 inch Accessory Custom insert type B Material LF Link design Tab Style Standard Extension Accessory on every 11th module per 10 ft C1200K224K2DPAA-031 Chain 1200 Version Standard Width 2.24 inch Accessory Plastic tab two holes (two sides) Material DP Link design Standard Style Standard Extension Accessory on every third module per 10 ft and color white CNH78K291EPLFAA-157 Chain NH78 Version Standard Width 2.91 inch Accessory Extended pin Material LF Link design Standard Style Standard Extension Accessory on every 15th module per 10 ft and pin diameter 7/16 inch C7100T325 Chain 7100 Version Pin tool Width 3.25 inch

Material overview 12 Plastic chains HabaCHAIN products are made of high quality plastics from the best raw material producers. Habasit s program of studying material applications ensures the most suitable plastic type material for the particular conditions, as listed below: Plastic chains Standard chain materials Material DP LF PT TS NG Standard POM (Acetal) 1) with good strength and good coefficient of friction. Entry level material for standard or low speed applications. Low-friction POM (Acetal) 1) with high strength and good abrasion resistance. Suitable for high speed applications. Food contact approved. Low-friction POM (Acetal) 1) The material shows a low coefficient of friction, high strength and good abrasion resistance. Suitable for high speed applications with reduced lubrication Extra low-friction POM (Acetal) 1) with special self-lubricating agents. This material has the lowest friction values and highest PxV (load and speed) limit. Extra low friction PBT material with good strength and very good abrasion resistance. Suitable for high speed, dry running applications. Should be used in combination with a high performance corner track. Density [g/cm 3 ] 1.42 1.42 1.43 1.43 1.32 Temperature range Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +60 C (-40 F to +140 F) Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +60 C (-40 F to +140 F) Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +60 C (-40 F to +140 F) Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +60 C (-40 F to +140 F) Dry conditions: -40 C to +120 C (-40 F to +248 F) Wet conditions: -40 C to +50 C (-40 F to +122 F) Standard color Gray Light brown for Flexi Chains: White Graybrown for Flexi Chains: White Silver Gray Plastic chains Special chain materials Material Density [g/cm 3 ] Temperature range For special materials, strength reduction and dimensional variation to be expected. Please consult with Habasit Engineering. PK EC Extra wear-resistant aramidic fiber-filled POM (Acetal) 1). The special formulation ensures good wear resistance and a low coefficient of friction, especially for abrasive, wet or dry running applications. POM (Acetal) 1) with an electrical surface resistivity below 50.000 Ohm/sq (DIN/EN 1637). Material has high strength and a good coefficient of friction. Especially for applications where chain charge-up must be avoided. To be used with a conductive wear strip. 1.41 1.42 Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +66 C (-40 F to +151 F) Dry conditions: -40 C to +93 C (-40 F to +200 F) Standard color Dark gray Black 1) POM (Acetal) generally shows good resistance to oil and alkalines and has a cut-resistant surface.

Material overview 13 Plastic chains Special chain materials Material DE NY WR HT NP PP CR POM (Acetal) 1) with a special additive to ensure the material is detectable for metal and X-ray systems. PA with high strength and abrasion resistance. Material has very good long-term heat resistance. Suitable for high load, dry conditions and elevated temperatures. Flammability rating UL94 V2 Extra wear-resistant PA for dry and abrasive applications (glass). Higher wear resistance than NY with a low coefficient of friction. When using this material, it is necessary to use a synthetic lubricating agent (no water). Reinforced PA with very high strength and toughness. Suitable for high loads, dry conditions, at elevated temperatures. Flammability rating UL94 HB. PBT with good strength and low coefficient of friction. Developed for conveying applications in the tobacco industry. Glass fiber reinforced PP designed for demanding applications where a high level of chemical resistance is required. Extremely chemical resistant fluorinated thermoplastic material. Good strength, low friction and good abrasion resistance. Especially for applications with high demands for chemical or hot water resistance. Density [g/cm 3 ] 1.67 1.14 1.35 1.37 1.30 1.13 1.78 Temperature range Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +66 C (-40 F to +151 F) Dry conditions: -46 C to +118 C short-term +135 C (-50 F to +245 F short-term +275 F) Wet conditions: not recommended Dry conditions: -18 C to +82 C (0 F to +180 F) Wet conditions: not recommended Dry conditions: -40 C to +145 C short-term +175 C (-40 F to +293 F short-term +347 F) Wet conditions: not recommended Dry conditions: -40 C to +120 C (-40 F to +248 F Wet conditions: -40 C to +50 C (-40 F to +122 F) +5 C to +105 C (+40 F to + 220 F) Dry conditions: +5 C to +115 C (+40 F to +239 F) Wet conditions: +5 C to +115 C (+40 F to +239 F) Standard color Blue Dark gray Black Black Natural white Natural white White

Material overview 14 Steel chains Material Density [g/cm 3 ] CS Carbon steel - 43 HRC 7.85 SS SH SA Inox for standard applications - Ferritic stainless steel, magnetic qualities, and good chemical resistance. Suitable for most applications and environments. Hard Inox for high strength applications - Martensitic stainless steel, magnetic qualities, better mechanical resistance and less chemical resistance, Ra < 0.3 18/8 SS with high chemical resistance - Austenitic stainless steel, non-magnetic, with better chemical resistance and wear resistance, but less mechanical strength. Used in tough environments or for esthetic reasons. 7.90 7.70 7.90 Temperature range Wet conditions: not recommended Dry conditions: -40 C to +180 C (-40 F to +355 F) Dry conditions: -40 C to +260 C (-40 F to +500 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Dry conditions: -40 C to +260 C (-40 F to + 500 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Dry conditions: -40 C to +400 C (-40 F to +752 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Standard color Black Gray Gray Gray Pins Material SS SA IN PA Standard applications - Ferritic stainless steel, magnetic qualities, and good chemical resistance. Suitable for most applications and environments. Standard pin for plastic and steel chains. AISI 430 (Chain code K) High chemical resistance - Austenitic stainless steel, non-magnetic, with better chemical resistance and wear resistance, but less mechanical strength. Used in tough environments or for esthetic reasons. Steel chains only. AISI 304 (Chain code P) High chemical resistance - Austenitic stainless steel, nonmagnetic with increased resistance to chloride corrosion. AISI 316 (Chain code Q) Wear and fatigue resistant highly reinforced Polyamide. Easy to recycle option for plastic chains. Chain code N Density [g/cm 3 ] 7.90 7.90 7.90 1.55 Temperature range Dry conditions: -40 C to +260 C (-40 F to +500 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Dry conditions: -40 C to +400 C (-40 F to +752 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Dry conditions: -40 C to +400 C (-40 F to +752 F) Wet conditions: -40 C to +120 C (-40 F to +248 F) Dry conditions: -40 C to +145 C short-term +175 C (-40 F to +293 F short-term +347 F) Wet conditions: not recommended Standard color Gray Gray Gray Natural beige

Material overview 15 Pins Material NG Extra low friction PBT material with good strength and very good abrasion resistance. Easy to recycle for selected plastic chains. Density [g/cm 3 ] 1.13 Temperature range Dry conditions: -40 C to +120 C (-40 F to +248 F Wet conditions: -40 C to +50 C (-40 F to +122 F) Standard color Natural white Sprockets Material GS ND PE NY L CI Reinforced polyamide with high strength and wear resistance for long life Multi-Hub sprockets. Tough, wear resistant and noise dampening material for Multi-Hub sprockets. Tough, wear resistant and noise dampening UHMWPE. Not suitable for abrasive applications. For machined sprockets. High heat resistant, good abrasion resistant polyamide sprocket material. For machined sprockets. Extra low friction POM (Acetal) with self-lubricating agent for Multi-Hub idler and moulded sprockets. Cast iron for solid sprockets. Suitable in non-corrosive, abrasive environments, such as glass conveying. Density [g/cm 3 ] 1.37 1.24 0.94 1.14 1.41 7.85 Temperature range Dry conditions: -46 C to +118 C (-50 F to +245 F Wet conditions: -40 C to +50 C (-40 F to +122 F) -20 C to +50 C (-4 F to + 120 F) -70 C to +65 C (-94 F to +150 F) Dry conditions: -46 C to +118 C short-term +135 C (-50 F to +245 F short-term +275 F) Wet conditions: not recommended Dry conditions: -40 C to +93 C (-40 F to +200 F) Wet conditions: -40 C to +60 C (-40 F to +140 F) Dry conditions: -40 C to +180 C (-40 F to +355 F) Wet conditions: not recommended Standard color Black Dark gray Natural white Natural white Black Black Accessories Material Density [g/cm 3 ] G For GripTop inserts on Slat Top Plastic Chains 1.16 PL For GripTop inserts on Slat Top Plastic and Snap-on Chains 1.14 HY For GripTop inserts on Slat Top Plastic and Snap-on Chains 1.20 PP Polypropylene glass fiber reinforced, for retainer rings 1.13 Temperature range -40 C to +60 C (-40 F to +140 F) -40 C to +80 C (-40 F to +176 F) -40 C to +110 C (-40 F to +230 F) +5 C to +105 C (+40 F to +220 F) Standard color Black or White Black or White Black or white Blue

Material overview 16 Characteristics Plastics DP LF PT TS NG PK EC DE NY WR HT PP CR PA GS ND PE L Impact resistance Wear resistance Chemical resistance Chemical resistance (high requirements) Low friction Suitability in wet environments Electrically conductive Direct food contact Magnetic Noise dampening Plasics Steel Characteristics G PL HY CS CI SS SH SA IN Impact resistance Wear resistance Chemical resistance Chemical resistance (high requirements) Low friction Suitability in wet environments Electrically conductive Direct food contact Magnetic Noise dampening

Slat Top 770T (radius) 17 Radius running plastic tab chain Small pitch for smooth product transfer with short dead plates Capable to run on corner discs 1061 hinge design = identical sprocket for 770 and 1061 series chains For conveyor layouts requiring tight turns For side transfer with 820 and 828 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0770K0325LFTA 82.6 3.25 1.12 0.75 1500 337 46.0 1.81 44.5 1.75 260 10.2 LF C0770K0325PTTA 82.6 3.25 1.12 0.75 1500 337 46.0 1.81 44.5 1.75 260 10.2 PT C0770K0325TSTA 82.6 3.25 1.12 0.75 1500 337 46.0 1.81 44.5 1.75 260 10.2 TS Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 1060 sprocket rims (see page 99) Multi-Hub inserts (see page 100) Split sprockets Series 1061 (see page 119)

Slat Top 820 (straight) 18 Straight running plastic chain 820 hinge design = identical sprocket for 820 and 831 series chains For side transfer with 770, 880 or 890 series radius running chains Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0820K0250DPAA 63.5 2.50 0.74 0.50 1650 371 DP C0820K0250LFAA 63.5 2.50 0.74 0.50 1650 371 LF C0820K0250PTAA 63.5 2.50 0.74 0.50 1650 371 PT C0820K0325DPAA 82.6 3.25 0.85 0.57 1650 371 DP C0820K0325LFAA 82.6 3.25 0.85 0.57 1650 371 LF C0820K0325PTAA 82.6 3.25 0.85 0.57 1650 371 PT C0820K0400DPAA 101.6 4.00 0.95 0.64 1650 371 DP C0820K0400LFAA 101.6 4.00 0.95 0.64 1650 371 LF C0820K0400PTAA 101.6 4.00 0.95 0.64 1650 371 PT C0820K0450DPAA 114.3 4.50 1.03 0.69 1650 371 DP C0820K0450LFAA 114.3 4.50 1.03 0.69 1650 371 LF C0820K0450PTAA 114.3 4.50 1.03 0.69 1650 371 PT C0820K0600DPAA 152.4 6.00 1.25 0.84 1650 371 DP C0820K0600LFAA 152.4 6.00 1.25 0.84 1650 371 LF C0820K0600PTAA 152.4 6.00 1.25 0.84 1650 371 PT C0820K0750DPAA 190.5 7.50 1.47 0.99 1650 371 DP C0820K0750LFAA 190.5 7.50 1.47 0.99 1650 371 LF C0820K0750PTAA 190.5 7.50 1.47 0.99 1650 371 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 820 sprocket rims (see page 93) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 820 (see page 104) Solid idlers Series 810 (see page 103) Options Plastic pin

Slat Top 821 (straight) 19 Straight running plastic chain Thick top plate = longer wear life Heavy duty double hinge design = identical sprocket for 800 and 821 series chain For side transfer with 879 and 882 series radius running chains Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0821K0750DPAA 190.5 7.50 2.60 1.75 2850 641 DP C0821K0750LFAA 190.5 7.50 2.60 1.75 2850 641 LF C0821K0750PTAA 190.5 7.50 2.60 1.75 2850 641 PT C0821K1000DPAA 254.0 10.00 3.10 2.08 2850 641 DP C0821K1000LFAA 254.0 10.00 3.10 2.08 2850 641 LF C0821K1000PTAA 254.0 10.00 3.10 2.08 2850 641 PT C0821K1200DPAA 304.8 12.00 3.40 2.28 2850 641 DP C0821K1200LFAA 304.8 12.00 3.40 2.28 2850 641 LF C0821K1200PTAA 304.8 12.00 3.40 2.28 2850 641 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 821 sprocket rims (2 set-up side-by-side) (see page 95). Multi-Hub inserts (see page 100) Solid sprockets Series 821 (see page 105)

Slat Top 828 (straight) 20 Straight running plastic chain 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 770, 880 or 890 series radius running chains Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0828K0330LFAA 83.8 3.30 0.89 0.60 1700 382 LF Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idler 810 (see page 103)

Slat Top 831 (straight) 21 Straight running plastic chain Thick top plate = longer wear life 820 hinge design = identical sprocket for 820 and 831 series chains For side transfer with 879 and 882 series radius running chains Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0831K0325DPAA 82.6 3.25 1.00 0.67 1650 371 DP C0831K0325LFAA 82.6 3.25 1.00 0.67 1650 371 LF C0831K0325PTAA 82.6 3.25 1.00 0.67 1650 371 PT C0831K0450DPAA 114.3 4.50 1.30 0.87 1650 371 DP C0831K0450LFAA 114.3 4.50 1.30 0.87 1650 371 LF C0831K0450PTAA 114.3 4.50 1.30 0.87 1650 371 PT C0831K0750DPAA 190.5 7.50 1.82 1.22 1650 371 DP C0831K0750LFAA 190.5 7.50 1.82 1.22 1650 371 LF C0831K0750PTAA 190.5 7.50 1.82 1.22 1650 371 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 820 sprocket rims (see page 93) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 820 (see page 104) Solid idlers Series 810 (see page 103) Options Plastic pin

Slat Top 879B (radius) 22 Radius running plastic bevel chain Thick top plate = longer wear life 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 821 and 831 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0879K0325DPBA 82.6 3.25 1.00 0.67 1900 428 44.5 1.75 41.3 1.62 457 18.0 DP C0879K0325LFBA 82.6 3.25 1.00 0.67 1900 428 44.5 1.75 41.3 1.62 457 18.0 LF C0879K0325PTBA 82.6 3.25 1.00 0.67 1900 428 44.5 1.75 41.3 1.62 457 18.0 PT C0879K0450DPBA 114.3 4.50 1.25 0.84 1900 428 44.5 1.75 41.3 1.62 500 19.7 DP C0879K0450LFBA 114.3 4.50 1.25 0.84 1900 428 44.5 1.75 41.3 1.62 500 19.7 LF C0879K0450PTBA 114.3 4.50 1.25 0.84 1900 428 44.5 1.75 41.3 1.62 500 19.7 PT C0879K0750DPBA 190.5 7.50 1.92 1.29 1900 428 44.5 1.75 41.3 1.62 610 24.0 DP C0879K0750LFBA 190.5 7.50 1.92 1.29 1900 428 44.5 1.75 41.3 1.62 610 24.0 LF C0879K0750PTBA 190.5 7.50 1.92 1.29 1900 428 44.5 1.75 41.3 1.62 610 24.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idlers Series 810 (see page 103) Options Plastic pin

Slat Top 879T (radius) 23 Radius running plastic tab chain Thick top plate = longer wear life 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 821 and 831 series straight running chains Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0879K0325DPTA 82.6 3.25 1.06 0.71 1900 428 457 18.0 DP C0879K0325LFTA 82.6 3.25 1.06 0.71 1900 428 457 18.0 LF C0879K0325PTTA 82.6 3.25 1.06 0.71 1900 428 457 18.0 PT C0879K0450DPTA 114.3 4.50 1.30 0.87 1900 428 500 19.7 DP C0879K0450LFTA 114.3 4.50 1.30 0.87 1900 428 500 19.7 LF C0879K0450PTTA 114.3 4.50 1.30 0.87 1900 428 500 19.7 PT C0879K0750DPTA 190.5 7.50 1.98 1.33 1900 428 610 24.0 DP C0879K0750LFTA 190.5 7.50 1.98 1.33 1900 428 610 24.0 LF C0879K0750PTTA 190.5 7.50 1.98 1.33 1900 428 610 24.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Options Plastic pin

Slat Top 880B (radius) 24 Radius running plastic bevel chain 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 820 and 828 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0880K0325DPBA 82.6 3.25 0.89 0.60 1900 428 44.5 1.75 41.3 1.62 457 18.0 DP C0880K0325LFBA 82.6 3.25 0.89 0.60 1900 428 44.5 1.75 41.3 1.62 457 18.0 LF C0880K0325PTBA 82.6 3.25 0.89 0.60 1900 428 44.5 1.75 41.3 1.62 457 18.0 PT C0880K0450DPBA 114.3 4.50 1.04 0.70 1900 428 44.5 1.75 41.3 1.62 500 19.7 DP C0880K0450LFBA 114.3 4.50 1.04 0.70 1900 428 44.5 1.75 41.3 1.62 500 19.7 LF C0880K0450PTBA 114.3 4.50 1.04 0.70 1900 428 44.5 1.75 41.3 1.62 500 19.7 PT C0880K0750DPBA 190.5 7.50 1.40 0.94 1900 428 44.5 1.75 41.3 1.62 610 24.0 DP C0880K0750LFBA 190.5 7.50 1.40 0.94 1900 428 44.5 1.75 41.3 1.62 610 24.0 LF C0880K0750PTBA 190.5 7.50 1.40 0.94 1900 428 44.5 1.75 41.3 1.62 610 24.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idlers Series 810 (see page 103) Options Plastic pin

Slat Top 880LJ (radius) 25 Radius running plastic bevel chain Easy disposal (all plastic design) High nominal tensile strength (3/4 of comparable steel pin chain) but 20% less weight Double hinge design with strong D-shape plastic pin 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 820 and 828 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0880L0325LFJA-00A 82.6 3.25 0.70 0.47 1050 236 43 1.69 40.5 1.59 600 23.6 LF Pin material: plastic (NG), white Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idler 810 (see page 103)

Slat Top 880J (radius) 26 Radius running plastic bevel chain Special bevel design without shark fin Single hinge design with D-shape steel pin 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 820 and 828 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0880K0325LFJA 82.6 3.25 0.89 0.60 1900 428 44.5 1.75 41.3 1.62 457 18.00 LF C0880K0450LFJA 114.3 4.50 1.04 0.70 1900 428 44.5 1.75 41.3 1.62 500 19.70 LF Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idler 810 (see page 103)

Slat Top 880T (radius) 27 Radius running plastic tab chain 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 820 and 828 series straight running chains Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0880K0325DPTA 82.6 3.25 1.00 0.67 1900 428 457 18.0 DP C0880K0325LFTA 82.6 3.25 1.00 0.67 1900 428 457 18.0 LF C0880K0325PTTA 82.6 3.25 1.00 0.67 1900 428 457 18.0 PT C0880K0450DPTA 114.3 4.50 1.16 0.74 1900 428 500 19.7 DP C0880K0450LFTA 114.3 4.50 1.16 0.74 1900 428 500 19.7 LF C0880K0450PTTA 114.3 4.50 1.16 0.74 1900 428 500 19.7 PT C0880K0750DPTA 190.5 7.50 1.35 0.99 1900 428 610 24.0 DP C0880K0750LFTA 190.5 7.50 1.35 0.99 1900 428 610 24.0 LF C0880K0750PTTA 190.5 7.50 1.35 0.99 1900 428 610 24.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Options Plastic pin

Slat Top 880M (radius) 28 Radius running plastic magnetic chain Held down in the curve by a magnetic corner track Easy removal from the corner track for cleaning or maintenance 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For side transfer with 820 and 828 series straight running chains Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0880M0325DPAA 82.6 3.25 0.90 0.62 1900 428 457 18.0 DP C0880M0325LFAA 82.6 3.25 0.90 0.62 1900 428 457 18.0 LF C0880M0325PTAA 82.6 3.25 0.90 0.62 1900 428 457 18.0 PT C0880M0330DPAA 83.8 3.30 0.91 0.61 1900 428 457 18.0 DP C0880M0330LFAA 83.8 3.30 0.91 0.61 1900 428 457 18.0 LF C0880M0330PTAA 83.8 3.30 0.91 0.61 1900 428 457 18.0 PT C0880M0450DPAA 114.3 4.50 1.07 0.72 1900 428 500 19.6 DP C0880M0450LFAA 114.3 4.50 1.07 0.72 1900 428 500 19.6 LF C0880M0450PTAA 114.3 4.50 1.07 0.72 1900 428 500 19.6 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Solid idler 810 (see page 103) Magnetic corner tracks see HabiPLAST Product Guide Code No. 4097

Slat Top 882B (radius) 29 Radius running plastic bevel chain Thick top plate = longer wear life Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0882K0450DPBA 114.3 4.50 1.79 1.20 2850 641 62 2.44 58 2.28 610 24.0 DP C0882K0450LFBA 114.3 4.50 1.79 1.20 2850 641 62 2.44 58 2.28 610 24.0 LF C0882K0450PTBA 114.3 4.50 1.79 1.20 2850 641 62 2.44 58 2.28 610 24.0 PT C0882K0750DPBA 190.5 7.50 2.20 1.48 2850 641 62 2.44 58 2.28 610 24.0 DP C0882K0750LFBA 190.5 7.50 2.20 1.48 2850 641 62 2.44 58 2.28 610 24.0 LF C0882K0750PTBA 190.5 7.50 2.20 1.48 2850 641 62 2.44 58 2.28 610 24.0 PT C0882K1000DPBA 254.0 10.00 2.52 1.69 2850 641 62 2.44 58 2.28 610 24.0 DP C0882K1000LFBA 254.0 10.00 2.52 1.69 2850 641 62 2.44 58 2.28 610 24.0 LF C0882K1000PTBA 254.0 10.00 2.52 1.69 2850 641 62 2.44 58 2.28 610 24.0 PT C0882K1200DPBA 304.8 12.00 2.75 1.85 2850 641 62 2.44 58 2.28 610 24.0 DP C0882K1200LFBA 304.8 12.00 2.75 1.85 2850 641 62 2.44 58 2.28 610 24.0 LF C0882K1200PTBA 304.8 12.00 2.75 1.85 2850 641 62 2.44 58 2.28 610 24.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 882 sprocket rims (see page 98) Multi-Hub inserts (see page 100) Solid sprockets Series 882 (see page 108)

Slat Top 882T (radius) 30 Radius running plastic tab chain Thick top plate = longer wear life For side transfer with 821 and 831 series straight running chains Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0882K0450DPTA 114.3 4.50 1.92 1.29 2850 641 610 24.0 DP C0882K0450LFTA 114.3 4.50 1.92 1.29 2850 641 610 24.0 LF C0882K0450PTTA 114.3 4.50 1.92 1.29 2850 641 610 24.0 PT C0882K0750DPTA 190.5 7.50 2.34 1.57 2850 641 610 24.0 DP C0882K0750LFTA 190.5 7.50 2.34 1.57 2850 641 610 24.0 LF C0882K0750PTTA 190.5 7.50 2.34 1.57 2850 641 610 24.0 PT C0882K1000DPTA 254.0 10.00 2.66 1.79 2850 641 610 24.0 DP C0882K1000LFTA 254.0 10.00 2.66 1.79 2850 641 610 24.0 LF C0882K1000PTTA 254.0 10.00 2.66 1.79 2850 641 610 24.0 PT C0882K1200DPTA 304.8 12.00 2.89 1.94 2850 641 610 24.0 DP C0882K1200LFTA 304.8 12.00 2.89 1.94 2850 641 610 24.0 LF C0882K1200PTTA 304.8 12.00 2.89 1.94 2850 641 610 24.0 PT C0882K1500DPTA 381.0 15.00 3.07 2.06 2850 641 686 27.0 DP C0882K1500LFTA 381.0 15.00 3.07 2.06 2850 641 686 27.0 LF C0882K1500PTTA 381.0 15.00 3.07 2.06 2850 641 686 27.0 PT C0882K1600DPTA 406.4 16.00 3.18 2.14 2850 641 686 27.0 DP C0882K1600LFTA 406.4 16.00 3.18 2.14 2850 641 686 27.0 LF C0882K1600PTTA 406.4 16.00 3.18 2.14 2850 641 686 27.0 PT Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 882 sprocket rims (see page 98) Multi-Hub inserts (see page 100) Solid sprockets Series 882 (see page 108)

Slat Top 882TG (radius) 31 Radius running plastic tab chain High friction GripTop inserts Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0882K0450LFTG 114.3 4.50 2.00 1.34 2850 641 610 24.0 LF C0882K0750LFTG 190.5 7.50 2.40 1.61 2850 641 610 24.0 LF Pin material: special stainless steel Standard packaging: 3.048 m = 10 ft with building pattern -01, for special building pattern see Product Guide, page Nomenclature Weights are only indicative Other materials on request Photo shows building pattern -01 GripTop width G: C0882K0450LFTG: 95mm C0882K0750LFTG: 132mm Related products Multi-Hub 882 sprocket rims (see page 98) Multi-Hub inserts (see page 100) Solid sprockets Series 882 (see page 108)

Slat Top 890T (radius) 32 Radius running plastic tab chain Capable to run on corner discs 880 hinge design = identical sprocket for 828, 879, 880, 890 series chains For conveyor layouts requiring tight turns For side transfer with 820 and 828 series straight running chains Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C0890K0325LFTA 82.6 3.25 0.98 0.66 1900 428 46.0 1.81 44.5 1.75 200 7.9 LF C0890K0450LFTA 114.3 4.50 1.10 0.74 1900 428 46.0 1.81 44.5 1.75 200 7.9 LF Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 880 sprocket rims (see page 96) Multi-Hub inserts (see page 100) Solid sprockets Series 880 (see page 106) Options Plastic pin

Slat Top 1061T (radius) 33 Radius running plastic tab chain Small pitch for smooth product transfer with short dead plates 1061 hinge design = identical sprocket for 770 and 1061 series chains For side transfer with HabasitLINK M2420 and M2470 Flat Top 1" modular belts Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C1061K0330DPTA 83.8 3.30 1.55 1.04 1650 371 500 19.7 DP C1061K0330LFTA 83.8 3.30 1.55 1.04 1650 371 500 19.7 LF C1061K0330PTTA 83.8 3.30 1.55 1.04 1650 371 500 19.7 PT C1061K0330TSTA 83.8 3.30 1.55 1.04 1650 371 500 19.7 TS Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 1060 sprocket rims (see page 99) Multi-Hub inserts (see page 100) Split sprockets Series 1061 (see page 119)

Slat Top 1061M (radius) 34 Radius running plastic magnetic chain Held down in the curve by a magnetic corner track Easy removal from the corner track for cleaning or maintenance Small pitch for smooth product transfer with short dead plates 1061 hinge design = identical sprocket for 770 and 1061 series chains For side transfer with HabasitLINK M2420 and M2470 Flat Top 1" modular belts Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C1061M0330DPAA 83.8 3.30 1.67 1.12 1650 371 500 19.7 DP C1061M0330LFAA 83.8 3.30 1.67 1.12 1650 371 500 19.7 LF C1061M0330PTAA 83.8 3.30 1.67 1.12 1650 371 500 19.7 PT C1061M0330TSAA 83.8 3.30 1.67 1.12 1650 371 500 19.7 TS Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Multi-Hub 1060 sprocket rims (see page 99) Multi-Hub inserts (see page 100) Split sprockets Series 1061 (see page 119) Magnetic corner tracks see HabiPLAST Product Guide Code No. 4097

Slat Top plastic accessories 35 Inserts Inserts can be fitted into most Slat Top plastic chain types to increase the friction between product and chain. This is beneficial for incline or decline applications. 1. Serial inserts (e.g. 882TG) Standard insert material is G 85 Shore A hardness Heavy duty insert 2. Custom inserts Standard insert material PL (other materials like HY available) 85 Shore A hardness (other hardness grades available in other materials) Available as individual links or assembled into chain lengths (standard packaging: 3.048 m = 10 ft) For order code of special building pattern see page Nomenclature Custom insert dimensions are shown in the table below Chain type Chain width Insert type Insert width L mm inch 325 60 2.36 400 (only 820) 90 3.54 820 / 831 450 XA 105 4.13 600 (only 820) 750 130 5.12 821 750 130 5.12 XA 1000 200 7.87 1200 XB 295 11.61 879 / 880 882B / 882T 882T 325 60 2.36 450 XA 90 3.54 750 130 5.12 450 90 3.54 750 XA 130 5.12 1000 200 7.87 1200 XB 295 11.61 1500 1600 XB 295 11.61 Type XA Type XB This is only a brief overview of our inserts. Many different insert designs are available.

Slat Top plastic accessories 36 Drilled holes For special applications (e.g. vacuum) when holes in Slat Top chains are needed, we offer HabaCHAIN Slat Top plastic chains with custom-made drilled holes. The holes are drilled on a dedicated CNC machine according to the pattern specified by the customer. All types of hole shapes (not only round) can be machined. For further information and availability please contact your local Habasit partner.

LBP 821 (straight) 37 Straight running low-back pressure chain Patented design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0821K0750LFAR 190.5 7.50 4.20 2.82 2850 641 LF C0821K1000LFAR 254.0 10.00 5.50 3.70 2850 641 LF C0821K1200LFAR 304.8 12.00 6.50 4.37 2850 641 LF Pin material: stainless steel Standard packaging: 1.524 m = 5ft The weight specification is indicative Roller material: DR (dark blue) Other materials on request Related products Multi-Hub 821 sprocket rims (see page 95) Multi-Hub 881 sprocket rims (2 set-up side-by-side) (see page 97) Multi-Hub inserts (see page 100) Solid sprockets Series 821 (see page 105)

LBP 821 SB (straight) 38 Straight running low-back pressure chain Patented design Third roller row replaced by sliding block Cost efficient solution For wide and stable goods Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0821K0750LFAS 190.5 7.50 3.60 2.42 2850 641 LF C0821K1000LFAS 254.0 10.00 4.70 3.16 2850 641 LF C0821K1200LFAS 304.8 12.00 5.50 3.70 2850 641 LF Pin material: stainless steel Standard packaging: 1.524 m = 5ft The weight specification is indicative Roller material: DR (dark blue) Other materials on request Related products Multi-Hub 821 sprocket rims (see page 95) Multi-Hub 881 sprocket rims (2 set-up side-by-side) (see page 97) Multi-Hub inserts (see page 100) Solid sprockets Series 821 (see page 105)

LBP 882T (radius) 39 Radius running low-back pressure chain Patented design Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0882K0750LFTR 190.5 7.50 4.40 2.96 2850 641 610 24.0 LF C0882K1000LFTR 254.0 10.00 5.30 3.56 2850 641 610 24.0 LF C0882K1200LFTR 304.8 12.00 6.00 4.03 2850 641 610 24.0 LF Pin material: stainless steel Standard packaging: 1.524 m = 5ft The weight specification is indicative Roller material: DR (dark blue) Other materials on request Related products Multi-Hub 882 sprocket rims (see page 98) Multi-Hub inserts (see page 100) Solid sprockets Series 882 (see page 108)

LBP 882T SB (radius) 40 Radius running low-back pressure chain Patented design Third roller row replaced by sliding block Cost efficient solution For wide and stable goods Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C0882K0750LFTS 190.5 7.50 3.90 2.62 2850 641 610 24.0 LF C0882K1000LFTS 254.0 10.00 4.70 3.16 2850 641 610 24.0 LF C0882K1200LFTS 304.8 12.00 5.40 3.63 2850 641 610 24.0 LF Pin material: stainless steel Standard packaging: 1.524 m = 5ft The weight specification is indicative Roller material: DR (dark blue) Other materials on request Related products Multi-Hub 882 sprocket rims (see page 98) Multi-Hub inserts (see page 100) Solid sprockets Series 882 (see page 108)

Slat Top 800 (straight) 41 Straight running steel chain Heavy duty double hinge design = identical sprocket for 800 and 821 series chain For side transfer with 881 series radius running chain Chain data R Plate clearance A Ra Mat erial Habasit code Width W Weight Nominal tensile strength F N b mm inch kg/m lb/ft N lbf mm inch mm inch μm C0800K0750CSAA 190.5 7.50 5.80 3.90 11500 2588 150 5.90 1.6 0.06 CS C0800K0750SSAA 190.5 7.50 5.80 3.90 7000 1575 150 5.90 1.6 0.06 SS C0800K0750SHAA 190.5 7.50 5.80 3.90 9000 2025 150 5.90 1.6 0.06 <0.3 SH C0800K0750SAAA 190.5 7.50 5.80 3.90 8000 1800 150 5.90 1.6 0.06 <0.5 SA Pin material: case hardened carbon steel (for CS chain), stainless steel (for SS, SH and SA chain) Standard packaging: 3.048 m = 10ft The weight specification is indicative Bakery bends available Related products Multi-Hub 821sprocket rims (see page 95) Multi-Hub 881 sprocket rims (2 set-up side-by-side) (see page 97) Multi-Hub inserts (see page 100) Solid sprockets Series 821 (see page 105)

Slat Top 810 (straight) 42 Straight running steel chain For side transfer with 881 series radius running chain Chain data R Plate clearance A Ra Mat erial Habasit code Width W Weight Nominal tensile strength F N b mm inch kg/m lb/ft N lbf mm inch mm inch μm C0810K0225CSAA 57.1 2.25 2.18 1.46 8500 1913 150 5.90 1.6 0.06 CS C0810K0225SSAA 57.1 2.25 2.18 1.46 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0225SHAA 57.1 2.25 2.18 1.46 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0225SAAA 57.1 2.25 2.18 1.46 5500 1238 150 5.90 1.6 0.06 <0.5 SA C0810K0325CSAA 82.6 3.25 2.65 1.78 8500 1913 150 5.90 1.6 0.06 CS C0810K0325SSAA 82.6 3.25 2.65 1.78 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0325SHAA 82.6 3.25 2.65 1.78 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0325SAAA 82.6 3.25 2.65 1.78 5500 1238 150 5.90 1.6 0.06 <0.5 SA C0810K0330SSAA 83.8 3.30 2.67 1.79 5000 1125 150 5.90 1.6 0.06 SS C0810K0330SHAA 83.8 3.30 2.67 1.79 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0400CSAA 101.6 4.00 3.00 2.02 8500 1913 150 5.90 1.6 0.06 CS C0810K0400SSAA 101.6 4.00 3.00 2.02 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0400SHAA 101.6 4.00 3.00 2.02 5000 1125 150 5.90 1.6 0.06 <0.3 SH C0810K0400SAAA 101.6 4.00 3.00 2.02 5500 1238 150 5.90 1.6 0.06 <0.5 SA C0810K0450CSAA 114.3 4.50 3.30 2.22 8500 1913 150 5.90 1.6 0.06 CS C0810K0450SSAA 114.3 4.50 3.30 2.22 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0450SHAA 114.3 4.50 3.30 2.22 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0450SAAA 114.3 4.50 3.30 2.22 5500 1238 150 5.90 1.6 0.06 <0.5 SA C0810K0600CSAA 152.4 6.00 4.20 2.82 8500 1913 150 5.90 1.6 0.06 CS C0810K0600SSAA 152.4 6.00 4.20 2.82 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0600SHAA 152.4 6.00 4.20 2.82 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0600SAAA 152.4 6.00 4.20 2.82 5500 1238 150 5.90 1.6 0.06 <0.5 SA C0810K0750CSAA 190.5 7.50 5.10 3.43 8500 1913 150 5.90 1.6 0.06 CS C0810K0750SSAA 190.5 7.50 5.10 3.43 5000 1125 150 5.90 1.6 0.06 <0.3 SS C0810K0750SHAA 190.5 7.50 5.10 3.43 6000 1350 150 5.90 1.6 0.06 <0.3 SH C0810K0750SAAA 190.5 7.50 5.10 3.43 5500 1238 150 5.90 1.6 0.06 <0.5 SA

Slat Top 810 (straight) 43 Pin material: case hardened carbon steel (for CS chain), stainless steel (for SS, SH and SA chain) Standard packaging: 3.048 m = 10ft The weight specification is indicative Bakery bends available Related products Multi-Hub 820 sprocket rims (see page 93) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 810 (see page 102) Solid sprockets Series 820 (see page 104) Solid idler 810 (see page 103)

Slat Top 881B (radius) 44 Radius running steel bevel chain For side transfer with 800 and 810 series straight running chain Chain data R Ra Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch μm C0881K0325CSBA 82.6 3.25 2.90 1.95 8000 1800 457 18.0 CS C0881K0325SHBA 82.6 3.25 2.90 1.95 5500 1237 457 18.0 <0.3 SH C0881K0325SABA 82.6 3.25 2.90 1.95 5000 1125 457 18.0 <0.5 SA C0881K0450CSBA 114.3 4.50 3.60 2.42 8000 1800 500 19.7 CS C0881K0450SHBA 114.3 4.50 3.60 2.42 5500 1238 500 19.7 <0.3 SH C0881K0450SABA 114.3 4.50 3.60 2.42 5000 1125 500 19.7 <0.5 SA C0881K0750CSBA 190.5 7.50 5.30 3.56 8000 1800 500 19.7 CS C0881K0750SHBA 190.5 7.50 5.30 3.56 5500 1238 500 19.7 <0.3 SH C0881K0750SABA 190.5 7.50 5.30 3.56 5000 1125 500 19.7 <0.5 SA Pin material: case hardened carbon steel (for CS chain), stainless steel (for SH and SA chain) Standard packaging: 3.048 m = 10ft The weight specification is indicative Bakery bends available Related products Multi-Hub 881 sprocket rims (see page 97) Multi-Hub 820 idler rims (see page 94) Multi-Hub inserts (see page 100) Solid sprockets Series 881 (see page 107)

Slat Top 881T (radius) 45 Radius running steel tab chain For side transfer with 800 and 810 series straight running chain Chain data R Ra Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch μm C0881K0325CSTA 82.6 3.25 3.10 2.08 8000 1800 457 18.0 CS C0881K0325SHTA 82.6 3.25 3.10 2.08 5500 1238 457 18.0 <0.3 SH C0881K0325SATA 82.6 3.25 3.10 2.08 5000 1125 457 18.0 <0.5 SA C0881K0450CSTA 114.3 4.50 3.80 2.55 8000 1800 500 19.7 CS C0881K0450SHTA 114.3 4.50 3.80 2.55 5500 1238 500 19.7 <0.3 SH C0881K0450SATA 114.3 4.50 3.80 2.55 5000 1125 500 19.7 <0.5 SA C0881K0750CSTA 190.5 7.50 5.50 3.70 8000 1800 500 19.7 CS C0881K0750SHTA 190.5 7.50 5.50 3.70 5500 1238 500 19.7 <0.3 SH C0881K0750SATA 190.5 7.50 5.50 3.70 5000 1125 500 19.7 <0.5 SA Pin material: case hardened carbon steel (for CS chain), stainless steel (for SH and SA chain) Standard packaging: 3.048 m = 10ft The weight specification is indicative Bakery bends available Related products Multi-Hub 881 sprocket rims (see page 97) Multi-Hub inserts (see page 100) Solid sprockets Series 881 (see page 107)

Slat Top steel accessories 46 So called bakery bends are bended top plates of Slat Top steel chains. Bakery bends are used in the bakery industry for products discharged from ovens. The bended edge ensures a smooth product transfer. Bakery bends are available for 810 and 881T chain type in CS and SA material as indicated in the table below. The top plate of the Slat Top steel chain is will be bended according to the dimensions in the drawing below. Nomenclature: One side bent in travel direction on the right side suffix: -R1 One side bent in travel direction on the left side suffix: -L1 Both sides bent suffix: -RL Slat Top 810 (straight) Chain type C0810K0450CSAA C0810K0600CSAA C0810K0750CSAA C0810K0450SAAA C0810K0600SAAA C0810K0750SAAA Bend angle ( ) a Chain width W A B mm inch mm inch mm inch -R1 18 114.3 4.5 19.1 0.75 6.4 0.25 -L1 18 114.3 4.5 19.1 0.75 6.4 0.25 -RL 18 114.3 4.5 19.1 0.75 6.4 0.25 -R1 14 152.4 6 25.4 1 6.4 0.25 -L1 14 152.4 6 25.4 1 6.4 0.25 -RL 14 152.4 6 25.4 1 6.4 0.25 -R1 14 190.5 7.5 25.4 1 6.4 0.25 -L1 14 190.5 7.5 25.4 1 6.4 0.25 -RL 14 190.5 7.5 25.4 1 6.4 0.25 -R1 18 114.3 4.5 19.1 0.75 6.4 0.25 -L1 18 114.3 4.5 19.1 0.75 6.4 0.25 -RL 18 114.3 4.5 19.1 0.75 6.4 0.25 -R1 14 152.4 6 25.4 1 6.4 0.25 -L1 14 152.4 6 25.4 1 6.4 0.25 -RL 14 152.4 6 25.4 1 6.4 0.25 -R1 14 190.5 7.5 25.4 1 6.4 0.25 -L1 14 190.5 7.5 25.4 1 6.4 0.25 -RL 14 190.5 7.5 25.4 1 6.4 0.25 Slat Top 881T (radius) Chain type C0881K0450CSTA C0881K0750CSTA C0881K0450SATA C0881K0750SATA Extension Extension Bend angle ( ) a Chain width W A B mm inch mm inch mm inch -R1 18 114.3 4.5 19.1 0.75 6.4 0.25 -L1 18 114.3 4.5 19.1 0.75 6.4 0.25 -RL 18 114.3 4.5 19.1 0.75 6.4 0.25 -R1 14 190.5 7.5 25.4 1 6.4 0.25 -L1 14 190.5 7.5 25.4 1 6.4 0.25 -RL 14 190.5 7.5 25.4 1 6.4 0.25 -R1 18 114.3 4.5 19.1 0.75 6.4 0.25 -L1 18 114.3 4.5 19.1 0.75 6.4 0.25 -RL 18 114.3 4.5 19.1 0.75 6.4 0.25 -R1 14 190.5 7.5 25.4 1 6.4 0.25 -L1 14 190.5 7.5 25.4 1 6.4 0.25 -RL 14 190.5 7.5 25.4 1 6.4 0.25

Flexi 7100HA 47 Radius running conveyor system plastic chain Easy assembly and disassembly Openings for cleaning with compressed air Capable to run on corner discs For conveyor layouts requiring tight turns Chain data Habasit code Width W Weight Nominal tensile strength F N C E F G R b mm inch kg/m lb/ft N lbf mm inch mm inch mm inch mm inch mm inch C7100P0248LFHA 63.0 2.48 0.73 0.49 500 113 21.1 0.83 3.6 0.14 7.1 0.28 7.9 0.31 70 2.76 C7100P0248PTHA 63.0 2.48 0.73 0.49 500 113 21.1 0.83 3.6 0.14 7.1 0.28 7.9 0.31 70 2.76 C7100K0325LFHA 83.0 3.27 1.19 0.80 1250 281 35.6 1.40 3.8 0.15 7.1 0.28 11.1 0.44 90 3.54 C7100K0325PTHA 83.0 3.27 1.19 0.80 1250 281 35.6 1.40 3.8 0.15 7.1 0.28 11.1 0.44 90 3.54 C7100K0405LFHA 103.0 4.05 1.64 1.11 1250 281 46.0 1.81 4.8 0.19 7.1 0.28 12.1 0.48 100 3.94 C7100K0405PTHA 103.0 4.05 1.64 1.11 1250 281 46.0 1.81 4.8 0.19 7.1 0.28 12.1 0.48 100 3.94 Habasit code R s P T Mat erial mm inch mm inch mm inch C7100P0248LFHA 150.0 5.91 25.4 1.00 37.1 1.46 LF C7100P0248PTHA 150.0 5.91 25.4 1.00 37.1 1.46 PT C7100K0325LFHA 160.0 6.30 33.5 1.32 58.1 2.29 LF C7100K0325PTHA 160.0 6.30 33.5 1.32 58.1 2.29 PT C7100K0405LFHA 170.0 6.69 35.5 1.40 77.5 3.05 LF C7100K0405PTHA 170.0 6.69 35.5 1.40 77.5 3.05 PT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 7100 (see page 116) Solid idlers Series 7100 (see page 117) HabiPLAST wear strip FL W 15.5x6.1

Snap-on 843 (straight) 48 Straight running snap-on chain Steel base roller chain with snap-on plastic top plates Base chain: 0.5" pitch 843 roller chain Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0843S0138DPAA 35.0 1.38 0.83 0.56 2500 563 DP C0843S0138LFAA 35.0 1.38 0.83 0.56 2500 563 LF C0843S0138PTAA 35.0 1.38 0.83 0.56 2500 563 PT C0843S0144DPAA 36.6 1.44 0.83 0.56 2500 563 DP C0843S0144LFAA 36.6 1.44 0.83 0.56 2500 563 LF C0843S0144PTAA 36.6 1.44 0.83 0.56 2500 563 PT C0843S0200DPAA 50.8 2.00 0.89 0.60 2500 563 DP C0843S0200LFAA 50.8 2.00 0.89 0.60 2500 563 LF C0843S0200PTAA 50.8 2.00 0.89 0.60 2500 563 PT C0843S0325DPAA 82.6 3.25 10.30 6.92 2500 563 DP C0843S0325LFAA 82.6 3.25 10.30 6.92 2500 563 LF C0843S0325PTAA 82.6 3.25 10.30 6.92 2500 563 PT Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 1800 N (400 lbf) Nomenclature for base chain only: - C0843B0050CS - C0843B0050SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 40-1 series roller chain sprockets

Snap-on 843C (straight) 49 Straight running snap-on chain Steel base roller chain with snap-on plastic top plates Base chain: 0.5" pitch 843 roller chain Chamfered top plates Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C843CS0138DPAA 35.0 1.38 0.86 0.58 2500 563 DP C843CS0138LFAA 35.0 1.38 0.86 0.58 2500 563 LF C843CS0138PTAA 35.0 1.38 0.86 0.58 2500 563 PT C843CS0200DPAA 50.8 2.00 0.92 0.62 2500 563 DP C843CS0200LFAA 50.8 2.00 0.92 0.62 2500 563 LF C843CS0200PTAA 50.8 2.00 0.92 0.62 2500 563 PT C843CS0325DPAA 82.6 3.25 1.06 0.71 2500 563 DP C843CS0325LFAA 82.6 3.25 1.06 0.71 2500 563 LF C843CS0325PTAA 82.6 3.25 1.06 0.71 2500 563 PT Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 1800 N (400 lbf) Nomenclature for base chain only: - C0843B0050CS - C0843B0050SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 40-1 series roller chain sprockets

Snap-on 863 (straight) 50 Straight running snap-on chain Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 863 roller chain Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0863S0325DPAA 82.6 3.25 2.10 1.41 5000 1125 DP C0863S0325LFAA 82.6 3.25 2.10 1.41 5000 1125 LF C0863S0450DPAA 114.3 4.50 2.30 1.55 5000 1125 DP C0863S0450LFAA 114.3 4.50 2.30 1.55 5000 1125 LF C0863S0600DPAA 152.4 6.00 2.53 1.70 5000 1125 DP C0863S0600LFAA 152.4 6.00 2.53 1.70 5000 1125 LF C0863S0750DPAA 190.5 7.50 2.68 1.80 5000 1125 DP C0863S0750LFAA 190.5 7.50 2.68 1.80 5000 1125 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 3000 N (675 lbf) Nomenclature for base chain only: - C0863B0075CS - C0863B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 863T (straight) 51 Straight running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 863 roller chain Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0863S0250DPTA 63.5 2.50 2.10 1.41 5000 1125 DP C0863S0250LFTA 63.5 2.50 2.10 1.41 5000 1125 LF C0863S0325DPTA 82.6 3.25 2.19 1.47 5000 1125 DP C0863S0325LFTA 82.6 3.25 2.19 1.47 5000 1125 LF C0863S0450DPTA 114.3 4.50 2.37 1.59 5000 1125 DP C0863S0450LFTA 114.3 4.50 2.37 1.59 5000 1125 LF C0863S0500DPTA 127.0 5.00 2.41 1.62 5000 1125 DP C0863S0500LFTA 127.0 5.00 2.41 1.62 5000 1125 LF C0863S0750DPTA 190.5 7.50 2.71 1.82 5000 1125 DP C0863S0750LFTA 190.5 7.50 2.71 1.82 5000 1125 LF C0863S1000DPTA 254.0 10.00 3.17 2.13 5000 1125 DP C0863S1000LFTA 254.0 10.00 3.17 2.13 5000 1125 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 3000 N (675 lbf) Nomenclature for base chain only: - C0863B0075CS - C0863B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 963 (straight) 52 Straight running snap-on chain Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0963S0325DPAA 82.6 3.25 2.10 1.41 4000 900 DP C0963S0325LFAA 82.6 3.25 2.10 1.41 4000 900 LF C0963S0450DPAA 114.3 4.50 2.30 1.55 4000 900 DP C0963S0450LFAA 114.3 4.50 2.30 1.55 4000 900 LF C0963S0600DPAA 152.4 6.00 2.53 1.70 4000 900 DP C0963S0600LFAA 152.4 6.00 2.53 1.70 4000 900 LF C0963S0750DPAA 190.5 7.50 2.68 1.80 4000 900 DP C0963S0750LFAA 190.5 7.50 2.68 1.80 4000 900 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 963T (straight) 53 Straight running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0963S0250DPTA 63.5 2.50 2.10 1.41 4000 900 DP C0963S0250LFTA 63.5 2.50 2.10 1.41 4000 900 LF C0963S0325DPTA 82.6 3.25 2.19 1.47 4000 900 DP C0963S0325LFTA 82.6 3.25 2.19 1.47 4000 900 LF C0963S0450DPTA 114.3 4.50 2.37 1.59 4000 900 DP C0963S0450LFTA 114.3 4.50 2.37 1.59 4000 900 LF C0963S0500DPTA 127.0 5.00 2.41 1.62 4000 900 DP C0963S0500LFTA 127.0 5.00 2.41 1.62 4000 900 LF C0963S0750DPTA 190.5 7.50 2.71 1.82 4000 900 DP C0963S0750LFTA 190.5 7.50 2.71 1.82 4000 900 LF C0963S1000DPTA 254.0 10.00 3.17 2.13 4000 900 DP C0963S1000LFTA 254.0 10.00 3.17 2.13 4000 900 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft ( including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 1843T (radius) 54 Radius running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.5" pitch 1843 roller chain Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C1843S0125DPTA 31.7 1.25 0.83 0.56 2500 563 22.4 0.88 21.3 0.84 315 12.4 DP C1843S0125LFTA 31.7 1.25 0.83 0.56 2500 563 22.4 0.88 21.3 0.84 315 12.4 LF C1843S0125PTTA 31.7 1.25 0.83 0.56 2500 563 22.4 0.88 21.3 0.84 315 12.4 PT C1843S0150DPTA 38.1 1.50 0.85 0.57 2500 563 22.4 0.88 21.3 0.84 315 12.4 DP C1843S0150LFTA 38.1 1.50 0.85 0.57 2500 563 22.4 0.88 21.3 0.84 315 12.4 LF C1843S0150PTTA 38.1 1.50 0.85 0.57 2500 563 22.4 0.88 21.3 0.84 315 12.4 PT C1843S0200DPTA 50.8 2.00 0.90 0.60 2500 563 22.4 0.88 21.3 0.84 315 12.4 DP C1843S0200LFTA 50.8 2.00 0.90 0.60 2500 563 22.4 0.88 21.3 0.84 315 12.4 LF C1843S0200PTTA 50.8 2.00 0.90 0.60 2500 563 22.4 0.88 21.3 0.84 315 12.4 PT C1843S0325DPTA 82.6 3.25 1.02 0.69 2500 563 22.4 0.88 21.3 0.84 315 12.4 DP C1843S0325LFTA 82.6 3.25 1.02 0.69 2500 563 22.4 0.88 21.3 0.84 315 12.4 LF C1843S0325PTTA 82.6 3.25 1.02 0.69 2500 563 22.4 0.88 21.3 0.84 315 12.4 PT Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 1800 N (400 lbf) Nomenclature for base chain only: - C1843B0050CS - C1843B0050SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 40-1 series roller chain sprockets

Snap-on 1873T (radius) 55 Radius running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Designed for bi-directional travel Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C1873S0225DPTA 57.2 2.25 1.97 1.32 4000 900 33.3 1.31 35.1 1.38 356 14.0 DP C1873S0225LFTA 57.2 2.25 1.97 1.32 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF C1873S0250DPTA 63.5 2.50 2.00 1.34 4000 900 33.3 1.31 35.1 1.38 356 14.0 DP C1873S0250LFTA 63.5 2.50 2.00 1.34 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF C1873S0325DPTA 82.6 3.25 2.10 1.41 4000 900 33.3 1.31 35.1 1.38 356 14.0 DP C1873S0325LFTA 82.6 3.25 2.10 1.41 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF C1873S0450DPTA 114.3 4.50 2.26 1.52 4000 900 33.3 1.31 35.1 1.38 356 14.0 DP C1873S0450LFTA 114.3 4.50 2.26 1.52 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF C1873S0600DPTA 152.4 6.00 2.41 1.62 4000 900 33.3 1.31 35.1 1.38 457 18.0 DP C1873S0600LFTA 152.4 6.00 2.41 1.62 4000 900 33.3 1.31 35.1 1.38 457 18.0 LF C1873S0750DPTA 190.5 7.50 2.56 1.72 4000 900 33.3 1.31 35.1 1.38 457 18.0 DP C1873S0750LFTA 190.5 7.50 2.56 1.72 4000 900 33.3 1.31 35.1 1.38 457 18.0 LF C1873S1000DPTA 254.0 10.00 2.78 1.87 4000 900 33.3 1.31 35.1 1.38 457 18.0 DP C1873S1000LFTA 254.0 10.00 2.78 1.87 4000 900 33.3 1.31 35.1 1.38 457 18.0 LF C1873S1200DPTA 304.8 12.00 3.01 2.02 4000 900 33.3 1.31 35.1 1.38 457 18.0 DP C1873S1200LFTA 304.8 12.00 3.01 2.02 4000 900 33.3 1.31 35.1 1.38 457 18.0 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 1873T-T (straight) 56 Straight running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1873S0325DPTA-T 82.6 3.25 2.14 1.44 4000 900 DP C1873S0325LFTA-T 82.6 3.25 2.14 1.44 4000 900 LF C1873S0450DPTA-T 114.3 4.50 2.32 1.56 4000 900 DP C1873S0450LFTA-T 114.3 4.50 2.32 1.56 4000 900 LF C1873S0600DPTA-T 152.4 6.00 2.53 1.70 4000 900 DP C1873S0600LFTA-T 152.4 6.00 2.53 1.70 4000 900 LF C1873S0750DPTA-T 190.5 7.50 2.74 1.84 4000 900 DP C1873S0750LFTA-T 190.5 7.50 2.74 1.84 4000 900 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 1873-D1 (radius) 57 Radius running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain D style gripper inserts Designed for bi-directional travel Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C1873S0375LFTG-D1 95.3 3.75 2.90 1.95 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Driven by standard ANSI 60-1 series roller chain sprockets Only available in 73 Shore A hardness Stardard material for gripper is PL black Top plates may be purchased separately White color is available on request

Snap-on 1873-L4 (radius) 58 Radius running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Four finger style gripper inserts Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C1873S0375LFTG-L4 95.3 3.75 2.80 1.88 4000 900 33.3 1.31 35.1 1.38 356 14.0 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Driven by standard ANSI 60-1 series roller chain sprockets Only available in 73 Shore A hardness Standard material for gripper is PL white Top plates may be purchased separately Black color is available on request

Snap-on 1874T (radius) 59 Radius running snap-on chain with tab Steel base roller chain with snap-on steel top plates Base chain: 0.75" pitch 1873 roller chain Designed for bi-directional travel For applications with high temperatures and / or abrasive materials Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C1874S0325CSTA 82.6 3.25 4.20 2.82 4000 900 34.1 1.34 34.6 1.36 356 14.0 CS C1874S0450CSTA 114.3 4.50 4.80 3.25 4000 900 34.1 1.34 34.6 1.36 356 14.0 CS C1874S0600CSTA 152.4 6.00 5.70 3.83 4000 900 34.1 1.34 34.6 1.36 457 16.0 CS C1874S0750CSTA 190.5 7.50 6.40 4.30 4000 900 34.1 1.34 34.6 1.36 610 24.0 CS Base chain: Standard material is CS Nomenclature for base chain only: - C1873B0075CS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on 3873T (radius) 60 Radius running snap-on chain with tab Steel base roller chain with snap-on plastic top plates Base chain: 0.75" pitch 1873 roller chain Overlapping top plates ensure that nothing can get caught between Chain data J (straight) J (curve) R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch mm inch mm inch C3873S1000DPTA 254.0 10.00 3.47 2.33 4000 900 33.3 1.31 35.1 1.38 457 18.0 DP C3873S1000LFTA 254.0 10.00 3.47 2.33 4000 900 33.3 1.31 35.1 1.38 457 18.0 LF Base chain: Standard material is CS Stainless steel (SS) on request: Max. workload 2'000 N (450 lbf) Nomenclature for base chain only: - C1873B0075CS - C1873B0075SS Standard packaging: 3.048 m = 10ft (including one connecting link) The weight specification is indicative Other top plate material available on request Top plates may be purchased separately Driven by standard ANSI 60-1 series roller chain sprockets

Snap-on accessories 61 Inserts Custom inserts can be fitted into most Snap-on Chain types to increase the friction between product and chain. This is beneficial for incline or decline applications. Standard insert material is PL (other materials like HY on request) Chain links with inserts can be ordered either individually or ready-built into chain lengths (standard packaging: 3.048 m = 10 ft) For order code of special building pattern see page Nomenclature Standard insert dimensions are shown in the table below Chain type Chain width Insert type Insert width L mm inch 325 60 2.36 450 105 4.13 863 / 963 XA 600 130 5.12 750 325 60 2.36 450 90 3.54 1873T 600 XA 750 130 5.12 1000 200 7.87 1200 XB 295 11.61 Type XA Type XB This is only a brief overview of our inserts. Many different insert designs are available. For further information and availability please contact your local Habasit partner. Loose Snap-on plastic top plates are available on request (suffix TP). Minimum delivery is 25 pieces. Connecting links are available on request For order code see page "Nomenclature"

Multiflex 1700 (radius) 62 Multiflex plastic chain with wide top plate Capable to run on corner discs For conveyor layouts requiring tight turns Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1700K0217LFAA 55.0 2.17 1.28 0.86 2600 584 LF Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1700 (see page 114) Turning discs

Multiflex 1701T (radius) 63 Multiflex plastic chain with tab Capable to run on corner discs For conveyor layouts requiring tight turns Chain data J (straight) J (curve) Mat erial Habasit code Width W Weight Nominal tensile strength F N mm inch kg/m lb/ft N lbf mm inch mm inch C1701K0209LFTA 53.2 2.09 1.34 0.9 2600 584 59.5 2.34 57.2 2.25 LF Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprocket Series 1700 (see page 114) Turning discs

Multiflex 1702 (radius) 64 Multiflex plastic chain without tab Capable to run on corner discs For conveyor layouts requiring tight turns Chain data J (straight) J (curve) Mat erial Habasit code Width W Weight Nominal tensile strength F N mm inch kg/m lb/ft N lbf mm inch mm inch C1702K0209LFAA 53.2 2.09 1.29 0.87 2600 584 62.0 2.44 59.6 2.35 LF Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprocket Series 1700 (see page 114) Turning discs

Multiflex chain accessories 65 Extended pivots and inserts can be fitted to the multiflex range of chains. Inserts are benifical for incline or decline applications where the extended pivots can be used for a variety of applications where the product is required to be spaced, held or pushed where the stand alone chain is not sufficient. Both inserts and extended pivots are available in standard arrangements as well as to customer requirements. Extended pivot Insert Standard accessories Chain type Accessory type mm Dimension H inch Standard material C1700 C1701T C1702 C1700 C1701T C1702 26.5 1.04 Extended pivot 25.5 1.00 Insert POM white see material overview Custom dimensions and arrangements available by request.

Case chain 40P (straight) 66 Small straight running plastic chain with closed top plate Driven by standard 0.5" (12.7 mm) pitch steel roller chain sprocket For applications requiring a closed top plate design that eliminates pinch points Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0040P0079DPAA-001 20.0 0.79 0.36 0.24 445 100 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Driven by standard ANSI 40-1 roller chain sprockets

Case chain 60P (straight) 67 Small straight running plastic chain with closed top plate Driven by standard 0.75" (19.1 mm) pitch steel roller chain sprocket For applications requiring a closed top plate design that eliminates pinch points Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0060P0118DPAA-001 30.0 1.18 0.71 0.48 890 200 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Driven by standard ANSI 60-1 roller chain sprockets

Case chain 600 (radius) 68 Radius running plastic chain Closed top design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0600P0169DPAA-001 42.0 1.65 1.10 0.74 4500 1012 DP Pin material: stainless steel Standard packaging: 6.096 m = 20ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 600 (see page 101)

Case chain 601 (radius) 69 Radius running plastic chain Open top design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0601P0169DPAA-001 42.0 1.65 1.05 0.71 4500 1012 DP Pin material: stainless steel Standard packaging: 6.096 m = 20ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 600 (see page 101)

Case chain 610T (radius) 70 Radius running plastic tab chain Closed top design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0610P0169DPTA-001 42.0 1.65 1.15 0.77 4500 1012 DP Pin material: stainless steel Standard packaging: 6.096 m = 20ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 600 (see page 101)

Case chain 611T (radius) 71 Radius running plastic tab chain Open top design The tab shape is different compared to 611TE Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0611P0169DPTA-001 42.0 1.65 1.10 0.74 4500 1012 DP Pin material: stainless steel Standard packaging: 6.096 m = 20ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 600 (see page 101)

Case chain 611TE (radius) 72 Radius running plastic tab chain Open top design The tab shape is different compared to 611T Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C0611P0169DPTE-001 43.0 1.69 1.10 0.74 4500 1012 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 600 (see page 101)

Case chain 1100 (straight) 73 Straight running plastic chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1100P0100DPAA 25.4 1.00 0.30 0.20 623 140 DP C1100P0100NYAA 25.4 1.00 0.29 0.20 623 140 NY C1100P0100HTAA 25.4 1.00 0.29 0.20 623 140 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Available with various chain attachments including extended pins Related products Solid sprockets Series 1100 (see page 109)

Case chain 1110T (radius) 74 Radius running plastic tab chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1110P0100DPTA 25.4 1.00 0.31 0.21 373 84 DP C1110P0100NYTA 25.4 1.00 0.30 0.20 373 84 NY C1110P0100HTTA 25.4 1.00 0.30 0.20 373 84 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1100 (see page 109)

Case chain 1150 (straight) 75 Straight running plastic chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1150P0165HTAA 41.9 1.65 0.65 0.44 1379 310 HT C1150P0165PCAA 41.9 1.65 0.68 0.46 1379 310 PC Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Available with various chain accessories including extended pins Related products Solid sprockets Series 1150 (see page 110)

Case chain 1151T (radius) 76 Radius running plastic tab chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1151P0165HTTA 41.9 1.65 0.66 0.44 827 186 HT C1151P0165PCTA 41.9 1.65 0.69 0.47 827 186 PC Pin material: stainless steel Standard packaging: 3.048 m = 10 ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1150 (see page 110)

Case chain 1200 (straight) 77 Straight running plastic chain The 1200 series is identical to the 3200 series except for the material variety and the available accessories Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1200P0224DPAA 57.0 2.24 1.30 0.87 3100 698 DP C1200P0224HTAA 57.0 2.24 1.30 0.87 3100 698 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft Other materials on request The weight specification is indicative Related products Solid sprockets Series 1200 (see page 111)

Case chain 1201AB (straight) 78 Perforated flat top design Tapered slots for reduced trapping of conveyed product Safety version for pinch protection Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1201P0224DPAB-00N 57.0 2.24 1.51 1.01 3100 698 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft Other materials on request The weight specification is indicative Related products Solid sprockets Series 1200 (see page 111)

Case chain 1210T (radius) 79 Radius running plastic tab chain The 1210T series is identical to the 3210T series except for the material variety, the sideflexing radius and the available accessories Designed for bi-directional travel Chain data R Mat erial Habasit code Width W Weight Nominal tensile strength F N s mm inch kg/m lb/ft N lbf mm inch C1210P0224DPTA 57.0 2.24 1.35 0.91 2500 563 457 18.0 DP C1210P0224HTTA 57.0 2.24 1.35 0.91 2500 563 457 18.0 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1200 (see page 111)

Case chain 1211TB (radius) 80 Radius running plastic tab chain Perforated flat top design Tapered slots for reduced trapping of conveyed product Safety version for pinch protection Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1211P0224DPTB-00N 57.0 2.24 1.51 1.01 3100 698 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft Other materials on request The weight specification is indicative Related products Solid sprockets Series 1200 (see page 111)

Case chain 1250 (straight) 81 Straight running plastic chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1250P0225HTAA 57.2 2.25 1.73 1.16 6228 1400 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Available with various chain attachments including extended pins Related products Solid sprockets Series 1250 (see page 112)

Case chain 1251T (radius) 82 Radius running plastic tab chain Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1251P0225HTTA 57.2 2.25 1.73 1.16 3700 833 HT Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1250 (see page 112)

Case chain 1400 (radius) 83 Radius running plastic chain Open top design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1400P0200DPAA-001 50.8 2.00 2.08 1.40 6600 1485 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1400 (see page 113)

Case chain 1410T (radius) 84 Radius running plastic tab chain Open top design Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C1410P0200DPTA-001 50.8 2.00 2.27 1.53 6600 1485 DP Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 1400 (see page 113)

Case chain 3200 (straight) 85 Straight running plastic chain The 3200 series is identical to the 1200 series except for the material variety and the available accessories Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C3200K0224DPAA-001 57.0 2.24 1.30 0.87 3100 698 DP C3200K0224DPAA-002 57.0 2.24 1.30 0.87 3100 698 DP C3200K0224DPAA-008 57.0 2.24 1.30 0.87 3100 698 DP C3200K0224NYAA-008 57.0 2.24 1.06 0.71 3100 698 NY Pin material: stainless steel Standard packaging: 3.048 m = 10ft Other materials on request The weight specification is indicative Related products Solid sprockets Series 3200 (see page 115)

Case chain 3210T (radius) 86 Radius running plastic tab chain The 3210T series is identical to the 1210T series except for the material variety, the sideflexing radius and the available accessories Designed for bi-directional travel Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf C3210K0224DPTA-001 57.0 2.24 1.35 0.91 2500 563 DP C3210K0224DPTA-002 57.0 2.24 1.35 0.91 2500 563 DP C3210K0224DPTA-008 57.0 2.24 1.35 0.91 2500 563 DP C3210K0224NYTA-008 57.0 2.24 1.13 0.75 2500 563 NY Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Related products Solid sprockets Series 3200 (see page 115)

Case chain NH78 (straight) 87 Straight running plastic chain Designed for bi-directional travel Robust heavy duty design for demanding applications like sewage treatment Chain data Habasit code Width W Weight Nominal tensile strength F N Mat erial mm inch kg/m lb/ft N lbf CNH78P0291LFAA 74.0 2.91 2.10 1.41 7700 1733 LF Pin material: stainless steel Standard packaging: 3.048 m = 10ft The weight specification is indicative Other materials on request Available with various extended pin configurations Related products Solid sprockets Series NH78 (see page 118)

Case chain accessories 88 Different accessories for case chains are available, including extended pins, pushers and attachment points. Extended pin EP (only for straight running chains) Extended journal pins (standard material is stainless steel SA) are particularly advantageous for low tension accumulation, eliminating damage to product and containers. Chain type Chain pitch P Pin diam. D Pin length L mm inch mm inch mm inch C1100K100EP--AA---1 25.4 1.00 6.4 1/4 = 0.25 C1150K165EP--AA---1 38.1 1.50 6.4 1/4 = 0.25 C1200K224EP--AA---3 9.5 3/8 = 0.38 50.8 2.00 C1200K224EP--AA---8 12.7 8/16 = 0.50 C1250K225EP--AA---7 11.1 7/16 = 0.44 63.5 2.50 C1250K225EP--AA---8 12.7 8/16 = 0.50 CNH78K291EP--AA---7 11.11 7/16 = 0.44 CNH78K291EP--AA---8 66.3 2.61 12.7 8/16 = 0.50 CNH78K291EP--AA---9 14.3 9/16 = 0.56 38.1 1.50 Half round pusher HR Ideally suited for indexing, elevating or lowering boxes. Chain type Chain pitch P mm inch C1200K224HR--AA--- 50.8 2.00 For order code of special building pattern see page Nomenclature

Case chain accessories 89 Stainless steel attachment K1 These 303 stainless steel attachments are attached to the chain through the connecting pins. They are suitable for heavy-duty applications and are ideal for attaching slats, pushers or other accessories. Chain pitch P A B C Chain type mm inch mm inch mm inch mm inch C1100K100K1--AA--- 25.4 1.00 15.9 0.63 1.9 0.07 C1150K165K1--AA--- 38.1 1.50 6.9 0.27 19.1 0.75 C1200K224K1--AA--- 50.8 2.00 28.9 1.14 2.7 0.11 Chain type D E F G mm inch mm inch mm inch mm inch C1100K100K1--AA--- 11.5 0.45 4.1 0.16 10.9 0.43 18 0.71 C1150K165K1--AA--- 17.5 0.69 6.9 0.27 12.1 0.48 21 0.83 C1200K224K1--AA--- 20.3 0.80 7.5 0.29 15.2 0.60 28.9 1.14 Tab type K2 Molded tab on both sides with two holes. Chain type C1200K224K2--AA--- C1200K224K2--AA--- Chain pitch P mm inch 50.8 2.00 For order code of special building pattern see page Nomenclature

Case chain accessories 90 Tab type A1 Molded tab on one side with one hole. Chain type Chain pitch P A B C mm inch mm inch mm inch mm inch C1100K100A1--AA--- 25.4 1.00 10.4 0.41 10.9 0.43 2.3 0.09 C1150K165A1--AA--- 38.1 1.00 15.2 0.60 18.8 0.74 5.1 0.20 C1200K224A1--AA--- 50.8 2.00 17.5 0.69 19.3 0.76 6.4 0.25 C1250K225A1--AA--- 63.5 2.50 19.1 0.75 29 1.14 7.4 0.29 Chain type D E F G mm inch mm inch mm inch mm inch C1100K100A1--AA--- 11.4 0.45 5.2 0.21 4.1 0.16 3.2 0.13 C1150K165A1--AA--- 17.5 0.69 7.6 0.30 6.0 0.24 5.1 0.20 C1200K224A1--AA--- 20.3 0.80 8.8 0.35 6.8 0.27 6.4 0.25 C1250K225A1--AA--- 31.8 1.25 9.6 0.38 12.5 0.49 6.4 0.25 Tab type A2 Molded tab on both sides with one hole. Chain type Chain pitch P A B C mm inch mm inch mm inch mm inch C1200K224A2--AA--- 50.8 2.00 17.5 0.69 19.3 0.76 6.4 0.25 C1250K225A2--AA--- 63.5 2.50 19.1 0.75 29 1.14 7.4 0.29 Chain type D E F G mm inch mm inch mm inch mm inch C1200K224A2--AA--- 20.3 0.80 8.8 0.35 6.8 0.27 6.4 0.25 C1250K225A2--AA--- 31.8 1.25 9.6 0.38 12.5 0.49 6.4 0.25 For order code of special building pattern see page Nomenclature

Case chain accessories 91 Cone attachment CT Cone Line Module for case chain 1200 (Straight). Standard material is NY white Chain type Chain pitch P 0.75" thread diam. A Thread length min. mm inch mm inch mm inch C1200K224CT--AA--- 50.8 2.00 19.1 0.75 25.4 1.00 For order code of special building pattern see page Nomenclature

Multi-Hub sprockets and idlers 92 Habasit has invented a new type of modular split sprockets and split idlers called Multi-Hub. Interchangeable hub inserts in various diameters with or without keyway and sprocket, or idler rims in two different materials, reduce the inventory needed by customers. With this Multi-Hub system it is possible to combine a noise dampening sprocket rim with a stiff and wear resistant hub. The customized choice of materials and high fabrication accuracy ensure long lifetime and optimized power transmission. Complete Multi-Hub sprocket in noise dampening material ND 1. 2. 3. 4. 5. 1. Complete Multi-Hub sprocket 2. Interchangeable idler rim with screws 3. Interchangeable sprocket rim with screws 4. Interchangeable hub insert: round bore with keyway for drive applications 5. Interchangeable hub insert: plain round bore for idler applications For imperial shaft sizes hub inserts with set screw are available on request.

Multi-Hub 820 sprocket rims 93 Multi-Hub 820 sprocket rim is suitable for 810, 820 and 831 series chains The split sprocket rim has molded guide rings Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0820G218 21 128.9 5.07 129.3 5.09 GS C0820G238 23 142.0 5.59 141.2 5.56 GS C0820G258 25 153.8 6.06 153.2 6.03 GS C0820G217 21 128.9 5.07 129.3 5.09 ND C0820G237 23 142.0 5.59 141.2 5.56 ND C0820G257 25 153.8 6.06 153.2 6.03 ND Included in delivery: 2 sprocket rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub 820 idler rims 94 Multi-Hub 820 idler rim is suitable for all 810, 820, 828, 831, 879B, 880B, 880J, 880LJ, 880M, 881B and 1061M series chains Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Equivalent number of teeth Ø DE Mat erial mm inch C0820L219 21 130.0 5.12 L C0820L239 23 142.5 5.61 L C0820L259 25 154.5 6.08 L Included in delivery: 2 idler rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel Related products Multi-Hub inserts (see page 100) Retainer rings (see page 120)

Multi-Hub 821 sprocket rims 95 Multi-Hub 821 sprocket rim is suitable for 800 and 821 series chains Consisting of two Multi-Hub 881 sprockets set up side-by-side Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0821G258 25 153.8 6.06 153.2 6.03 GS C0821G257 25 153.8 6.06 153.2 6.03 ND Included in delivery: 4 sprocket rim halves (881 type), 8 screws, 8 self-locking nuts Nuts and screws: stainless steel Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub 880 sprocket rims 96 Multi-Hub 880 sprocket rim is suitable for 828, 879, 880 and 890 series chains Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0880G108 10 122.2 4.81 123.3 4.85 GS C0880G128 12 147.4 5.80 147.2 5.80 GS C0880G107 10 122.2 4.81 123.3 4.85 ND C0880G127 12 147.4 5.80 147.2 5.80 ND Included in delivery: 2 sprocket rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub 881 sprocket rims 97 Multi-Hub 881 sprocket rim is suitable for 881 series chains Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0881G258 25 153.8 6.06 153.2 6.03 GS C0881G257 25 153.8 6.06 153.2 6.03 ND Included in delivery: 2 sprocket rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub 882 sprocket rims 98 Multi-Hub 882 sprocket rim is suitable for 882 series chains Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0882G128 12 150.0 5.91 147.2 5.80 GS C0882G127 12 150.0 5.91 147.2 5.80 ND Included in delivery: 2 sprocket rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel. Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub 1060 sprocket rims 99 Multi-Hub 1060 sprocket rim is suitable for 770 and 1061 series chains Different bore configurations can be obtained by using separate Multi-Hub inserts Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C1060G168 16 133.0 5.24 130.2 5.13 GS C1060G188 18 149.2 5.87 146.3 5.76 GS C1060G167 16 133.0 5.24 130.2 5.13 ND C1060G187 18 149.2 5.87 146.3 5.76 ND Included in delivery: 2 sprocket rim halves, 4 screws, 4 self-locking nuts Nuts and screws: stainless steel Special noise dampening material available: ND Related products Multi-Hub inserts (see page 100)

Multi-Hub inserts 100 Available with round bore only (RL type) or with metric keyway according to ISO standard or imperial keyway according to ANSI standard (RZ type) or square bore (QZS type) RZ types are designed to clamp on standard shafts and are suitable for drive applications with all Multi-Hub sprocket rims QZS types need retainer rings for axial fixation. RL types are designed to spin free on standard shafts RL types consist of extra low friction POM (Acetal) material for optimal sliding properties RL type inserts can be used for Multi-Hub sprocket rims (intended to be used as an idler) and Multi-Hub idler rims Set screw fixation option for imperial bores only. Sprocket data Habasit code Insert type Bore size d b t Bore shape Mat erial mm inch mm inch mm inch H025RZ-8 Drive 25.0 8.0 28.3 Round with keyway GS H030RZ-8 Drive 30.0 8.0 33.3 Round with keyway GS H035RZ-8 Drive 35.0 10.0 38.3 Round with keyway GS H040RZ-8 Drive 40.0 12.0 43.3 Round with keyway GS H040QZS84 Drive 40.0 Square GS H100RZ-8 Drive 1 0.25 1.12 Round with keyway GS H125RZ-8 Drive 1 1/4 0.25 1.37 Round with keyway GS H144RZ-8 Drive 1 7/16 0.38 1.61 Round with keyway GS H150RZ-8 Drive 1 1/2 0.38 1.67 Round with keyway GS H150QZS84 Drive 1 1/2 Square GS H025RL Idler 25.0 Round L H030RL Idler 30.0 Round L H035RL Idler 35.0 Round L H040RL Idler 40.0 Round L H100RL Idler 1 Round L H125RL Idler 1 1/4 Round L H144RL Idler 1 7/16 Round L H150RL Idler 1 1/2 Round L

Solid sprockets Series 600 101 Solid sprocket 600 is suitable for all 600 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0600M06PE 6 128.0 5.04 127.0 5.00 PE C0600M08PE 8 168.9 6.65 165.9 6.53 PE C0600M10PE 10 210.1 8.29 205.5 8.09 PE C0600M12PE 12 248.3 9.78 245.3 9.66 PE C0600M14PE 14 288.4 11.35 285.4 11.24 PE Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1 ¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Solid sprockets Series 810 102 Solid sprocket 810 is suitable for all 810 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p L Pilot bore size Ø PB Mat erial mm inch mm inch mm inch mm inch C0810M19NY 19 117.1 4.61 117.4 4.62 42.9 1.69 19.0 0.75 NY C0810M21CI 21 130.1 5.12 129.3 5.09 43.5 1.71 20.0 0.79 CI C0810M21NY 21 130.1 5.12 129.3 5.09 42.9 1.69 19.0 0.75 NY C0810M23CI 23 142.0 5.59 141.2 5.56 43.5 1.71 20.0 0.79 CI C0810M23NY 23 142.0 5.59 141.2 5.56 42.9 1.69 19.0 0.75 NY C0810M25CI 25 154.2 6.07 153.2 6.03 43.5 1.71 20.0 0.79 CI C0810M25NY 25 154.2 6.07 153.2 6.03 42.9 1.69 19.0 0.75 NY C0810M27NY 27 166.6 6.56 165.2 6.50 42.9 1.69 19.0 0.75 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid idlers Series 810 103 Solid idler 810 is suitable for all 810, 820, 828, 831, 879B, 880B, 880J, 880LJ, 880M, 881B and 1061M series chains Standard idler has a pilot bore Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Equivalent number of teeth Ø DE Mat erial mm inch C0810L17PE 17 105.0 4.13 PE C0810L19PE 19 117.1 4.61 PE C0810L27PE 27 166.6 6.56 PE For teeth number 21, 23 and 25 use Multi-Hub 820 idler Related products Retainer rings (see page 120)

Solid sprockets Series 820 104 Solid sprocket 820 is suitable for all 810, 820 and 831 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Pilot bore size Ø PB Mat erial mm inch mm inch mm inch C0820M17NY 17 105.2 4.14 105.5 4.15 19.0 0.75 NY C0820M19NY 19 117.1 4.61 117.4 4.62 19.0 0.75 NY C0820M21CI 21 130.1 5.12 129.3 5.09 20.0 0.79 CI C0820M21NY 21 130.1 5.12 129.3 5.09 19.0 0.75 NY C0820M23CI 23 142.0 5.59 141.2 5.56 20.0 0.79 CI C0820M23NY 23 142.0 5.59 141.2 5.56 19.0 0.75 NY C0820M25CI 25 154.2 6.07 153.2 6.03 20.0 0.79 CI C0820M25NY 25 154.2 6.07 153.2 6.03 19.0 0.75 NY C0820M27NY 27 166.6 6.56 165.2 6.50 19.0 0.75 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 821 105 Solid sprocket 821 is suitable for all 800 and 821 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p L Mat erial mm inch mm inch mm inch C0821M19NY 19 117.1 4.61 117.4 4.62 79.2 3.12 NY C0821M21CI 21 130.1 5.12 129.3 5.09 80.0 3.15 CI C0821M21NY 21 130.1 5.12 129.3 5.09 79.2 3.12 NY C0821M23CI 23 142.0 5.59 141.2 5.56 80.0 3.15 CI C0821M23NY 23 142.0 5.59 141.2 5.56 79.2 3.12 NY C0821M25CI 25 154.2 6.07 153.2 6.03 80.0 3.15 CI C0821M25NY 25 154.2 6.07 153.2 6.03 79.2 3.12 NY C0821M27NY 27 166.6 6.56 165.2 6.50 79.2 3.12 NY C0821M29NY 29 179.1 7.05 177.3 6.98 79.2 3.12 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 880 106 Solid sprocket 880 is suitable for all 828, 879, 880 and 890 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Pilot bore size Ø PB Mat erial mm inch mm inch mm inch C0880M09NY 9 112.4 4.43 111.4 4.39 19.0 0.75 NY C0880M10NY 10 125.0 4.92 123.3 4.85 19.0 0.75 NY C0880M11NY 11 137.5 5.41 135.2 5.32 19.0 0.75 NY C0880M12CI 12 149.9 5.90 147.2 5.80 20.0 0.79 CI C0880M12NY 12 149.9 5.90 147.2 5.80 19.0 0.75 NY C0880M13NY 13 162.3 6.39 159.2 6.27 19.0 0.75 NY C0880M14NY 14 174.7 6.88 171.2 6.74 19.0 0.75 NY C0880M15NY 15 186.9 7.36 183.1 7.21 19.0 0.75 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 881 107 Solid sprocket 881 is suitable for all 881 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p L Pilot bore size Ø PB Mat erial mm inch mm inch mm inch mm inch C0881M19NY 19 117.1 4.61 117.4 4.62 31.8 1.25 19.0 0.75 NY C0881M21CI 21 130.1 5.12 129.3 5.09 31.0 1.22 20.0 0.79 CI C0881M21NY 21 130.1 5.12 129.3 5.09 31.8 1.25 19.0 0.75 NY C0881M23CI 23 142.0 5.59 141.2 5.56 31.0 1.22 20.0 0.79 CI C0881M23NY 23 142.0 5.59 141.2 5.56 31.8 1.25 19.0 0.75 NY C0881M25CI 25 154.2 6.07 153.2 6.03 31.0 1.22 20.0 0.79 CI C0881M25NY 25 154.2 6.07 153.2 6.03 31.8 1.25 19.0 0.75 NY C0881M27NY 27 166.6 6.56 165.2 6.50 31.8 1.25 19.0 0.75 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 882 108 Solid sprocket 882 is suitable for all 882 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C0882M09NY 9 112.4 4.43 111.4 4.39 NY C0882M10CI 10 125.0 4.92 123.3 4.85 CI C0882M10NY 10 125.0 4.92 123.3 4.85 NY C0882M11NY 11 137.5 5.41 135.2 5.32 NY C0882M12CI 12 149.9 5.90 147.2 5.80 CI C0882M12NY 12 149.9 5.90 147.2 5.80 NY C0882M13NY 13 162.3 6.39 159.2 6.27 NY C0882M14NY 14 174.7 6.88 171.2 6.74 NY C0882M15NY 15 186.9 7.36 183.1 7.21 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 1100 109 Solid sprocket 1100 is suitable for all 1100 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Diam. of pitch Ø d p Available hub type Mat erial mm inch C1100M07PE 7 59.0 2.32 A B C E PE C1100M09PE 9 74.0 2.91 A B C E PE C1100M10PE 10 82.0 3.23 A B C E PE C1100M11PE 11 90.0 3.54 A B C E PE C1100M12PE 12 98.0 3.86 A B C E PE C1100M14PE 14 114.0 4.49 A B C E PE C1100M15PE 15 122.0 4.80 A B C E PE C1100M16PE 16 130.0 5.12 A B C E PE C1100M17PE 17 138.0 5.43 A B C E PE C1100M19PE 19 154.0 6.06 A B C E PE Other materials available on request For hub type see nomenclature on page 9 Available bore sizes: Round [mm] 20, 25, 30, 35, 40 Round [inch] ¾, 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 1150 110 Solid sprocket 1150 is suitable for all 1150 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Diam. of pitch Ø d p Available hub type Mat erial mm inch C1150M07PE 7 88.0 3.46 A B C PE C1150M09PE 9 112.0 4.41 A B C E PE C1150M10PE 10 123.0 4.84 A B C E PE C1150M12PE 12 147.0 5.79 A B C E PE C1150M14PE 14 159.0 6.26 A B C E PE C1150M15PE 15 183.0 7.20 A B C E PE C1150M16PE 16 195.0 7.68 A B C E PE C1150M17PE 17 207.0 8.15 A B C E PE Other materials available on request For hub type see nomenclature on page 9 Available bore sizes: Round [mm] 20, 25, 30, 35, 40 Round [inch] ¾, 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Solid sprockets Series 1200 111 Solid sprocket 1200 is suitable for all 1200 and 3200 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Diam. of pitch Ø d p Available hub type Mat erial mm inch C1200M08PE 8 133.0 5.24 A B C E PE C1200S08PE 8 133.0 5.24 M PE C1200S08NY 8 133.0 5.24 M NY C1200M12PE 12 196.0 7.72 A B C E PE C1200S12NY 12 196.0 7.72 M NY C1200S12PE 12 196.0 7.72 M PE C1200M15NY 15 244.0 9.61 A B C E NY C1200M15PE 15 244.0 9.61 A B C E PE C1200S17NY 17 277.0 10.91 M NY C1200S17PE 17 277.0 10.91 M PE Other materials available on request Split sprockets are available For hub type see nomenclature on page 9 Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Solid sprockets Series 1250 112 Solid sprocket 1250 is suitable for all 1250 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Diam. of pitch Ø d p Available hub type Mat erial mm inch C1250M08PE 8 166.0 6.54 A B C E PE C1250M12PE 12 245.0 9.65 A B C E PE C1250M15PE 15 306.0 12.05 A B C E PE C1250M17PE 17 346.0 13.62 A B C E PE Other materials available on request For hub type see nomenclature on page 9 Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Solid sprockets Series 1400 113 Solid sprocket 1400 is suitable for all 1400 series chains Bore configurations can be machined according to the customer requirements 43.0 Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C1400M06PE 6 177.0 6.97 165.0 6.50 PE C1400M08PE 8 227.6 8.96 215.6 8.49 PE C1400M10PE 10 279.0 10.98 267.0 10.51 PE Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Solid sprockets Series 1700 114 Solid sprocket 1700 is suitable for all 1700 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C1700M08PE 8 133.0 5.24 130.6 5.14 PE C1700M10PE 10 166.1 6.54 161.8 6.37 PE C1700M12PE 12 196.0 7.72 193.2 7.61 PE C1700M13PE 13 214.0 8.43 208.9 8.22 PE Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Solid sprockets Series 3200 115 Solid sprocket 3200 is suitable for all 3200 and 1200 series chains Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Diam. of pitch Ø d p Available hub type Mat erial mm inch C3200M08NY 8 132.2 5.21 A C NY C3200M08PE 8 132.2 5.21 A C PE C3200Z08NY 8 132.2 5.21 A C NY C3200Z08PE 8 132.2 5.21 A C PE C3200M10NY 10 163.8 6.45 A C NY C3200M10PE 10 163.8 6.45 A C PE C3200M12NY 12 195.5 7.70 A C NY C3200M12PE 12 195.5 7.70 A C PE C3200S1240Q6 12 195.5 7.70 M PT C3200S1203Q6 12 195.5 7.70 M PT C3200M15NY 15 243.4 9.58 A C NY C3200M15PE 15 243.4 9.58 A C PE C3200M17NY 17 275.4 10.84 A C NY C3200M17PE 17 275.4 10.84 A C PE C3200M19NY 19 307.5 12.11 A C NY C3200M19PE 19 307.5 12.11 A C PE Standard material = Polyamide NY Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½ Split sprocket C3200Z08 - not available with square and round bore 60 mm and 2.5 inch Molded sprocket C3200S40Q6 - only available with square bore 40 mm and POM material Molded sprocket C3200S03Q6 - only available with square bore 1.5 inch and POM material For hub type see nomenclature on page 9

Solid sprockets Series 7100 116 For each 7100 series chain width one different solid sprocket 7100 is available Standard sprocket has a 25 mm bore with keyway Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p L Bore size d Bore shape mm inch mm inch mm inch mm inch C7100M16NY00R2 16 132.7 5.22 132.2 5.20 38.0 1.50 20.0 0.79 Round NY C7100M16NY25R2 16 132.7 5.22 132.2 5.20 38.0 1.50 25.0 0.98 Round NY with keyway C7100M16NY40Q2 16 132.7 5.22 132.2 5.20 38.0 1.50 40.0 1.57 Square NY C7100M12NY00R3 12 138.3 5.44 129.2 5.09 50.3 1.98 20.0 0.79 Round NY C7100M12NY25R3 12 138.3 5.44 129.2 5.09 50.3 1.98 25.0 0.98 Round NY with keyway C7100M12NY40Q3 12 138.3 5.44 129.2 5.09 50.3 1.98 40.0 1.57 Square NY C7100M12NY00R4 12 145.5 5.73 137.4 5.41 65.0 2.56 20.0 0.79 Round NY C7100M12NY25R4 12 145.5 5.73 137.4 5.41 65.0 2.56 25.0 0.98 Round NY with keyway C7100M12NY40Q4 12 145.5 5.73 137.4 5.41 65.0 2.56 40.0 1.57 Square NY Mat erial R2/Q2: for C7100K0248 chain R3/Q3: for C7100K0325 chain R4/Q4: for C7100K0405 chain

Solid idlers Series 7100 117 For each 7100 series chain width one different solid idler 7100 is available Standard idler has two 35 mm bores for bearings Sprocket data Habasit code Equivalent number of teeth Ø DE C L B Bore size d Mat erial mm inch mm inch mm inch mm inch mm inch C7100L16NY15R2 16 119.5 4.70 38.0 1.50 25.0 0.98 15.2 0.60 NY C7100L16NY35R2 16 119.5 4.70 35.0 1.38 38.0 1.50 25.0 0.98 31.0 1.22 NY C7100L12NY15R3 12 117.8 4.64 50.0 1.97 33.8 1.33 15.2 0.60 NY C7100L12NY35R3 12 117.8 4.64 35.0 1.38 50.0 1.97 33.8 1.33 31.0 1.22 NY C7100L12NY15R4 12 123.0 4.84 70.5 2.78 49.0 1.93 15.2 0.60 NY C7100L12NY35R4 12 123.0 4.84 35.0 1.38 70.5 2.78 49.0 1.93 31.0 1.22 NY R2: for C7100K0248 chain R3: for C7100K0325 chain R4: for C7100K0405 chain Other materials available on request

Solid sprockets Series NH78 118 Solid sprocket NH78 is suitable for all NH78 series chains Bore configurations can be machined according to the customer requirements 43.0 Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch CNH78M06PE 6 142.5 5.61 132.5 5.22 PE CNH78M08PE 8 183.2 7.21 173.2 6.82 PE CNH78M10PE 10 224.4 8.83 214.4 8.44 PE Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40, 50, 60 Round [inch] 1, 1 3/16, 1¼, 1½, 2, 2½ Square [mm] 25, 40, 50, 60 Square [inch] 1, 1½, 2, 2½

Split sprockets Series 1061 119 Split sprocket 1061 is suitable for 770 and 1061 series chains For teeth number 16 and 18 see Multi-Hub 1060 sprocket Bore configurations can be machined according to the customer requirements Sprocket data Habasit code Number of teeth Ø DE Diam. of pitch Ø d p Mat erial mm inch mm inch C1061Z14NY 14 116.8 4.60 113.8 4.48 NY C1061Z15NY 15 124.8 4.91 121.8 4.80 NY C1061Z17NY 17 140.8 5.54 137.8 5.43 NY C1061Z19NY 19 156.8 6.17 153.8 6.06 NY C1061Z20NY 20 164.8 6.49 161.9 6.37 NY Other materials available on request Available bore sizes: Round [mm] 25, 30, 35, 40 Round [inch] 1, 1 3/16, 1¼, 1½ Square [mm] 25, 40 Square [inch] 1, 1½

Retainer rings 120 For axial fixation of sprockets and idlers Easy installation from one side, no shaft turning for screw fixing necessary Sprocket data Habasit code A C Bore size d Bore shape Mat erial mm inch mm inch mm inch M00C0020R13+GF 44.0 1.73 14.0 0.55 20.0 Round PP with keyway M00C0025R13+GF 49.0 1.93 14.0 0.55 25.0 1.0 Round PP with keyway M00C0030R13+GF 54.0 2.13 14.0 0.55 30.0 1.19 Round PP with keyway M00C0040Q13+GF 66.0 2.60 16.0 0.63 40.0 Square PP M00C0060Q13+GF 86.0 3.39 18.0 0.71 60.0 Square PP M00C0002Q13+GF 52.0 2.05 14.0 0.55 25.4 1.0 Square PP M00C0003Q13+GF 65.0 2.56 16.0 0.63 1.5 Square PP M00C0005Q13+GF 90.0 3.54 18.0 0.71 2.5 Square PP Included in delivery: 2 retainer ring halves, 2 screws, 2 self-locking nuts Nuts and screws: stainless steel

Notes 121

Appendix Chemical resistance Plastics 122 The data presented in the following table is based on information provided by the raw material manufacturers and suppliers. It does not replace the need to test the products for your application. In individual cases, the stability of the material in the medium in question must be examined. Code: = good resistance = limited use = not recommended Materials PP PE DP LF PT TS PK EC WR WK NY HT ND G FR NG NP Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Acetic Acid > 5% Acetic Acid 5% Acetone Alcohol all types Aluminum Comp. Ammonia Ammonium Comp. Aniline Aqua Regia Arsenic Acid Barium Comp. Beer Benzene Benzenesulfonic Acid 10% Benzoic Acid Beverages (soft drinks) Borax Boric Acid Brine 10 % Butyl Acrylate Butyric Acid Carbon Dioxide Carbon Disulfide Carbon Tetrachloride Chloracetic Acid Chlorine Gas Chlorine Liquid Chlorine Water (0.4% CI) Chlorobenzene Chloroform Chromic Acid 50% Chromic Acid 3% Citric Acid 40% Citric Acid 10%

Appendix Chemical resistance Plastics 123 Code: = good resistance = limited use = not recommended Materials PP PE DP LF PT TS PK EC WR WK NY HT ND G FR NG NP Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Citrus Juices Coconut Oil Copper Comp. Corn Oil Cottonseed Oil Cresol Cyclohexane Cyclohexanol Cyclohexanone Detergents Dextrin Dibutyl Phthalate Diethyl Ether Diethylamine Diglycolic Acid 30% Diisooctyl Phthalate Dimethyl Phthalate Dimethylamine Dioctyl Phthalate Ethyl Acetate Ethyl Ether Ethylamine Ethylene Glycol 50% Ferric/Ferrous Comp. Formaldehyde 37% Formic Acid 85% Freon Fuel Oil # 2 Fruit Juices Furfural Gasoline Glucose Glycerol Heptane Hexane Hydrobromic Acid 50% Hydrochloric Acid 35% Hydrochloric Acid 10%

Appendix Chemical resistance Plastics 124 Code: = good resistance = limited use = not recommended Materials PP PE DP LF PT TS PK EC WR WK NY HT ND G FR NG NP Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Hydrofluoric Acid 35% Hydrogen Peroxide 3% Hydrogen Peroxide 90% Hydrogen Sulfide Igepal 50% Iodine Crystals Isooctane Isopropyl Alcohol Jet Fuel Kerosene Lactic Acid Lanolin Lauric Acid Lead Acetate Linseed Oil Lubricating Oil Magnesium Comp. Malic Acid 50% Manganese Sulfate Margarine Mercury Methyl Chloride Methyl Ethyl Ketone Methyl Isobut. Ketone Methyl Isobut. Ketone Methylsulfuric Acid Methylene Chloride Milk Mineral Oil Mineral Spirits Molasses Motor Oil Naphtha Nitric Acid 30% Nitric Acid 50% Nitrobenzene Nitrous Acid Nitrous Oxide

Appendix Chemical resistance Plastics 125 Code: = good resistance = limited use = not recommended Materials PP PE DP LF PT TS PK EC WR WK NY HT ND G FR NG NP Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Oleic Acid Olive Oil Oxalic Acid Ozone Palmitic Acid 70% Paraffin Peanut Oil Perchloric Acid 20% Perchlorothylene Pathalic Acid 50% Phenol Phenol 5 % Phosphoric Acid 30% Phosphoric Acid 85% Photographic Solutions Plating Solutions Potassium Comp. Potassium Hydroxide Potassium Iodide (3% Iodine) Potassium Permanganate Silver Cyanide Silver Nitrate Sodium Comp. Sodium Chlorite Sodium Hydroxide 60% Sodium Hypochlorite 5% Stearic Acid Sulfamic Acid 20% Sulfate Liquors Sulfur Sulfur Chloride Sulfur Dioxide Sulfuric Acid 10% Sulfuric Acid 50% Sulfuric Acid 70% Sulfurous Acid Tannic Acid 10% Tartaric Acid

Appendix Chemical resistance Plastics 126 Code: = good resistance = limited use = not recommended Materials PP PE DP LF PT TS PK EC WR WK NY HT ND G FR NG NP Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Tetrahydrofuran Toluene Transformer Oil Tributyl Phosphate Trichloroacetic Acid Trichloroethylene Tricresyl Phosphate Trisodium Phosphate Turpentine Urea Vinegar Wine Xylene The data in this table is taken from laboratory tests, performed on unstrained test samples. It should be considered as purely indicative, since material behavior under real working conditions depends on different factors, including: temperature, concentration of the chemical agent, and speed or long-lasting effect of the chemical agent. With thermoplastic products, do not use cleaning or lubricating agents with ph values below 4 or above 10.

Appendix Chemical resistance Steel 127 Code: = good resistance = limited use = not recommended Materials SS SH SA IN Materials SS SH SA IN Chemical Acetic Acid > 5% Acetic Acid 5% Acetone Alcohol all types Aluminum Comp. Ammonia Aniline Aqua Regia Beer Benzene Benzoic Acid Beverages (soft drinks) Borax Boric Acid Brine 10% Butter Carbon Dioxide Carbon Disulfide Carbon Tetrachloride Chlorine Gas Chlorine Liquid Chloroform Citric Acid 40% Citric Acid 10% Distilled water Ethyl Ether Ferric/Ferrous Comp. Formaldehyde 37% Formic Acid 85% Fruit Juices Gasoline Glucose Glycerol Hydrobromic Acid 50% Hydrochloric Acid 35% Hydrochloric Acid 10% Hydrofluoric Acid 35% Hydrogen Peroxide 3% Hydrogen Peroxide 90% Hydrogen Sulfide Iodine Crystals Kerosene Lactic Acid Lead Acetate 20 C (70 F) 60 C (140 F) 20 C (70 F) 60 C (140 F) Chemical 20 C (70 F) 60 C (140 F) 20 C (70 F) Linseed Oil Magnesium Comp. Malic Acid 50% Margarine Mercury Methyl Ethyl Ketone Methylene Chloride Milk Mineral Oil Motor Oil Nitric Acid 25% Nitric Acid 50% Oleic Acid Olive Oil Oxalic Acid Ozone Palmitic Acid 70% Phenol Phosphoric Acid 25% Phosphoric Acid 50% Photographic Solutions Potassium Hydroxide Siver Nitrate Soap and water Sodium Chlorite Sodium Hydroxide Sodium Hydroxide 60% Sodium Hypo-chlorite (5% CI) Sulfur Sulfur Dioxide (dry) Sulfur Dioxide (wet) Sulfuric Acid 10% Sulfuric Acid 50% Sulfuric Acid 70% Tannic Acid 10% Tartaric Acid Toluene Transformer Oil Turpentine Urea Vinegar Whisky Wine Xylene 60 C (140 F)

Appendix Safety information 128 When connecting or disconnecting a chain, always turn off and lock out the power switch before starting. Always use goggles to protect your eyes. Wear protective clothing, gloves and safety shoes. Support the chain to prevent uncontrolled movements. Use appropriate tools in good working condition, and use the correctly in a proper manner. Do not attempt to connect or disconnect the chain without full knowledge of the chain construction, including the correct procedure for pin removal or insertion. All pinch and shear points, along with all other exposed moving parts that pose a potential hazard to people at workstations or on conveyor passageways, must be safeguarded. Overhead conveyors must have guards to prevent objects from falling. Cleated conveyor chains are more hazardous, creating pinch and shear points. Safeguarding can be achieved by: Identification Identify all hazardous areas that pose a danger to personnel. Guard barriers Place guard barriers to prevent entry into the hazardous area, and apply guards to high conveyors to prevent objects from falling on to personnel below. Control devices Set machine controls to prevent hazardous operations/ conditions. Warnings Use instructions, warning labels, or sound/light signals to alert that a hazardous condition exists. Safeguarding should be designed to minimize any discomfort or difficulties for operators. Bypassing and/or overriding safeguarding mechanisms during operation should not be allowed. Any safeguarding concerns regarding the conveyor should be addressed during the design process. Product safety Products designed and manufactured by Habasit can be used in a safe manner; but Habasit cannot warrant their safety under all circumstances. PURCHASER MUST INSTALL AND USE THE PRODUCTS IN A SAFE AND LAWFUL MANNER IN COMPLIANCE WITH APPLICABLE HEALTH AND SAFETY REGULATIONS AND LAWS AND GENERAL STANDARDS OF REASONABLE CARE; AND IF PURCHASER FAILS TO DO SO, PURCHASER SHALL INDEMNIFY HABASIT FROM ANY LOSS, COST OR EXPENSE RESULTING DIRECTLY OR INDIRECTLY FROM SUCH FAILURE. SAFETY DEVICES: Products are provided with only the safety devices identified herein. IT IS THE RESPONSIBILITY OF PURCHASER TO FURNISH APPROPRIATE GUARDS FOR MACHINERY PARTS IN COMPLIANCE WITH MSHA OR OSHA STANDARDS, AS WELL AS ANY OTHER SAFETY DEVICES DESIRED BY PURCHASER AND/OR REQUIRED BY LAW; AND IF PURCHASER FAILS TO DO SO, PURCHASER SHALL INDEMNIFY HABASIT FROM ANY LOSS, COST OR EXPENSE RESULTING DIRECTLY OR INDIRECTLY FROM SUCH FAILURE. General safety precautions To avoid personal injury, all machinery must be turned off and locked out, prior to chain installation, inspection, maintenance and removal Always use safety glasses to protect eyes. Wear protective clothing, gloves and safety shoes Support the chain to prevent uncontrolled movement of the chain and parts Maintain tools in proper condition and ensure their proper use. Use of chain assembly tools is recommended when applicable Do not attempt to connect or disconnect chain unless chain construction is clearly known and understood Do not use any sections of damaged chains, because they may have been overloaded and yielded If any flame cutting, welding, etc. is done in the conveyor vicinity, take adequate precautions to ensure that no burning of any chain or other components occurs. If adequate protection cannot be provided, remove the chain and other plastic components from the conveyor and store in a safe location. Thermoplastic and similar materials can burn and give off toxic fumes. DO NOT IN STALL, OPERATE OR PERFORM MAINTENANCE ON THIS PRODUCT UNTIL YOU HAVE READ AND UNDER STOOD THE INSTRUCTIONS CONTAINED IN THIS MANUAL.

Notes 129

The Habasit solution Customers first At Habasit we understand that our success depends on your success. This is why we offer solutions, not just products; partnership, not just sales. Since our foundation in 1946, Habasit has brought this understanding of customer needs to life every day and for every application. That s why we re the No. 1 in belting today. Worldwide. Learn more at www.habasit.com Committed to innovation Because our customers' belting challenges and needs never cease, we consistently dedicate a substantial percentage of our employees and resources to the research and development of new products and solutions. Certified for quality We deliver the highest quality standards not only in our products and solutions, but also in our employees daily work processes. Habasit AG is certified according to ISO 9001:2008. Worldwide leading product range Habasit offers the largest selection of belting, conveying, processing and complementary products in the industry. Our response to any request is always a specific, tailor-made solution. Fabric-based conveyor and processing belts HabaFLOW Plastic modular belts HabasitLINK Positive drive conveyor and processing belts Habasit Cleandrive TM Power transmission belts HabaDRIVE Timing belts HabaSYNC Chains (slat and conveyor chains) HabaCHAIN Machine tapes Round belts Seamless belts Profiles, Guides, Wear strips HabiPLAST Fabrication tools (joining tools) Gearmotors Electric motors Motion control

Austria Habasit GmbH Wien Phone: +43 1 690 66 www.habasit.at India Habasit-Iakoka Pvt. Ltd. Coimbatore Phone: +91 422 262 78 79 www.habasitiakoka.com Russia OOO Habasit Ltd. St. Petersburg Phone: +7 812 600 40 80 www.habasit.ru Ukraine Habasit Ukraine LLC. Vinnytsa Phone: +38 0432 58 47 35 www.habasit.ua Belgium Habasit Belgium N.V. Zaventem Phone: +32 27 250 430 www.habasit.be Canada Habasit Canada Ltd. Oakville Phone: +1 905 827 41 31 www.habasit.ca China Habasit East Asia Ltd. Hong Kong Phone: +85 221 450 150 www.habasit.com.hk Habasit (Shanghai) Co. Ltd. Shanghai Phone: +8621 5488 1228 Phone: +8621 5488 1218 www.habasit.com.hk France Habasit France S.A.S. Mulhouse Phone: +33 389 338 903 www.habasit.fr Germany Habasit GmbH Eppertshausen Phone: +49 6071 969 0 www.habasit.de Italy Habasit Italiana SpA Customer Care: Phone: 199 199 333 For int. calls: +39 0438 911 444 www.habasit.it Japan Habasit Nippon Co. Ltd. Yokohama Phone: +81 45 476 0371 www.habasit.co.jp Netherlands Habasit Netherlands BV Nijkerk Phone: +31 332 472 030 www.habasit.nl New Zealand Habasit Australasia Ltd. Hornby Phone: +64 3348 5600 www.habasit.co.nz Norway Habasit Norge A/S, Oslo Phone: +47 815 58 458 www.habasit.no Poland Habasit Polska Sp. zo.o. Dąbrowa Górnicza Phone: +48 32639 02 40 www.habasit.pl Singapore Habasit Far East Pte. Ltd. Singapore Phone: +65 686 255 66 www.habasit.com.sg Spain Habasit Hispanica S.A. Barberà del Vallès Phone: +34 937 191 912 www.habasit.es Sweden Habasit AB Hindas Phone: +46 30 122 600 www.habasit.se Switzerland Habasit GmbH Reinach Phone: +41 61 577 51 00 www.habasit.ch Taiwan Habasit Rossi (Taiwan) Ltd. Taipei Hsien Phone: +886 2 2267 0538 www.habasit.com.tw Turkey Habasit Kayis San. Ve Tic. Ltd. Sti. Yenibosna-Bahcelievler-Istanbul Phone: +90 212 654 94 04 www.habasit.com.tr United Kingdom and Ireland Habasit (UK) Ltd. Silsden Phone: +44 844 835 9555 www.habasit.co.uk USA Habasit America Conveyor belts, power transmission belts, gearmotors Suwanee, Georgia Phone: +1 800 458 6431 www.habasitamerica.com Habasit America Seamless belts, timing belts Middletown, Connecticut Phone: +1 860 632 2211 www.habasitamerica.com Rossi is one of Europe s largest manufacturers of gear reducers, gearmotors, inverters, standard and brakemotors, and is a member of the Habasit Group. Rossi S.p.A. Via Emilia Ovest 915/A 41123 Modena Italy Phone: +39 059 33 02 88 www.rossi-group.com info@rossi-group.com Headquarters Habasit AG CH-4153 Reinach-Basel Phone +41 61 715 15 15 Fax +41 61 715 15 55 E-mail info@habasit.com www.habasit.com Copyright Habasit AG Subject to alterations Printed in Switzerland Publication data: