CATALOGUE INDUCTIVE SENSORS IAS

CATALOGUE INDUCTIVE SENSORS IAS

Registration No.: 17-01 Testing laboratory accredited according to DIN EN 45001 Reg.-No. DAT-P-048/95-00 For all transactions, the newest of the General Conditions of Sale and Delivery for Products and Services of the Industry ZVEI shall apply, along with the supplementary conditions extended reservation of proprietary rights, together with the supplements listed on our order confirmations and/or invoices. All specifications are subject to change without notice. Reprint, even in part, only with our consent. RECHNER Germany 09/004 GB - Printed in EU, all rights reserved. Edition September 004 With publication of this catalogue all former printed catalogues about RECHNER inductive sensors are invalid. All specifications are subject to change without notice. (08/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TABLE OF CONTENTS CATALOGUE INDUCTIVE SENSORS IAS GES TECHNOLOGY... 4-5 ADJUSTMENT... 6 TYPICAL CURVES... 7 MOUNTING... 8-9 TECHNICAL TERMS... 9-10 APPLICATION EXAMPLES... 11 SERIES... 1 TYPE CODE... 1 CYLINDRICAL HOUSINGS... 15-56 ATEX/StEx SERIES 10/0...57-60 ATEX AND ATEX/StEx SERIES 0 (NAMUR)... 61-74 INDUCTIVE HIGH-TEMPERATURE SENSORS...75-84 FEMALE CONNECTORS... 85 MOUNTING BLOCKS... 86 FEMALE CONNECTOR, SCREENED... 86 PROTECTION CAPS AND PROTECTION SETS... 87 NORMS... 88-89 SPECIFICATION FOR EXPLOSION PROTECTION... 90 TYPE SELECTION IN ARTICLE NUMBER ORDER... 91-9 TYPE SELECTION IN TYPE DESCRIPTION ORDER... 9-94 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TECHNOLOGY The inductive sensors, our abbreviation IAS, contain a transistor oscillator whose power consumption is influenced by the approach of metals and other electrically conductive s. This effect can also be achieved through a non-conductive. Depending on the type, the current change of the oscillator will be amplified to a streamlined output signal or output as a binary signal by a switching amplifier. stages with npn or pnp transistors are available for DC operation. A transistor output stage or FET-output is integrated for AC connection The output switching functions are NO, NC or change-over (antivalent), similar to mechanical switches. Electronic circuits, PLCs, relays or contactors can be activated directly with inductive sensors. The current change in the oscillator is caused without contact by the approach of the actuating to the active area. The damping of the oscillator is possible between the active and specified maximum sensing distance (Sn) + 10 %. No mechanical force is exerted on the actuating in the process, and no magnetic effect is caused by the high-frequency alternating field. The components of the IAS are mounted in plastic or metal casings and encapsulated with epoxy casting resin. The plastics used for the housings are:! PVC (polyvinylchloride)! (polyamide) 6.6 glass-fibre reinforced! PC (polycarbonate)! PTFE (polytetrafluor ethylene)! PEEK (polyetheretherketone) And the metal housings are! brass / chrome or nickel-plated! VA stainless-steel, No. 1.401 or No. 1.405.! Aluminium die-cast By means of the following measures all devices are insensitive to dirt, vibration (vibration stability: 0 g, 100...000 Hz, 1 hour) and are watertight (depending on the type, up to IP 68). The choice of housings enables a wide range of applications, e.g. with aggressive media, in hot areas or in areas subjected to steam. Only pre-tested electronic components, proven integrated circuits and hybrid circuits are used and produced with SMT. The standard constant permitted is -5 up to +70 C, and up to 90 C for brief periods. High-temperature types for use from -00 up to +50 C are also included in our general product line. With contactless detection no physical actuating force is required for operation. There is no contact bounce, no sensor wear, no maintenance and the service life is independent of the switching frequency. IAS can be used in machines, systems and vehicles as limit switches, contactless position switches for monitoring and positioning, as pulse generators for counting tasks, distance and speed measurements, and for many other applications (for application examples see page 11). All specifications are subject to change without notice. (07/004) 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TECHNOLOGY Wiring of the inductive sensors should be routed separately or screened from heavy conductor lines, as in extreme cases inductive peak voltages can destroy the sensors despite the integrated protective circuit. Screened cable or twisted lines are recommended, especially for longer cable runs > 5 m. Direct control of electric light bulbs is to be avoided, because during the switch-on moment cold current is many times the rated current and can destroy the output stage of the sensor. Units with strong local fields, e. g. high power walkie-talkies, or noise sources in the lower frequency range, e.g. long, middle or short wave transmitters should not be operated close to the sensors or additional measures have to be taken in order to eliminate their maloperation. - and -wire sensors with binary output can be used in series or parallel connection, similar to mechanical contacts. The type-typical voltage drop and the residual voltage U d, which must be multiplied in accordance with the number of sensors for series connection, must be noted. In the case of parallel connection of sensors with thyristor output, the first switched output takes over the total load current. Series connection Parallel connection wire AC/DC wire DC NPN All specifications are subject to change without notice. (05/004) wire DC PNP RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 5

ADJUSTMENT Analog inductive sensors are equipped with a 0-turn spindle potentiometer. This allows adjustment of an application specific operating range between the minimum distance 0 mm and the type-typical maximum value. Consequently, the full output current range (4...0 ma) is always present, regardless of the required measuring distance. The analog sensors of series 10 are designed with a -colour LED that facilitates adjustment. Outside the operating range I A < 4 ma and I A > 0 ma green light is emitted to display operational readiness. Within the operating range of 4...0 ma the LED is yellow. In the undamped state the output current value is > 0 ma and moves with the reduction of the object distance toward 4 ma (value at total damping approx..5 ma). The data of the nominal sensing distance are based on the measuring method according to DIN VDE 0660, Part 08. The respective nominal sensing distance is indicated with a tolerance of + 10 %. The standard measurement plate is square with a thickness of 1 mm and is made of carbon steel FE 60 (defined in ISO 60: 1980 ) with a smoothed and earthed. The side lengths are equal to the diameter of the active area of the IAS or equal to x Sn, depending on which value is greater. With a different or a smaller of the actuating element, the sensing distance is smaller Sensing distance Adjustment of the sensing distance of the inductive analogue sensors is made by means of a spindle potentiometer with the screwdriver provided. Typical response-time characteristic The possible sensing distance on a particular metal can be worked out by means of the typical reduction factors: Sensing distance = Sn x reduction factor. Metal type: FE 60 St 7 Reduction factor approx. CrNi V A For size M0x1.5 / 0: First open plastic tab. For size > M0x1.5 / 0: First remove plastic sealing screw. V 4A 1 1 0.85 0.75 0. 7 0.45 0. 4 0. 0.4 Ms Al Cu Au All specifications are subject to change without notice. (05/004) 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TYPICAL CURVES A B A = IAS 10-A1-IL B = IAS-10-A14-IL Parameter: Tu = 5 C, UB = 4 V DC Actuator: Stainless steel St 7, 1 mm thick, square, side length equal to the diameter of the active area. Typical curves of flush mountable analogue sensors C D C = IAS 10-A-IL D = IAS-10-A4-IL Parameter: Tu = 5 C, UB = 4 V DC Actuator: Stainless steel St 7, 1 mm thick, square, side length equal to the diameter of the active area. All specifications are subject to change without notice. (05/004) Typical curves of non-flush mountable analogue sensors RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 7

MOUNTING There are two different types of inductive sensors: 1. For flush mounting in metal and other s. These sensors can also be mounted close together (see Fig. 1 and ).. For non-flush mounting in metal. However, these types can also be mounted flush in nonmetals. When mounting two or more sensors side by side a space / free zone must be provided (see Fig. and 4). Mounting Fig.1 Fig. FREE ZONE no damping e Fig. The dimension e corresponds to the threadfree area of standard sensor types (-A1-...). Otherwise e is 7 mm. Fig.4 For opposing active areas a, x Sn For non-flush mountable Sensors distance b has to be 1,5 x Sn. All specifications are subject to change without notice. (05/004) 8 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

MOUNTING The and -dependent maximum torque should be taken into consideration in order to prevent damage to the threaded sleeves when mounting. The values listed in the table are based on the use of the nuts supplied with the sensors. Material Thread PVC 6. 6 PTFE Brass Stainless Steel M 5 x 0.5 - - - - 1.5 Nm M 8 x 1 - - - - 4.5 Nm M 1 x 1 1.5 Nm 1 Nm 0. Nm 16 Nm 5 Nm M 18 x 1-1.7 Nm 0.5 Nm 8 Nm 60 Nm M x 1.5 1 Nm 6 Nm 1.4 Nm Nm 84 Nm M 0 x 1.5-8 Nm.5 Nm 8 Nm 00 Nm M x 1.5-1 Nm Nm 150 Nm 0 Nm Due to the permitted thread tolerances specified in German standard DIN 1, the maximum screw-in length for threaded sensors should be taken into consideration. Depending on that the length of the threaded block for screwing in proximity sensors should not exceed the following dimensions. In the case of larger threaded blocks we recommend drilling a blind hole in order to adhere to the maximum screw-in length. Thread: M 5 x 0. 5 M 8 x 1 M 1 x 1 M18 x 1 M x 1. 5 M 0 x 1. 5 M x 1. 5 All specifications are subject to change without notice. (05/004) Screw-in length max. mm 6 mm 8 mm 1 mm 1 mm 1 mm 1 mm TECHNICAL TERMS Unless otherwise specified technical data is as follows: +4 C, U B = 8 V DC for IAS-0; U B = 4 V DC for IAS-10 and IAS-0 and U B = 0 V AC for IAS-60. sensing distance / S a Within the operating sensing distance the sensor operates reliably taking in to account all the possible tolerances. It lies between 0 and 0.81 x S n. Power up time delay The time the sensor needs to be ready for operation after connecting the operating voltage. It is in the milliseconds range. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 9

TECHNICAL TERMS s The application of the housing s used is based on the technical specifications of the and of the manufacturer. Even though RECHNER Sensors have far-reaching application experience concerning the use of different housing s, the customer is responsible for checking in each case that the housing is suitable for the application. Cable For the standard models PVC- or PUR-cable are used. One has to take into consideration that the cable should not be moved with s below 5 C. PVC is not suitable for use in applications with oil-based liquids or with UV-radiation. PUR is not suitable for continuous contact with water. For special application areas silicone or PTFE cables are available. Nominal sensing distance / S n The characteristic value of a proximity sensor, without consideration of production tolerances and variations due to temperature and voltages. Real sensing distance / S r The sensing distance determined at +0 C and rated voltage. Here the series variance is taken into consideration. Variation max. + 10 %. Reduction factors The reduction factors, as shown in the table on page 6, should be taken into consideration, for metals other than FE 60 or ST 7. Series- and parallel connection It is possible to connect the proximity sensors in series or parallel. When considering this it must be taken into account that the voltage drops are added for series connection and the residual voltages for parallel connection. Under these circumstances it is advisable to operate a maximum of three sensors in a corresponding circuit. Repeat accuracy of the switching point The variation of the switching point of two successive measurements at constant ambient conditions. Frequency of operating cycles The maximum damping and un-damping cycles of the proximity sensor within one second. To ascertain the frequency of operating cycles a pulse / break ratio of 1 : is used as a basis, at S n ½. Switching hysteresis The difference between the switch-on and switch-off point of a proximity sensor, when approaching or moving away from the standard measuring plate. It is < 0% of the real sensing distance. Enclosure rating IP 65: Protection against contact with voltage-carrying parts, protection against ingress of dust and water jet. : Protection against contact with voltage-carrying parts, protection against ingress of dust and protection against ingress of water when the equipment is immersed in water, up to 1 m depths and for a period of 0 minutes. Temperature variation The displacement of the switching point if the changes. All specifications are subject to change without notice. (05/004) 10 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

APPLICATION EXAMPLES Fig. 1: Inductive level control within a plastic container at a by-pass, by means of a metal float Fig. : Position aid for transported tins Fig. : Detection of a gear wheel or cam wheel Fig. 4: Counting of metal containers All specifications are subject to change without notice. (05/004) Fig. 5: Position aid for the gripper of industrial robots RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 11

SERIES The series 10 contains inductive -wire proximity sensors with digital output pnp with NO or NC-function. Electronic circuits, PLC s, relays and our power supplies of series 10 can be directly activated. Analog sensors with 4...0 ma output are also available. The operating range of these analog sensors is adjustable by means of a potentiometer and they can be actuated by analog interfaces with internal resistance Ri < 00 ohm. The sensors are reverse polarity protected, overload protected and have electronic shortcircuit protection. StEx-Sensors for use in Zone 0 with ATEX-certificate complete this series. The series 0 contains inductive -wire proximity sensors with digital output npn with NO or NC-function. Electronic circuits, PLC s, relays and our power supplies of series 10 can be directly activated. The sensors are reverse-polarity protected, overload-protected and have electronic short-circuit protection. StEx-Sensors for use in Zone 0 with ATEX-certificate complete this series. The series 0 contains inductive -wire proximity signal generators according to NAMUR DIN 60947-5-6 These sensors can be mounted in explosion hazardous areas when they are connected to approved isolating switching amplifiers with intrinsically safe control circuits. [EExia] or [EExib], our series N-11... Depending on which isolating switching amplifier is used the NAMUR-sensors of this series can be used up to zone 1. The data specified in the certificate of conformity of the isolating switching amplifier used must be taken into consideration. StEx-Sensors for use in Zone 0 with ATEX-certificate complete this series. The series 60 contains inductive -wire AC/DC proximity sensors with digital output with NO and NC function. AC/DC relays, conductors, solenoid valves can be activated directly. PLCs with AC inputs can also be connected if the minimum load current is taken into consideration. The sensors have a protective circuit against high induction voltages. For increased requirements for the permitted range of our inductive proximity sensors, we offer the series up to +100 C with integrated electronic as a -Wire DC. The sensors are available with housings made of PTFE, PTFE/VA or PTFE/brass and have a silicone connection cable. For extreme ambient or product-temperature conditions, our high temperature sensors up to +50 C are available with external electronics. The sensors are integrated in PEEK, PTFE, PEEK/VA or PTFE/VA housings. For the rectangular sensors housings in PEEK/aluminium are used. The FEP-coated sensor cable with VA grid screening, in the lengths, 5 or 10 m, is the connection to the evaluation unit and may also be used under high-temperature conditions. The evaluation unit is connected to the sensor by means of a plug-in connector. On the sensor side the cable is permanently cast in or equipped with a temperatureresistant plug-in connector (...Y-). The sensing distance for high temperature sensors can be adjusted on the evaluation unit and the switching state is displayed by an LED. The sensing distance adjustment should be made at operating temperature. Here the maximum specified sensing distance and the temperature drift must be taken into consideration. All specifications are subject to change without notice. (05/004) 1 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TYPE CODE IAS-...-...-...-...-...-...-... if existing Y... = with flange connector if existing e. g. 100 C,... = higher temperature range D = with manufacturer certificate according to ATEX StEx = StEx according to ATEX if existing e. g. PTFE, PTFE/Ms,... = housing if existing M... = thread size K = plastic housing A = Antivalent function (NO/NC) IL = Analogue function N = NAMUR Ö = NC S = NO A... = European standard (M).../... = Thread C = Rectangular housing NPN, PNP = function 04, 6.5, 40,... = Version 10 = -wire/4-wire DC PNP/ -wire analogue 0 = -wire/4-wire DC NPN 0 = NAMUR DIN 60947-5-6 60 = -wire AC/DC AC/DC metal have an earth wire. Pluggabel have an additional pin. = Inductive Proximity Sensor All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 1

14 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de All specifications are subject to change without notice. (05/004)

CYLINDRICAL HOUSINGS I S ensing distance [mm] Diameter [mm] Version Pages T range [mm] analogue or with thread DC AC/DC E 10...5 V 0...50 V Cable, Connecto r M B rass [Ms] N PN [0] AC/DC [60] Cable S tainless steel [VA] P NP [10] Connector [Y... ] Polyamide [] Polyvinylchloride [PVC] Selection NO (S), NC (Ö) and Y7 = Metal M8 x 1 Antivalent (A with 10, 0 only) Y =PlasticM1 x1 see data sheet Y5 = Metal M1 x 1 DC 10...0 VDC flush non-flus h A nalogue [IL] 1 0. 8-4 VA 10, 0 Cable 16 0. 8 - M5 x 0. 5 VA 10, 0 Cable, Y7 17-18 1. 5-6. 5 VA 10, 0 Cable, Y7 19-1 4 1 M8 x 1 - A11/A 1 10, 0 Cable VA 1.5 - M8 x 1 10 Cable, Y7-5 5-5 11 10 Cable 6 6 4 M1 x 1 - A1/A - 5 M1 x 1 VA, Brass/PVC 10, 0, 60 Cable, Y5 7- PVC 60 Cable 7 5 8 0...5 0... 8 M18 x 1 - A1/A Brass 10, 0, 60, IL Cable, Y, Y5 4-4 8-10 M x 1. 5 10 Cable 4 9 10-0 Brass 0 Cable 44 All specifications are subject to change without notice. (05/004) 10 10 15 0...10 0...15 M0 x 1.5 - A14/A4 Brass 10, 0, 60, IL Cable, Y 45-5 11 0-40 10, 60 Cable 5-54 1-5 50 10, 0 Cable 55 1-40 60 10 Cable 56 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 15

Series 0 - NPN Series 10 - PNP Ø = 4 mm : stainless steel VA Flush mountable Sensing distance Sn = 0.8 mm distance Sn [mm], flush mounting 0.8, yes 0.8, yes NPN -wire DC -wire DC NO IAS-0-04-S NC IAS-0-04-Ö 1 610 1 650 1 PNP IAS-10-04-S IAS-10-04-Ö 11 610 11 650 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma khz khz -5...+70 C -5...+70 C red built-i n red built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 - - - - 1 4 5 6 All specifications are subject to change without notice. (05/004) 16 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M5 x 0.5 : stainless steel VA Flush mountable Sensing distance Sn = 0.8 mm distance Sn [mm], flush mounting 0.8, yes 0.8, yes NPN -wire DC -wire DC NO IAS-0-M5-S NC IAS-0-M5-Ö 14 010 14 110 1 All specifications are subject to change without notice. (05/004) PNP IAS-10-M5-S IAS-10-M5-Ö 114 010 114 110 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma khz khz -5...+70 C -5...+70 C red built-i n red built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 - - 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 17

Series 10 - PNP M5 x 0.5 : stainless steel VA Flush mountable Sensing distance Sn = 0.8 mm With metal flange connector M8 x 1 distance Sn [mm], flush mounting 0.8, yes 0.8, yes NPN -pin DC -pin DC NO NC PNP IAS-10-M5-S-Y 7 IAS-10-M5-Ö-Y 7 114 400 114 450 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 metal flange connector M8 x 1 metal flange connector M8 x 1 VA No. 1.405 VA No. 1.405 - - 1 4 5 6 All specifications are subject to change without notice. (05/004) 18 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP Ø = 6.5 mm : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm distance Sn [mm], flush mounting 1.5, yes 1.5, yes NPN -wire DC -wire DC NO IAS-0-6.5/15- S 14 500 1 NC All specifications are subject to change without notice. (05/004) PNP IAS-10-6.5/15- S IAS-10-6.5/15- Ö 114 500 114 650 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 PVC - - PVC 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 19

Series 10 - PNP Ø = 6.5 mm : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm distance Sn [mm], flush mounting 1.5, yes 1.5, yes NPN -wire DC -wire DC NO NC PNP IAS-10-6.5-S-LE D IAS-10-6.5-Ö-LE D 114 510 114 610 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 PVC - - PVC 1 4 5 6 All specifications are subject to change without notice. (05/004) 0 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP Ø = 6.5 mm : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm With metal flange connector M8 x 1 distance Sn [mm], flush mounting 1.5, yes 1.5, yes NPN -pin DC -pin DC NO NC All specifications are subject to change without notice. (05/004) PNP IAS-10-6.5-S-Y 7 IAS-10-6.5-Ö-Y 7 114 900 115 000 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 Metal flange connector M8 x 1 Metal flange connector M8 x 1 VA No. 1.405 VA No. 1.405 PVC - - PVC 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 1

Series 0 - NPN Series 10 - PNP M8 x 1 : stainless steel VA Flush mountable Sensing distance Sn = 1 mm distance Sn [mm], flush mounting 1, yes 1, yes NPN -wire DC -wire DC NO IAS-0-A11- S 00 500 1 NC PNP IAS-10-A11- S IAS-10-A11- Ö 100 500 101 010 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 PVC PC PVC PC 1 4 5 6 All specifications are subject to change without notice. (07/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP M8 x 1 : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm distance Sn [mm], flush mounting 0.8, yes 0.8, yes NPN -wire DC -wire DC NO NC All specifications are subject to change without notice. (07/004) PNP IAS-10-M8-S IAS-10-M8-Ö 100 110 100 00 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 PVC - - PVC 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP M8 x 1 : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm With metal flange connector M8 x 1 distance Sn [mm], flush Mounting 1.5, yes 1.5, yes NPN -pin DC -pin DC NO NC PNP IAS-10-M8-S-Y 7 IAS-10-M8-Ö-Y 7 100 00 100 10 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 metal flange connector M8 x 1 metal flange connector M8 x 1 VA No. 1.405 VA No. 1.405 PVC - - PVC 1 4 5 6 All specifications are subject to change without notice. (07/004) 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M8 x 1 : stainless steel VA Non-flush mountable Sensing distance Sn = mm distance Sn [mm], flush mounting, no, no NPN -wire DC -wire DC NO IAS-0-A1- S 01 00 1 NC All specifications are subject to change without notice. (07/004) PNP IAS-10-A1- S IAS-10-A1- Ö 101 00 101 50 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 5 % 5 % No-load current (I ) typ. 10 ma o Protective circuit typ. 10 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 PVC PC PVC PC 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 5

Series 10 - PNP Ø = 11 mm : Non-flush mountable Sensing distance Sn = 5 mm distance Sn [mm], flush mounting 5, no 5, no NPN -wire DC -wire DC NO NC PNP IAS-10-14-S IAS-10-14-Ö 115 00 115 50 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm 1 4 5 6 All specifications are subject to change without notice. (05/004) 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M1 x 1 : stainless steel VA Flush mountable Sensing distance Sn = mm distance Sn [mm], flush mounting, yes, yes NPN -wire DC -wire DC NO IAS-0-A1- S NC IAS-0-A1- Ö 01 700 01 900 1 All specifications are subject to change without notice. (05/004) PNP IAS-10-A1- S IAS-10-A1- Ö 101 700 101 900 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 7

Series 0 - NPN Series 10 - PNP M1 x 1 : stainless steel VA Flush mountable Sensing distance Sn = mm With metal flange connector M1 x 1 distance Sn [mm], flush mounting, yes, yes -pin DC -pin DC NO NPN IAS-0-A1-S-Y 5 0 00 1 NC PNP IAS-10-A1-S-Y 5 IAS-10-A1-Ö-Y 5 10 00 10 50 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 metal flange connector M1 x 1 metal flange connector M1 x 1 VA No. 1.405 VA No. 1.405 - - 1 4 5 6 All specifications are subject to change without notice. (05/004) 8 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 60 - AC/DC M1 x 1 : brass/pvc Flush mountable Sensing distance Sn = mm distance Sn [mm], flush mounting, yes, yes All specifications are subject to change without notice. (05/004) -wire AC/DC -wire AC/DC NO IAS-60-A1- S NC IAS-60-A1- Ö 600 00 600 500 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma typ. 6 V residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm² brass/pvc 1 m x 0.14 mm² brass/pvc RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 9

Series 0 - NPN Series 10 - PNP M1 x 1 : stainless steel VA Non-flush mountable Sensing distance Sn = 4 mm distance Sn [mm], flush mounting 4, no 4, no NPN -wire DC -wire DC NO IAS-0-A- S NC IAS-0-A- Ö 0 400 0 500 1 PNP IAS-10-A- S IAS-10-A- Ö 10 400 10 500 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm m x 0.14 mm VA No. 1.405 VA No. 1.405 1 4 5 6 All specifications are subject to change without notice. (05/004) 0 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M1 x 1 : stainless steel VA Non-flush mountable Sensing distance Sn = 4 mm With metal flange connector M1 x 1 distance Sn [mm], flush mounting 4, no 4, no -pin DC -pin DC NPN IAS-0-A-Ö-Y 5 0 050 NO NC All specifications are subject to change without notice. (05/004) PNP IAS-10-A-S-Y 5 IAS-10-A-Ö-Y 5 10 001 10 050 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 150 ma 150 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 metal flange connector M1 x 1 metal flange connector M1 x 1 VA No. 1.405 VA No. 1.405 - - 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 1

Series 60 - AC/DC M1 x 1 : brass/pvc Non-flush mountable Sensing distance Sn = 4 mm distance Sn [mm], flush mounting 4, no 4, no -wire AC/DC -wire AC/DC NO IAS-60-A- S 1 NC IAS-60-A- Ö 600 700 600 900 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma typ. 6 V residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.14 mm² brass/pvc m x 0.14 mm² brass/pvc All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 60 - AC/DC M1 x 1 : PVC Non-flush mountable Sensing distance Sn = 5 mm distance Sn [mm], flush mounting 5, no All specifications are subject to change without notice. (05/004) -wire NO AC/DC IAS-60-14-S-M1 614 900 1 voltage (U ) 0...50 V AC/DC B Ourtput current max. (I ) 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d residual ripple max. - No-load current (I ) typ..5 ma o Protective circuit 5 Hz -5...+70 C yello w built-i n of protection IEC 59 cable m x 0.14 mm² 1 PVC PVC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M18 x 1 : brass Flush mountable Sensing distance Sn = 5 mm distance Sn [mm], flush mounting 5, yes 5, yes 5, yes NPN -wire DC -wire DC 4-wire DC NO IAS-0-A1- S NC Antivalen t IAS-0-A1- A 0 100 0 060 1 PNP IAS-10-A1- S IAS-10-A1- Ö 1 4 5 6 IAS-10-A1- A 10 100 10 00 10 060 4 5 6 voltage (U ) 10...5 V DC 10...5 V DC 10...5 V DC B current max. (I ) 50 ma 50 ma x 50 ma e Load current min. - - - Voltage drop max. (U ) <.5 V <.5 V <.5 V d 10 % 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma typ. 15 ma khz khz khz -5...+70 C -5...+70 C -5...+70 C yello w built-i n yello w built-i n green/yello w built-i n of protection IEC 59 cable m x 0.4 mm brass m x 0.4 mm brass m x 0.4 mm 4 brass All specifications are subject to change without notice. (05/004) 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

With Analogue Series 10 - IL M18 x 1 : brass Flush mountable range 0...5 mm adjustable All specifications are subject to change without notice. (05/004) range [mm], flush mounting 0...5, yes Linear range [mm] 1.5... 5 function analogue -wire DC analogue IAS-10-A1-I L 105 750 see below voltage (U ) 15...0 V DC B current max. (I ),5...> 0 ma e 5 % No-load current (I ) typ. 40 ma o current active free > 0 ma O utput current active covered < 0...< 4 ma Load resistor R L = 0...00 Ohm Protective circuit 0...+60 C green/yellow/gree n built-i n of protection IEC 59 cable m x 0.4 mm brass PTFE RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 5

Series 0 - NPN Series 10 - PNP M18 x 1 : brass Flush mountable Sensing distance Sn = 5 mm With metal flange connector M1 x 1 distance Sn [mm], flush mounting 5, yes 4-pin DC Antivalen t NPN IAS-0-A1-A-Y 5 0 067 PNP IAS-10-A1-A-Y 5 10 068 6 voltage (U ) 10...5 V DC B current max. (I ) x 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit khz -5...+70 C yello w built-i n of protection IEC 59 metal flange connector M1 x 1-1 4 5 6 brass All specifications are subject to change without notice. (08/004) 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

With Analogue Series 10 - IL M18 x 1 : brass Flush mountable range 0...5 mm adjustable With plastic flange connector M1 x 1 All specifications are subject to change without notice. (07/004) range [mm], flush mounting 0...5, Linear range [mm] 1.5... 5 function -wire yes DC analogue analogue IAS-10-A1-IL-Y 105 751 see below voltage (U ) 15...0 V DC B current max. (I ),5...> 0 ma e 5 % No-load current (I ) typ. 40 ma o current active free > 0 ma O utput current active covered < 0...< 4 ma Load resistor R L = 0...00 Ohm Protective circuit 0...+60 C green/yellow/gree n built-i n of protection IEC 59 plastic flange connector M1 x 1 - brass PTFE RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 7

Series 60 - AC/DC M18 x 1 : brass Flush mountable Sensing distance Sn = 5 mm distance Sn [mm], flush mounting 5, yes 5, yes -wire AC/DC -wire AC/DC NO IAS-60-A1- S NC IAS-60-A1- Ö 601 000 601 00 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ. 6 V typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.4 mm² brass 1 m x 0.4 mm² brass All specifications are subject to change without notice. (05/004) 8 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M18 x 1 : brass Non-flush mountable Sensing distance Sn = 8 mm distance Sn [mm], flush mounting 8, no 8, no NPN -wire DC 4-wire DC NO IAS-0-A- S Antivalen t IAS-0-A- A 05 800 05 780 1 All specifications are subject to change without notice. (05/004) PNP IAS-10-A- S IAS-10-A- A 105 800 105 780 4 6 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma x 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n green/yello w built- in of protection IEC 59 cable m x 0.4 mm brass 1 4 5 6 m x 0.4 mm 4 brass RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 9

With Analogue Series 10 - IL M18 x 1 : brass Non-flush mountable range 0...8 mm adjustable range [mm], flush mounting 0...8, no Linear range [mm]... 8 function analogue -wire DC analogue IAS-10-A-I L 108 50 see below voltage (U ) 15...0 V DC B current max. (I ),5...> 0 ma e 5 % No-load current (I ) typ. 40 ma o current active free > 0 ma O utput current active covered < 0...< 4 ma Load resistor R L = 0...00 Ohm Protective circuit 0...+60 C green/yellow/gree n built-i n of protection IEC 59 cable m x 0.4 mm brass PTFE All specifications are subject to change without notice. (05/004) 40 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP M18 x 1 : brass Non-flush mountable Sensing distance Sn = 8 mm With plastic flange connector M1 x 1 distance Sn [mm], flush mounting 8, no 8, no -pin DC 4-pin DC NO Antivalen t NPN IAS-0-A-A-Y 05 785 All specifications are subject to change without notice. (05/004) PNP IAS-10-A-S-Y IAS-10-A-A-Y 106 600 105 785 4 6 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma x 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 plastic flange connector M1 x 1 brass plastic flange connector M1 x 1 - - 1 4 5 6 brass RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 41

Series 60 - AC/DC M18 x 1 : brass Non-flush mountable Sensing distance Sn = 8 mm distance Sn [mm], flush Mounting 8, no 8, no -wire AC/DC -wire AC/DC NO IAS-60-A- S NC IAS-60-A- Ö 604 100 604 00 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma typ. 6 V residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.4 mm² brass 1 m x 0.4 mm² brass All specifications are subject to change without notice. (05/004) 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP M x 1.5 : Non-flush mountable Sensing distance Sn = 10 mm distance Sn [mm], flush mounting 10, no 10, no NPN -wire DC -wire DC NO NC All specifications are subject to change without notice. (05/004) PNP IAS-10--S-M IAS-10--Ö-M 116 900 117 000 4 5 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma khz khz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.4 mm m x 0.4 mm 1 4 5 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 4

Series 0 - NPN Ø = 0 mm : brass Flush mountable Sensing distance Sn = 10 mm distance Sn [mm], flush mounting 10, yes NPN -wire NO DC IAS-0-0-S 17 00 1 PNP voltage (U ) 10...5 V DC B current max. (I ) 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit 1 khz -5...+70 C yello w built-i n of protection IEC 59 cable m x 0.75 mm brass 1 4 5 6 All specifications are subject to change without notice. (05/004) 44 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP Series 0 - NPN M0 x 1.5 : brass Flush mountable Sensing distance Sn = 10 mm distance Sn [mm], flush mounting 10, yes 10, yes NPN -wire DC 4-wire DC NO IAS-0-A14- S Antivalen t IAS-0-A14- A 08 400 08 80 1 All specifications are subject to change without notice. (05/004) PNP IAS-10-A14- S IAS-10-A14- A 108 400 108 80 4 6 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma x 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n green/yello w built-i n of protection IEC 59 cable m x 0.75 mm brass PVC 1 4 5 6 m x 0.5 mm 4 brass PVC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 45

Series 10 - PNP Series 0 - NPN M0 x 1.5 : brass Flush mountable Sensing distance Sn = 10 mm With plastic flange connector M1 x 1 distance Sn [mm], flush mounting 10, yes 10, yes 10, yes -pin DC -pin DC 4-pin DC NO NC Antivalen t NPN IAS-0-A14-A-Y 08 85 PNP IAS-10-A14-S-Y IAS-10-A14-Ö-Y IAS-10-A14-A-Y 109 00 109 00 108 85 4 5 6 voltage (U ) 10...5 V DC 10...5 V DC 10...5 V DC B current max. (I ) 50 ma 50 ma x 50 ma e Load current min. - - - Voltage drop max. (U ) <.5 V <.5 V <.5 V d 10 % 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma typ. 15 ma 1 khz 1 khz 1 khz -5...+70 C -5...+70 C -5...+70 C yello w built-i n yello w built-i n green/yello w built-i n of protection IEC 59 plastic flange connector M1 x 1 brass PVC plastic flange connector M1 x 1 brass plastic flange connector M1 x 1 - - - PVC 1 4 5 6 brass PVC All specifications are subject to change without notice. (05/004) 46 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

With Analogue Series 10 - IL M0 x 1.5 : brass Flush mountable range 0...10 mm adjustable All specifications are subject to change without notice. (05/004) range [mm], flush mounting 0...10, yes Linear range [mm]...10 function analogue -wire DC analogue IAS-10-A14-I L 110 950 see below voltage (U ) 15...0 V DC B current max. (I ),5...> 0 ma e 5 % No-load current (I ) typ. 40 ma o current active free > 0 ma O utput current active covered < 0...< 4 ma Load resistor R L = 0...00 Ohm Protective circuit 0...+60 C green/yellow/gree n built-i n of protection IEC 59 cable m x 0.75 mm² brass PTFE RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 47

Series 60 - AC/DC M0 x 1.5 : brass Flush mountable Sensing distance Sn = 10 mm distance Sn [mm], flush Mounting 10, yes 10, yes -wire AC/DC -wire AC/DC NO IAS-60-A14 -S NC IAS-60-A14- Ö 607 00 607 500 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma typ. 6 V residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.75 mm² brass PVC 1 m x 0.75 mm² brass PVC All specifications are subject to change without notice. (05/004) 48 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Inducitve Sensors Series 0 - NPN Series 10 - PNP M0 x 1.5 : brass Non-flush mountable Sensing distance Sn = 15 mm distance Sn [mm], flush mounting 15, no 15, no NPN -wire DC 4-wire DC NO IAS-0-A4- S Antivalen t IAS-0-A4- A 11 000 10 980 1 All specifications are subject to change without notice. (05/004) PNP IAS-10-A4- S IAS-10-A4- A 111 000 110 980 4 6 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma x 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n green/yello w built-i n of protection IEC 59 cable m x 0.75 mm brass PVC 1 4 5 6 m x 0.5 mm 4 brass PVC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 49

Series 10 - PNP Series 0 - NPN M0 x 1.5 : brass Non-flush mountable Sensing distance Sn = 15 mm With plastic flange connector M1 x 1 distance Sn [mm], flush mounting 15, no 15, no -pin DC 4-pin DC NO Antivalen t NPN IAS-0-A4-A-Y 10 985 PNP IAS-10-A4-S-Y IAS-10-A4-A-Y 111 800 110 985 4 6 voltage (U ) 10...5 V DC 10...5 V DC B current max. (I ) 50 ma x 50 ma e Load current min. - - Voltage drop max. (U ) <.5 V <.5 V d 10 % 10 % No-load current (I ) typ. 15 ma o Protective circuit typ. 15 ma 1 khz 1 khz -5...+70 C -5...+70 C yello w built-i n green/yello w built-i n of protection IEC 59 plastic flange connector M1 x 1 brass PVC plastic flange connector M1 x 1 - - 1 4 5 6 brass PVC All specifications are subject to change without notice. (05/004) 50 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

With Analogue Series 10 - IL M0 x 1.5 : brass Non-flush mountable range 0...15 mm adjustable All specifications are subject to change without notice. (05/004) range [mm], flush mounting 0...15, no Linear range [mm] 5...15 function analogue -wire analogue DC IAS-10-A4-I L 11 550 see below voltage (U ) 15...0 V DC B current max. (I ),5...> 0m A e 5 % No-load current (I ) typ. 40 ma o current active free > 0 ma O utput current active covered < 0...< 4 ma Load resistor R L = 0...00 Ohm Protective circuit 0...+60 C green/yellow/gree n built-i n of protection IEC 59 cable m x 0.75 mm² brass PTFE RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 51

Series 60 - AC/DC M0 x 1.5 : brass Non-flush mountable Sensing distance Sn = 15 mm distance Sn [mm], flush Mounting 15, no 15, no -wire AC/DC -wire AC/DC NO IAS-60-A4- S NC IAS-60-A4- Ö 610 500 610 700 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ. typ. 9 ma 6 V typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.75 mm² brass PVC 1 m x 0.75 mm² brass PVC All specifications are subject to change without notice. (05/004) 5 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 10 - PNP Ø = 40 mm : Flush mountable Sensing distance Sn = 0 mm distance Sn [mm], flush mounting 0, yes NPN 4-wire DC Antivalen t All specifications are subject to change without notice. (05/004) PNP IAS-10-40-A 119 480 6 voltage (U ) 10...5 V DC B current max. (I ) x 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit 50 Hz -5...+70 C green/yello w built-i n of protection IEC 59 cable 1 4 5 6 m x 0.5 mm 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 5

Series 60 - AC/DC Ø = 40 mm : Flush mountable Sensing distance Sn = 0 mm distance Sn [mm], flush Mounting 0, yes 0, yes -wire AC/DC -wire AC/DC NO IAS-60-40-S NC IAS-60-40-Ö 60 900 61 100 1 voltage (U ) 0...50 V AC/DC 0...50 V AC/DC B Ourtput current max. (I ) 00 ma 00 ma e Minimum load typ. 9 ma Voltage drop max. (U ) typ. 6 V d typ. 9 ma typ. 6 V residual ripple max. - - No-load current (I ) typ..5 ma o Protective circuit typ..5 ma 5 Hz 5 Hz -5...+70 C -5...+70 C yello w built-i n yello w built-i n of protection IEC 59 cable m x 0.75 mm² 1 m x 0.75 mm² All specifications are subject to change without notice. (05/004) 54 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN Series 10 - PNP Ø = 50 mm : Non-flush mountable Sensing distance Sn = 5 mm distance Sn [mm], flush mounting 5, no NPN 4-wire DC Antivalen t IAS-0-51-A 19 880 All specifications are subject to change without notice. (05/004) PNP IAS-10-51-A 119 880 6 voltage (U ) 10...5 V DC B current max. (I ) x 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit 50 Hz -5...+70 C green/yello w built-i n of protection IEC 59 cable 1 4 5 6 m x 0.5 mm 4 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 55

Series 10 - PNP Ø = 64 mm : Non-flush mountable Sensing distance Sn = 40 mm distance Sn [mm], flush mounting 40, no NPN 4-wire DC Antivalen t PNP IAS-10-6-A 10 15 6 voltage (U ) 10...5 V DC B current max. (I ) x 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit 50 Hz -5...+70 C green/yello w built-i n of protection IEC 59 cable 1 4 5 6 m x 0.5 mm 4 All specifications are subject to change without notice. (05/004) 56 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

ATEX/StEx SERIES 10/0 I S ensing distance [mm] Diameter [mm] Material Version Pages T or with thread DC 10...0 V E M brass II 1 D T 101 C II G EEx m II T4 DMT 01 ATEX E 157 s tainless steel [VA] NPN [0], PNP [10] Selection NO [S] and Antivalent [A] see data sheets Flush Non-flus h 1 - M 1 x 1 - A1 [ VA] 10, 0 Cable 58 5 - M18 x 1 - A1 10 - M0 x 1,5 - A4 brass 10,0 Cable 59 brass 10, 0 Cable 60 All specifications are subject to change without notice. (07/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 57

Series 0 - NPN-StEx-ATEX Series 10 - PNP-StEx-ATEX DMT 01 ATEX E 157 distance Sn [mm], flush mounting M1 x 1 II 1/ D T 101 C For use in zone 0 II G EEx m II T4 : stainless steel VA Flush mountable Sensing distance Sn mm, yes NPN 4-wire NO DC IAS-0-A1-S-StE x IA 018 1 PNP IAS-10-A1-S-StE x IA 0111 4 voltage (U ) 10...0 V DC B current max. (I ) 150 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit khz -0...+90 C yello w built-i n of protection IEC 59 cable m x 0.14 mm 4 VA No. 1.405 PTFE PC 1 4 5 6 All specifications are subject to change without notice. (07/004) 58 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NPN-StEx-ATEX Series 10 - PNP-StEx-ATEX DMT 01 ATEX E 157 M18 x 1 II 1/ D T 101 C For use in zone 0 II G EEx m II T4 : brass Flush mountable Sensing distance Sn 5 mm distance Sn [mm], flush mounting 5, yes NPN 5-wire DC Antivalen t IAS-0-A1-A-StE x IA 016 All specifications are subject to change without notice. (05/004) PNP IAS-10-A1-A-StE x IA 0110 6 voltage (U ) 10...0 V DC B current max. (I ) x 00 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit khz -0...+90 C green/yello w built-i n of protection IEC 59 cable 1 4 5 6 m x 0.14 mm 5 brass PTFE PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 59

Series 0 - NPN-StEx-ATEX Series 10 - PNP-StEx-ATEX DMT 01 ATEX E 157 M0 x 1.5 II 1/ D T 101 C For use in zone 0 II G EEx m II T4 : brass Flush mountable Sensing distance Sn 10 mm distance Sn [mm], flush mounting 10, yes NPN 5-wire DC Antivalen t IAS-0-A14-A-StE x IA 017 PNP IAS-10-A14-A-StE x IA 0109 6 voltage (U ) 10...0 V DC B current max. (I ) x 00 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o Protective circuit 1 khz -0...+90 C green/yello w built-i n of protection IEC 59 cable 1 4 5 6 m x 0.4 mm 5 brass PTFE PC All specifications are subject to change without notice. (05/004) 60 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

ATEX AND ATEX/StEx SERIES 0 (NAMUR) I S ensing distance [mm] Diameter [mm] Version Pages T or with thread U i = 15 V DC NAMUR [0] E Brass [Ms] DMT 0 ATEX E 048 M Stainless steel [VA] Polyamide [] flush non-flus h 1 0. 8-4 VA 0 Cable 6 0. 8 - M5 x 0. 5 VA 0 Cable 6 1. 5-6. 5 VA 0 Cable 64 4 1. 5 - M8 x 1 VA 0 Cable 65 5-5 11 0 Cable 66 6 4 M1 x 1 - A1/A 7 5 8 M18 x 1 - A1/A 8 10 15 M0 x 1.5 - A14/A4 9 10 15 M x 1. 5 Brass Brass Brass Brass, 0, 0-StEx Cable 67-68 0, 0-StEx Cable 69-70 0, 0-StEx Cable 71-7 0, 0-StEx Cable 7-74 All specifications are subject to change without notice. (07/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 61

Series 0 - NAMUR DMT 0 ATEX E 048 distance Sn [mm], flush mounting Ø 4 mm II G EEx ia IIC T1-T6 For use in areas where there is a risk of explosion : stainless steel VA Flush mountable Sensing distance Sn = 0.8 mm 0.8, yes -wire DC NAMUR DIN 60947-5-6 IAS-0-04-N 00 700 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 500 Hz -5...+70 C - of protection IEC 59 cable m x 0.14 mm VA No. 1.405 - - All specifications are subject to change without notice. (07/004) 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR DMT 0 ATEX E 048 distance Sn [mm], flush mounting M5 x 0.5 II G EEx ia IIC T1-T6 For use in areas where there is a risk of explosion : stainless steel VA Flush mountable Sensing distance Sn = 0.8 mm 0.8, yes -wire DC NAMUR DIN 60947-5-6 IAS-0-M5-N 00 800 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 500 Hz -5...+70 C - All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.14 mm VA No. 1.405 - RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 6

Serie 0 - NAMUR DMT 0 ATEX E 048 distance Sn [mm], flush mounting Ø 6.5 mm II G EEx ia IIC T1-T6 For use in areas where there is a risk of explosion : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm 1.5, yes -wire DC NAMUR DIN 60947-5-6 IAS-0-6.5- N 00 900 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 500 Hz -5...+70 C - of protection IEC 59 cable m x 0.14 mm VA No. 1.405 PVC PC All specifications are subject to change without notice. (08/004) 64 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR : DMT 0 ATEX E 048 distance Sn [mm], flush mounting M8 x 1 II G EEx ia IIC T1-T6 For use in areas where there is a risk of explosion : stainless steel VA Flush mountable Sensing distance Sn = 1.5 mm 1.5, yes -wire DC NAMUR DIN 60947-5-6 IAS-0-M8-N 01 000 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 500 Hz -5...+70 C - All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.14 mm VA No. 1.405 PVC PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 65

Series 0 - NAMUR DMT 0 ATEX E 048 distance Sn [mm], flush mounting Ø 11 mm II G EEx ia IIC T1-T6 For use in areas where there is a risk of explosion : Non-flush mountable Sensing distance Sn = 5 mm 5, no -wire DC NAMUR DIN 60947-5-6 IAS-0-14-N 01 500 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1 khz -5...+70 C yello w of protection IEC 59 cable m x 0.14 mm All specifications are subject to change without notice. (07/004) 66 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M1 x 1 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion Flush mountable Sensing distance Sn = mm, yes -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A1- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A1-N-StE x Ex II 1 D T 00 100 IA 0091 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1.5 khz -5...+70 C -0...+90 C yello w 101 C All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.14 mm brass No. 1 No. m x 0.14 mm PTFE PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 67

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M1 x1 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Non-flush mountable Sensing distance Sn = 4 mm 4, no -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A-N-StE x Ex II 1 D T 00 00 IA 0090 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1.5 khz -5...+70 C -0...+90 C yello w 101 C of protection IEC 59 cable m x 0.14 mm brass No. 1 No. m x 0.14 mm PTFE PC All specifications are subject to change without notice. (08/004) 68 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M18 x 1 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Flush mountable Sensing distance Sn = 5 mm 5, yes -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A1- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A1-N-StE x Ex II 1 D T 00 00 IA 009 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1.5 khz -5...+70 C -0...+90 C yello w 101 C All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.4 mm brass No. 1 No. m x 0.4 mm PTFE PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 69

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M18 x 1 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Non-flush mountable Sensing distance Sn = 8 mm 8, no -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A-N-StE x Ex II 1 D T 00 400 IA 0094 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1.5 khz -5...+70 C -0...+90 C yello w 101 C of protection IEC 59 cable m x 0.4 mm brass No. 1 No. m x 0.4 mm PTFE PC All specifications are subject to change without notice. (08/004) 70 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M0 x 1.5 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Flush mountable Sensing distance Sn = 10 mm 10, yes -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A14- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A14-N-StE x Ex II 1 D T 00 500 IA 0095 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1 khz -5...+70 C -0...+90 C yello w 101 C All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.75 mm PVC brass No. 1 No. m x 0.75 mm PTFE PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 71

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M 0 x 1.5 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Non-flush mountable Sensing distance Sn = 15 mm 15, no -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-A4- N Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-A4-N-StE x Ex II 1 D T 00 600 IA 0096 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1 khz -5...+70 C -0...+90 C yello w 101 C of protection IEC 59 cable m x 0.75 mm PVC brass No. 1 No. m x 0.75 mm PTFE PC All specifications are subject to change without notice. (08/004) 7 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Series 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M x 1.5 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : brass Flush mountable Sensing distance Sn = 10 mm 10, yes -wire DC -wire DC NAMUR DIN 60947-5-6 IAS-0-0-N-M Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-0-N-M-StE x Ex II 1 D T 0 400 IA 0097 1 voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1 khz -5...+70 C -0...+90 C yello w 101 C All specifications are subject to change without notice. (08/004) of protection IEC 59 cable m x 0.75 mm PVC PVC brass No. 1 No. m x 0.75 mm PTFE PC RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 7

Serie 0 - NAMUR DMT 0 ATEX E 048 DMT 01 ATEX E 157 distance Sn [mm], flush mounting M x 1.5 II G EEx ia IIC T1-T6 II 1 D T 101 C For use in areas where there is a risk of explosion : Non-flush mountable Sensing distance Sn = 15 mm 15, no -wire DC NAMUR DIN 60947-5-6 IAS-0-5-N-M Application/Marking Ex II G EEx ia IIC T1-T6 IAS-0-5-N-M-StE x Ex II 1 D T 0 800 IA 0098 see below voltage (U ) U = 15 V DC B i current active free current active covered Self-inductance (L) Self-capacitance (C) > typ. ma < typ. 1.5 ma mh 50 nf 5 % 1 khz -5...+70 C -0...+90 C yello w 101 C of protection IEC 59 cable m x 0.75 mm PC All specifications are subject to change without notice. (08/004) 74 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

INDUCTIVE HIGH-TEMPERATURE SENSORS I S ensing distance Sn [mm] Diameter [mm] Version Amplifie r Pages T or with thread 10...5 V DC Cable E M o r A luminium [AL] NPN [0]; PNP[10] r ectangular housing Stainless steel [VA] Polyetheretherketone [PEEK] metal flange connector sensor [Y] metal flange connector Amplifier [Y5] flush non-flus h 1-4 M1 x 1 PEEK Sensor IS Cable 76-8 M18 x 1 PEEK Sensor IS Cable 77-1 M x 1. 5 4-15 M0 x 1. 5 5-0 M x 1. 5 PEEK PEEK PEEK, PEEK/VA Sensor IS Y 78 Sensor IS Y 79 Sensor IS Y 80-81 6-5 40 x 40 x 56 PEEK/AL 7-5 40 x 40 x 56 PEEK/AL Sensor IS Y 8 Sensor IS Y 8 Amplifier ISA 8 - - 98,5 x 64 x 4, 5 AL 10 Y5 84 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 75

Inductive High-Temperature Sensors Series - 50 M1 x 1 with sealing screw For connection to the evaluation unit ISA-...-Y5 : PEEK For an of max. 50 C Techincal data distance Sn [mm] 4 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M1 IA 0117-70...+50 C Enclosure rating IEC 59 IP 68 cable for connection to inductive evaluation units ISA-... with plug-in connector m PTFE with VA screen grid lead PEEK PEEK All specifications are subject to change without notice. (05/004) 76 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Inductive High-Temperature Sensors Series - 50 M18 x 1 with sealing screw For connection to the evaluation unit ISA-...-Y5 : PEEK For an of max. 50 C Techincal data distance Sn [mm] 8 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M18 IA 0118-70...+50 C Enclosure rating IEC 59 IP 68 cable for connection to inductive evaluation units ISA-... with plug-in connector m PTFE with VA screen grid lead PEEK PEEK Available also with 5 m connection cable: IA 017 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 77

Inductive High-Temperature Sensors Series - 50 M x 1.5 For connection to the evaluation unit ISA-...-Y5 : PEEK/Brass For an of max. 50 C Techincal data distance Sn [mm] 1 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M-Y IA 0119-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK/Brass PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 All specifications are subject to change without notice. (05/004) 78 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Inductive High-Temperature Sensors Series - 50 M0 x 1.5 For connection to the evaluation unit ISA-...-Y5 : PEEK/Brass For an of max. 50 C Techincal data distance Sn [mm] 15 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M0-Y IA 010-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK/Brass PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 0 m PTFE-cable with VA screen grid lead and connectors Art. No. 1915 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 79

Inductive High-Temperature Sensors Series - 50 M x 1.5 For connection to the evaluation unit ISA-...-Y5 : PEEK For an of max. 50 C Techincal data distance Sn [mm] 0 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M-Y IA 01-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 0 m PTFE-cable with VA screen grid lead and connectors Art. No. 1915 All specifications are subject to change without notice. (05/004) 80 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Inductive High-Temperature Sensors Series - 50 M x 1.5 For connection to the evaluation unit ISA-...-Y5 : PEEK/VA For an of max. 50 C Techincal data distance Sn [mm] 0 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-M-PEEK/VA- Y IA 014-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK/VA No. 1.405 PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 0 m PTFE-cable with VA screen grid lead and connectors Art. No. 1915 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 81

Inductive High-Temperature Sensors Series - 50 40 x 40 x 56 mm For connection to the evaluation unit ISA-...-Y5 : PEEK/AL For an of max. 50 C Techincal data distance Sn [mm] 5 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-C5-Y IA 0115-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK/AL PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 0 m PTFE-cable with VA screen grid lead and connectors Art. No. 1915 All specifications are subject to change without notice. (05/004) 8 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

Inductive High-Temperature Sensors Series - 50 55 x 55 x 56 mm For connection to the evaluation unit ISA-...-Y5 : PEEK/AL For an of max. 50 C Techincal data distance Sn [mm] 5 Sensing distance adjustable at the evaluation unit - Mounting: flush/ non-flush non-flus h IS-50-C5-Y IA 011-70...+50 C Enclosure rating IEC 59 for inductive evaluation units ISA-... metal flange connecto r PEEK/AL PEEK cable is not delivered with the probe (see page 86). Order specifications: m PTFE-cable with VA screen grid lead and connectors Art. No. 191 5 m PTFE-cable with VA screen grid lead and connectors Art. No. 191 10 m PTFE-cable with VA screen grid lead and connectors Art. No. 1914 0 m PTFE-cable with VA screen grid lead and connectors Art. No. 1915 All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 8

Evaluation Unit For Inductive High-Temperature Sensors Series - 50 PNP 98.5 x 64 x 4.5 mm For connection to inductive high-temperature sensors IS-50-... : AL distance Sn [mm], flush Mounting - O utput 4-pin DC antivalen t PNP ISA-10-50-A-Y5-M1 ISA-10-50-A-Y5-M1 8 ISA-10-50-A-Y5-M IA 01 IA 01 IA 011 6 6 6 PNP ISA-10-50-A-Y5-M0/M ISA-10-50-A-Y5-C 5 ISA-10-50-A-Y5-C 5 IA 010 IA 0114 IA 019 6 6 6 voltage (U ) 10...5 V DC B current max. (I ) x 50 ma e Load current min. - Voltage drop max. (U ) <.5 V d 10 % No-load current (I ) typ. 15 ma o 50 Hz -5...+70 C - Protective circuit built-i n of protection IEC 59 metal flange connector M1 x 1 - - AL 1 4 5 6 All specifications are subject to change without notice. (09/004) 84 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

FEMALE CONNECTORS Sensor F emale Connector Article-No. LED IP Connectio n Cable- Sensor Version T ype N o. Fig. pnp 5 19100 npn 6 19150 green/ yellow + 65 length + length [ mm ] [ m] [ mm] Connecto r x 0.5/Pg 7 clampable - 6 Y, Y5 pnp/npn 9 191500-67 4 x 0.75/Pg 9 clampable - 8 Y, Y5 AC/DC 9a 191550-67 4 x 0.75/Pg 9 clampable - 8 Y1 pnp/npn 16 191900-67 x 0.4, 5 17 Y, Y5 pnp/npn 18 19000-67 x 0.4 5 5 Y, Y5 pnp 1 19150 npn 1900 + 67 x 0.4 5 18 Y, Y5 pnp/npn 6 19900-67 4 x 0.5 5 1 Y, Y5 antivalent All specifications are subject to change without notice. (05/004) pnp/npn 8 19000-67 4 x 0.5 5 17 Y, Y5 antivalent pnp/npn 45 1910-67 x 0.5 5 9 Y7, Y8 pnp 46 190 + pnp/npn 47 190 - pnp/npn pnp/npn AC/DC 67 x 0.5 5 1 Y7, Y8 49a 1945-68 5 x 0.5 0 Y10 50 1950-67 5 x 0.5 18 Y1, Y9 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 85

MOUNTING BLOCKS Dimension: A rt.-no. Block No. Ø Sensor [mm] a b c d Ø e Ø f g Ø h Nuts 190150 11 10 0 0 10 0 4, 8 4, 5 10 M4 19000 1 11 0 0 10 0 4, 8 4, 5 11 M4 19050 1 0 45 0 15 0 5, 9 6 0 M5 19000 14 45 0 15 0 5, 9 6 M5 19050 15 0 60 45 15 45 5, 9 6 0 M5 190400 16 60 45 15 45 5, 9 6 M5 190450 17 4 60 45 15 45 5, 9 6 4 M5 19000 18 40 80 65 15 65 5, 9 6 40 M5 190050 19 50 80 65 15 65 5, 9 6 50 M5 190100 140 64 95 80 15 80 5, 9 6 64 M5 FEMALE CONNECTOR, SCREENED Dimensions "a" to "h" in mm cable For inductive high-temperature sensors with Lemoconnector and screened cable m 191 5 m 191 10 m 1914 0 m 1915 All specifications are subject to change without notice. (05/004) 86 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

PROTECTION CAPS AND PROTECTION SETS Example: Protection Caps M0/M PTFE PROTECTION CAP The PTFE protection cap (PEEK and Delrin are also available) is designed for applications where the detected is highly abrasive, e.g. granules. It is a protection cap for the front cap of the sensor. In the case of damage due to abrasion one only has to change the protection cap and the sensor remains in good condition. Dimension: Protection Cap M0 PTFE 75000450 PEEK 75000460 Delrin 75000470 Dimension: Protection Cap M PTFE 75000400 PEEK 75000410 Delrin 7500040 All specifications are subject to change without notice. (05/004) Example: Protection Set M Protection Set M18 19605 Protection Set M0 1960 Protection Set M 19601 PROTECTION SET The PTFE protection set M x 1.5 consists of an internally threaded cover, a Pg9-screwing for cable entry and a rubber gasket between the cover and the sensor. This protection cover serves as improvement to the degree of protection, against infiltration of liquids, for example in applications where the sensor is totally immersed in liquids. The resistance of the still needs to be checked. The thread of the sensor has to be sealed, for example with PTFE sealing- tape. The protection cover has to be screwed totally up to the end, and then the Pg-screw has to be fixed. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 87

NORMS The products of Rechner Industrie-Elektronik GmbH are designed and checked in accordance with the standards and specifications, DIN - VDE - IEC, for electric and electronic instruments. For new and revised products the newest standards are always used. Effective standards for proximity switches and sensors: DIN VDE 0660 Part 08: Low-voltage switchgear - additional requirements for inductive proximity switches. DIN VDE 0660 Part 09 Low-voltage switchgear and controlgear, control switches - additional requirements for proximity switches used in safety-related applications. DIN VDE 0660 Part 1 (Replaces DIN 194) Istrumentation and control technology - electrical position sensors - DC interface for position sensors and switching amplifiers European Standards EN 60947-5- Low Voltage Switchgear Part 5 Control circuit devices and switching elements, section : proximity switches EN 60947-5-6 Control circuit devices and switching elements, proximity sensors - DC interface for proximity sensors and switching amplifiers (NAMUR) International Standards IEC 947-5- Low-voltage switchgear and controlgear Part 5 Control circuit devices and switching elements - Section, proximity switches Draft IEC 6194 Control circuit devices and switching elements DC interface for proximity sensors and switching amplifiers (NAMUR) Standards On Explosion Protection DIN EN 50014 apparatus for potentially explosive environments. General requirements. DIN EN 5000 apparatus for potentially explosive environments. Intrinsic safety i EN 60079-10 apparatus for potentially explosive environments. Classification of hazardous areas. EN 60079-14 apparatus for potentially explosive environments. Classification of hazardous areas (mines excepted). All specifications are subject to change without notice. (05/004) 88 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

NORMS Norms for quality assurance (QS) DIN ISO 9000-9004 (EN 9000-9 004) Quality assurance (QA) for products and services DIN ISO 9001 Quality assurance in design/development, production, installation and servicing DIN ISO 900 Quality assurance in production DIN ISO 900 Quality assurance for final testing only DIN ISO 9004 Quality management and elements of a quality management system RECHNER Industrie-Elektronik-GmbH is certified according to DIN ISO 9001:000. - Marking The CE marking represents the manufacturer s confirmation that the identified product conforms to applicable standards and directives throughout Europe. The following regulations apply to the RECHNER products. 89/6/EWG EMC Directive (EN 60 947-5-) 7//EWG Low-voltage Directive (compare with VDE 0160, product standard EN 60947-5-) Directive 94/9/EG Equipment and Protection Systems designed for use in potentially explosive environments All specifications are subject to change without notice. (07/004) RECHNER Industrie-Elektronik GmbH certifies the conformity of its products with each of the applicable directives in a Manufacturer s Declaration. In addition RECHNER has a laboratory accredited by DATech for testings according to IEC/EN 60947-5- and also an accredited EMC laboratory. RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 89

SPECIFICATION FOR EXPLOSION PROTECTION Division of Hazards Ignition Hazards due to Sparks European Union Explosive mixtures in Group1: mines susceptible to fire damp Group: areas other than mines Classification of the protection types intrinsic safety/ flame-proof enclosure according to minimum ignition current/limit gap with reference to the minimum ignition energy of representative gases: Group I Methane Group IIA Propane Group IIB Ethylene Group IIC Hydrogen, Acetylene This classification also partially applies to the type of protection n (zone equipment) North America Explosive mixtures of air with CLASS I: Gases and vapours CLASS II: Dust CLASS III: Fibers Division of CLASS according to ignition energy: CLASS I Group A Acetylene B Hydrogen C Ethylene D Methane CLASS II Group E Metal dust F Coal dust G Grain dust CLASS III No grouping Ignition Hazards due to Hot Surfaces Classification into temperature according to IEC 79-8 for maximum temperatures at an ambient temperature of 40 C under failure conditions: T1 < 450 C T < 00 C T < 00 C T4 < 15 C T5 < 100 C T6 < 85 C The following are classified according to the probability of the occurrence of an explosive atmosphere: Division of Hazardous Areas For gases, fumes and vapours: (EN 60079-10) for gases and dusts Zone 0 constant or long term 1 occasional Division 1 } rare and short term } Division for dusts: (EN 117-1) Zone 0 constant or long term or frequent 1 occasional short term or accumulation or layers of dust Note (see IEC 79-10): constant or long term > 1000 h/year, occasionally represents 10 1000 h/year, rare or short term < 10h/year Safety data Certification Authorities Installation Requirements For the ratings of combustible gases and vapours as a basis for classification according to ignition energy, ignition temperature and flash point, see: Redeker, Nabert, Schön/Safety Ratings of Combustible Gases and Vapours PTB BVS BASEEFA Physikalisch-Technische Bundesanstalt Bergbauversuchsstrecke British Approvals Service for Equipment in Flammable Atmosphere and others DIN EN 60079-14 (VDE 0165 Part 1) for explosive gas environments DIN EN 5081-1- (VDE 0165 Part ) for environments with flammable dust NF 497 M CSA Nr. C-1 UL FM CSA NF 70 NF 49 Underwriters Laboratories, USA Factory Mutual Research, USA Canadian Standards Association National Code Art. 500 Standard for Intrinsically safe operations... All specifications are subject to change without notice. (05/004) 90 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TYPE SELECTION IN ARTICLE NUMBER ORDER Description Page Description Page All specifications are subject to change without notice. (05/004) 100110 IAS-10-M8-S 10000 IAS-10-M8-S-Y7 4 10000 IAS-10-M8-Ö 10010 IAS-10-M8-Ö-Y7 4 100500 IAS-10-A11-S 101010 IAS-10-A11-Ö 10100 IAS-10-A1-S 5 10150 IAS-10-A1-Ö 5 101700 IAS-10-A1-S 7 101900 IAS-10-A1-Ö 7 1000 IAS-10-A1-S-Y5 8 1050 IAS-10-A1-Ö-Y5 8 10400 IAS-10-A-S 0 10500 IAS-10-A-Ö 0 10001 IAS-10-A-S-Y5 1 10050 IAS-10-A-Ö-Y5 1 10060 IAS-10-A1-A 4 10068 IAS-10-A1-A-Y5 6 10100 IAS-10-A1-S 4 1000 IAS-10-A1-Ö 4 105750 IAS-10-A1-IL 5 105751 IAS-10-A1-IL-Y 7 105780 IAS-10-A-A 9 105785 IAS-10-A-A-Y 4 1 105800 IAS-10-A-S 9 106600 IAS-10-A-S-Y 4 1 10850 IAS-10-A-IL 4 0 10880 IAS-10-A14-A 4 5 10885 IAS-10-A14-A-Y 4 6 108400 IAS-10-A14-S 4 5 10900 IAS-10-A14-S-Y 4 6 10900 IAS-10-A14-Ö-Y 4 6 110950 IAS-10-A14-IL 4 7 110980 IAS-10-A4-A 4 9 110985 IAS-10-A4-A-Y 5 0 111000 IAS-10-A4-S 4 9 111800 IAS-10-A4-S-Y 5 0 11550 IAS-10-A4-IL 5 1 11610 IAS-10-04-S 1 6 11650 IAS-10-04-Ö 1 6 114010 IAS-10-M5-S 1 7 114110 IAS-10-M5-Ö 1 7 114400 IAS-10-M5-S-Y7 1 8 114450 IAS-10-M5-Ö-Y7 1 8 114500 IAS-10-6.5/15-S 1 9 114510 IAS-10-6.5-S-LED 0 114610 IAS-10-6.5-Ö-LED 0 114650 IAS-10-6.5/15-Ö 1 9 114900 IAS-10-6.5-S-Y7 1 115000 IAS-10-6.5-Ö-Y7 1 11500 IAS-10-14-S 6 11550 IAS-10-14-Ö 6 116900 IAS-10--S-M 4 117000 IAS-10--Ö-M 4 119480 IAS-10-40-A 5 119880 IAS-10-51-A 5 5 1015 IAS-10-6-A 5 6 19000 Mounting block No. 18 40D, 8 6 190050 Mounting block No. 19 50D, 8 6 190100 Mounting block No. 140 64D, 8 6 190150 Mounting block No. 11 10D, 8 6 19000 Mounting block No. 1 11D, 8 6 19050 Mounting block No. 1 0D, 8 6 19000 Mounting block No. 14 D, 8 6 19050 Mounting block No. 15 0D, 8 6 190400 Mounting block No. 16 D, 8 6 190450 Mounting block No. 17 4D, 8 6 19100 Female connector No. 5, angled 8 5 19150 Female connector No. 6, angled 8 5 191500 Female connector No. 9, angled 8 5 191550 Female connector No. 9A, angled 8 5 191900 Female connector No. 16, angled 8 5 19000 Female connector No. 18, straight 8 5 19150 Female connector No. 1, angled 8 5 1900 Female connector No., angled 8 5 19900 Female connector No. 6, straight 8 5 19000 Female connector No. 8, angled 8 5 1910 Female connector No. 45, straight 8 5 190 Female connector No. 46, angled 8 5 190 Female connector No. 47, angled 8 5 191 Female connector IS-HT, m, screened 8 6 191 Female connector IS-HT, 5 m, screened 8 6 1914 Female connector IS-HT, 10 m, screened 8 6 1915 Female connector IS-HT, 0 m, screened 8 6 1945 Female connector No. 49a, angled 8 5 1950 Female connector No. 50, angled 8 5 19601 Protection set M/PTFE 8 7 1960 Protection set M0/PTFE 8 7 19605 Protection set M18/PTFE 8 7 00500 IAS-0-A11-S 0100 IAS-0-A1-S 5 01700 IAS-0-A1-S 7 01900 IAS-0-A1-Ö 7 000 IAS-0-A1-S-Y5 8 0400 IAS-0-A-S 0 0500 IAS-0-A-Ö 0 0050 IAS-0-A-Ö-Y5 1 0060 IAS-0-A1-A 4 0067 IAS-0-A1-A-Y5 6 0100 IAS-0-A1-S 4 05780 IAS-0-A-A 9 05785 IAS-0-A-A-Y 4 1 05800 IAS-0-A-S 9 0880 IAS-0-A14-A 4 5 0885 IAS-0-A14-A-Y 4 6 08400 IAS-0-A14-S 4 5 10980 IAS-0-A4-A 4 9 10985 IAS-0-A4-A-Y 5 0 11000 IAS-0-A4-S 4 9 1610 IAS-0-04-S 1 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 91

TYPE SELECTION IN ARTICLE NUMBER ORDER Description Page Description Page 1650 IAS-0-04-Ö 1 6 14010 IAS-0-M5-S 1 7 14110 IAS-0-M5-Ö 1 7 14500 IAS-0-6.5/15-S 1 9 1700 IAS-0-0-S 4 4 19880 IAS-0-51-A 5 5 00100 IAS-0-A1-N, ATEX 6 7 0000 IAS-0-A-N, ATEX 6 8 0000 IAS-0-A1-N, ATEX 6 9 00400 IAS-0-A-N, ATEX 7 0 00500 IAS-0-A14-N, ATEX 7 1 00600 IAS-0-A4-N, ATEX 7 00700 IAS-0-04-N 6 00800 IAS-0-M5-N 6 00900 IAS-0-6.5-N 6 4 01000 IAS-0-M8-N 6 5 01500 IAS-0-14-N, ATEX 6 6 0400 IAS-0-0-N-M, ATEX 7 0800 IAS-0-5-N-M, ATEX 7 4 60000 IAS-60-A1-S 9 600500 IAS-60-A1-Ö 9 600700 IAS-60-A-S 600900 IAS-60-A-Ö 601000 IAS-60-A1-S 8 60100 IAS-60-A1-Ö 8 604100 IAS-60-A-S 4 60400 IAS-60-A-Ö 4 60700 IAS-60-A14-S 4 8 607500 IAS-60-A14-Ö 4 8 610500 IAS-60-A4-S 5 610700 IAS-60-A4-Ö 5 614900 IAS-60-14-S-M1 60900 IAS-60-40-S 5 4 61100 IAS-60-40-Ö 5 4 75000400 Protection cap M PTFE 8 7 75000410 Protection cap M PEEK 8 7 7500040 Protection cap M Delrin 8 7 75000450 Protection cap M0 PTFE 8 7 75000460 Protection cap M0 PEEK 8 7 75000470 Protection cap M0 Delrin 8 7 IA0090 IAS-0-A-N-StEx, ATEX 6 8 IA0091 IAS-0-A1-N-StEx, ATEX 6 7 IA009 IAS-0-A1-N-StEx, ATEX 6 9 IA0094 IAS-0-A-N-StEx, ATEX 7 0 IA0095 IAS-0-A14-N-StEx, ATEX 7 1 IA0096 IAS-0-A4-N-StEx, ATEX 7 IA0097 IAS-0-0-N-M-StEx, ATEX 7 IA0098 IAS-0-5-N-M-StEx, ATEX 7 4 IA0109 IAS-10-A14-A-StEx 6 0 IA0110 IAS-10-A1-A-StEx 5 9 IA0111 IAS-10-A1-S-StEx 5 8 IA0114 ISA-10-50-A-Y5-C5 8 4 IA0115 IS-50-C5-Y 8 IA0117 IS-50-M1 7 6 IA0118 IS-50-M18 7 7 IA0119 IS-50-M-Y 7 8 IA010 IS-50-M0-Y 7 9 IA011 IS-50-C5-Y 8 IA01 IS-50-M-Y 8 0 IA014 IS-50-M-PEEK/VA-Y 8 1 IA017 IS-50-M18, 5 m 7 7 IA019 ISA-10-50-A-Y5-C5 8 4 IA010 ISA-10-50-A-Y5-M0/M 8 4 IA011 ISA-10-50-A-Y5-M 8 4 IA01 ISA-10-50-A-Y5-M18 8 4 IA01 ISA-10-50-A-Y5-M1 8 4 IA016 IAS-0-A1-A-StEx 5 9 IA017 IAS-0-A14-A-StEx 6 0 IA018 IAS-0-A1-S-StEx 5 8 All specifications are subject to change without notice. (05/004) 9 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

TYPE SELECTION IN TYPE DESCRIPTION ORDER Description Page Description Page All specifications are subject to change without notice. (05/004) Female connector IS-HT, m, screened 191 8 6 Female connector IS-HT, 5 m, screened 191 8 6 Female connector IS-HT, 10 m, screened 1914 8 6 Female connector IS-HT, 0 m, screened 1915 8 6 Female connector No. 5, angled 19100 8 5 Female connector No. 6, angled 19150 8 5 Female connector No. 9, angled 191500 8 5 Female connector No. 9A, angled 191550 8 5 Female connector No. 16, angled 191900 8 5 Female connector No. 18, straight 19000 8 5 Female connector No. 1, angled 19150 8 5 Female connector No., angled 1900 8 5 Female connector No. 6, straight 19900 8 5 Female connector No. 8, angled 19000 8 5 Female connector No. 45, straight 1910 8 5 Female connector No. 46, angled 190 8 5 Female connector No. 47, angled 190 8 5 Female connector No. 49a, angled 1945 8 5 Female connector No. 50, angled 1950 8 5 IAS-10-04-Ö 11650 1 6 IAS-10-04-S 11610 1 6 IAS-10-14-Ö 11550 6 IAS-10-14-S 11500 6 IAS-10--Ö-M 117000 4 IAS-10--S-M 116900 4 IAS-10-40-A 119480 5 IAS-10-51-A 119880 5 5 IAS-10-6.5/15-Ö 114650 1 9 IAS-10-6.5/15-S 114500 1 9 IAS-10-6.5-Ö-LED 114610 0 IAS-10-6.5-Ö-Y7 115000 1 IAS-10-6.5-S-LED 114510 0 IAS-10-6.5-S-Y7 114900 1 IAS-10-6-A 1015 5 6 IAS-10-A11-Ö 101010 IAS-10-A11-S 100500 IAS-10-A1-Ö 101900 7 IAS-10-A1-Ö-Y5 1050 8 IAS-10-A1-S 101700 7 IAS-10-A1-S-StEx IA0111 5 8 IAS-10-A1-S-Y5 1000 8 IAS-10-A1-A 10060 4 IAS-10-A1-A-StEx IA0110 5 9 IAS-10-A1-A-Y5 10068 6 IAS-10-A1-IL 105750 5 IAS-10-A1-IL-Y 105751 7 IAS-10-A1-Ö 1000 4 IAS-10-A1-S 10100 4 IAS-10-A14-A 10880 4 5 IAS-10-A14-A-StEx IA0109 6 0 IAS-10-A14-A-Y 10885 4 6 IAS-10-A14-IL 110950 4 7 IAS-10-A14-Ö-Y 10900 4 6 IAS-10-A14-S 108400 4 5 IAS-10-A14-S-Y 10900 4 6 IAS-10-A1-Ö 10150 5 IAS-10-A1-S 10100 5 IAS-10-A-Ö 10500 0 IAS-10-A-Ö-Y5 10050 1 IAS-10-A-S 10400 0 IAS-10-A-S-Y5 10001 1 IAS-10-A-A 105780 9 IAS-10-A-A-Y 105785 4 1 IAS-10-A-IL 10850 4 0 IAS-10-A-S 105800 9 IAS-10-A-S-Y 106600 4 1 IAS-10-A4-A 110980 4 9 IAS-10-A4-A-Y 110985 5 0 IAS-10-A4-IL 11550 5 1 IAS-10-A4-S 111000 4 9 IAS-10-A4-S-Y 111800 5 0 IAS-10-M5-Ö 114110 1 7 IAS-10-M5-Ö-Y7 114450 1 8 IAS-10-M5-S 114010 1 7 IAS-10-M5-S-Y7 114400 1 8 IAS-10-M8-Ö 10000 IAS-10-M8-Ö-Y7 10010 4 IAS-10-M8-S 100110 IAS-10-M8-S-Y7 10000 4 IAS-0-04-Ö 1650 1 6 IAS-0-04-S 1610 1 6 IAS-0-0-S 1700 4 4 IAS-0-51-A 19880 5 5 IAS-0-6.5/15-S 14500 1 9 IAS-0-A11-S 00500 IAS-0-A1-Ö 01900 7 IAS-0-A1-S 01700 7 IAS-0-A1-S-StEx IA018 5 8 IAS-0-A1-S-Y5 000 8 IAS-0-A1-A 0060 4 IAS-0-A1-A-StEx IA016 5 9 IAS-0-A1-A-Y5 0067 6 IAS-0-A1-S 0100 4 IAS-0-A14-A 0880 4 5 IAS-0-A14-A-StEx IA017 6 0 IAS-0-A14-A-Y 0885 4 6 IAS-0-A14-S 08400 4 5 IAS-0-A1-S 0100 5 IAS-0-A-Ö 0500 0 IAS-0-A-Ö-Y5 0050 1 IAS-0-A-S 0400 0 IAS-0-A-A 05780 9 IAS-0-A-A-Y 05785 4 1 IAS-0-A-S 05800 9 IAS-0-A4-A 10980 4 9 IAS-0-A4-A-Y 10985 5 0 IAS-0-A4-S 11000 4 9 IAS-0-M5-Ö 14110 1 7 IAS-0-M5-S 14010 1 7 IAS-0-04-N 00700 6 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 9

TYPE SELECTION IN TYPE DESCRIPTION ORDER Description Page Description Page IAS-0-14-N, ATEX 01500 6 6 IAS-0-0-N-M, ATEX 0400 7 IAS-0-0-N-M-StEx, ATEX IA0097 7 IAS-0-5-N-M, ATEX 0800 7 4 IAS-0-5-N-M-StEx, ATEX IA0098 7 4 IAS-0-6.5-N 00900 6 4 IAS-0-A1-N, ATEX 00100 6 7 IAS-0-A1-N-StEx, ATEX IA0091 6 7 IAS-0-A1-N, ATEX 0000 6 9 IAS-0-A1-N-StEx, ATEX IA009 6 9 IAS-0-A14-N, ATEX 00500 7 1 IAS-0-A14-N-StEx, ATEX IA0095 7 1 IAS-0-A-N, ATEX 0000 6 8 IAS-0-A-N-StEx, ATEX IA0090 6 8 IAS-0-A-N, ATEX 00400 7 0 IAS-0-A-N-StEx, ATEX IA0094 7 0 IAS-0-A4-N, ATEX 00600 7 IAS-0-A4-N-StEx, ATEX IA0096 7 IAS-0-M5-N 00800 6 IAS-0-M8-N 01000 6 5 IAS-60-14-S-M1 614900 IAS-60-40-Ö 61100 5 4 IAS-60-40-S 60900 5 4 IAS-60-A1-Ö 600500 9 IAS-60-A1-S 60000 9 IAS-60-A1-Ö 60100 8 IAS-60-A1-S 601000 8 IAS-60-A14-Ö 607500 4 8 IAS-60-A14-S 60700 4 8 IAS-60-A-Ö 600900 IAS-60-A-S 600700 IAS-60-A-Ö 60400 4 IAS-60-A-S 604100 4 IAS-60-A4-Ö 610700 5 IAS-60-A4-S 610500 5 IS-50-C5-Y IA0115 8 IS-50-C5-Y IA011 8 IS-50-M1 IA0117 7 6 IS-50-M18 IA0118 7 7 IS-50-M18, 5 m IA017 7 7 IS-50-M-Y IA0119 7 8 IS-50-M0-Y IA010 7 9 IS-50-M-PEEK/VA-Y IA014 8 1 IS-50-M-Y IA01 8 0 ISA-10-50-A-Y5-C5 IA0114 8 4 ISA-10-50-A-Y5-C5 IA019 8 4 ISA-10-50-A-Y5-M1 IA01 8 4 ISA-10-50-A-Y5-M18 IA01 8 4 ISA-10-50-A-Y5-M IA011 8 4 ISA-10-50-A-Y5-M0/M IA010 8 4 Mounting block No. 11 10D, 190150 8 6 Mounting block No. 1 11D, 19000 8 6 Mounting block No. 1 0D, 19050 8 6 Mounting block No. 14 D, 19000 8 6 Mounting block No. 15 0D, 19050 8 6 Mounting block No. 16 D, 190400 8 6 Mounting block No. 17 4D, 190450 8 6 Mounting block No. 18 40D, 19000 8 6 Mounting block No. 19 50D, 190050 8 6 Mounting block No. 140 64D, 190100 8 6 Protection cap M0 Delrin 75000470 8 7 Protection cap M0 PEEK 75000460 8 7 Protection cap M0 PTFE 75000450 8 7 Protection cap M Delrin 7500040 8 7 Protection cap M PEEK 75000410 8 7 Protection cap M PTFE 75000400 8 7 Protection set M18/PTFE 19605 8 7 Protection set M0/PTFE 1960 8 7 Protection set M/PTFE 19601 8 7 All specifications are subject to change without notice. (05/004) 94 RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de

All specifications are subject to change without notice. (05/004) RECHNER Industrie-Elektronik GmbH Gaußstraße 8-10 D-686 Lampertheim Tel. +49 (0) 6 06 50 07-0 Fax +49 (0) 6 06 50 07-0 email info@rechner-sensors.de www.rechner-sensors.de 95

SENSORS FOR INDUSTRIAL AUTOMATION INDUCTIVE CACITIVE OPTOELECTRONIC MAGNETO-RESISTIVE CALORIMETRIC Ask for further catalogues CACITIVE SENSORS KAS CACITIVE SENSORS KXS MAGNETORESISTIVE SENSORS OPTOELECTRONIC SENSORS ISOLATING SWITCHING AMPLIFIERS AND POWER SUPPLIES CACITIVE LEVEL MEASURING SYSTEMS FLOW SENSORS Your Representative: INDUSTRIE-ELEKTRONIK GmbH Gaußstraße 8-10 686 Lampertheim Germany Tel. +49 (0) 6 06 50 07-0 Fax Intl. +49 (0) 6 06 50 07-0 www.rechner-sensors.de e-mail: info@rechner-sensors.de