Electrotechnical standards relevant for the oil and gas industry

Electrotechnical standards relevant for the oil and gas industry / 1 REPORT 530 MARCH 2015 Electrotechnical standards relevant for the oil and gas industry

Electrotechnical standards relevant for the oil and gas industry / 2 Contents Contents 2 Acknowledgement 3 Disclaimer 3 Copyright notice 3 Introduction 4 Purpose of report 5 Abbreviations 6 IEC standards specific to the oil and gas industry 8 IEC standards relevant for the oil and gas industry 9 API Standards 50 IEEE (PCIC) Standards 51 NEMA National Electrical Manufacturers Association 58 NFPA codes & standards 61 EEMUA publications 62 UL standards 63 Classification society s standards 66 Energy Institute documents 67 EN standards 68 GSO Electrotechnical standards 71 Other relevant codes, documents & standards 72

Electrotechnical standards relevant for the oil and gas industry / 3 Acknowledgement This report was developed by the IOGP Electrical Standards Subcommittee. Disclaimer Whilst every effort has been made to ensure the accuracy of the information contained in this publication, neither IOGP nor any of its Members past present or future warrants its accuracy or will, regardless of its or their negligence, assume liability for any foreseeable or unforeseeable use made thereof, which liability is hereby excluded. Consequently, such use is at the recipient's own risk on the basis that any use by the recipient constitutes agreement to the terms of this disclaimer. The recipient is obliged to inform any subsequent recipient of such terms. Copyright notice The contents of these pages are International Association of Oil & Gas Producers. Permission is given to reproduce this report in whole or in part provided (i) that the copyright of IOGP and (ii) the source are acknowledged. All other rights are reserved. Any other use requires the prior written permission of IOGP. These Terms and Conditions shall be governed by and construed in accordance with the laws of England and Wales. Disputes arising here from shall be exclusively subject to the jurisdiction of the courts of England and Wales.

Electrotechnical standards relevant for the oil and gas industry / 4 Introduction The International Association of Oil & Gas Producers (IOGP) organized a workshop 10 11 May 2012, in London, within the scope of electrical standards and practices for the oil and gas industry for electrical technology specialists of IOGP Members and invited guests. The objectives of the workshop were to: arrange for global networking amongst the specialists review and discuss the available standards for electrical installations, ongoing standards work and existing company specifications related to this discipline evaluate the needs for improvements of available industry, national or regional standards or company specifications and harmonization with international standards in this area evaluate the need for new electrical standards work in the oil and gas industry share company and/or personal experience regarding electrical installations, standards and practices. Within the goal for the workshop was also to identify and prioritize improvements to available standards or the need for new international (IEC) standards in the electrical area for the benefit of the global oil and gas industry. A draft of this report was initially prepared as a basis for this workshop and, following input from this workshop, IOGP has established the Electrical Standards Subcommittee with the same objectives as for the workshop. The Subcommittee has subsequently agreed to complete this document as an IOGP reference report including input from its Members and a benchmarking exercise in 2013. This report should be seen in conjunction with the following IOGP reports: Report 362, Catalogue of international standards used in the petroleum and natural gas industries (February 2012) where a number of IEC standards are identified Report 381, Position paper on the development and use of international standards (March 2010) outlining the importance of IEC standards Report 426, Regulators use of standards (March 2010) including some references to IEC standards Report 450, Benchmarking on the use of internal technical specifications and external standards by some oil & gas companies (February 2011).

Electrotechnical standards relevant for the oil and gas industry / 5 Purpose of report The purpose of this report is to provide a list of some of the available and relevant international, regional, national and industry electrotechnical standards for the oil and gas industries as seen by the participants of the IOGP Electrical Standards Subcommittee. This report is not exhaustive in any way and there may well be other relevant electrotechnical standards for the oil and gas industries.

Electrotechnical standards relevant for the oil and gas industry / 6 Abbreviations API ABS BV CRE CSA C-NLOPB DNV DNV- GL EEMUA EI GSO IALA IAPH IACS ICAO IAS ICS IEC IEE IEEE IET IMCA IMO ISO American Petroleum Institute American Bureau of Shipping Bureau Veritas Committee of Refining Equipment (under API) Canadian Standards Association Canada-Newfoundland and Labrador Offshore Petroleum Board Det Norske Veritas Det Norske Veritas GL Engineered Equipment Materials User Association Energy Institute (formerly Institute of Petroleum) Standardization Organization for the Cooperation Council for the Arab States of the Gulf International Association of Marine Aids to Navigation and Lighthouse Authorities International Association of Ports and Harbors International Association of Classification Societies International Civil Aviation Organization Industry Applications Society (under IEEE) International Chamber of Shipping International Electrotechnical Commission Now IET Institute of Electrical and Electronics Engineers Institution of Engineering and Technology International Maritime Contractors Association International Maritime Organization International Organization for Standardization

Electrotechnical standards relevant for the oil and gas industry / 7 ISGOTT ISPS LR MARPOL MEPC NEC NEK NEMA NFPA OCIMF IOGP PCIC SCAPC SCC SDO SOEE SOLAS TC UL USCG International Safety Guide for Oil Tankers and Terminals International Ships and Port Facilities Security Code Lloyds Register International Convention for the Prevention of Pollution From Ships (IMO) Marine Environment Protection Committee (in IMO) National Electrical Code Norwegian Electrotechnical Committee National Electrical Manufacturers Association National Fire Protection Association Oil Companies International Marine Forum International Association of Oil & Gas Producers Petroleum and Chemical Industry Committee (under IEEE IAS) Standards and Conformity Assessment Policy Committee (under NEMA) Standards Council of Canada Standards Developing Organization Subcommittee on Electrical Equipment International Convention of Safety Of Life At Sea (IMO) Technical Committee Underwriters Laboratories U.S. Coast Guard

Electrotechnical standards relevant for the oil and gas industry / 8 IEC standards specific to the oil and gas industry IEC 61892-1, Mobile and fixed offshore units Electrical installations Part 1: General requirements and conditions IEC 61892-2, Mobile and fixed offshore units Electrical installations Part 2: System design IEC 61892-3, Mobile and fixed offshore units Electrical installations Part 3: Equipment IEC 61892-4, Mobile and fixed offshore units Electrical installations Part 4: Cables IEC 61892-5, Mobile and fixed offshore units Electrical installations Part 5: Mobile units IEC 61892-6, Mobile and fixed offshore units Electrical installations Part 6: Installation IEC 61892-7, Mobile and fixed offshore units Electrical installations Part 7: Hazardous areas

Electrotechnical standards relevant for the oil and gas industry / 9 IEC standards relevant for the oil and gas industry IEC 60034, Rotating electrical machines IEC 60034-1, Rotating electrical machines Part 1: Rating and performance IEC 60034-11, Rotating electrical machines Part 11: Thermal protection IEC 60034-12, Rotating electrical machines Part 12: Starting performance of single-speed three phase cage induction motors IEC 60034-14, Rotating electrical machines Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher Measurement, evaluation and limits of vibration severity IEC 60034-15, Rotating electrical machines Part 15: Impulse voltage withstand levels of formwound stator coils for rotating a.c. machines IEC 60034-16, Excitation systems for synchronous machines IEC 60034-16-1, Rotating electrical machines Part 16: Excitation systems for synchronous machines - Chapter 1: Definitions IEC 60034-18, Rotating electrical machines Part 18: Functional evaluation of insulation systems IEC 60034-18-1, Rotating electrical machines Part 18-1: Functional evaluation of insulation systems General guidelines IEC 60034-18-21, Rotating electrical machines Part 18: Functional evaluation of insulation systems Section 21: Test procedures for wire-wound windings - Thermal evaluation and classification IEC 60034-18-22, Rotating electrical machines Part 18-22: Functional evaluation of insulation systems Test procedures for wire-wound windings - Classification of changes and insulation component substitutions IEC 60034-18-31, Rotating electrical machines Part 18-31: Functional evaluation of insulation systems Test procedures for form-wound windings Thermal evaluation and classification of insulation systems used in rotating machines IEC 60034-18-32, Rotating electrical machines Part 18-32: Functional evaluation of insulation systems Test procedures for form-wound windings - Evaluation by electrical endurance IEC 60034-18-33, Rotating electrical machines Part 18-33: Functional evaluation of insulation systems Test procedures for form-wound windings Multifactor evaluation by endurance under simultaneous thermal and electrical stresses

Electrotechnical standards relevant for the oil and gas industry / 10 IEC 60034-18-34, Rotating electrical machines Part 18-34: Functional evaluation of insulation systems Test procedures for form-wound windings Evaluation of thermomechanical endurance of insulation systems IEC 60034-18-41, Rotating electrical machines Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters IEC 60034-18-42, Rotating electrical machines Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters IEC 60034-19, Rotating electrical machines Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies IEC 60034-2, Rotating electrical machines Part 2-1:Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) IEC 60034-2-1, Rotating electrical machines Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles). IEC 60034-22, Rotating electrical machines Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets IEC 60034-2-2, Rotating electrical machines Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1 IEC 60034-2-3, Rotating electrical machines Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC motors IEC 60034-25, Rotating electrical machines Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply IEC 60034-26, Rotating electrical machines Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors IEC 60034-27, Rotating electrical machines Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines IEC 60034-28, Rotating electrical machines Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors IEC 60034-29, Rotating electrical machines Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise IEC 60034-2A, Rotating electrical machines Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) Measurement of losses by the calorimetric method IEC 60034-3, Rotating electrical machines Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

Electrotechnical standards relevant for the oil and gas industry / 11 IEC 60034-30, Rotating electrical machines Part 30: Efficiency classes of single-speed, threephase, cage-induction motors (IE-code) IEC 60034-31, Rotating electrical machines Part 31: Guide for the selection and application of energy-efficient motors including variable-speed applications IEC 60034-4, Rotating electrical machines Part 4: Methods for determining synchronous machine quantities from tests IEC 60034-5, Rotating electrical machines Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification IEC 60034-6, Rotating electrical machines Part 6: Methods of cooling (IC Code) IEC 60034-7, Rotating electrical machines Part 7: Terminal markings and direction of rotation. IEC 60034-8, Rotating electrical machines Part 8: Terminal markings and direction of rotation IEC 60034-9, Rotating electrical machines Part 9: Noise limits IEC 60038, IEC standard voltages IEC 60044, Instrument transformers IEC 60044-1, Instrument transformers Part 1: Current transformers IEC 60044-2, Instrument transformers Part 2 : Inductive voltage transformers IEC 60044-3, Instrument transformers Part 3: Combined transformers IEC 60044-5, Instrument transformers Part 5: Capacitor voltage transformers IEC 60044-6, Instrument transformers Part 6: Requirements for protective current transformers for transient performance IEC 60044-7, Instrument transformers Part 7: Electronic voltage transformers IEC 60044-8, Instrument transformers Part 8: Electronic current transformers IEC 60050, International Electrotechnical vocabulary IEC 60050-161, International Electrotechnical Vocabulary Chapter 161: Electromagnetic compatibility IEC 60050-191, International Electrotechnical Vocabulary Chapter 191: Dependability and quality of service IEC 60050-300, International Electrotechnical Vocabulary Electrical and electronic - measurements and measuring instruments IEC 60050-411, International Electrotechnical Vocabulary Part 411: Rotating machinery

Electrotechnical standards relevant for the oil and gas industry / 12 IEC 60050-426, International Electrotechnical Vocabulary Chapter 426: Equipment for explosive atmospheres IEC 60050-441, International Electrotechnical Vocabulary Chapter 441: Switchgear, controlgear and fuses IEC 60050-446, International Electrotechnical Vocabulary Chapter 446: Electrical relays IEC 60050-617, International Electrotechnical Vocabulary Part 617: Organization/Market of electricity - Edition 1.0 IEC 60050-702, International Electrotechnical Vocabulary Chapter 702: Oscillations, signals and related devices IEC 60050-826, International Electrotechnical Vocabulary Part 826: Electrical installations IEC 60050-845, International Electrotechnical Vocabulary Chapter 845: Lighting IEC 60051, Direct acting indicating analogue electrical measuring instruments and their accessories All Parts IEC 60051-1, Direct acting indicating analogue electrical measuring instruments and their accessories Part 1: Definitions and general requirements common to all parts IEC 60051-2, Direct acting indicating analogue electrical measuring instruments and their accessories Part 2: Special requirements for ammeters and voltmeters IEC 60051-3, Direct acting indicating analogue electrical measuring instruments and their accessories Part 3: Special requirements for wattmeters and varmeters IEC 60051-4, Direct acting indicating analogue electrical measuring instruments and their accessories Part 4: Special requirements for frequency meters IEC 60051-5, Direct acting indicating analogue electrical measuring instruments and their accessories Part 5: Special requirements for phase meters, power factor meters and synchroscopes IEC 60051-6, Direct acting indicating analogue electrical measuring instruments and their accessories Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters IEC 60051-7, Direct acting indicating analogue electrical measuring instruments and their accessories Part 7: Special requirements for multi-function instruments IEC 60051-8, Direct acting indicating analogue electrical measuring instruments and their accessories Part 8: Special requirements for accessories IEC 60051-9, Direct acting indicating analogue electrical measuring instruments and their accessories Part 9: Recommended test methods IEC 60059, IEC standard current ratings

Electrotechnical standards relevant for the oil and gas industry / 13 IEC 60060, High-voltage test techniques. IEC 60060-1, High-voltage test techniques Part 1: General definitions and test requirements IEC 60060-2, High voltage test techniques Part 2: Measuring systems IEC 60060-3, High-voltage test techniques Part 3: Definitions and requirements for on-site testing IEC 60061-1, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamp caps IEC 60064, Tungsten filament lamps for domestic and similar general lighting purposes Performance requirements IEC 60068, Environmental testing IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold IEC 60068-2-14, Environmental testing Part 2-14: Tests Test N: Change of temperature IEC 60068-2-2, Environmental testing Part 2-2: Tests Test B: Dry heat IEC 60068-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle) IEC 60068-2-52, Environmental testing Part 2: Tests, Test Kb: Salt mist, cyclic (sodium chloride solution) IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-75, Environmental testing Part 2: Tests Test Eh: Hammer tests IEC 60068-2-78, Draft Document - Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60071, Insulation co-ordination IEC 60071-1 Insulation co-ordination Part 1: Definitions, principles and rules IEC 60071-2 Insulation co-ordination Part 2: Application guide IEC 60071-4 Insulation co-ordination Part 4: Computational guide to insulation co-ordination and modelling of electrical networks IEC 60071-5 Insulation co-ordination Part 5: Procedures for high-voltage direct current (HVDC) converter stations

Electrotechnical standards relevant for the oil and gas industry / 14 IEC 60072, Dimensions and output series for rotating electrical machines IEC 60072-1, Dimensions and output series for rotating electrical machines Part 1: Frame numbers 56 to 400 and flange numbers 55 to 1080 IEC 60072-2, Dimensions and output series for rotating electrical machines Part 2: Frame numbers 355 to 1000 and flange numbers 1180 to 2360 IEC 60072-3, Dimensions and output series for rotating electrical machines Part 3: Small built-in motors - Flange numbers BF10 to BF50 IEC 60073, Basic and safety principles for man-machine interface, marking and identification Coding principles for indicators and actuators IEC 60076, Power transformers (all parts) IEC 60076-1, Power transformers Part 1: General IEC 60076-10, Power transformers Part 10: Determination of sound levels IEC 60076-10-1, Power transformers Part 10-1: Determination of sound levels Application guide IEC 60076-11, Power transformers Part 11: Dry-type transformers IEC 60076-12, Power transformers Part 12: Loading guide for dry-type transformers IEC 60076-13, Power transformers Part 13: Self-protected liquid-filled transformers IEC 60076-14, Power transformers Part 14: Design and application of liquid-immersed power transformers using high-temperature insulation materials IEC 60076-15, Power transformers Part 15: Gas-filled power transformers IEC 60076-16, Power transformers Part 16: Transformers for wind turbine applications IEC 60076-17, Power transformers Part 17: Evaluation of electromagnetic fields around power transformers IEC 60076-18, Power transformers Part 18: Measurement of frequency response IEC 60076-2, Power transformers Part 2: Temperature rise for liquid-immersed transformers IEC 60076-21, Power Transformers Part 21: Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators IEC 60076-3,Power transformers Part 3: Insulation levels, dielectric tests and external clearances in air IEC 60076-3-1, Power Transformers External Clearances In Air IEC 60076-4, Power transformers Part 4: Guide to the lightning impulse and switching impulse testing Power transformers and reactors

Electrotechnical standards relevant for the oil and gas industry / 15 IEC 60076-5, Power transformers Part 5: Ability to withstand short circuit IEC 60076-6, Power transformers Part 6: Reactors IEC 60076-7, Power transformers Part 7: Loading guide for oil-immersed power transformers IEC 60076-8, Power transformers Part 8: Application guide IEC 60079, Electrical apparatus for explosive gas atmospheres IEC 60079-0, Explosive atmospheres Part 0: Equipment General requirements IEC 60079-1, Electrical apparatus for explosive gas atmospheres Flameproof enclosures 'd' IEC 60079-10, Electrical apparatus for explosive gas atmospheres Part 10: Classification of hazardous areas IEC 60079-10-1, Explosive atmospheres Part 10-1: Classification of areas Explosive gas atmospheres IEC 60079-10-2, Explosive atmospheres Part 10-2: Classification of areas Combustible dust atmospheres IEC 60079-11, Explosive atmospheres Part 11: Equipment protection by intrinsic safety "i" IEC 60079-13, Electrical apparatus for explosive gas atmosphere Part 13: Construction and use of rooms or buildings protected by pressurization IEC 60079-14, Explosive atmospheres Part 14: Electrical installations design, selection and erection IEC 60079-15, Explosive atmospheres Part 15: Equipment protection by type of protection "n" IEC 60079-16, Electrical apparatus for explosive gas atmospheres Part 16: Artificial ventilation for the protection of analyser(s) houses IEC 60079-17, Explosive atmospheres Part 17: Electrical installations inspection and maintenance IEC 60079-18, Explosive atmospheres Part 18: Equipment protection by encapsulation m IEC 60079-19, Explosive atmospheres Part 19: Equipment repair, overhaul and reclamation IEC 60079-2, Explosive atmospheres Part 2: Equipment protection by pressurized enclosure p IEC 60079-20, Explosive atmospheres Part 20: Material characteristics for gas and vapour classification IEC 60079-20-1, Explosive atmospheres Part 20-1: Material characteristics for gas and vapour classification Test methods and data IEC 60079-25, Electrical apparatus for explosive gas atmospheres Part 25: Intrinsically safe systems

Electrotechnical standards relevant for the oil and gas industry / 16 IEC 60079-26, Explosive atmospheres Part 26: Equipment with equipment protection level (EPL) Ga IEC 60079-27, Explosive atmospheres Part 27: Fieldbus intrinsically safe concept (FISCO) IEC 60079-28, Explosive atmospheres Part 28: Protection of equipment and transmission systems using optical radiation IEC 60079-29, Explosive atmospheres Part 29: Gas detectors; Selection, installation, use and maintenance of detectors for flammable gases and oxygen IEC 60079-29-1, Explosive atmospheres Part 29-1: Gas detectors Performance requirements of detectors for flammable gases IEC 60079-29-2, Explosive atmospheres Part 29-2: Gas detectors Selection, installation, use and maintenance of detectors for flammable gases and oxygen IEC 60079-29-3, Explosive atmospheres Part 29-3: Gas detectors- Requirements on the functional safety of fixed gas detection systems IEC 60079-29-4, Explosive atmospheres Part 29-4: Gas detectors Performance requirements of open path detectors for flammable gases IEC 60079-30-1, Explosive atmospheres Part 30-1: Electrical resistance trace heating General and testing requirements IEC 60079-30-2, Explosive atmospheres Part 30-2: Electrical resistance trace heating Application guide for design, installation and maintenance IEC 60079-31, Explosive atmospheres Part 31: Equipment dust ignition protection by enclosure "t" IEC 60079-33, Explosive atmospheres Part 33: Equipment protection by special protection 's' IEC 60079-35-1, Caplights for use in mines susceptible to firedamp Part 1: General requirements Construction and testing in relation to the risk of explosion IEC 60079-35-2, Caplights for use in mines susceptible to firedamp Part 2: Performance and other safety-related matters IEC 60079-5, Explosive atmospheres Part 5: Equipment protection by powder filling q IEC 60079-6, Explosive atmospheres Part 6: Equipment protection by oil immersion o IEC 60079-7, Explosive atmospheres Part 7: Equipment protection by increased safety e IEC 60081, Double-capped fluorescent lamps Performance specifications IEC 60083, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC IEC 60085, Electrical insulation Thermal evaluation and designation

Electrotechnical standards relevant for the oil and gas industry / 17 IEC 60092, Electrical installations in ships IEC 60092-101, Electrical installations in ships Part 101: Definitions and general requirements IEC 60092-201, Electrical installation in ships System design General IEC 60092-302, Electrical installation in ships Low-voltage switchgear and controlgear assemblies IEC 60092-350, Electrical installations in ships Part 350: General construction and test methods of power, control and instrumentation cables for shipboard and offshore applications IEC 60092-352, Electrical installations in ships Part 352: Choice and installation of electrical cables IEC 60092-353, Electrical installations in ships Part 353: Single and multicore non-radial field power cables with extruded solid insulation for rated voltages 1 kv and 3 kv IEC 60092-354, Electrical installations in ships Part 354: Single and three-core power cables with extruded solid insulation for rated voltages 6 kv (Um = 7,2 kv); up to 30 kv (Um = 36 kv) IEC 60092-360, Electrical installations in ships Part 360: Insulating and sheathing materials for shipboard and offshore units, power, control, instrumentation and telecommunication cables IEC 60092-370, Electrical installations in ships Part 370: Guidance on the selection of cables for telecommunication and data transfer including radio-frequency cables IEC 60092-376, Electrical installations in ships Part 376: Cables for control and instrumentation circuits 150/250 V (300 V) IEC 60092-401, Electrical installations in ships Part 401: Installation and test of completed installation IEC 60092-501, Electrical installations in ships Part 501: Special features Electric propulsion plant IEC 60092-502, Electrical installations in ships Part 502: Tankers, Special Features IEC 60092-504, Electrical installations in ships Part 504: Special features Control and instrumentation IEC 60092-509, Electrical installations in ships Part 509: Operation of electrical installations IEC 60095-1, Lead acid starter batteries Part 1: General requirements and methods of test IEC 60099, Lightening arresters IEC 60099-1, Surge arresters Part 1: Non-linear resistor type gapped surge arresters for a.c. systems IEC 60099-5, Surge arresters Part 5: Selection and application recommendations

Electrotechnical standards relevant for the oil and gas industry / 18 IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid insulating materials IEC 60120, Dimensions of ball & socket couplings of string insulator units IEC 60137, Insulated bushings for alternating voltages above 1000 V IEC 60146, Semiconductor convertors General requirements and line commutated convertors IEC 60146-1-1, Semiconductor converters General requirements and line commutated converters Part 1-1: Specification of basic requirements IEC 60146-1-2, Semiconductor converters - General requirements and line commutated converters Part 1-2: Application guide IEC 60146-1-3, Semiconductor converters General requirements and line commutated converters Part 1-3: Transformers and reactors IEC 60146-2, Semiconductor converters Part 2: Self-commutated semiconductor converters including direct d.c. converters IEC 60152, Identification by hour numbers of the phase conductors of 3-phase electric systems IEC 60155, Glow-starters for fluorescent lamps IEC 60156, Insulating liquids Determination of the breakdown voltage at power frequency Test method IEC 60169, Radio-frequency connectors IEC 60183, Guide to the selection of high-voltage cables IEC 60189-2, Low-frequency cables and wires with PVC insulation and PVC sheath Part 2: Cables in pairs, triples, quads and quintuples for inside installations IEC 60191-6, Mechanical standardization of semiconductor devices Part 6: General rules for the preparation of outline drawings of surface mounted semiconductor device packages IEC 60196, IEC standard frequencies IEC 60204-1, Electrical equipment of industrial machines Part 1: General rules IEC 60214, Tap-changers IEC 60214-1, Tap-changers Part 1: Performance requirements and test methods IEC 60214-2, Tap-changers Part 2: Application guide IEC 60215, Safety requirements for radio transmitting equipment IEC 60227, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V (all parts)

Electrotechnical standards relevant for the oil and gas industry / 19 IEC 60228, Conductors of insulated cables IEC 60229, Electric cables Tests on extruded oversheaths with a special protective function IEC 60243-1, Electric strength of insulating materials Test methods Part 1: Tests at power frequencies IEC 60245, Rubber insulated cables Rated voltages up to and including 450/750 V (all parts) IEC 60247, Insulating liquids Measurement of relative permittivity, dielectric dissipation factor (tan d) and d.c. resistivity IEC 60255, Electrical relays IEC 60255-1, Measuring relays and protection equipment Part 1: Common requirements IEC 60255-11, Measuring relays and protection equipment Part 11: Voltage dips, short interruptions, variations and ripple on auxiliary power supply port IEC 60255-12, Electrical relays Part 12: Directional relays and power relays with two input energizing quantities IEC 60255-121, Measuring relays and protection equipment Part 121: Functional requirements for distance protection IEC 60255-127, Measuring relays and protection equipment Part 127: Functional requirements for over/under voltage protection IEC 60255-13, Electrical relays Part 13: Biased (percentage) differential relays IEC 60255-151, Measuring relays and protection equipment Part 151: Functional requirements for over/under current protection IEC 60255-16, Electrical relays Part 16: Impedance measuring relays IEC 60255-21-1, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment - Section One: Vibration tests (sinusoidal) IEC 60255-21-2, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section Two: Shock and bump tests IEC 60255-21-3, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 3: Seismic tests IEC 60255-22-1, Measuring relays and protection equipment Part 22-1: Electrical disturbance tests 1 MHz burst immunity tests IEC 60255-22-2, Measuring relays and protection equipment Part 22-2: Electrical disturbance tests Electrostatic discharge tests IEC 60255-22-3, Measuring relays and protection equipment Part 22-3: Electrical disturbance tests Radiated electromagnetic field immunity

Electrotechnical standards relevant for the oil and gas industry / 20 IEC 60255-22-4, Measuring relays and protection equipment Part 22-4: Electrical disturbance tests - Electrical fast transient/burst immunity test IEC 60255-22-5, Measuring relays and protection equipment Part 22-5: Electrical disturbance tests - Surge immunity test IEC 60255-22-6, Electrical relays Part 22-6: Electrical disturbance tests for measuring relays and protection equipment Immunity to conducted disturbances induced by radio frequency fields IEC 60255-22-7, Electrical relays Part 22-7: Electrical disturbance tests for measuring relays and protection equipment Power frequency immunity tests IEC 60255-24, Electrical relays Part 24: Common format for transient data exchange (COMTRADE) for power systems IEC 60255-25, Electrical relays Part 25: Electromagnetic emission tests for measuring relays and protection equipment IEC 60255-26, Measuring relays and protection equipment Part 26: Electromagnetic compatibility requirements IEC 60255-27, Measuring relays and protection equipment Part 27: Product safety requirements IEC 60255-5, Electrical Relays Part 5: Insulation coordination for measuring relays and protection equipment Requirements and tests IEC 60255-6, Electrical relays Part 6: Measuring relays and protection equipment IEC 60255-8, Electrical relays Part 8: Thermal electrical relays IEC 60265-1, High-voltage switches Part 1: Switches for rated voltages above 1 kv and less than 52 kv IEC 60268, Sound system equipment IEC 60268-16, Sound system equipment Part 16: Objective rating of speech intelligibility by speech transmission index IEC 60268-3, Sound System Equipment Part 3: Amplifiers IEC 60269, Low-voltage fuses IEC 60269-1, Low-voltage fuses Part 1: General requirements IEC 60269-2, Low voltage fuses Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) IEC 60269-2-1, Low-voltage fuses Part 2-1: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Sections I to VI: Examples of types of standardized fuses

Electrotechnical standards relevant for the oil and gas industry / 21 IEC 60269-3, Low-voltage fuses Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F IEC 60270, High-voltage test techniques Partial discharge measurements IEC 60282-1, High-voltage fuses Part 1: Current-limiting fuses IEC 60282-2, High-voltage fuses Part 2: Expulsion fuses IEC 60287, Electric cables Calculation of the current rating (all parts) IEC 60287-1-1, Electric cables Calculation of the current rating Part 1-1: Current rating equations (100 % load factor) and calculation of losses - General IEC 60287-1-2, Electric cables Calculation of the current rating Part 1: Current rating equations (100 % load factor) and calculations of losses - Section 2: Sheath eddy current loss factors for two circuits in flat formation IEC 60287-1-3, Electric cables - Calculation of the current rating Part 1-3: Current rating equations (100 % load factor) and calculation of losses - Current sharing between parallel singlecore cables and calculation of circulating current losses IEC 60287-2-1, Electric cables - Calculation of the current rating Part 2-1: Thermal resistance - Calculation of thermal resistance IEC 60287-2-2, Electric cables - Calculation of the current rating Part 2: Thermal resistance - Section 2: A method for calculating reduction factors for groups of cables in free air, protected from solar radiation IEC 60287-3-1, Electric cables - Calculation of the current rating Part 3-1: Sections on operating conditions - Reference operating conditions and selection of cable type IEC 60287-3-2, Electric cables - Calculation of the current rating Part 3: Sections on operating conditions - Section 2: Economic optimization of power cable size IEC 60287-3-3, Electric cables - Calculation of the current rating Part 3-3: Sections on operating conditions - Cables crossing external heat sources IEC 60296, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear IEC 60298, AC Metal Enclosed Switchgear & Control gear for rated voltages above 1kV and up to and including 52kV IEC 60300, Dependability management IEC 60300-1, Dependability management Part 1: Dependability management systems IEC 60300-2, Dependability management Part 2: Guidelines for dependability management

Electrotechnical standards relevant for the oil and gas industry / 22 IEC 60300-3-1, Dependability management Part 3-1: Application guide Analysis techniques for dependability Guide on methodology IEC 60300-3-10, Dependability management Part 3-10: Application guide Maintainability IEC 60300-3-11, Dependability management Part 3-11: Application guide Reliability centred maintenance IEC 60300-3-12, Dependability management Part 3-12: Application guide Integrated logistic support IEC 60300-3-14, Dependability management Application guide Maintenance and maintenance support IEC 60300-3-15, Dependability management Application guide Engineering of system dependability IEC 60300-3-16, Dependability management Part 3-16: Application guide Guidelines for the specification of maintenance support services IEC 60300-3-2, Dependability management Part 3-2: Application guide Collection of dependability data from the field IEC 60300-3-3, Dependability management Application guide Life cycle costing IEC 60300-3-4, Draft Document Dependability Management Part 3: Application Guide Section 4: Guide to the Specification of Dependability Requirements IEC 60300-3-5, Dependability management Part 3-5: Application guide Reliability test conditions and statistical test principles IEC 60304, Standard colours for insulation for low-frequency cables and wires IEC 60309, Plugs, socket-outlets and couplers for industrial proposes IEC 60309-1, Plugs, socket-outlets and couplers for industrial purposes Part 1: General requirements IEC 60309-2, Plugs, socket-outlets and couplers for industrial purposes Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories IEC 60309-4, Plugs, socket-outlets and couplers for industrial purposes Part 4: Switched socketoutlets and connectors with or without interlock IEC 60317, Specifications for particular types of winding wires IEC 60331, Tests for electric cables under fire conditions Circuit integrity IEC 60331-1, Tests for electric cables under fire conditions Circuit integrity Part 1: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kv and with an overall diameter exceeding 20 mm

Electrotechnical standards relevant for the oil and gas industry / 23 IEC 60331-11, Tests for electric cables under fire conditions Circuit integrity Part 11: Apparatus - Fire alone at a flame temperature of at least 750 C IEC 60331-2, Tests for electric cables under fire conditions Circuit integrity Part 2: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kv and with an overall diameter not exceeding 20 mm IEC 60331-21, Tests for electric cables under fire conditions Circuit integrity Part 21: Procedures and requirements Cables of rated voltage up to and including 0,6/1,0 kv IEC 60331-23, Tests for electric cables under fire conditions Circuit integrity Part 23: Procedures and requirements - Electric data cables IEC 60331-25, Tests for electric cables under fire conditions Circuit integrity Part 25: Procedures and requirements Optical fibre cables IEC 60331-3, Tests for electric cables under fire conditions Circuit integrity Part 3: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kv tested in a metal enclosure IEC 60332, Tests on electric and optical fibre cables under fire conditions IEC 60332-1, Tests on electric and optical fibre cables under fire conditions Part 1: Test for vertical flame propagation for a single insulated wire or cable IEC 60332-1-1, Tests on electric and optical fibre cables under fire conditions Part 1-1: Test for vertical flame propagation for a single insulated wire or cable Apparatus IEC 60332-1-2, Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable Procedure for 1 kw pre-mixed flame IEC 60332-1-3, Tests on electric and optical fibre cables under fire conditions Part 1-3: Test for vertical flame propagation for a single insulated wire or cable Procedure for determination of flaming droplets/particles IEC 60332-2-1, Tests on electric and optical fibre cables under fire conditions Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable Apparatus IEC 60332-2-2, Tests on electric and optical fibre cables under fire conditions Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable Procedure for diffusion flame IEC 60332-3, Tests on electric cables under fire conditions (various Parts) - Test for vertical flame spread of vertically mounted bunched wires or cables IEC 60332-3-10, Tests on electric and optical fibre cables under fire conditions Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables Apparatus IEC 60332-3-21, Tests on electric cables under fire conditions Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables Category A F/R

Electrotechnical standards relevant for the oil and gas industry / 24 IEC 60332-3-22, Tests on electric cables under fire conditions Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables Category A IEC 60332-3-23, Tests on electric and optical fibre cables under fire conditions Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables Category B IEC 60332-3-24, Tests on electric and optical fibre cables under fire conditions Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables Category C IEC 60332-3-25, Tests on electric and optical fibre cables under fire conditions Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables Category D IEC 60335, Household and similar electrical appliances (relevant parts) IEC 60335-1, Household and similar electrical appliances Safety Part 1: General requirements IEC 60335-2-29, Household and similar electrical appliances Safety Part 2-29: Particular requirements for battery chargers IEC 60354, Loading Guide For Oil-Immersed Transformers IEC 60364, Low-voltage electrical installations IEC 60364-1, Low-voltage electrical installations Part 1: Fundamental principles, assessment of general characteristics, definitions IEC 60364-4-41, Low-voltage electrical installations Part 4-41: Protection for safety Protection against electric shock IEC 60364-4-43, Low-voltage electrical installations Part 4-43: Protection for safety Protection against overcurrent IEC 60364-4-44, Low-voltage electrical installations Part 4-44: Protection for safety Protection against voltage disturbances and electromagnetic disturbances. IEC 60364-5-52, Low-voltage electrical installations Part 5-52: Selection and erection of electrical equipment Wiring systems IEC 60364-5-53, Electrical installations of buildings Part 5-53: Selection and erection of electrical equipment Isolation, switching and control IEC 60364-5-54, Low-voltage electrical installations Part 5-54: Selection and erection of electrical equipment Earthing arrangement and protective conductors IEC 60364-5-548, Electrical installations of buildings Part 5: Selection and erection of electrical equipment Section 548: Earthing arrangements and Equipotential Bonding for information technology installations IEC 60364-5-55, Electrical installations of buildings Part 5-55: Selection and erection of electrical equipment Other equipment IEC 60364-6, Low voltage electrical installations Part 6: Verification

Electrotechnical standards relevant for the oil and gas industry / 25 IEC 60364-7-710, Electrical installations of buildings Part 7-710: Requirements for special installations or locations Medical locations IEC 60364-7-712, Electrical installations of buildings Part 7-712: Requirements for special installations or locations Solar photovoltaic (PV) power supply systems IEC 60376, Specification of technical grade sulfur hexafluoride (SF 6 ) for use in electrical equipment IEC 60383, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC IEC 60398, Industrial electroheating installations General test methods IEC 60400, Lampholders for tubular fluorescent lamps and starterholders IEC 60417, Graphical symbols for use on equipment IEC 60417-1, Graphical symbols for use on equipment Part 1: Overview and application IEC 60422, Mineral insulating oils in electrical equipment Supervision and maintenance guidance IEC 60432, Incandescent lamps Safety specifications IEC 60432-1, Incandescent lamps Safety specifications Part 1: Tungsten filament lamps for domestic and similar general lighting purposes IEC 60433, Insulators for overhead lines with a nominal voltage above 1 000 V Ceramic insulators for a.c. systems Characteristics of insulator units of the long rod type IEC 60439, Low-voltage switchgear and control gear assemblies. IEC 60439-1, Low-voltage switchgear and control gear assemblies Part 1: Type-tested and partially type-tested assemblies IEC 60439-2, Low-voltage switchgear and controlgear assemblies Part 2: Particular requirements for busbar trunking systems (busways) IEC 60439-4, Low-voltage switchgear and controlgear assemblies Part 4: Particular requirements for assemblies for construction sites (ACS) IEC 60446, Basic and safety principles for man-machine interface, marking and identification Identification of conductors by colours IEC 60447, Basic and safety principles for man-machine interface, marking and identification Actuating principles IEC 60449, Voltage bands for electrical installations of buildings IEC 60450, Measurement of the average viscometric degree of polymerization of new and aged cellulosic electrically insulating materials IEC 60454-2, Specifications for pressure-sensitive adhesive tapes For electrical purposes Part 2: Methods of test

Electrotechnical standards relevant for the oil and gas industry / 26 IEC 60470, High-voltage alternating current contactors IEC 60473, Dimensions for panel-mounted indicating and recording electrical measuring instruments IEC 60478, Stabilized power supplies, DC output IEC 60479, Guide to effects of current on human beings and livestock (Parts 1-4) IEC 60480, Guidelines for the checking and treatment of sulphur hexafluoride (SF 6 ) taken from electrical equipment and specification for its re-use IEC 60487, Methods of measurement for equipment used in terrestrial radio-relay systems. IEC 60502, Power cables with extruded insulation and their accessories for rated voltages from 1 kv (Um = 1,2 kv) up to 30 kv (Um = 36 kv) IEC 60502-1, Power cables with extruded insulation and their accessories for rated voltages from 1 kv (Um = 1,2 kv) up to 30 kv (Um = 36 kv) Part 1: Cables for rated voltages of 1 kv (Um = 1,2 kv) and 3 kv (Um = 3,6 kv) IEC 60502-2, Power cables with extruded insulation and their accessories for rated voltages from 1 kv (Um = 1,2 kv) up to 30 kv (Um = 36 kv) Part 2: Cables for rated voltages from 6 kv (Um = 7,2 kv) up to 30 kv (Um = 36 kv) IEC 60502-4, Power cables with extruded insulation and their accessories for rated voltages from 1 kv (Um = 1,2 kv) up to 30 kv (Um = 36 kv) Part 4: Test requirements on accessories for cables with rated voltages from 6 kv (Um = 7,2 kv) up to 30 kv (Um = 36 kv) IEC 60519-10, Safety in electroheat installations Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 60533, Electrical and electronic installations in ships Electromagnetic compatibility IEC 60534, Industrial-process control valves IEC 60534-1, Industrial-process control valves Part 1: Control valve terminology and general considerations IEC 60534-2, Industrial-process control valves Part 2: Flow capacity IEC 60534-2-1, Industrial-process control valves Part 2-1: Flow capacity Sizing equations for fluid flow under installed conditions IEC 60534-2-3, Industrial-process control valves Part 2-3: Flow capacity Test procedures IEC 60534-2-4, Industrial-process control valves Part 2-4: Flow capacity Inherent flow characteristics and rangeability IEC 60534-2-5, Industrial-process control valves Part 2-5: Flow capacity Sizing equations for fluid flow through multistage control valves with interstage recovery

Electrotechnical standards relevant for the oil and gas industry / 27 IEC 60534-3-1, Industrial-process control valves Part 3-1: Dimensions Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves IEC 60534-3-2, Industrial-process control valves Part 3-2: Dimensions Face-to-face dimensions for rotary control valves except butterfly valves IEC 60534-3-3, Industrial-process control valves Part 3-3: Dimensions End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves IEC 60534-4, Industrial-process control valves Part 4: Inspection and routine testing IEC 60534-5, Industrial-process control valves Part 5: Marking IEC 60534-6-1, Industrial-process control valves Part 6: Mounting details for attachment of positioners to control valves Section 1: Positioner mounting on linear actuators IEC 60534-6-2, Industrial-process control valves Part 6-2: Mounting details for attachment of positioners to control valves Positioner mounting on rotary actuators IEC 60534-7, Industrial process control valves Part 7: Control valve data sheet IEC 60534-8-3, Industrial-process control valves Part 8-3: Noise considerations Control valve aerodynamic noise prediction method IEC 60534-8-4, Industrial-process control valves Part 8-4: Noise considerations Prediction of noise generated by hydrodynamic flow IEC 60536, Classification of electrical and electronic equipment with regard to protection against electric shock. IEC 60549, High-voltage fuses for the external protection of shunt power capacitors IEC 60567, Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved gases Guidance IEC 60584-1, Thermocouples Part 1: Reference tables IEC 60584-2, Thermocouples Part 2: Tolerances IEC 60584-3, Thermocouples Part 3: Extension and compensating cables - Tolerances and identification system IEC 60598, Luminaires IEC 60598-1, Luminaires Part 1: General requirements and tests IEC 60598-2-1, Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires IEC 60598-2-2, Luminaires Part 2: Particular requirements Section 2: Recessed luminaires