Kalekim Tile Adhesives 17 Tile Adhesives KALEKIM KALEKİMBEYAZ TECHNOFLEX GRANİTECH PROFESYONEL TECHNOBLOCK TECHNOMAX 30 RAPİTECH TECHNOPOOL TECHNOFULL TECHNOLIGHT KALEKİMTOZUMAZ SUPERTECH TECHNOPUR
18 Kalekim Tile Adhesives 1051 KALEKİM Tile Adhesive Cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. High adhesion strength. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİM into 6.5-8 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of KALEKİM with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİM must not be subject to water for at least 24 hours. 5 kg polyethylene bag 25 kg multi-ply paper bags. Technical Temperature Range Grey powder place. 6.5-8 lt water / 25 kg powder 1.3-1.6 lt water / 5 kg powder C1TE TS EN 12004, Class C1TE 1: Normal setting T: Reduced slip E: Extended open time -initial Approx. 6 hours 0.5mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
Kalekim Tile Adhesives 19 1052 KALEKİMBEYAZ White Tile Adhesive White cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. Exterior bonding and grouting of glass mosaics. Interior and exterior bonding of glass bricks. Perfect adherence. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİMBEYAZ into 6.5-8 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application. Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of KALEKİMBEYAZ with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİMBEYAZ must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C1TE TS EN 12004, Class C1TE 1: Standard T: Reduced slip E: Extended open time Technical Temperature Range -initial White powder place. 6.5-8 litres water / 25 kg powder Approx. 6 hours 0.5 mm. After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
20 Kalekim Tile Adhesives 1054 TECHNOFLEX Deformable Tile Adhesive High performance cementitious flexible adhesive with extended open time and reduced slip for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tile, granite. Bonding of tiles on painted walls and gypsum. Bonding of ceramic tiles in swimming pools, basins and any other wet places. Bonding of tiles on terraces and balconies. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly Deformable, resistant to temperature changes. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Extended open time. C2TE S1 TS EN 12004, Class C2TE, S1 T: Reduced slip E: Extended Open Time S1: Deformable Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYP- SASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of TECHNOFLEX into 6-7.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOFLEX with the flat side of trowel, then notch with the toothed side of trowel. s of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNOFLEX should be applied also on the back of tiles. (combined method) Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) Open time is 30 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with TECHNOFLEX must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. Grey or White powder 12 months when stored in the original sealed packing in dry place. 6-7.5 litres water / 25 kg powder Approx. 6 hours 0.5 mm. After 30 minutes 8 hours on wall; 24 hours after on floor 3-5kg./m² 2.5 mm-s1 Deformable
Kalekim Tile Adhesives 21 1055 GRANİTECH Granite Tile Adhesive High performance cementitious adhesive with reduced slip. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, granite, porcelain ceramic, cotto, clinker on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles or marble. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of GRANİTECH into 5.5-7 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of GRANİTECH with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, GRANİTECH should be applied also on the back of tiles. (combined method) Open time is 20 minutes. Install the tiles within this period with pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with GRANİTECH must not be subject to water for at least 24 hours. Since contains cement, irritating to eyes, respiratory system and skin. For further information refer to 25 kg multi-ply paper bags. TS EN 12004, Class C2T T: Reduced slip Technical Temperature Range -initial (after 28 days) Grey or White powder place. 5.5-7 litres water / 25 kg powder Approx. 6 hours 0.5 mm After 20 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
22 Kalekim Tile Adhesives 1056 PROFESYONEL Granite Tile Adhesive High performance cementitious adhesive. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, granite, porcelain ceramic, cotto, clinker on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles or marble. Perfect adherence Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Pour 25kg of PROFESYONEL into 5.5-6.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of PROFESYONEL with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, PROFESYONEL should be applied also on the back of tiles. (combined method) Open time is 20 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceeded, scratch and discard the mortar. Tiles installed with PROFESYONEL must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C2TE TS EN 12004, Class C2 Technical Temperature Range -initial (after 28 days) Grey powder place. 5.5-6.5 litres water / 25 kg powder 6 hours 0.5mm After 20 minutes 8 hours on wall; 24 hours after on floor 3-5kg/m²
Kalekim Tile Adhesives 23 1058 TECHNOBLOCK Aerated Concrete Adhesive Cementitious masonry mortar for bonding high water absorbing construction elements like aerated concrete. Bonding of aerated concrete and any other high water absorbing construction elements. Perfect adherence Labor-cost effective. Pour 25 kg of TECHNOBLOCK into 8-9 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. (A low speed mixer is recommended to mix). Allow to stand for 5-10 minutes to mature. After remixing, the paste is ready for application. trowel of which notch size is 10x10x10mm. While laying the blocks, vertical and horizontal joints should have maximum 3 mm width and fill them completely with TECHNOBLOCK. Open time is 10-15 minutes. Lay the blocks within this 7 period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. 25 kg multi-ply paper bags. Data A (cm) B (cm) C (cm) (kg/m 2 ) 20 50 20 5-8 20 70 20 5-7 30 50 15 3-5 30 70 15 3-4 30 50 20 4-6 30 70 20 4-6 TS EN 998-2 Technical Grey powder 12 months when stored in the original sealed Particle Size Max. 1 mm Temperature Range 8-9 lt water / 25 kg powder Workable Life (EN 1015-9) 5-7 hours Correction Time (EN 1015-9) 5-7 min. Compressive Strength / Class (EN 1015-11) 5 N/mm²/M5 Air Content (EN 1015-7) < % 20 Bond Strength (EN 998-2) 0.3 N/mm² (Table Value) Water Absorption Coefficient (EN 1015-18) 0.17 kg/m² min 0.5 Water Vapor Permeability, μ (EN 1745) 15/35 (Table Value) Thermal Conductivity (EN 1745) NPD (EN 13501-1)
24 Kalekim Tile Adhesives 1060 TECHNOMAX 30 Two Component Highly Deformable Tile Adhesive Two component, high performance cementitious flexible adhesive with reduced slip and extended opentime for ceramic tiles and stones. Exterior bonding of ceramic, granite or porcelain ceramics sized 40x40 cm up to 30 meter and 60x60 cm. up to 15 meter height. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly deformable, resistant to temperature changes. Resistant to all climatic conditions. Can be applied on vertical surfaces even. For bonding of heavy tiles without sagging. Extended open time. Wipe the back side of tiles with water if dusty. Pour 25 kg. of powder component into 5.75 litres of clean liquid slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension. (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOMAX 30 with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNO- MAX 30 should be applied also on the back of the tiles. (combined method) Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. In installation of large size tiles, lay the tiles horizontally and do not start to lay upper row before the below one Leave an expansion joint at every 4 meter and use KALEPOLYMAS. Tiles installed with TECHNOMAX 30 must not be subject to water for at least 24 hours. Powder component: Store in dry medium. Do not stack more than 10 Liquid component: Store in temperatures 5 C to 35 C in original sealed packing. Powder component: 25kg multi-ply paper bags, Liquid component: 5.75lt drums. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. C2TE S2 TS EN 12004, Class C2TE S2 T: Reduced slip E: Extended open time S2: Highly Deformable Technical Temperature Range Set to Light Foot Traffic -initial (after 28 days) Deformability (EN 12002) 1st component: Grey powder, 2nd component: White liquid place 5.75 litres liquid / 25 kg powder 1.5 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 24 hours 4.5-6.5 kg/m² (Combined Method) 5 mm-s2 Highly deformable
Kalekim Tile Adhesives 25 1061 RAPİTECH Fast Setting Tile Adhesive High performance, rapid setting and reduced slip cementitious adhesive for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone and decorative bricks on cementitious renders, cementitious screeds and concrete. Rapid tiling of places like public buildings, cafes, supermarkets, airports, that has to be ready for use within one day. Bonding of tiles on existing ceramic tiles. Fast setting, Perfect adherence. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25kg of RAPİTECH into 6-7 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application. Allow to stand for 5 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of RAPİTECH with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, RAPİTECH should be applied also on the back of the tiles. (combined method) Open time is 15 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. If joints can be grouted with FUGAFLEX or FUGASİM, the site may be open for use within 1 day. Tiles installed with RAPİTECH must not be subject to water for at least 3-4 hours. 25kg multi-ply paper bags. C2FT TS EN 12004, Class C2FT F: Fast Setting T: Reduced slip Technical Temperature Range -initial (after 28 days) -after 6 hours Grey powder place 6-7 litres water / 25 kg powder 45 minutes 0.5 mm After 15 minutes 3-4 hours 3-5 kg/m²
26
Kalekim Tile Adhesives 27 1062 TECHNOPOOL Waterproofing Tile Adhesive High performance, flexible, water resistant cementitious adhesive with extended open time and reduced slip for ceramic tiles and stones. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of all types and sizes of tiles and glass mosaics in swimming pools, Turkish baths, water tanks, basins and any other wet place. Bonding of ceramic tiles or granite on existing granite, ceramic, marble. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Perfect adherence. Highly deformable, resistant to temperature changes. Waterproofing. Extended open time. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. C2TE S2 TS EN 12004, Class C2TE, S2 T: Reduced Slip E: Extended Open Time S2: Highly Deformable Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Wipe the back side of tiles with water if dusty. Pour 25 kg of TECHNOPOOL into 5 5.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOPOOL with the flat side of trowel, then notch with the toothed side of trowel. of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECH- NOPOOL should be applied also on the back of the tiles (combined method). Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) When TECHNOPOOL is used not only as an adhesive but also as a water insulation material, apply mortar both on the substrate and on back side of tiles (combined method). Alternatively, first apply a layer of 1-2 mm of TECHNOPOOL with reinforcement mesh at corners, then install the tiles after 24 hours. Tiles installed with TECHNOPOOL must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags Grey or White powder place 5 5.5 litres water / 25 kg powder 6 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m² 5mm-S2 Highly deformable
28 Kalekim Tile Adhesives 1066 TECHNOFULL Fast Setting Pourable Tile Adhesive High performance, fullcontact & fast setting cementitious flexible adhesive, with extended open time for ceramic tiles and stones. Interior and exterior floor bonding of medium and large sizes of ceramic tiles, granite ceramic, porcelain ceramic, cotto, clinker, marble without the need of backbuttering. Bonding on floors over underfloor heating installations. Bonding on the floors of places subject to heavy traffic like shopping malls, hospitals, schools. Rapid tiling of places like public buildings, cafes, supermarkets, airports, that has to be ready for use within one day. Less consumption, labor-cost effective. 100% coating on the back of the tiles without applying any pressure. Fast setting, Perfect adherence. Semi-fluid consistency, easily trowellable, long open time. High flexibility Resistant to temperature changes. TECHNOFULL may be applied on surfaces up to 2cm thickness. Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Use GYPSASTAR on anhydrite screeds. Pour 20 kg of TECHNOFULL into 4.6-5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). Suitable for bonding of medium and large sizes of tiles on the floors of places subject to heavy traffic without the need of backbuttering. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. If joints can be grouted with FUGAFLEX or FUGASİM, the site may be open for use within 1 day. Tiles installed with TECHNOFULL must not be subject to water for at least 3-4 hours. 20 kg multi-ply paper bags C2FE TS EN 12004 Class C2FE F: Fast Setting E: Extended open time Technical Temperature Range -initial (after 28 days) -after 6 hours Grey powder place 4.6-5 lt water / 20 kg powder 2 hours After 3-4 hours 3-5 kg/m² After 30 minutes
Kalekim Tile Adhesives 29 1069 TECHNOLIGHT Lightweight, Highly Deformable Tile Adhesive Cementitious, high performance, flexible, lightweight tile adhesive including rubber and nano technological additives with extended open time and reduced slip. Interior and exterior floor and wall bonding of all types and sizes of ceramic tiles, natural stone, marble, granite, porcelain ceramic, clinker, cotto on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tile, granite. Bonding of tiles on painted walls and gypsum. Bonding of ceramic tiles in swimming pools, basins and any other wet places. Bonding of tiles on terraces and balconies. Bonding of tiles on places where sudden temperature changes occurs like cold storage depots, on walls of ovens.and over floor heat installations. Bonding of tiles on places subject to heavy traffic like shopping malls, hospitals, schools. Approx. 40% less consumption than standard adhesives. Thus, accomplish the same job with 15 kg package instead of 25 kg standard adhesive. High flexibility with rubber fillers. With its nano technological raw materials, it has high adhesion strength. Easy to carry with light weight and package with handles. C2TE S2 TS EN 12004 Class C2TE, S2 T: Reduced Slip E: Extended Open Time S2: Highly Deformable Environmentally Friendly Highly deformable, resistant to temperature changes. Can be applied on vertical surfaces even for bonding of heavy tiles without sagging. Extended open time. and sufficiently dry. Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Apply KALEKİM DOLGULU ASTAR on plaster surfaces prior to the application. Use GYPSASTAR on anhydrite screeds. Pour 15 kg of TECHNOLIGHT into 6-6.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table) To obtain a good adhesion first apply a thin coat of TECHNOLIGHT with the flat side of trowel, then notch with the toothed side of trowel. Technical Temperature Range -initial (after 28 days) Deformability (EN 12002) of large tiles (greater than 40x40), on existing tiles or which are subject to frost or heavy traffic, TECHNOLIGHT should be applied on the back of the tiles (combined method). Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the mortar. Tiles installed with TECHNOLIGHT must not be subject to water for at least 24 hours. safety data sheet. Do not add any component which is not mentioned in application. bags on top of each other. 15 kg multi-ply paper bags with handles. Grey powder place. (+5 C) (+35 C) 6-6.5 lt water / 15 kg powder 6 hours 0.5mm After 30 minutes 8 hours on wall; 24 hours after on floor 1.5-2.5 kg/m² 5 mm - S2 Highly deformable
30 Kalekim Tile Adhesives 1070 KALEKİMTOZUMAZ Dust-Free Ceramic Tile Adhesive Dust-free cementitious ceramic tile adhesive with extended open time and reduced slip. Floor and wall bonding of all types of ceramic tiles, mosaic and decorative bricks on cementitious renders, cementitious screeds and concrete. Bonding of tiles on existing ceramic tiles. User friendly with dust-free technology. Perfect adherence. Allows installation of tiles from top towards the bottom. Extended open time. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Wipe the back side of tiles with water if dusty. Pour 25 kg of KALEKİMTOZUMAZ into 6-7.5 litres of clean water slowly and mix to obtain a homogeneous paste free from lumps. A low speed mixer is recommended to mix. Do not add any additive which is not mentioned in the instructions for the application Allow to stand for 5-10 minutes to mature. After 1-2 dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of KALEKİMTOZUMAZ with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes, If this period exceed, scratch and discard the mortar. Tiles installed with KALEKİMTOZUMAZ must not be subject to water for at least 24 hours. 25 kg multi-ply paper bags. C1TE TS EN 12004, Class C1TE 1: Normal setting T: Reduced slip E: Extended Open Time Environmentally Friendly Technical Temperature Range -initial Grey powder place. 6-7.5 lt water / 25 kg powder 6 hours 0.5 mm After 30 minutes 8 hours on wall; 24 hours after on floor 3-5 kg/m²
Kalekim Tile Adhesives 31 1230 SUPERTECH Ready to Use Tile Adhesive Ready to use high performance emulsion polymer based tile adhesive with extended open time and reduced slip for ceramic tiles and stones. Easy and clean application for interior wall and floor bonding of all types and sizes of ceramic tiles even on deformable surfaces Bonding of tiles on gypsum panels and painted walls Bonding of Ecocarat Interior bonding of insulating and decorative ceiling materials. Ready to use. Perfect adherence. Highly deformable, resistant to normal vibrations to which building materials are subject. Extended open time. Allows installation of tiles from top towards the bottom. Use TAMİRART or MASTAR 10 in case of uneven substrates to get a sound and flat surface. Mix SUPERTECH thoroughly before application. Spread the SUPERTECH onto the substrate with notched trowel of which notch size is appropriate to the tile dimension (See Notch Size Recommendation Table). To obtain a good adhesion first apply a thin coat of SUPERTECH with the flat side of trowel, then notch with the toothed side of trowel. Open time is 30 minutes. Install the tiles within this period with a firm pressure. Unfavourable climatic conditions (high temperature, low humidity, wind, etc) can reduce this time to just a few minutes. If this period exceed, scratch and discard the paste. Insulating panels and decorative ceiling tiles can be applied either spot-bonding or full bonding. Tiles installed with SUPERTECH must not be subject to water for at least 10 days. While bonding the tiles on existing tiles, curing time may increase increase up to 1-2 weeks. Although SUPERTECH is non hazardous, use normal precautions for handling chemical products. For further information refer to Store in dry and cool medium. 1.5 kg, 5 kg, 15 kg and 30 kg pail. D2TE TS EN 12004, Class D2TE D: Dispersion based T: Reduced slip. E: Extended Open Time Technical Temperature Range Shear Adhesion Strength (EN 1324) -initial (after 28 days) -at elevated temperatures White paste place. 0.5 mm After 30 minutes 24-48 hours 1.5-2 kg/m² (-30 C) - (+80 C)
32 Kalekim Tile Adhesives 1411 TECHNOPUR Solvent-free Polyurethane Adhesive Two component, solvent-free polyurethane based multi-purpose adhesive. Bonding ceramic, granite ceramic, on concrete, metal, fibre-cement, wood, plasterboard surfaces. Bonding parquet. Bonding on floors over floor heating installations. Bonding thin tiles (Kalesinterflex ) reinforced with fibre mesh. Solvent-free. Excellent flexibility. Perfect adherence For floor heating systems, the heating should start ten days earlier and be stopped at the time of application. System can be reoperated 72 hours after the application. Mix 6.250 kg component A with 0.750 kg component B until a homogeneous color is obtained. Spread the mixture onto the substrate with notched trowel of 4x4x4 mm size. In bonding, sizes 40x40 cm or larger, apply the mixture using backbuttering method. Bonding of tiles and parquets on the substrate surfaces must be applied in 45-60 minutes. tools and surface with polyurethane cleaning materials. Contains Difenylmethane 4.4 - diisosyanate which can be harmful. Do not breathe vapor. Use in well ventilated areas. In case of contact with skin and eyes rinse immediately with plenty of water and seek medical advice. Wear suitable protective clothing, gloves and eye protection. Keep away from children. Keep products as lids closed. Store in dry medium. 7 kg pail (2 components). and sufficiently dry. Cementitous substrates must be Use TAMİRART or MASTAR 10 in case of any loose and uneven substrates to get a sound and flat surface. R2T TS EN 12004 Class R2T R: Resin based T: Reduced slip Technical (at 23 C and 50% RH) Color Component A: Light yellow. Component B: Dark brown. 12 months when stored in the original sealed packing in dry place. Component A: 6.25 kg Component B: 0.75 kg Pot life 45-60 minutes. Setting Time 80% hardening in 24 hours. 100% hardening in 1 week. 0.5mm ~ 1.5 kg (4x4x4 mm. notched trowel). Shear Adhesion Strength (TS EN 12003) - inital 2 N/mm 2 - after immesion in water 2 N/mm 2 - after thermal shock 2 N/mm 2 Service Temperature Range (-30 C) - ( +80 C)
33
34 Kalekim Yapı Kimyasalları