STC-MBA5MUSB3 STC-MCA5MUSB3 USB 3.0 Camera

STC-MBA5MUSB3 STC-MCA5MUSB3 USB 3.0 Camera

CAUTION CAUTION CAUTION! RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK RISK DO OF NOT ELECTRIC OPEN DO NOT SHOCK OPEN DO NOT OPEN CAUTION: CAUTION: CAUTION: TO REDUCE TO THE REDUCE RISK OF THE ELECTRIC RISK OF SHOCK, ELECTRIC DO SHOCK, NOT DO NOT REMOVE TO REDUCE COVER REMOVE THE (OR RISK COVER BACK). OF ELECTRIC (OR NO BACK). USER SHOCK, SERVICEABLE NO USER DO NOT SERVICEABLE PARTS REMOVE INSIDE. COVER PARTS INSIDE. (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING REFER SERVICING TO QUALIFIED TO QUALIFIED SERVICE PERSONNEL. SERVICE PERSONNEL. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. STC-MBA5MUSB3/MCA5MUSB3 Safety Precautions! For U.S.A. For U.S.A. Warning: For U.S.A. Warning: Warning: This equipment This equipment generates and generates uses radio and uses frequency radio frequency energy and energy if and if not This installed equipment generates and uses radio frequency energy and if not and installed used properly, and used I.e., properly, in strict I.e., accordance in strict accordance with the with the instruction not installed and used properly, I.e., in strict accordance with the instruction manual, may manual, cause may harmful cause interference harmful interference to radio to radio communications. instruction manual, may cause harmful interference to radio communications. It has been It tested has been and tested found and to comply found to with comply the with the limits communications. for a Class A It computing has been tested device and pursuant found to to Subpart comply J with of Part the limits for a Class A computing device pursuant to Subpart J of Part 15 limits of FCC for Rules, a Class which A computing are designed device to pursuant provide reasonable to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection 15 of FCC against Rules, such which interference are designed when to provide operated reasonable protection against such interference when in operated a commercial in a commercial environment. protection against such interference when operated in a commercial environment. environment. The lightning The flash lightning with flash arrowhead with arrowhead The lightning flash with arrowhead symbol, within symbol, an equilateral within an equilateral triangle, triangle, symbol, within an equilateral triangle, is is intended is intended to intended to alert alert the to the user alert user to the to theuser to the the presence presence of presence of uninsulated of uninsulated uninsulated dangerous dangerous dangerous voltage voltage within voltage within the within the product s the product s product s enclosure enclosure that that may may be that be of may of sufficient be of sufficient magnitude magnitude to to constitute to constitute a a risk risk of a risk of of electric shock electric to to persons. shock to persons. For Canada For Canada For Canada Warning: Warning: Warning: This This digital This digital apparatus digital apparatus apparatus does does not not exceed does not exceed the exceed the Class Class A the A limits Class limits for A for radio limits for radio radio noise noise emissions noise emissions emissions from from digital from digital apparatus digital apparatus apparatus set set out out in in the set the Radio out in the Radio Radio Interference Interference Interference Regulations Regulations Regulations of of the the Canadian of the Canadian Department Canadian Department Department of of of Communications. Communications.!!! The exclamation point within an The exclamation point within an an equilateral triangle is intended to alert equilateral is to the triangle user to is the intended presence to alert of important the the user to to the the presence of of important operating and maintenance (servicing) operating and and maintenance (servicing) instructions the literature instructions in the the literature accompanying the appliance. accompanying the the appliance. WARNING: WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE TO TO PREVENT FIRE OR OR SHOCK HAZARD, DO DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THIS APPLIANCE TO TO RAIN OR OR MOISTURE. Product Precautions Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or storage could damage the camera. Do not pull or damage the camera cable. During camera use, do not wrap he unit in any material. This will cause the internal temperature of the unit to increase. Do not expose the camera to moisture, or do not try to operate it in wet areas. Do not operate the camera beyond its temperature, humidity and power source ratings. While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or contamination from getting in the CCD or filter area and scratching or damaging this area. Do not keep the camera under the following conditions: In wet, moist, and high humidity areas Under hot direct sunlight In high temperature areas Near an object that releases a strong magnetic or electric field Areas with strong vibrations Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not scratch the surface of the glass. Product Specifications 2 Ver 1.00

Copyright & Disclaimer Sensor Technologies America, Inc. (DBA Sentech America) believes the contents and specifications of its website, catalog, documentation and ads are correct; however, Sentech America provides no representation or warranty regarding such information or product(s) contained therein. It is requested that Sentech America be given appropriate acknowledgement in any subsequent use of such work by a third party. While every effort has been made to ensure that the details contained in Sentech America s website and all documentation are correct and up-to-date, Sentech America assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers, process, software or model applications. Sentech America reserves the right to change specifications, product descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these products. By installing and/or using a Sentech America software development kit or other similar product and/or information obtained from Sentech America s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions. Product Specifications 3 Ver 1.00

Table of Contents I. Notes on PCs with Power Save Mode... 5 A. Cause of the Issue... 5 B. Solutions for the Issue... 5 II. General Specifications... 6-9 A. Electronic Specifications... 6 B. Spectral Response Characteristics... 7-8 C. Mechanical Specifications... 9 D. Environmental Specifications... 9 III. Interface Connector Specifications... 10 A. USB Connector... 10 B. I/O Connector... 10 IV. Input / Output Specifications... 11-17 A. Input Signals... 11-12 B. Output Signals... 13-17 V. Dimensions... 18 Product Specifications 4 Ver 1.00

I. Notes on PCs with Power Save Mode When the USB camera is used with a PC that has the power save mode, such as a PC with the Intel Core i3, i5, or i7 CPU, the following problem may occur. An image cannot be obtained with the USB camera A frame drops frequently * The issue may occur with other USB camera manufacturers as well. A. Cause of the Issue The PC becomes unable to transfer the image because the CPC frequently enters the power save mode during the image transfer. B. Solutions for the Issue This problem can be avoided by disabling the power save mode. However, depending on the PC, the power save mode cannot be disabled and the desired effect may not be achieved. In addition, when the power save mode is disabled, undesired effects such as an increase of the power consumption and the heat of the PC may occur. 1. Disable the power save mode by changing the BIOS settings. Either set ACPI C State to Disable or decrease the Max ACPI C State value step by step until you see the effect (i.e. C3->C2->C1). (The setting method and the naming may differ, and/or these settings cannot be changed depending on the PC.) Please contact the manufacturer of the PC about the BIOS setting. ACPI C State and Max ACPI C State may have different names depending on the PC. Users will be responsible for any change made to the BIOS setting. The power consumption and the heat of the PC will increase whenever the power save mode is disabled. Please understand and accept this before disabling the power save mode. 2. Disable the power save mode with the Sentech PC power management software (StPowerCtrl) Please refer to the Start-Up Guide for the details. 3. Change the camera blanking period and reduce frame rate. Product Specifications 5 Ver 1.00

II. General Specifications A. Electronic Specifications Model Number STC-MBA5MUSB3 STC-MCA5MUSB3 Image Sensor Active Picture Elements 1/2.5 5M pixel Monochrome CMOS (Aptina:MT9P031I12STM) 2592(H) x 1944(V) Cell Size 2.2 (H) x 2.2 (V) µm Scanning System Progressive Shutter Type Rolling Shutter Scanning Mode Maximum Frame Rate (in Full Scanning Mode) Maximum Frame Rate (in Full Binning Scanning and AOI Mode) Sync. System Video Output Format 1/2.5 5M pixel Color CMOS (Aptina:MT9P031I12STC) Full Scanning, Variable AOI (Horizontal / Vertical) QSXGA: 2592 x 1944 : 14fps (Settable from 6.88 to 14fps) *Frame rate will drop if connected with the USB2.0 port. (Raw 8bit output: 7fps Raw 10/12bit output 3.5fps) Vertical 1/2 Binning: 28fps, Vertical 1/4 Binning: 34.6fps (in full scanning mode) QXGA (2048 x 1536) : 21fps, UXGA (1600 x 1200) : 31fps, SXGA (1280 x 1024) : 42fps, XGA (1024 x 768) : 63fps, SVGA (800 x 600) : 91fps, VGA (640 x 480) : 126fps, Minimum AOI (32 x 32): 2106fps RAW8bit/10bit/12bit Internal BGR8bit, RAW8bit/10bit/12bit, Mono8bit/10bit/12bit S/N Ratio (8bit) 4 Digit (Gain 0 db) 4 Digit (Gain 0 db) Minimum Scene Illumination 0.3 Lux at F1.2 9 Lux at F1.2 ALC Electronic Shutter Gain Digital Clamp Gamma AOI Analog Digital Auto Shutter / Auto Gain Free-run Mode: Exposure Time -- 32 µsec to 38sec (in full scanning mode) Edge Preset Trigger Mode: Exposure Time -- 32 µsec to 38sec (in full scanning mode) Pulse-width Trigger Mode: Exposure Time -- 32 µsec to unlimited (in full scanning mode) 0 to 26.97 db 0 to 12.04 db 0 to 255 (LSB of 12bit output) 0.1 to 4.0 (settable with 0.1 step) AOI (Horizontal: 32 to 2592 pixels / Vertical: 32 to 1944 lines) Adjustable Steps: 4 pixels in horizontal direction and 4 lines in vertical direction Binning Function Horizontal 1/2, 1/4 Vertical 1/2, 1/4 *Only pixels in the horizontal direction can be added to increase the brightness. Skipping Function Horizontal 1/2, 1/3, 1/4, 1/5, 1/6, 1/7 Vertical 1/2, 1/3, 1/4, 1/5, 1/6, 1/7, 1/8 Mirror Image Pixel Defect Correction Horizontal / Vertical / Horizontal and Vertical Up to 64 pixels (This function is turned off at shipping.) White Balance N/A Auto / Manual/ One-shot Operational Mode Free-run / Edge-preset Trigger/ Pulse-width Trigger / Start and Stop Trigger Frame Memory 32 MB Interface USB3.0 Super speed (USB3.0 Micro B) Input/Output Input Voltage Power Consumption Two Inputs and Two Outputs +5V(typ.) (Conform to USB Standard) Less than 2W Product Specifications 6 Ver 1.00

B. Spectral Sensitivity Characteristics 1. STC-MBA5MUSB3 2. STC-MCA5MUSB3 Product Specifications 7 Ver 1.00

3. NF-50D (IR Cut Filter) Product Specifications 8 Ver 1.00

C. Mechanical Specifications Model Number STC-MBA5MUSB3 STC-MCA5MUSB3 Dimensions 28 (W) x 28 (H) x 33.8 (D) mm *excluding the connector Lens Mount CS Mount Optical Filter No IR Cut Filter IR Cut Filter Optical Center Accuracy Positional accuracy in H and V directions: +/- 0.5 mm Rotational accuracy of H and V: +/- 0.35 deg. Weight Approximately 38 g Interface Connectors USB Connector: USB3.0 MicroB type I/O Connector: HR10A-7R-6PB (Hirose) or equivalent D. Environmental Specifications Model Number STC-MBA5MUSB3 / STC-MCA5MUSB3 Operational Temperature 0 ~ +40 Storage Temperature -30 ~+65 Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each Shock Acceleration 38G, half amplitude 6ms, 3 directions 3 times each Standard Compliancy EMS: EN61000-6-2, EMI: EN55011 RoHS RoHS Compliant Product Specifications 9 Ver 1.00

III. Interface Connector Specifications I/O Connector USB Connector A. USB Connector USB 3.0 Micro-B Type B. I/O Connector HR10A-7R-6PB (Hirose) or equivalent This connector is for input triggers and output signals. Use HR10A-7P-6S (Hirose) or equivalent for the cable side. The power input of this connector is for output signals, not for the power supply of the camera. The camera power is provided from the USB connector via USB bus which carries +5V. This +5V does not affect the voltage of output signals. Pin Assignment Pin No. Signal Name IN / OUT Low Voltage 1 GND (IO_GND) - 0V 2 Output 2 (IO3) OUT 3 Output 1 (IO2) OUT 4 Input 2 (IO1) IN 5 Input 1 (IO0) IN 6 Power Input (IO_VCC) Smaller than 0.8 V Smaller than 0.8 V Smaller than 0.7 V Smaller than 0.7 V - +3 to +26.4Vdc High +3 to +26.4 V +3 to +26.4 V +1.7 to +5 V +1.7 to +5 V [Back Side] Product Specifications 10 Ver 1.00

IV. Input / Output Signal Specifications A. Input Signals 1. Input Signal Functions Using the software, the following functions can be set on Input 1 and Input 2 of the I/O connector. The polarity of Trigger Input and Sub-Trigger Input is selectable. Function No. Function Name Polarity 1) Disabled (Default) - 2) General Input - 3) Trigger Input Positive or Negative 4) Sub-trigger Input Positive or Negative 1) Disabled Set when no input signal is necessary. 2) General Input Set high of low level and the user can check the status on the software. 3) Trigger Input Use this function for the trigger signal in the edge preset mode and for the start trigger in the start and stop trigger mode. 4) Sub-trigger Input Use this function for the stop trigger in the start and stop trigger mode. 2. Input Signals Electronic Characteristics Input Signal / Input Voltage: 0 to 5V Input Signal / Voltage Level High Level: 1.7V (min.) Low Level: 0.7V (max.) Product Specifications 11 Ver 1.00

3. Input Signal Circuit 4. Input Signal Circuit Examples CAMERA internal power is applied MAX_5V INPUT SN74LVC2G241YZPR (T I) 100 ohm USER INPUT 10k ohm IO_GND 1 2 CUS03 (Tos hiba) GND IO_GND CAMERA MAX_5V internal power is applied INPUT SN74LVC2G241YZPR (T I) 10k ohm 100 ohm Tr USER INPUT 1 2 CUS03 (Tos hiba) IO_GND GND *The voltage applied on input 1 and input 2 must be less than or equal to 5V, the absolute maximum input voltage. IO_GND Product Specifications 12 Ver 1.00

B. Output Signals 1. Output Signal Functions Using the software, the following functions can be set on Output 1 and Output 2 of the I/O connector. The polarity of Trigger Output Programmable, Trigger Output Loop Through, Exposure End, CCD Read End Output, Strobe Output Programmable, Strobe Output Exposure and Trigger Valid Out is selectable. Negative Polarity is recommended to use to reduce the timing delay due to open drain output. Function No. Function Name Polarity 1) Disabled (Default) - 2) General Output - 3) Trigger Output Programmable Positive or Negative 4) Trigger Output Loop Through Positive or Negative 5) Exposure End Positive or Negative 6) Read End Output Positive or Negative 7) Strobe Output Programmable Positive or Negative 8) Strobe Output Exposure Positive or Negative 9) Trigger Valid Out Positive or Negative 1). Disabled Set when no output signal is necessary. 2). General Output Outputs high or low level signal set on the software. 3). Trigger Output Programmable Outputs the trigger input signal with delay setting applied. 4). Trigger Output Loop Through Outputs the trigger input sign (with a slight internal delay). 5). Exposure End Output a signal upon the completion of the first line exposure. ( Trigger Out Delay and Trigger Pulse Width settings are applied.) 6). Read End Output Output a signal upon the completion of the transfer of a full frame. ( Trigger Out Delay and Trigger Pulse Width settings are applied.) 7). Strobe Output Programmable Output a signal for the period set with strobe end delay, starting at the trigger input signal with the addition of strobe start delay 8). Strobe Output Output a signal during the first lien of exposure*. Product Specifications 13 Ver 1.00

9). Trigger Valid Out With the positive polarity setting, high status indicates that the input trigger signal is acceptable. This signal becomes low from the exposure start to the end of image output. With the negative polarity setting, low status indicates that the input trigger signal is acceptable. This signal becomes high from the exposure start to the end of image output. * Because this camera is a rolling shutter type, the exposure start timing of each line is not simultaneous. Product Specifications 14 Ver 1.00

2. Output Signal Electronic Characteristics Output Signal / Voltage Level High Level: Power Input of the I/O Connector (+3 ~ + 26.4 V) Low Level: Smaller than 0.8 V Output Signal / Pulse Width Pulse width is settable using the software. Please refer to the response timing chart below and set with a sufficient margin. Output Signal / Response Timing The response timing shown below is a reference value measured without an eternal resistance. Ts Td 3.3V INTERNAL SIGNAL 0V 90% IO_VCC USER OUTPUT Tf Tr 10% IO_GND IO_VCC 3.3[V] 5.0[V] 12[V] 24[V] Td 2.00 [us] 1.82 [us] 1.66 [us] 1.60 [us] Tr 0.82 [us] 0.84 [us] 1.16 [us] 1.44 [us] Ts 0.50 [us] 0.56 [us] 0.56 [us] 0.70 [us] Tf 0.56 [us] 0.66 [us] 1.16 [us] 2.04 [us] Product Specifications 15 Ver 1.00

3. Output Signal Circuit 4. Output Signal Circuit Examples CAMERA IO_VCC 22k ohm OUT PUT 100 ohm DTC144EM (Rohm) USER OUT PUT 1 2 GND CUS03 (Tos hiba) IO_GND *The voltage applied on the IO_VCC must be within the range of +3V to 26.4V. Product Specifications 16 Ver 1.00

USER_VCC CAMERA N.C USER OUT PUT IO_VCC 22k ohm OUT PUT 100 ohm DTC144EM (Rohm) USER_Ic 1 2 GND CUS03 (Tos hiba) IO_GND USER_GND * When no voltage is applied on IO_VCC, it can be used as an open collector output. * The voltage applied on IO2 and IO3 (USER_VCC) must be less than or equal to 26.4V. * The incoming current to IO2 and IO3 (USER_lc) must be less than or equal to 15mA. Product Specifications 17 Ver 1.00

V. Dimensions Unit: mm *How to Identify Monochrome and Color Camera. STC-MBA5MUSB3 STC-MCA5MUSB3 Product Specifications 18 Ver 1.00

Revisions Rev Date Changes Note.01 April, 5 2012 New document.02 April 12, 2012 Corrected Maximum Frame Rate for VGA.03 April 20, 2012 Added Interface Connector Specifications 1.00 October 25, 2012 Full Release Document Sensor Technologies America, Inc. 1345 Valwood Pkwy, Suite 320 Carrollton, Texas 75006-6891 TEL (972) 481-9223 FAX (972) 481-9209 URL http://www.sentechamerica.com/ Sensor Technology Co., Ltd. 7F, Harada Center Building 9-17, Naka cho 4chrome Atsugi-city, Kanagawa 243-0018 Japan TEL +81-46-295-7061 FAX +81-46-295-7066 URL http://www.sentech.co.jp/ Taiwan Sensor Technology, Inc. 3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng District Taipei City 100, Taiwan, R.O.C. TEL 886-2-2383-2331 FAX 886-2-2370-8775 EMAIL: sentech0501@yahoo.com.tw Product Specifications 19 Ver 1.00