Tool Corp. Threading Vol. 1.1
Table of Contents: Imperial (Fractional) s: High Speed Steel Hand Taps Pages 3-5 General Purpose HSS Hand Taps Pages 3-4 Spiral Point HSS Hand Taps Page 4 Production Grade Pipe Taps Page 4 Spiral Fluted Point HSS Hand Taps Page 5 Combination Drill and Taps Page 5 Solid Carbide ThreadMills Page 6-7 UN (Unified Thread) ThreadMills Page 6 BSPP ThreadMills Page 7 BSPT ThreadMills Page 7 NPT ThreadMills Page 7 NPTF ThreadMills Page 7 Technical Information: Tap Drill Recommendations Page 8 Metric s: High Speed Steel Hand Taps Pages 9-11 General Purpose HSS Hand Taps Pages 9 Spiral Point HSS Hand Taps Page 9 Spiral Fluted Point HSS Hand Taps Page 10 Combination Drill and Taps Page 10 Solid Carbide ThreadMills Page 11 Standard Helical ThreadMills Page 11 Coolant Through ThreadMills Page 11 2 www.mastercuttool.com Tel: 1-727-726-5336
High Speed Steel Hand Taps Fractional All of our High Speed Steel Hand Taps are of the highest quality with a finish, ground threads, and right hand features. General Purpose HSS Hand Taps Limit Tapered Bottom Set of 3 0 80 H1 2 600100T 600100P 600100B 600100S 1 64 H1 2 600105T 600105P 600105B 600105S 1 72 H1 2 600110T 600110P 600110B 600110S 2 56 H2 3 600115T 600115P 600115B 600115S 2 64 H2 3 600120T 600120 P 600120 B 600120 S 3 48 H2 3 600125T 600125P 600125B 600125S 3 56 H2 3 600130T 600130P 600130B 600130S 4 36 H2 3 600135T 600135P 600135B 600135S 4 40 H2 3 600140T 600140P 600140B 600140S 4 48 H2 3 600145T 600145P 600145B 600145S 5 40 H2 3 600150T 600150P 600150B 600150S 5 44 H2 3 600155T 600155P 600155B 600155S 6 32 H3 3 600160T 600160P 600160B 600160S 6 40 H2 3 600165T 600165P 600165B 600165S 8 32 H3 4 600170T 600170P 600170B 600170S 8 36 H2 4 600175T 600175P 600175B 600175S 10 24 H3 4 600180T 600180P 600180B 600180S 10 32 H3 4 600185T 600185P 600185B 600185S 12 24 H3 4 600190T 600190P 600190B 600190S 12 28 H3 4 600195T 600195P 600195B 600195S 1/4 20 H3 4 600200T 600200P 600200B 600200S 1/4 28 H3 4 600205T 600205P 600205B 600205S 5/16 18 H3 4 600210T 600210P 600210B 600210S 5/16 24 H3 4 600215T 600215P 600215B 600215S 3/8 16 H3 4 600220T 600220P 600220B 600220S 3/8 24 H3 4 600225T 600225P 600225B 600225S 7/16 14 H3 4 600230T 600230P 600230B 600230S 7/16 20 H3 4 600235T 600235P 600235B 600235S 1/2 13 H3 4 600240T 600240P 600240B 600240S 1/2 20 H3 4 600245T 600245P 600245B 600245S 9/16 12 H3 4 600250T 600250P 600250B 600250S 9/16 18 H3 4 600255T 600255P 600255B 600255S 5/8 11 H3 4 600260T 600260P 600260B 600260S 5/8 18 H3 4 600265T 600265P 600265B 600265S 11/16 11 H3 4 600270T 600270P 600270B 600270S 11/16 16 H3 4 600275T 600275P 600275B 600275S 3/4 10 H3 4 600280T 600280P 600280B 600280S 3/4 16 H3 4 600285T 600285P 600285B 600285S 7/8 9 H4 4 600290T 600290P 600290B 600290S 7/8 14 H4 4 600295T 600295P 600295B 600295S 1 8 H4 4 600300T 600300P 600300B 600300S 1 12 H4 4 600305T 600305P 600305B 600305S 1 14 H4 4 600310T 600310P 600310B 600310S Fax: 1-727-725-2532 www.mastercuttool.com 3
High Speed Steel Hand Taps General Purpose HSS Hand Taps (Cont.d) Fractional 1-1/8 7 H4 4 600315T 600315P 600315B 600315S 1-1/8 12 H4 4 600320T 600320P 600320B 600320S 1-1/4 7 H4 4 600325T 600325P 600325B 600325S 1-1/4 12 H4 6 600330T 600330P 600330B 600330S 1-3/8 6 H4 4 600335T 600335P 600335B 600335S 1-3/8 12 H4 6 600340T 600340P 600340B 600340S 1-1/2 6 H4 4 600345T 600345P 600345B 600345S 1-1/2 12 H4 6 600350T 600350P 600350B 600350S 2 Spiral Point 3 Spiral Point 2 HSS Spiral Point Hand Taps for use on Steel Limit 0 80 H1 605000 1 64 H1 605005 1 72 H1 605010 2 56 H2 605015 2 64 H2 605020 3 48 H2 605025 3 56 H2 605030 4 36 H2 605035 4 40 H2 605040 4 48 H2 605045 5 40 H2 605050 5 44 H2 605055 6 32 H3 605060 6 40 H2 605065 8 32 H3 605070 8 36 H2 605075 10 24 H3 605080 10 32 H3 605085 12 24 H3 605090 12 28 H3 605095 1/4 20 H3 605100 1/4 28 H3 605105 5/16 18 H3 605110 5/16 24 H3 605115 3 HSS Spiral Point Hand Taps for use on Steel Limit 3/8 16 H3 605120 3/8 24 H3 605125 7/16 14 H3 605130 7/16 20 H3 605135 1/2 13 H3 605140 1/2 20 H3 605145 9/16 12 H3 605150 9/16 18 H3 605155 5/8 11 H3 605160 5/8 18 H3 605165 3/4 10 H3 605170 3/4 16 H3 605175 Production Grade Pipe Taps HSS Production Grade Pipe Hand Taps for Steel applications NPT NPTF 1/16 27 4 615000 615000F 1/8 27 4 615005 615005F 1/4 18 4 615010 615010F 3/8 18 4 615015 615015F 1/2 14 4 615020 615020F 3/4 14 5 615025 615025F 1 11-1/2 5 615030 615030F 1-1/4 11-1/2 5 615035 615035F 1-1/2 11-1/2 7 615040 615040F 2 11-1/2 7 615045 ~ 4 www.mastercuttool.com Tel: 1-727-726-5336
High Speed Steel Hand Taps Spiral Fluted Point Taps HSS Spiral Fluted Hand Taps with Ground Threads for use on Steel Limit Bottom 3 48 H2 2 610005P 610005B 4 40 H2 2 610010P 610010B 5 40 H2 2 610015P 610015B 6 32 H3 2 610020P 610020B 8 32 H3 3 610025P 610025B 10 24 H3 3 610030P 610030B 10 32 H3 3 610035P 610035B 12 24 H3 3 610040P 610040B 1/4 20 H3 3 610045P 610045B 1/4 28 H3 3 610050P 610050B 5/16 18 H3 3 610055P 610055B 5/16 24 H3 3 610060P 610060B 3/8 16 H3 3 610065P 610065B 3/8 24 H3 3 610070P 610070B 7/16 14 H3 3 610075P 610075B 7/16 20 H3 3 610080P 610080B 1/2 13 H3 3 610085P 610085B 1/2 20 H3 3 610090P 610090B Fractional Overall (OAL) of Square (Inches) Thread Drill Combination Drill and Taps HSS Combination Drill and Taps for Steel applications NC NF Overall Drill Drill Shank Diameter (SH) Square (Inches) Thread Square of Square Shank Dia 2 4 40 1 7/8 1/4 0.0910 3/8 3/16 0.110 0.141 620000 4 48 1 7/8 1/4 0.0945 3/8 3/16 0.110 0.141 620005 5 40 1 15/16 9/32 0.1040 13/32 3/16 0.110 0.141 620010 5 44 1 15/16 9/32 0.1060 13/32 3/16 0.110 0.141 620015 6 32 2 5/16 0.1115 7/16 3/16 0.110 0.141 620020 6 40 2 5/16 0.1170 7/16 3/16 0.110 0.141 620025 8 32 2 1/8 3/8 0.1375 1/2 1/4 0.131 0.168 620030 8 36 2 1/8 3/8 0.1405 1/2 1/4 0.131 0.168 620035 10 24 2 3/8 13/32 0.1545 5/8 1/4 0.152 0.194 620040 10 32 2 3/8 13/32 0.1635 5/8 1/4 0.152 0.194 620045 12 24 2 3/8 15/32 0.1805 21/32 9/32 0.165 0.220 620050 12 28 2 3/8 15/32 0.1860 21/32 9/32 0.165 0.220 620055 1/4 20 2 1/2 17/32 0.2080 25/32 5/16 0.191 0.255 620060 1/4 28 2 1/2 17/32 0.2200 25/32 5/16 0.191 0.255 620065 5/16 18 2 27/32 11/16 0.2660 15/16 3/8 0.238 0.318 620070 5/16 24 2 27/32 11/16 0.2770 15/16 3/8 0.238 0.318 620075 3/8 16 3 3/8 13/16 0.3225 1 1/16 7/16 0.286 0.381 620080 3/8 24 3 3/8 13/16 0.3395 1 1/16 7/16 0.286 0.381 620085 7/16 14 3 3/4 1 0.3770 1 1/4 13/32 0.242 0.323 620090 7/16 20 3 3/4 1 0.3955 1 1/4 13/32 0.242 0.323 620095 1/2 13 4 1/16 1 1/8 0.4350 1 3/8 7/16 0.275 0.367 620100 1/2 20 4 1/16 1 1/8 0.4580 1 3/8 7/16 0.275 0.367 620105 Drill (Inches) Fax: 1-727-725-2532 www.mastercuttool.com 5
Fractional Solid Carbide ThreadMills Overall (OAL) Lenth of Cut (LOC) Shank Diameter (SH) Cutting Diameter (DIA) UN (Unified Thread) ThreadMills Helical Multi-Helix 6 32.095x7/32x1/8x2 3 700-0001 700-1001 8 32.115x1/4x1/8x2 3 700-0002 700-1002 8 36.115x1/4x1/8x2 3 700-0003 700-1003 10 24.120x5/16x3/16x2 3 700-0004 700-1004 10 32.120x5/16x3/16x2 3 700-0005 700-1005 1/4 20.180x1/2x3/16x2-1/2 3 700-0006 700-1006 1/4 28.180x1/2x3/16x2-1/2 3 700-0007 700-1007 5/16 18.240x5/8x1/4x2-1/2 3 700-0008 700-1008 5/16 24.240x5/8x1/4x2-1/2 3 700-0009 700-1009 3/8 16.290x3/4x5/16x3 4 700-0010 700-1010 3/8 24.290x3/4x5/16x3 4 700-0011 700-1011 7/16 14.340x7/8x3/8x3 4 700-0012 700-1012 7/16 20.340x7/8x3/8x3 4 700-0013 700-1013 1/2 13.350x7/8x3/8x3-1/2 4 700-0014 700-1014 1/2 20.350x7/8x3/8x3-1/2 4 700-0015 700-1015 9/16 12.370x7/8x1/2x3-1/2 4 700-0016 700-1016 9/16 18.370x7/8x1/2x3-1/2 4 700-0017 700-1017 5/8 11.470x1-1/4x1/2x3-1/2 5 700-0018 700-1018 5/8 18.470x1-1/4x1/2x3-1/2 5 700-0019 700-1019 3/4 10.495x1-1/4x1/2x3-1/2 5 700-0020 700-1020 3/4 12.495x1-1/4x1/2x3-1/2 5 700-0021 700-1021 3/4 16.495x1-1/4x1/2x3-1/2 5 700-0022 700-1022 7/8 9.620x1-1/4x5/8x3-1/2 5 700-0023 700-1023 7/8 14.620x1-1/4x5/8x3-1/2 5 700-0024 700-1024 1 8.620x1-3/8x3/4x4 5 700-0025 700-1025 1 12.620x1-3/8x3/4x4 5 700-0026 700-1026 Coating options: is Mastercut Tool Corp s new proprietary coating that surpasses the proven performance of AlTiN for superior extreme machining results. With a thermal stability above 1,600 F (900 C) this coating excels in high speed dry machining applications. Harder than our original AlTiN by 1000 HV, with an increase in thermal stability of 200 F (100 C), will ensure that heat buildup, friction, and edge breakdown are all greatly reduced, resulting in better cutting performance and longer tool life. As with it s predecessor, will be an excellent coating for applications involving tough-to-cut tool steels, stainless, cast iron and non-ferrous material, and it can also be used very effectively for interrupted cuts. can be run at more aggressive speeds and feeds than other coatings, and can be run without coolant in specific applications. continues to be the coating of choice for tough-to-cut materials. Hardness: 3800 HV, Coating Thickness: 2-4 Microns, Thermal Stability: 1,650 F or 900 C. 6 www.mastercuttool.com Tel: 1-727-726-5336
Solid Carbide ThreadMills Fractional BSPP ThreadMills Helical Multi-Helix 1/16, 1/8 28.240x.572x1/4x2-1/2 3 700-2001 700-2501 1/4 19.312x.737x5/16x3 4 700-2002 700-2502 1/2 14.470x1.143x1/2x3-1/2 4 700-2003 700-2503 1 11.620x1.546x5/8x4 5 700-2004 700-2504 BSPT ThreadMills Helical Multi-Helix 1/16, 1/8 28.240x.401x1/4x2-1/2 3 700-3001 700-3501 1/4 19.312x.578x5/16x3 4 700-3002 700-3502 1/2 14.470x.785x1/2x3-1/2 4 700-3003 700-3503 1 11.620x1.546x5/8x4 5 700-3004 700-3504 NPT ThreadMills Helical Multi-Helix 1/16 27.245x7/16x1/4x2-1/2 3 700-4001 700-4501 1/8 27.310x7/16x5/16x2-1/2 4 700-4002 700-4502 1/4 18.305x5/8x3/8x3 4 700-4003 700-4503 3/8 18.305x5/8x3/8x3 4 700-4004 700-4504 1/2 14.495x7/8x1/2x3-1/2 4 700-4005 700-4505 3/4 14.495x7/8x1/2x3-1/2 4 700-4006 700-4506 1 11.620x1-1/8x3/4x4 5 700-4007 700-4507 NPTF ThreadMills Helical Multi-Helix 1/16 27.245x7/16x1/4x2-1/2 3 700-5001 700-5501 1/8 27.310x7/16x5/16x2-1/2 4 700-5002 700-5502 1/4 18.305x5/8x3/8x3 4 700-5003 700-5503 3/8 18.305x5/8x3/8x3 4 700-5004 700-5504 1/2 14.495x7/8x1/2x3-1/2 4 700-5005 700-5505 3/4 14.495x7/8x1/2x3-1/2 4 700-5006 700-5506 1 11.620x1-1/8x3/4x4 5 700-5007 700-5507 Fax: 1-727-725-2532 www.mastercuttool.com 7
8 Technical Information Tap Drill Recommendations Fractional s Metric s Drill Dec. Equiv 0 80 3/64.0469 1 64 53.0595 1 72 53.0595 2 56 50.0700 2 64 50.0700 3 48 47.0785 3 56 46.0810 4 36 45.0820 4 40 43.0890 4 48 42.0935 5 40 38.1015 5 44 37.1040 6 32 36.1065 6 40 33.1130 8 32 29.1360 8 36 29.1360 10 24 26.1470 10 32 21.1590 12 24 16.1770 12 28 15.1800 1/4 20 7.2010 1/4 28 3.2130 5/16 18 F.2570 5/16 24 I.2720 3/8 16 5/16.3125 3/8 24 Q.3320 7/16 14 U.3680 7/16 20 25/64.3906 1/2 13 27/64.4219 1/2 20 29/64.4531 9/16 12 31/64.4844 9/16 18 33/64.5156 5/8 11 17/32.5312 5/8 18 37/64.5781 11/16 11 19/32.5938 11/16 16 5/8.6250 3/4 10 21/32.6562 3/4 16 11/16.6875 7/8 9 49/64.7656 7/8 14 13/16.8125 1 8 7/8.8750 1 12 59/64.9219 1 14 59/64.9219 1-1/8 7 63/64.9844 1-1/8 12 1-3/64 1.0469 1-1/4 7 1-7/64 1.1094 1-1/4 12 1-11/64 1.1719 1-3/8 6 1-7/32 1.2188 1-3/8 12 1-19/64 1.2969 1-1/2 6 1-11/32 1.3438 1-1/2 12 1-27/64 1.4219 Drill Dec. Equiv (inches) M1.6 0.35 1.25.0492 M1.8 0.35 1.45.0571 M2 0.40 1.60.0630 M2.2 0.45 1.75.0689 M2.5 0.45 2.05.0807 M3 0.50 2.50.0984 M3.5 0.60 2.90.1142 M4 0.70 3.30.1299 M4.5 0.75 3.70.1476 M5 0.80 4.20.1654 M6 1.00 5.00.1969 M7 1.00 6.00.2362 M8 1.00 7.00.2756 M8 1.25 6.70.2638 M10 1.25 8.70.3425 M10 1.50 8.50.3346 M12 1.25 10.80.4252 M12 1.75 10.20.4016 M14 1.50 12.50.4921 M14 2.00 12.00.4724 M16 1.50 14.50.5709 M16 2.00 14.00.5512 M18 1.50 16.50.6496 M18 2.50 15.50.6102 M20 1.50 18.50.7283 M20 2.50 17.50.6890 M22 1.50 20.50.8071 M22 2.50 19.50.7677 M24 2.00 22.00.8661 M24 3.00 21.00.8268 Pipe Tap s www.mastercuttool.com Tel: 1-727-726-5336 Without Reamer Drill With Reamer 1/16 27 C (.242) A (.234) 1/8 27 Q (.332) 21/64 1/4 18 7/16 27/64 3/8 18 9/16 9/16 1/2 14 45/64 11/16 3/4 14 29/32 57/64 1 11-1/2 1-9/64 1-1/8 1-1/4 11-1/2 1-31/64 1-15/32 1-1/2 11-1/2 1-23/32 1-45/64 2 11-1/2 2-3/16 2-11/64
Metric High Speed Steel Hand Taps Metric General Purpose HSS Hand Taps (MM) Limit Tapered Bottom Set of 3 M1.6 0.35 D3 2 600355T 600355P 600355B 600355S M2 0.40 D3 3 600360T 600360P 600360B 600360S M2.5 0.45 D3 3 600365T 600365P 600365B 600365S M3 0.50 D3 3 600370T 600370P 600370B 600370S M3.5 0.60 D4 3 600375T 600375P 600375B 600375S M4 0.70 D4 4 600380T 600380P 600380B 600380S M5 0.80 D4 4 600385T 600385P 600385B 600385S M6 1.00 D5 4 600390T 600390P 600390B 600390S M7 1.00 D5 4 600395T 600395P 600395B 600395S M8 1.00 D5 4 600400T 600400P 600400B 600400S M8 1.25 D5 4 600405T 600405P 600405B 600405S M10 1.25 D5 4 600410T 600410P 600410B 600410S M10 1.50 D6 4 600415T 600415P 600415B 600415S M12 1.25 D6 4 600420T 600420P 600420B 600420S M12 1.75 D6 4 600425T 600425P 600425B 600425S M14 1.50 D6 4 600430T 600430P 600430B 600430S M14 2.00 D7 4 600435T 600435P 600435B 600435S M16 1.50 D6 4 600440T 600440P 600440B 600440S M16 2.00 D7 4 600445T 600445P 600445B 600445S M18 1.50 D6 4 600450T 600450P 600450B 600450S M18 2.50 D7 4 600455T 600455P 600455B 600455S M20 1.50 D6 4 600460T 600460P 600460B 600460S M20 2.50 D7 4 600465T 600465P 600465B 600465S M22 1.50 D6 4 600470T 600470P 600470B 600470S M22 2.50 D7 4 600475T 600475P 600475B 600475S M24 2.00 D7 4 600480T 600480P 600480B 600480S M24 3.00 D8 4 600485T 600485P 600485B 600485S 2 Spiral Point 3 Spiral Point 2 HSS Spiral Point Hand Taps for use on Steel (MM) Limit M2 0.40 D3 605180 M2.5 0.45 D3 605185 M3 0.50 D3 605190 M3.5 0.60 D4 605195 M4 0.70 D4 605200 M5 0.80 D4 605205 M6 1.00 D5 605210 M7 1.00 D5 605215 M8 1.25 D5 605220 3 HSS Spiral Point Hand Taps for use on Steel Fax: 1-727-725-2532 www.mastercuttool.com 9 (MM) Limit M10 1.50 D6 605225 M12 1.75 D6 605230 M14 2.00 D7 605235 M16 2.00 D7 605240 M18 2.50 D7 605245 M20 2.50 D7 605250
Metric Metric High Speed Steel Hand Taps Spiral Fluted Point Taps HSS Spiral Fluted Hand Taps with Ground Threads for use on Steel Limit Bottom M3 0.50 D3 2 610095P 610095B M3.5 0.60 D4 2 610100P 610100B M4 0.70 D4 3 610105P 610105B M5 0.80 D4 3 610110P 610110B M6 1.00 D5 3 610115P 610115B M8 1.25 D5 3 610120P 610120B M10 1.50 D6 3 610125P 610125B M12 1.75 D6 3 610130P 610130B Overall (OAL) of Square (Inches) Thread Drill Shank Diameter (SH) Drill (Inches) Square (Inches) Combination Drill and Taps HSS Combination Drill and Taps for Steel applications (MM) Overall Drill Drill Thread Square of Square Shank Dia 2 M4 0.70 2-1/8 3/8 0.1340 1/2 1/4 0.131 0.168 620500 M5 0.80 2-3/8 13/32 0.1700 5/8 1/4 0.152 0.194 620505 M6 1.00 2-1/2 17/32 0.2030 25/32 5/16 0.191 0.255 620510 M8 1.25 2-27/32 11/16 0.2730 15/16 3/8 0.238 0.318 620515 M10 1.50 3.375 13/16 0.3440 0.6875 7/16 0.286 0.381 620520 M12 1.75 4-1/16 1 1/8 0.4140 1 3/8 7/16 0.275 0.367 620525 10 www.mastercuttool.com Tel: 1-727-726-5336
Metric Solid Carbide ThreadMills Metric Standard Helical ThreadMills (MM) Helical M4 0.70 2.8x8.4x4x51 3 701-3501 M5 0.80 3.5x10.4x4x51 3 701-3502 M6 1.00 3.9x12x4x51 3 701-3503 M8 0.75 5.9x16x6x58 3 701-3504 M8 1.00 5.9x16x6x58 3 701-3505 M8 1.25 5.9x16.25x6x58 3 701-3506 M10 1.25 7.7x20x8x64 4 701-3507 M10 1.50 7.7x21x8x64 4 701-3508 M12 1.00 9.9x24x10x73 4 701-3509 M12 1.50 9.4x24x10x73 4 701-3510 M12 1.75 8.7x24.5x10x73 4 701-3511 M14 1.50 11.2x28.5x12x84 4 701-3512 M16 2.00 11.9x32x12x84 5 701-3513 M18 2.50 13.9x40x16x93 5 701-3514 M20, M24 3.00 15.9x42x16x93 5 701-3515 Coolant Through ThreadMills (MM) Single Hole Straight Multi-Hole Side M6 1.00 4.5x13x6x58 3 701-4001 701-4501 3 M8 0.75 5.9x17.5x6x65 3 701-4002 701-4502 3 M8 1.00 5.9x17.5x6x65 3 701-4003 701-4503 3 M8 1.25 5.9x17.5x6x65 3 701-4004 701-4504 3 M10 1.25 7.5x21x8x72 4 701-4005 701-4505 4 M10 1.50 7.5x21x8x72 4 701-4006 701-4506 4 M12 1.00 9.5x24x10x73 4 701-4007 701-4507 4 M12 1.50 9.5x26.25x10x80 4 701-4008 701-4508 4 M12 1.75 9.5x26.25x10x80 4 701-4009 701-4509 4 M14 1.50 11.9x34x12x84 4 701-4010 701-4510 4 M16 2.00 11.9x34x12x84 5 701-4011 701-4511 5 M18 2.50 13.9x40x16x93 5 701-4012 701-4512 5 M20, M24 3.00 15.9x42x16x93 5 701-4013 701-4513 5 Num. of Holes Coating options: is Mastercut Tool Corp s new proprietary coating that surpasses the proven performance of AlTiN for superior extreme machining results. With a thermal stability above 1,600 F (900 C) this coating excels in high speed dry machining applications. Harder than our original AlTiN by 1000 HV, with an increase in thermal stability of 200 F (100 C), will ensure that heat buildup, friction, and edge breakdown are all greatly reduced, resulting in better cutting performance and longer tool life. As with it s predecessor, will be an excellent coating for applications involving tough-to-cut tool steels, stainless, cast iron and non-ferrous material, and it can also be used very effectively for interrupted cuts. can be run at more aggressive speeds and feeds than other coatings, and can be run without coolant in specific applications. continues to be the coating of choice for tough-to-cut materials. Hardness: 3800 HV, Coating Thickness: 2-4 Microns, Thermal Stability: 1,650 F or 900 C. Fax: 1-727-725-2532 www.mastercuttool.com 11
Don t Forget to Check Out All That Mastercut Has to Offer Mastercut Tool Corp. offers a full line of solid carbide cutting tools, both standards and special requests. Whether you are cutting wood, exotic metals, acrylic, or any other material, Mastercut has an ideal solution for all of your cutting tool needs. We can also sharpen your dull cutters, regardless of manufacturer. Call or E-mail us for more information. www.mastercuttool.com American Made, World Class Quality Wholesale and Dealer Discounts Available Proudly distributed by: Mastercut Tool Corp. 965 F. Harbor Lake Drive Safety Harbor, FL 34695 USA Telephone (727) 726-5336 Fax (727) 725-2532 sales@mastercuttool.com 105 12 www.mastercuttool.com Tel: 1-727-726-5336 02-2011-MFU-Vol-1.1