Symmetric SHDSL Router TH200 series Two pairs (4-wire) G.SHDSL DSU/CSU for Multi Mega bit stream Description TH200, G.SHDSL modem, transports multi mega bit stream over one or two pair of copper wires using T C-PAM technology. This modem supports multiple data rates ranging from 64 Kbps to 4608 Kbps. TH200 equips with three DTE interfaces which includes, Ethernet and. The three different interfaces can work simultaneously by sharing the DSL bandwidth. The Ethernet interface meets IEEE 802.3 10/100 Base-T with MAC bridge functions, which allows -to- connection over the G.SHDSL lines. Application flexibility could be easily achieved by choosing user DTE interfaces and selection of data rates. The TH200 uses in-band Embedded Operation channel for controlling and monitoring the remote unit. The comprehensive diagnostics function developed includes G.SHDSL, E1 line performance monitoring, in-band numbering V.54 local and remote loopbacks and real time alarm report. Local craft port, LCD display and pushbuttons facilitate local configuration and diagnostics.
Product Application Switch Hub V35 FE1 TH200 G.SHDSL Line TH200 Router 10/100Base-T PBX Figure ( a ) TH200 Application Following figure shows a point-to-point application for three user DTE interfaces, i.e.,, FE1 and equipped on each TH200 Desktop to maximize application flexibilities. According to its point of deployment, the TH200 could function as SHDSL transport device in central office or SHDSL transport device at customer premises. Note: : SHDSL Transciver Unit-Central : User DTE interface : SHDSL Transciver Unit-Remote In reference to Figure ( a ), Figure ( b ) but then illustrates with 2 pair SHDSL loop point to point application. Figure ( b ) 2 pair point to point application To eliminate the possible loop failure, a stand by SHDSL loop 2 shown on Figure ( c ) automatically takes the role of SHDSL loop1 when loop 1 experienced failure. Working DSL1 Stand By Figure ( c ) 1+1 DSL loop protection To maximize the user bandwidth, Figure ( d ) illustrates a to connectivity at two loop application.
Figure ( d ): Ethernet Bridging To transport variety of user bit stream at nx64k bps time slot at customer premises, the shown on Figure ( e ) Facilitates the transport of these time slot to the two interface, eliminating CSU/DSU required, at central offices. WAN/SDH Figure (e) Transport of 2 at CO To transport variety of user time slot at nx64k bps, or Fractional for example, at customer premises, the shown on Figure ( f ) Facilitates the transport of these time slot to the two interface, eliminating CSU/DSU required, at central offices. To Perform diagnostic end to end down the user link, Station 1 could address Station 2, 3 or 4 to perform V.54 loop back at the specified interface. Station N could be addressed up to N=32. Station 1 Station 2 Station 3 Station 4 WAN/SDH Loop back Loop back Loop back Figure ( f ): Transport of 2 at CO and perform numbering V.54 loop
Features Meet ITU-T G.991.2 standard Programmable for single, two loops and 1+1 protection mode operations Supports DTE data rate from 64Kbps to 4608 Kbps per 64Kbps increment Interfaces for either, plus F or 2 plus [or ] interfaces G.703 interface can be programmed as T1 or E1 Optional software configured for /V.36/RS-530/X.21, and F can work simultaneously by Nx64K time slot assignments Remote control and monitoring using in-band EOC channel Supports DSL PRBS BER test Supports numbering V.54 local and remote loopback Optional remote power feeding is programmable for 120V, 160V and 200V for full range DSL reach Supports wetting current G.SHDSL and line performance monitoring 96*15 minute and 7*24 hours performance data storage Optional SNMP agent embedded in Desktop unit. Optional T1/E1 front access test jack Field software upgradeable Automatic DSL loop crossover detection and operation. Supports two interfaces for better network provisioning. Hot swappable. Plug-in card swappable. Specification G.SHDSL line Line Coding: 16 TC-PAM, 32 TC-PAM is selectable Line Rate: 192K bps ~ 2312 Kbps for one DSL loop, 384K bps ~ 4624 Kbps for two DSL loops Total data rate: 64K - 4608 Kbps [NX64Kbps, N=1-72] which is shared by all active interfaces Protection: ITU-T K.20, K.21 and IEC60950 Standard: ITU-T G.991.2, Annex A [Default], Annex B is selectable 2 Pair DSL Loops with 0.4 m/m wire @ Ber 10-7 Rate(Kbps) 384 768 1536 2048 3072 4096 4608 Distance(km) 6.3 5.5 4.8 4.5 4.1 3.9 3.8
Data interfaces TH200 is able to support multiple customer interfaces simultaneously as (1) 1 x F, 1x plus 1x Ethernet or (2) 2 x T1/E1 plus 1x [or Ethernet] Each interfaces' bandwidth can be assigned by NX64Kbps with 64Kbps increment. E1 Interface Line rate: 2048 KHz +/- 50 ppm Line Code: HDB3 Framing: PCM31, PCM30, PCM31C, PCM30C and unframed Data Rate: 64 Kbps to 2048K bps [NX64Kbps, N=1-32] Operation: Full E1 or fractional E1 Pulse shape: Meet ITU-T G.703 Impedance: balanced 120Ω +/- 5% resistive or unbalanced 75Ω +/-5% resistive T1 Interface Line rate: 1544 KHz +/- 32ppm Line code: AMI or B8ZS, selectable Framing: SF, ESF or unframed, selectable Data Rate: 64 Kbps to 1536Kbps [NX64Kbps, N=1-24] and 1544Kbps Operation: Full T1 or fractional T1 Pulse shape: Meet ITU-T G.703, LBO: 0-655 ft with ABAM cable per 133 ft step programmable Impedance: balanced 100Ω +/- 5% resistive DTE data port Interface Interface: Optional /V.36/RS-530/X.21 software selectable Data Rate: 64 Kbps to 4608 Kbps Connector: MR34 Interface Interface: IEEE 802.3 / 802.3u 10/100 Base-T, Mac Address filtering bridge which supports up to 128 Mac address learning Data Rate: 64 Kbps to 4608 Kbps, NX64Kbps, N=1-72 Bridge: IEEE 802.1D transport, self-learning Connector: RJ-45
System timing Payload timing (1) Internal clock, accuracy +/- 32ppm (2) T1/E1 input clock (3) Data port DTE clock[tt] (4) Recovered clock (5) External clock SHDSL timing (1) Plesiochronous, local oscillator: 22.1184MHz +/- 32ppm (2) Synchronous (3) Hybrid Jitter and Wander Meets G.823 and G.824 jitter and wander requirements for T1/E1 interface Remote Line power feeding [optional] If line power feed option is chosen then AH200GT can generate line power for 120V, 160V and 200V for various DSL reach applications. Line power voltage is user programmable. Wetting Current 1-20 ma for each DSL loops, Activate via menu screen Maintenance Loopbacks: Local and remote loopbacks via front panel loopback buttons, VT-100 menu screen or in-band numbering V.54 loopback codes DSL PRBS BER testing DSL SNR and attenuation display SNR, LOSW, ES, SES and UAS for DSL loops Supports G.821 and G.826 error performance statistics for T1/E1 interfaces Management Interface: TH200 PIC (plug in card) Local craft port: RS-232/DB-9 for VT-100 TH200 Desktop Local craft port: RS-232/DB-9 for VT-100 Optional SNMP agent embedded
MCU plug in card [optional] SNMP meets IETF RFC1155,1212,3276 and 2495 port: IEEE 802.3 10/100 Base T, RS-232 for VT100 Major, Minor alarm LEDs and associated audible and visible form C relay contacts ACO switch and ACO LED indicator System Capacity For rack mounted shelf: 1 16 x TH200 plug in cards + 1 MCU card for Network Management Power input DC: -36 ~ -72 VDC AC: 90 ~ 260V AC ( 47 ~ 63 Hz ) For desktop enclosure, AC and DC power source can be field selectable. The AC and DC power inputs can be served as power protection mutually. TH200 shelf supports two DC - 48V power inputs for protection[a/b power]. Power consumptions TH200 plug in card: 7.5 Watts (Max.) for 2 pairs and no line powering MCU plug in card: 5 Watts (Max.) Environment Temperature: 0 ~ 60 C Humidity: Up to 95% non-condensing Dimensions Plug in card: 25x210x190 mm ( WxLxH ) Rack mount shelf: 432 x 300 x 217 mm (WxLxH) Desktop enclosure: 216.4 x 296.4 x 76.7 mm (WxLxH) Optional FAN tray: 432 x 300 x 42.875 mm (WxLxH) CE marking: EN 55022 and 55024 compliant Safety: EN60950 compliant Surge immunity: L1:L2 1KV, L1/L2:PE 2KV Lighting Surge: 4KV
Ordering Information TH200 PIC-i1-i2-i3-i4-i5-i6 (For Rack Mounting SHDSL unit) i1: 01: Single pair G.SHDSL only, 02: Two pair G.SHDSL i2: Specifies interface D1: One, D2: Two, D0: No i3: Specifies Data port interface V : fixed, SC: Soft configured for (or RS-530/X.21) X : No data port i4: Specifies interface L : 10/100 Base-T, X : No 10/100 Base-T i5: Specifies remote power feeding P1 : One pair, P2 : Two pair, X : No power feeding I6: Specifies front test jack TJ: front test jack X : No test jack TH200 Desktop-i1-i2-i3-i4-i5-i6-i7 (F or Desktop unit) i1: 01: Single pair G.SHDSL only, 02: Two pair G.SHDSL i2: Specifies interface D1: One, D2: Two, D0: No i3: Specifies Data port interface V : fixed, SC: Soft configured for (or RS-530/X.21) X : No data port i4: Specifies interface L : 10/100 Base-T, X : No 10/100 Base-T i5: Specifies remote power feeding P1 : One pair, P2 : Two pair, X : No power feeding I6: Specifies front test jack TJ: front test jack X : No test jack I7: Specifies SNMP support SNMP: SNMP agent embedded X: No SNMP agent Note that SNMP support could not co-exist with Front Access Test. TH200 Shelf-i1 (For Rack Mountable Shelf)) i1: 01 : Shelf without FAN tray, 02 : Shelf with FAN tray MCU Control Unit (For Network management system) Ordering example
TH200 PIC-02-D1-V-L-X-TJ means TH200 plug in card equipped with 2 pair SHDSL transcivers, one, one and one Ethernet interfaces, Front Access Test Jack, but no power feeing to remote unit. TH200 Desktop-02-D0-X-L-AD-X-SNMP means TH200 Desktop unit equipped with 2 pair SHDSL transcivers, one Ethernet interfaces, SNMP agent, No test jack, powered by AC, or DC at field selectable, but no power feeding to the remote unit