Aquila AT01 NORMAL & EMERGENCY CHECKLIST

Similar documents
King Air C90A. Speeds (KIAS)

CESSNA 172 CHECKLIST TAXI PRE-EXTERNAL CHECKS. 1. Lights - As required 2. Brakes - CHECK 3. Rolling Instruments Check - L/R

Super King Air 200. Speeds (KIAS)

File Number MDRA C20 MANUAL of PROCEDURES for INSPECTION of COMPOSITE AMATEUR-BUILT AIRCRAFT, INSPECTION AND TECHNICAL INFORMATION RECORD

Multi Engine Oral Exam Questions

Lancair Legacy Annual Condition Inspection Checklist

FLYBLOCKTIME PA /160 Aircraft Type Checkout and Currency Quiz. NOTE: There may be one or more correct answers to each question.

VFR Day Emergencies - C172R

SINGLE ENGINE TURBO-PROP AEROPLANE ENDORSEMENT

CIRRUS AIRPLANE MAINTENANCE MANUAL

MULTI-ENGINE TURBO-PROP AEROPLANE ENDORSEMENT

MULTI-ENGINE PISTON AEROPLANE ENDORSEMENT

SINGLE ENGINE PISTON AEROPLANE ENDORSEMENT

FLY SYNTHESIS STORCH HS-CL

CUB CRAFTERS, INC. CC PILOT S OPERATING HANDBOOK AND FLIGHT TRAINING SUPPLEMENT

MULTI-ENGINE TURBO-PROP AEROLANE ENDORSEMENT

LANDING GEAR & BRAKES GTM CONTENTS INTRODUCTION

MULTI-ENGINE PISTON AEROPLANE ENDORSEMENT ENGINEERING, DATA AND PERFORMANCE QUESTIONNAIRE

Cessna Grand Caravan Pilot s Technical Examination

2013 Airborne Aviation Pty Ltd

BOMBARDIER CRJ700. Bombardier CRJ700 Aircraft Reference

FLIGHT TRAINING (AEROPLANE) BASED ON JAR FCL - PPL(A) FLIGHT INSTRUCTION Syllabus

General Characteristics

AIRCRAFT GENERAL GTM CONTENTS

Aviation Supplies & Academics, Inc nd Place SE Newcastle, Washington

This is the fourth of a series of Atlantic Sun Airways CAT B pilot procedures and checklists for our fleet. Use them with good judgment.

DA Katana 4X Manual. This Chapter provides description and operation of the airplane and its systems.

ELECTRICAL. Primary electrical power is provided by two engine driven generators which supply three-phase, 115 volt 400 cycle alternating current.

Cherokee Archer II Pilot s Operating Handbook

This is the third of a series of Atlantic Sun Airways CAT B pilot procedures and checklists for our fleet. Use them with good judgment.

FLIGHT CONTROLS 1. GENERAL 2. MAIN COMPONENTS AND SUBSYSTEMS ROLL CONTROL. Smartcockpit.com BOEING 737 SYSTEMS REVIEW Page 1

INSPECTION BEFORE RIDING

FLIGHT REFERENCE CARDS

TOYOTA ELECTRONIC TRANSMISSION CHECKS & DIAGNOSIS

S-Tec System Thirty Autopilot

CDS TROUBLESHOOTING SECTION I. VACUUM Weak vacuum at wand. Gauge reads normal (10hg to 14hg)

Oral Preparation Questions

B777. Landing Gear DO NOT USE FOR FLIGHT

MODULE 11B. PISTON AEROPLANE AERODYNAMICS, STRUCTURES AND SYSTEMS

Model No. BC460-H Alternator. B & C Specialty Products P.O. Box B Newton, KS (316)

Revision Number Revision Date Insertion Date/Initials 1 st Ed. Feb 01, 00 2 nd Ed. Jun 24, 02 3rd Ed. Feb 15, 07

Pilot operating handbook. And. Flight operating supplement. AEROPRO + EuroFOX Aviation. EuroFOX

SD3-60 AIRCRAFT MAINTENANCE MANUAL AND MOORING - GENERAL

ACCUMULATOR INSTALLATION

AutoGlow Installation and User s Manual. Installation and User s Manual. OSA AutoGlow. Figure 1. AutoGlow Introduction

Light Sport West Standard Flight Training Procedures for N110GX (Remos GX, 100 H.P.)

Multi-information Display (see MID )

Compiled by Matt Zagoren

This section includes performance data on the King Air B200. Information consists of:

OPERATING LIMITATIONS

Multi-Engine Training And The PTS

Nomad WINGS FLAP OPERATING LIMITATIONS

Brief introduction

Cessna 172SP & NAV III Maneuvers Checklist

The SeaRey - An Introduction

Flight Manual. FM 250 Vampire. Flight Manual

Automation at Odds. A 737 stalled when a radio altimeter malfunction caused the autothrottle and autopilot to diverge during an approach to Schiphol.

Electro-Mechanical Landing Gear System. Landing Gear and Brakes

Cessna Citation 500/501 Pilot s Technical Examination

A.Y. McDonald Mfg. Co. Troubleshooting Submersible and Jet Pumps

CENTRE EST AERONAUTIQUE

ENGINE FIRE / SEVERE DAMAGE / SEPARATION ON TAKEOFF

RC HELICOPTER INSTRUCTION MANUAL

Draining and filling cooling system

MCR-01 Ultralight. AFS-design. Andreas Meyer

CHAPTER 11 MARKING AND PLACARDS

McCAULEY CONSTANT SPEED PROPELLER GOVERNING SYSTEM

Oil and Coolant Circulating Heating System. Model - OCSM

DA20-A1/DA List of Applicable Publications

Diesel Engine Driven Generators Page 1 of 6

VEHICLE SPEED CONTROL SYSTEM

Assessment Specifications for Remotely Piloted Aircraft Systems, Class 1 AS-RPAS1

REMOVAL AND INSTALLATION

PILOT OPERATING HANDBOOK FOR ROCKWELL TURBO COMMANDER 690B

Cooling system components, removing and installing

McCAULEY FULL FEATHERING CONSTANT SPEED PROPELLER GOVERNING SYSTEM. Professor Von Kliptip Answers Your Questions About The

Assembly and Operating Manual Nano warbirds FW 190 Specification: *Length: 18 1/2"(470mm) *Wing Span: 21 7/10"(550mm)

Cooling system components, removing and installing

ECO1. Efficient flight dynamics

VARIABLE STABILITY FLIGHT OPERATIONS MANUAL

Maintenance manual DG-1000S. 0.1 Manual amendments No. Page Description Date 1 0.5, 0.6, diagrams 7, 11, 12

2009 QUICK REFERENCE GUIDE GET INFORMED. ROLL.

Introduction to Aircraft Design and Aviation Systems (ENG3005)

PRODUCT MANUAL SPECIFICATIONS SAFETY PRECAUTIONS. 1460mm/57.48in 1112mm/43.78in 27.74dm²/429.96in² 1600g/56.50oz 57.68g/dm²

PILOT OPERATING HANDBOOK

FLIGHT MANUAL. Bailey-Moyes DRAGONFLY

2014 NIFA CRM Contestant Briefing Guide San Diego, California

Basic Aviation Training Device

B 737 NG El ectrical

Manual for Fire Suppression & Methane Detection System

Scion xb. Pocket Reference Guide. < Contact

737 NG Comm unications

Sport Ice Elektro 124

Chapter 2. Basic Airplane Anatomy Delmar, Cengage Learning

PURPOSE: To provide magneto to engine timing procedures for all TCM engines.

harbor cub Electric Remote Control Airplane Model assembly & Operating Instructions

TECNAM P2002JF. Specification & Description INTRODUCTION

Hydraulic Landing Gear System

1993 ACCESSORIES & EQUIPMENT Volkswagen Instrument Panels. Volkswagen; EuroVan, Passat

For Information Only-Not approved for cockpit use.

Transcription:

Aquila AT01 NORMAL & EMERGENCY CHECKLIST

Daily Pre-flight Check Papers...... On Board Ignition key.... Removed BAT Switch..... On Warning lights (alternator, fuel pressure). Alight Engine instruments..... Check Fuel quantity.. Check External lights... Check for proper operation Bat switch...... Off Foreign objects... Check and Remove ELT Check Baggage Canopy... Stowed and Secured Check for damage and cleanliness EXTERIOR CHECK, VISUAL INSPECTION Flight School Seppe 2

1. Left main landing a) Landing gear strut.. Visual inspection b) Wheel fairing... Visual inspection c) Tire pressure.... Check d) Tire slip marking... Check e) Tire, wheel, brake. Visual inspection f) Brake chocks Remove 2. Tail boom Tail boom shell.. Visual inspection Skid plate.. Visual inspection Tail tie-down.. Disconnect 3. Empennage Elevator. Visual inspection Horizontal stabilizer Visual inspection Rudder... Visual inspection, fitting and bolt connection, proper control cable connection and screw locking. Vertical stabilizer. Visual inspection 4. Right main landing gear a) Landing gear strut.. Visual inspection b) Wheel fairing... Visual inspection c) Tire pressure.... Check d) Tire slip marking... Check e) Tire, wheel, brake. Visual inspection f) Brake chocks Remove Flight School Seppe 3

5. Right wing a) Entire wing surface.... Visual inspection b) Fuel vent... Check if clear c) Flap... Visual inspection d) Aileron and inspection window... Visual inspection e) Wing tip, Nav-light and ACL.. Visual inspection f) Fuel level... Check with dipstick and verify with the indicated fuel level in the cockpit g) Fuel tank filler cap.. Check if closed h) Fuel drain valve... Drain, check for water and deposits i) Wing tie-dow.... Disconnect 6. Nose section, cowling a) Check oil level.. Prior to the oil check, turn the propeller several times in the direction of engine rotation to pump oil from the engine back into the oil tank. a) Check coolant level.... Verify coolant level in the overflow bottle. Should be at least 2/3 full. c) Air intakes (4).. Check if clear d) Radiator / oil cooler intake. Check free from obstructions e) Cowling... Visual inspection, check Camloc fasteners f) Propeller.. Visual inspection g) Propeller blades... Check for cracks / damage h) Spinner dome.. Visual inspection i) Elect. Fuel pump and drain valve Drain, check for water and deposits Flight School Seppe 4

7. Nose landing gear a) Nose gear strut...... Visual inspection b) Wheel fairing... Visual inspection c) Tire pressure.... Check d) Tire slip marking... Check e) Tire, wheel. Visual inspection f) Shock absorber unit... Visual inspection g) Brake chocks and tow bar.. Visual inspection 8. Right wing a) Entire wing surface.. Visual inspection b) Fuel vent.... Check if clear c) Battery..... On d) Stall warning.... Check e) Battery..... Off f) Pitot/static heat..... Remove cover and check if all holes are clear g) Wing tip, Nav-light and ACL... Visual inspection h) Aileron and inspection plates... Visual inspection i) Fuel level..... Check with dipstick and verify with the indicated fuel level in the cockpit j) Fuel tank drain valve... Drain, check for water and deposits k) Fuel tank filler cap.. Check if closed l) Flap... Visual inspection m) Wing tie-dow..... Disconnect Flight School Seppe 5

BEFORE ENGINE START -UP Daily pre-flight check... Completed Passenger briefing.. Completed Seats.... Adjust as required Seat belts and harnesses. Fastened and Tightened Canopy. Closed and Locked Parking brake.. Set Control stick. Check for free movement Carburetor heat... Off Throttle.. Idle Propeller control lever. High RPM Avionics switch.... Off ALT/BAT switch... On Fuel selector valve..... Switch to less fullest tank Alternator 1+2 warning light.. Illuminates Fuel pressure warning light.... Illuminates Anti-collision light (ACL).. On Circuit breakers... Check all in ENGINE START-UP Electrical fuel pump.. On Fuel pressure warning light. Out Throttle -cold engine. IDLE -hot engine. 2 cm Opened Choke -cold engine. Pull -hot engine. Off Brakes.... Set Propeller area... Check if clear Ignition switch.. Start Oil pressure gauge.... Check Alternator 1+2 warning light Off NAV-lights. As required Electrical fuel pump..... Off Flight School Seppe 6

BEFORE TAXIING. Avionics switch / PFD.. On Engine instruments.. Check Voltmeter... Check green range Flaps.... Cruise/UP Avionics and flight instruments Set up TAXIING. Parking brake..... Release Nose wheel steering.. Check function/free movement Brakes... Check Flight instruments and avionics.. Check Compass reading/gyro instruments. Check BEFORE TAKE-OFF Brakes....... Apply Parking brake.... Set Fuel selector valve.. Switch to fullest tank Fuel pressure warning light.. Out Throttle.. Set 1700 RPM Propeller control lever. Switch 3 times b/w High-Low Check RPM drop; 200 ±50 RPM Ignition... Magneto Switch R-Both, L-Both Max drop: 120, diff L/R: 50 Carburetor Heat...... Check (RPM drop: 20-50) Throttle...... Idle Electrical Fuel Pump... On Flaps.. Take-off position Trim...... Check movement, set t/o position Engine instruments..... Checked within Green arc Circuit breakers..... Check all in Control stick..... Check for free movement Seats belts and harnesses Fastened and Tightened Canopy.... Closed and locked Parking brake.. Release Flight School Seppe 7

RUNWAY ITEMS Landing Light... On Runway direction....... Checked Transponder........ ALT Tachometer.. 2200-2260 RPM CLIMB Prop Lever.. Checked 2260 RPM Engine instruments.... Checked Flaps........ Cruise position Climb speed....... 65 KIAS Electrical Fuel Pump... Off CRUISE Cruise power... As required Propeller lever... Between 1650 and 2260 RPM Engine instruments. Checked Fuel balance. Check every 30 min. DESCENT Throttle..... As required Prop lever.. Set 1800-2200 RPM Carburetor heat.... as required Oil/cylinder head temperature... Monitor Flight School Seppe 8

APPROACH Seats belts and harnesses Check Tight Electrical fuel pump.... On Carburetor heat.. On Throttle. As required Airspeed 80 KIAS Flaps... Take-Off position FINAL Flaps... Landing position Prop lever... High RPM Speed.... 60 KIAS Landing light.. On AFTER LANDING Throttle... Idle Flaps.. Cruise/UP Carburetor heat. Off Electrical fuel pump... Off Transponder... Stby Landing Light..... Off ENGINE SHUT DOWN Throttle... Idle Parking brake.. Set Flaps.. Landing position Trim... Take-Off position Avionics switch... Off Ignition switch.... Off (slowly in steps) Electrical Equipment & lights... Off ALT/BAT switch.. Off Hobbs Time... Note Flight School Seppe 9

ENGINE FAILURE DURING TAKE-OFF RUN Throttle...... Idle Brakes. Apply as required ENGINE FAILURE IMMEDIATELY AFTER TAKE-OFF Throttle..... Full OPEN Electrical fuel pump.. On Airspeed...... 70 KIAS Propeller control lever. High RPM Fuel selector valve.. Switch to Fullest tank Choke..... Off Carburetor heat On Ignition switch.. Both Before landing; Fuel selector valve.. Off Ignition switch... Off ALT/BAT switch.. Off ENGINE FAILURE IN FLIGHT Engine Roughness; Carburetor heat On Electrical fuel pump.. On Ignition switch.. Switch to R-Both, then L-Both Throttle..... Do not change position Flight School Seppe 10

If Roughness continues; Throttle........ Reduce to required minimum Precautionary landing....... Perform LOSS OF OIL PRESSURE Oil temperature..... Check If oil pressure falls below the green arc while oil temperature remains normal:...... Land at the nearest airfield If oil pressure falls below the green arc and is accompanied by a rise in oil temperature: Throttle........ Reduce to required minimum Precautionary landing....... Perform LOSS OF FUEL PRESSURE Electrical fuel pump.... On Fuel selector valve.... Switch to Fullest tank Electrical fuel pump.... Off, when warning light FUEL turns off If low fuel pressure warning light remains on; Electrical fuel pump..... On and Land at the nearest airfield Flight School Seppe 11

ENGINE RESTART PROCEDURE WITH STOPPED PROPELLER Non-essential electrical equipment. Off BAT switch... On Propeller control lever. High RPM Fuel selector valve..... Switch to fullest tank Electrical fuel pump...... On Throttle. (hot engine) 2 cm opened (cold engine) Idle Choke. (hot engine) Off (cold engine) Pull Ignition switch.... Both Ignition switch.... Start When power is restored: Oil Pressure..... Check Choke...... Off Electrical equipment.... Switch On as required Oil Temperature.... Check RESTART PROCEDURE WITH PROPELLER WINDMILLING When engine power off and airspeed above 60 kts the propeller auto-rotates; Airspeed.... 76 KIAS BAT switch..... On Fuel selector valve... Switch to fullest tank Propeller control lever.. High RPM Electrical fuel pump.... On Ignition switch. Both Throttle. (hot engine) 2 cm opened (cold engine) Idle Choke. (hot engine) Off (cold engine) Pull Flight School Seppe 12

When power is restored: Oil Pressure..... Check Choke...... Off Electrical equipment.... Switch On as required Oil Temperature.... Check Flight School Seppe 13

POWER-OFF LANDING EMERGENCY LANDING WITHOUT ENGINE POWER Airspeed Flaps in landing position.. 60 KIAS Flaps in Take-off position... 65 KIAS Flaps in Cruise position.... 65 KIAS Fuel selector valve... Off Ignition switch. Off Seats belts and harnesses Tight COM (ATC).. Report location and intention ALT/BAT switch..... Off PRECAUTIONARY LANDING WITH ENGINE POWER Locate suitable field... Consider wind, terrain, obstructions Seats belts and harnesses Tight Initiate descent Select field..... Fly Over Check before turning into final; - throttle.. as required - propeller control lever. High RPM - Carburetor heat... On - Electrical fuel pump On - Flaps.. Extended - Airspeed. 60 KIAS Touch down with lowest possible speed. After Touch down; - Brakes.. Apply - Fuel selector valve.. Off - Ignition switch Off - ALT/BAT switch. Off Flight School Seppe 14

SMOKE AND FIRE ENGINE FIRE ON GROUND Fuel selector valve.. Off throttle.. Full OPEN ALT/BAT switch. Off Ignition switch Off Aircraft...... Evacuate ENGINE FIRE IN FLIGHT Fuel selector valve.. Off Airspeed... 90 KIAS Flaps.. Take-off position Throttle.. Full OPEN Cabin heat.... Off Canopy slide-window Full open Proceed with Power-off landing page 13 ELECTRICAL FIRE AND FORMATION OF SMOKE ON GROUND ALT/BAT switch. Off IF ENGINE IS RUNNING: Throttle.. Idle Fuel selector valve.. Off Ignition switch Off Canopy... Open Fire Extinguisher (if installed).... Activate as required Flight School Seppe 15

ELECTRICAL FIRE AND FORMATION OF SMOKE IN FLIGHT BAT switch.... Off Cabin vents... Open Canopy slide-window. Full open Fire Extinguisher (if installed).. Activate as required CABIN FIRE IN FLIGHT BAT switch... Off Cabin vents... Open Cabin heat.... Off Fire Extinguisher (if installed).. Activate as required If necessary, prepare safety landing INADVERTENT ENCOUNTER OF ICING CONDITIONS In the event of an inadvertent icing encounter, use the following procedure: Carburetor heat. On Propeller RPM... Increase Cabin heat.... On Immediately leave the region in which the icing has occurred. Move the control surfaces periodically, to keep them moveable. POWER OFF GLIDING Flaps.... Retracted Airspeed. 78 KIAS Demonstrated glide ration 14 (4 km/1000 altitude loss) Throttle.. Idle Flight School Seppe 16

SPIN RECOVERY PROCEDURE Rudder... Apply full deflection opposite to direction of rotation Throttle retard to. Idle Elevator control move forward to... Neutral Rudder return to.... Neutral as soon as rotation stops Ailerons return to Neutral Flaps.... Retract if extended Rudder return to.... Neutral as soon as rotation stops Elevator control... Cautiously Pull Out of the dive by applying back pressure on the stick LANDING WITH A FLAT TIRE ELECTRICAL FIRE AND FORMATION OF SMOKE ON GROUND Flaps.... Landing position -Perform touch down on that side of the runway that is opposite of the defective tire, in order to have the complete width of the runway to correct direction changes caused by the defective tire. -Perform touch down with intact main tire first. Touch down nose wheel as soon as possible to obtain a better controllability of the aircraft on the ground -While taxiing, move aileron control fully to the side of the intact main tire, to unload the defective one. -When landing with a flat nose wheel tire; touch down with minimum speed. Hold the nose wheel off the ground as long as possible. Flight School Seppe 17

ELECTRICAL POWER SUPPLY SYSTEM MALFUNCTIONS COMPLETE FAILURE OF ELECTRICAL SYSTEM BAT circuit breaker. RESET if tripped ALT/BAT switch. Check if ON If power is not restored.. Land at nearest airfield ALTERNATOR FAILURE: ALTERNATOR 1 warning light illuminates Alternator switch. Switch OFF then ON Alternator 1 circuit breaker RESET if tripped If alternator warning light remains alight: Alternator1 circuit breaker Pull Alternator switch. Off All non-essential equipment Off Devices connected at 12 VDC receptacle. Off -Observe the voltmeter and ammeter readings -Land at the nearest airfield if practical ALTERNATOR 2 warning light illuminates Alternator 2 circuit breaker RESET if tripped If alternator 2 warning light remains on: Alternator 2 circuit breaker Pull (Alternator 1 takes over power supply) ALTERNATOR 1 and 2 warning lights illuminate Alternator switch. Switch OFF then ON Alternator 1 circuit breaker RESET if tripped Alternator 2 circuit breaker RESET if tripped If alternator 1 & 2 warning light remains on: Alternator1 & 2 circuit breakers Pull Alternator switch. Off Flight School Seppe 18

LOW VOLTAGE INDICATION - Low voltage indication on the ground ; Engine speed.. Increase RPM until the needle moves into the Green arc region. All non-essential equipment.. Turn off until the needle moves into Green arc region. If the needle remains on the green-red shaded arc or below and the ammeter shows discharge Do not fly until problem is eliminated. - Low voltage indication in flight ; All non-essential equipment. Turn off until the needle moves into Green arc region. If the needle remains on the green-red shaded arc or below and the ammeter shows discharge Alternator is defective. Proceed with Alternator failure checklist LOW VOLTAGE INDICATION WHILE LANDING After landing.. Proceed with Low voltage checklist. Flight School Seppe 19

FLAP CONTROL SYSTEM MALFUNCTION FLAP POSITION INDICATOR OR FLAP ACTUATOR MALFUNCTION Flaps circuit breaker.. Reset if tripped Flap position Check visually at the left wing Airspeed.... Within white arc airspeed indic. Flap switch... Switch through all positions. TRIM CONTROL SYSTEM MALFUNCTION TRIM SYSTEM INOPERATIVE Trim actuator circuit breaker.. Reset if tripped Trim switch.. Press Nose Up and then Nose Down for several times Land as soon as practical TRIM ACTUATOR DOES NOT STOP AS DESIRED Control stick... Hold in position Trim actuator circuit breaker.. Pull Trim switch.. Check, whether pressed, jammed, etc. If the problem is obvious, and can be solved: Trim actuator circuit breaker.. Reset If the problem cannot be eliminated:.. Land at nearest airfield Flight School Seppe 20

AVIONICS MALFUNCTION COMPLETE AVIONICS FAILURE Avionics master switch. Switch Off then On. The avionics switch is an automatic circuit protective switch. If the switch trips again; Land at nearest airfield RECEIVE MODE FAILURE OF COM-EQUIPMENT Push to talk switch. Check pilot s & co-pilot s PTT switches whether pressed, jammed, etc..check connectors Head-set. Switch off squelch momentarily If no noise audible: Check headset connectors. TRANSMIT MODE FAILURE OF COM-EQUIPMENT T-symbol... Check whether displayed while transmitting Selected frequency. Check Microphone.... check, if necessary replace headset Flight School Seppe 21

STARTER MALFUNCTION During engine start, the starter does not decouple from engine Throttle. Idle Ignition switch Off Repair damage before conducting planned flight IN-FLIGHT FAILURES AND MALFUNCTIONS SELF ACTUATING RELEASE AND OPENING OF THE CANOPY IN FLIGHT Keep calm, there is no imminent danger Flight attitude.... Stabilize flight attitude/altitude Airspeed 65 75 KIAS Surrounding airspace Check for obstacles/traffic Canopy... Close and lock canopy in flight if possible. Check the canopy locking and the position of the canopy locking lever continuously until landing. If this is not possible to close the canopy, continue flight with open canopy and land at the nearest airfield Flight School Seppe 22