ECE0528i/ECE0548i Mini-ITX Chassis RISER CARD & FRONT 2.5 HDD ASSEMBLY (1) With Riser Card Expansion system integration, - The Slim ODD+2.5 HDD Bay and/or 3.5 HDD Bay are no longer installable due to space limitation in the smaller dimensioned Mini-ITX Chassis. (2) To install the Riser Card, - Break off and remove the Punched-but-not-perforated Slot Cover (For Standard PCI Card) from the Rear Panel, Unscrew and take out the Card Holder Bracket. Insert the Riser Card into the Motherboard s PCI Slot and, Use 2 pcs of 6-32*L6 Hexagon Head Screws to secure the Riser Card on the Center Bar. (3) Insert your Expansion Card horizontally into the PCI Slot of (4) With Riser Card expansion system integration, - the Riser Card. 1 pc of 2.5" HDD is installable on the inner side of the Steel Fit back the Card Holder Bracket on the Rear Panel and, - Front Panel. Use 1 pc of 6-32*L6 Hexagon Head Screw secure the Card Note: This installation of the 2.5" HDD would obstruct and Holder Bracket on the Rear Panel. invalidate the Card Reader integration.
(5) To install the 2.5 HDD on the inner side of the Steel Front (6) Use 2 pcs of 6-32*L4 Flat Head Screws to secure the Panel 2.5" HDD Fixture Bracket onto the Chassis Frame First, dismantle the Front Panel from the Chassis Frame. (Blocking and covering the Slim ODD s Inlet). Take out the 2.5 HDD Fixture Bracket (Steel Bracket Cover for the Slim ODD s Inlet) from the Accessory Box, Fit 2 pcs of Shockproof Rubber Cushions into the widest apart Circular Holes of the 2.5 HDD Fixture Bracket. Break off and remove the 3-Circular Punched-but-not-perforated Covers on the Front Steel Panel of the Chassis Frame and, - Insert 2 pcs of Shockproof Rubber Cushions in the widest apart holes. (7) Position the 2.5" HDD on the inner side of the Front Steel Panel and align its bottom mounting screw holes. (8) Take care to position the 2.5" HDD with its rear cable connecting ports towards the Front I/O side.
(9) Use 4 pcs of M3*0.5*L8 Hexagon Head Screws included with EMI Clips to secure the 2.5" HDD on the Front Steel Panel from the front to complete the installation.
ECE0528i/ECE0548i Mini-ITX Chassis 3.5 HDD ASSEMBLY (1) Before assembling the systems, - (2) Use 2 pcs of 6#-32*L4 Flat Head Screws to Dismantle the Front Panel from the Chassis Frame, Secure the 2.5 HDD Bracket onto the front steel panel of Unscrew and remove the 3.5 HDD Bay (Including the 4 pcs of the Chassis Frame (Covering the Slim ODD Inlet). Shockproof Rubber Cushions inserted in the 3.5 HDD Bay). Use 4 pcs of Shockproof Rubber Cushions and EMI Take out the 2.5 HDD Bracket (Steel Bracket Cover for the Clipped M3*0.5*L8 Hexagon Head Screws to secure the Slim ODD s Inlet) from the Accessory Box and, - 3.5 HDD in the 3.5 HDD Bay. Insert 2 pcs of Shockproof Rubber Cushions into the widest apart Circular Holes. (3) Before installing back the Front Panel onto the Chassis, -. Secure the Slim ODD s Plastic Bay Cover, Seat the assembled 3.5 Drive Bay back into the Chassis, Use 2 pcs of 6#-32*L4 Flat Head Screws to secure the 3.5 HDD Bay on the Chassis Frame and then, - Clip the Front Panel back into the Chassis Frame to complete.
ECE0528i/ECE0548i Mini-ITX Chassis STANDARD ASSEMBLY 1. Before assembly, - Dismantle the Plastic Slim ODD Cover from the Front Panel, Remove the Slim ODD+2.5 Bay (Or 3.5" HDD Bay) and the Center Bar from the Main Chassis Frame. 2. To install the bigger size FSP170-60SI/FSP220-6PLA Power Supply, - Break off and remove the excess Punched-but-not-perforated Bracket on the Rear Panel so that the Opening on the Rear Panel matches to the size of the Power Supply. (3) Place the Power Supply inside the case and, - Use 3 pcs of 6-32*L6 Hexagon Head Screw to secure the Power Supply from the Rear Panel. (4) Use 4 pcs of 6-32*L6 Hexagon Head Screws to install and secure the Motherboard. If Low Profile Expansion Card is required, - Unscrew and remove the Card Holder Bracket on the Rear Panel, Break off and remove the Punched-but-not-perforated Low Profile Slot Cover on the Rear Panel.
(5) Insert the Low Profile Expansion Card into the Motherboard's Slot. (6) Fit back the Center Bar and secure it on the Main Chassis Frame with 2 pcs of 6-32*L4 Flat Head Screws. (7) The Slim ODD Bay is designed with a detachable 2.5" HDD (8) Use 4 pcs of M2*0.4p*L3 Flat Head Screws to secure Bay to match multiple Motherboards systems. the Slim ODD. Use 4 pcs of M3*0.5p*L5 Flat Head Screws to secure the 2.5" HDD.
(9) The Slim ODD Bay can be installed with, or without the 2.5 (10) The 2.5" HDD Bay can be exempted for systems HDD Bay. Above photo shows integration of D201GLYA/D945GCLF/D945GCLF2 Slim ODD+2.5 HDD Bay installed with 2.5" HDD and, - Motherboards. (Only the Slim ODD Bay is used) Slim ODD Bay only installed with 2.5 HDD. (11) For the system integration of DC45FC Motherboard, - The 2.5" HDD must be secured in the 2.5" HDD Bay and Its position must be shifted to the right side of the Slim ODD position (To avoid height obstruction with CPU Cooler). (12) To exempt the use of the 2.5" HDD Bay and use only the Slim ODD Bay, - Use 4 pcs of M3*0.5p*L5 Flat Head Screws to secure the 2.5" HDD directly to the base of the Slim ODD Bay.
(13) Seat the assembled Slim ODD Bay back into the case and, - Use 2 pcs of 6-32*L4 Flat Head Screws to secure the Slim ODD Bay onto the Center Bar and Main Chassis Frame. (14) When only the Slim ODD Bay is used, there is internal space to allow the insertion of Low Profile Expansion Card. (15) When both the Slim ODD+2.5 HDD Bay are used, - The 2.5 HDD would interfere with the Low Profile Expansion Card (Space and construction limitation). (16) The use of both Slim ODD and 2.5" HDD Bay is therefore, not capable to accommodate the Low Profile Expansion Card systems.