DIESEL-FUELED, BLOWN AIR, DUCTABLE HEATERS Electronic thermostatically controlled Low power consumption Compact space saving size Short heat-up times Dehumidification of the cabin Quiet when running Combustion Exhausted Externally SET THE DESIRED TEMPERATURE THE REST IS AUTOMATIC Model AT2000ST (2 Kw) AT3900(3.9 Kw) Voltage 12V, 24V Optional 12V, 24V Optional Heat output Min. 0.9 Kw, Max. 2.0 Kw Min. 1.5 Kw, Max. 3.9 kw Diesel Consumption Min. 0.12 L/Hr, Max. 0.24 L/Hr Min. 00.17 L/Hr, Max. 0.42 L/Hr Power Consumption Min. 14 W/Hr, Max. 29 W/Hr Min.16 W/Hr, Max. 40 W/Hr Dimensions 311 x 120 x 121mm 423 x 148 x 162mm Weight 2.6 Kg 5.9Kg 041087 AT2000ST 1 Outlet Accessories Kit: Floor mount heater bracket x 1, 60mm ducting x 1 mtr, Duct Clamp 47-70mm x 3, Air Outlet, 45 x 1, Hose connector for outlet x 1, Vent 60mm flat open x 1. 041088 AT2000ST 2 Outlets Accessories Kit: Floor mount heater bracket x 1, 60mm ducting x 2 mtr, Duct Clamp 47-70mm x 7, Air Outlet, 45 x 1, Air outlet closable x 1, Hose connector for outlet x 2, Vent 60mm flat open x 1, Branch pipe 60x60x60mm x 1. Motorhome, Caravan, Horse Truck PART NUMBER 000527 (AT3900) Heater Only DESCRIPTION 3.9KW RV HEATER Marine, Launch, Yacht Both Outlet Kits Include: AT2000ST Heater, Dosing Pump, Heater harness standard, Fuel Pump harness (7m), Rotary Control, Exhaust pipe + cap (0.8m), Fuel Standpipe, Comb. duct + cap (0.5m) Exhaust Muffler, Exhaust Cl. x 2, Fuel line 6mtr, Bits bag + accessories. PART NUMBER 000520 (AT2000M) 000530 (AT3900M) DESCRIPTION 2KW MARINE HEATER 3.9KW MARINE HEATER Marine Installation Kit includes: Metering pump bracket (sound-deadened), metering pump, exhaust outlet, intake silencer (for Air Top 3900), Exhaust silencer for boats, Heater bracket for boats, Grille (already mounted on Air Top 2000S), Control, External temperature sensor (5m/20m), Fuel tank tap, Faceplate with ventilation switch (Air Top 3900 3-1
Webasto Ducting and Accessories Y JUNCTION 002789 (SA2479) 90 x 80 x 80mm 002770 (SA2468) 80 x 80 x 80mm 002809 (SA2488) 60 x 60 x 60mm ADAPTOR RINGS Steps outlets and junctions up to adapt larger ducting 002780 (SA2473A) 70mm>80mm 002782 (SA2474A) 55mm>60mm 90 ELBOW Direct off AT2000 heater 002784 (SA2476) 60mm Elbow MUFFLER SILENCER KIT Includes 2x hose clamps 002796 (SA2483) AT2000 002797 (SA2483A) AT3900 HEATER REDUCER Reduces heater outlet to accept smaller ducting, direct onto heater. 002773 (SA2469A) AT3900 to 80mm DUCTING REDUCER Reduce 90mm ducting to adapt 80mm 002772 (SA2469) 90mm>80mm Duct Re- T JUNCTION 002783 (SA2475) 60 x 60 x 60mm OUTLET VENTS 002792 (SA2480A) 60mm Open 002822 (SA2494) 60mm Closeable 002779 (SA2473) 70mm Closeable 002777 (SA2472) 80mm Open 002791 (SA2480) 90mm Open 45 OUTLET VENTS 002765 (SA2461A) 55mm Open/45 002778 (SA2472A) 80mm Open/45 EXTERNAL THERMOSTAT 002793 (SA2481) External Thermostat AT2000 002794 (SA2482) External Thermostat AT3900 DUCTING 002767 (SA2465) 60mm 002768 (SA2466) 80mm 002769 (SA2467) 90mm OTHER WEBASTO COMPONENTS REPLACEMENT FUEL FILTER 001471 (SA14038) AT2000 / AT3900 L SHAPE MOUNTING BRACKET 002787 (SA2478) AT2000 / AT3900 FUEL STANDPIPE (Replaces T ) 002807 (SA2486) AT2000 / AT3900 EXHAUST LAGGING 002817 (SA2490-005) Marine Exhaust Only 3-2
Quiet thermostatic operation Stainless steel burner and heat-exchanger with clean combustion gives maintenance free durability Low power consumption Compact and easy to install High quality motor with ball race bearings Advanced micro-processor electronics Self diagnostic fault finding system Fully CE compliant and tested to the latest European standards Fast warm-up time Reduces condensation All Models this page Energy Safety Compliance # SER2866A 002577 (SA1964) 002567 (SA1956) SPECIFICATIONS 2 KW HEATER 2.8 KW HEATER Heat Input 2.1kw 3.0kw Heat Output 1.9kw 2.8kw Voltage 12v 12v Power consumption 1.4A continuous 1.9A continuous Air Throughput 60 C.F.M 85 C.F.M Fuel LPG/Butane/Prop. LPG/Butane/Prop. Length (mm) 320 415 Width (mm) 172 210 Height (mm) 100 120 INCLUDES: 2 KW 2.8 KW SA1964 Thermostat SA1956 Exhaust 750mm 750mm Air Inlet 750mm 750mm Inlet Vent Ducting 1m (60mm) 2m (80mm) Outlet Vent Ducting Accessories Part Description Size 002574 SA1961 002575 SA1962 002578 SA1965 002579 SA1966 Y Junction for SA1956* *Requires 3x SA1962 Reducer for y t/s SA1956 OPEN Outlet Vent t/s SA1956 80 mm Reducer for Vent t/s SA1964 Marine Kit Available For Fresh Water Only: Includes: 3m (60mm) ducting, 1x 60mm Vent, 1x 80mm Vent and 80-60mm Reducer, 2 S/S mounting brackets, 1 S/S Skin fitting, Marine heater vent, 2x Wiring extensions, Fuse kit and additional hose clamps. 002566 (SA1955) Marine Kit 80 x 80 x 80 mm 80 to 60 mm Wiring 3-3
ATWOOD BLOWN AIR HEATER - RV The Everest Star 2 series features an electric shut-off on the gas valve. A new blower assembly that increases air delivery by 60% and electronic ignition (no standing pilot). Weight is just 10.4Kg. Heat output for SA454 is front discharge only, SA1454 discharge from both side ducts, or a combination of front and side ducts. Energy Safety Compliance # SER2868 MODEL 003486 (SA454K) 001728 (SA1454K) INPUT BTU/hr GAS TYPE ELECTRONIC IGNITION VOLTS D.C AMPS DRAW DIMENSIONS W x H x L mm 12,000 LPG YES 12 1.8 213 x 289 x 524 12,000 LPG YES 12 3.4 213 x 289 x 524 12,000 BTU = 3.5 Kw 3-4
ATWOOD RV WATER HEATERS Atwood water heaters are engineered with an extended cold water inlet tube which prevents early mixing of cold and hot water. More hot water is available before the temperature drops off - up to 55% longer for 6 gallon models. Atwood heaters use an aluminium alloy U-tube combustion chamber to conduct heat more quickly and reduce weight. Heat exchanger option uses otherwise wasted heat in motorized units to provide heat. The aluminium clad tank eliminates the necessity of an anode rod. Storage tanks are 100% pressure tested under water and are fully fire-checked before leaving the plant. Maximum water pressure 45 PSI. 6 Gal (22Ltr) A=406mm B=317mm C=419mm D=457mm 003391 (SA425N) 22L Gas/230V, remote ignition NEW Door Flush Mounting Flange 002749 (SA2440-002) 22litre Atwood Exterior Trim Energy Safety Compliance # SER5684B GAS QUIP - STORAGE WATER HEATER FOR RVS Maximum supply pressure 20P.S.I. Tank capacity 13.5 litres. Weight when empty 9.3Kg. Unit is to be installed with a Low Pressure Pump or Pressure Reducing Valve set at 20PSI, both sold separately (002633 (SA2119LP) Shurflo 10.6 l/min 20PSI) (001443 (SA14000) Pressure Reducing Valve set to 20PSI) Height 250mm Width 285mm Depth 520mm 002317 (SA1750) Gas only 002318 (SA1751) Gas/230V Energy Safety Compliance # SER5462 3-5
Marine and RV Water Storage Heaters 2 WAY HEAT EXCHANGE AND 230V STAINLESS STEEL TANK 30lt. No Longer Available All models grant high performances and efficiency being equipped with the following components: 1) 316 Stainless Steel Tank 2) 316 Stainless Steel Heat Exchanger: Its large exchange surface allows a huge production of hot water exploiting at best the heat of the cooling water coming from the boat engine (even with very small temperature differences). 3) Electrical Heater Element: Equipped with an adjustable and safety thermostat, allows hot water production even when the boat engine is off. 4) Insulation: A thick foam of expanded polyurethane with closed cells reduces heat loss to 1 per hour within 24 hours. 5) External Casing: Stainless Steel resistant to salt water 6) Stainless Steel Mounting Brackets: They ensure a strong, stable and easy installation. 7) Safety Valve: Protecting the tank from excessive pressure (Pressure relief / Non return valve). Internal View Part Number 001463 (SA14028) 001456 (SA1401S) 003491 (SA458S) Capacity (litres) Diameter Length Width 12 320mm 405mm N/A 22 320 475 N/A 45 320 880 N/A 001528 (SA1409V) Tempering Valve Required 001503 (SA1407) Anode (for Non S/S models) 001514 (SA14085) Element 1200W S/S 001480 (SA1405) Element 1200w 003857 (SA859) 3/8 Relief Valve 003858 (SA859N) 1/2 Relief Valve 3-6
Air-Conditioning KINGFISHER Electrical rating 240V 50Hz Cooling unit 2.5Kw Heat output 2.5Kw Maximum rated current Cooling 4.7A Heating 4.7A Air delivery maximum 160L/sec Installed weight 48 Kg Unit Dimensions: Facia Panel: Height 590mm Height 610mm Width 470mm Width 520mm Depth 530mm Fully remote controlled, enabling you to control your environment no matter what the conditions. With the electronic display, you can set your own temperature and have it displayed on the LCD screen with the touch of a button. 000950 (SA1010-01) HERON 2.2 Electrical rating 240V 50Hz Cooling unit 2.2Kw Heat output 1.5Kw Maximum rated current Cooling 4.0A Heating 6.5A Max. Locked rotor current 19A Air delivery maximum 110L/sec Installed weight 34 Kg Max. recommended area 26M3 Air handler Condenser Height 220mm Height 235mm Width 385mm Width 460mm Depth 230mm Depth 440mm Note: For installation of Air Handler allow 70mm in addition to height to allow for correct drainage. Allow minimum 70mm in addition to depth shown for sufficient air flow. 000957 (SA1020-001) 3-7
IBIS Roof Top Air Conditioner The IBIS reverse cycle heat pump roof top air conditioner has been extraordinarily built with a height of only 220mm. The IBIS provides both heating and cooling as well as filtered and dehumidified air. Features: - Light Weight for its Capacity - Ultra low profile ensures less drag when vehicle is Travelling. Greater clearance under over hanging obstacles - Less shadowing of Solar Panels etc - Flip down electronic controls make it easy to set the various functions - Supplied complete with a slimline remote control you can adjust your comfort level anywhere throughout your RV - Removable air filters - for quick servicing 000948 (SA1010-004) IBIS Air Conditioner Specifications Electrical rating (single phase) Nominal cooling capacity Nominal heating capacity Maximum rated current: cooling Maximum rated current: heating Maximum L/R current Air delivery maximum Installed weight (including plenum) IBIS 230-240v, 50Hz 3.2 Kw 3.2 Kw 5.1 A 5.0 A 20 A 140 l/s 45kg Dimensions Overall height Overall width Overall depth Air-discharge plenum height Air-discharge plenum width Air-discharge plenum length 220mm 825mm 1040mm 65mm 555mm 535mm SPARROW Roof Top Air Conditioner The SPARROW is a fully featured, lightweight (30kg), low profile 2kW rooftop air conditioner. It shares the same attractive indoor Plenum as the Ibis. Noise levels are very low, and being designed for Australia s harsh environment and scorching summers, the Sparrow creates a comfortable indoor environment quietly and efficiently. A true reverse cycle unit, the Sparrow provides up to 70% more heat for less power input than electric element type heaters. It is also worth noting that the Sparrow, along with ALL the reverse cycle air conditioners in the Aircommand range, has electronic defrost for low ambient operation, ie. NO low ambient cut out! Heat is provided even down to sub-zero outdoor temperatures, providing true year round comfort. 000949 (SA1010-005) Sparrow 2kW Reverse Cycle: L970 x W620 x H215 3-8
Air Conditioners DENSO CARAVAN AIR CONDITIONING KEY FEATURES: Reverse cycle refrigerative cooling and heating. Unobtrusive slim-line design. Remote controlled. Multi-speed interior and exterior fans Ultra-low fan speed for quiet operation. Easy installation for reduced cost. Floor mounted unit - ideal for pop-tops and caravans. Flexible mounting options and locations throughout the caravans. Australian designed and built using quality components providing extended trouble free operation and reducing ownership costs. Certified to Australian Standard AS-NZ 60335 The Denso UB1 air-conditioner is designed for use in recreational vehicles, especially pop-top and fixed roof caravans. As a general guide, air-conditioning performance will be acceptable in fixed roof recreational vehicles up to 7.0m in length, assuming that all walls and roof are insulated with insulation thickness of at least 25mm. Larger recreational vehicles including caravans and pop-tops with large canvas area and poorly insulated recreational vehicles will limit the ability of the air-conditioner to achieve comfortable interior temperatures in extreme weather. This Denso UB1 is designed to be operated on 230-240V 50Hz power from the electricity grid or a sine wave inverter equipped generator. The recommended generator capacity for this unit is 2.8kVA. The UB1 is specially designed for ease of installation and does not require the services of an electrician or refrigerant mechanic as the unit can be plugged directly into a 240V socket and comes pre-gassed. 040951 UB1 Air Conditioner Unit (Installation kit not included) 040952 3m Installation Kit includes wire harness and duct. 040953 6m Installation Kit includes wire harness and duct. Cooling Unit Dimensions: 912mmW x 450mm D x 267mm H SPECIFICATIONS: Nominal Capacity: 3.2kW Typical Cooling Capacity: 2.6kW Typical Heating Capacity: 2.0kW Weight: 44kg Power Supply: 230-240V, 50Hz Maximum Rated Current: 8A Airflow Volume: 360 m³/h Refrigerant Amount: 750g Max Operating Incline: 8 Operating Temp Range 16-45 C (Cooling) 0-25 C (Heating) * Indoor Noise Level: 48.8-62.1 db ** Pillow Noise Level: 52.3dB ***Outdoor Noise Level: 58.1-63.3dB Air Distribution Unit Dimensions: 492mm W x 220mm D x 70mm H Slim design with minimal space required. Fully adjustable louvres to direct airflow Remote Control Has a range of 8m with a quick cool function and timer. Made from tough ABS plastic * Indoor Noise - low and high fan settings ** Pillow Noise - low fan settings ***Outdoor Noise - low and high fan settings Duct Heavy duty construction with the flexibility to fit around and in the back of cupboards. 127mm clearance required to install duct. 3-9