M420/422 Electromagnetic Locks System Components M420/422 Mag Lock Overview The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application. All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M420 is tested and certified to meet or exceed UL1034 and BHMA 500lb. hold force requirements. The M420 electromagnetic lock comes in two configurations to meet your specific security needs. The M420 provides basic security, while the M420P provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M420P. Kits are available for top jam, double door, and glass door applications. Features and Benefits Bayonet mount makes installation simpler by not requiring magnet to be held overhead while mounting screws are installed New design allows for RH/LH configuration in the field Armature mount allows armature to pivot compensating for slight opening imperfections Limited Lifetime Warranty UL1034 Burglary-Resistant Electronic Locking Mechanisms, UL10C Positive Pressure Fire Tests of Door Assemblies and ANSI/BHMA Grade 1 certifications 500 lb. Hold Force See page 2 for additional features and options
ADDITIONAL FEATURES M420/M422 Automatic Voltage Selection (AVS) senses the voltage applied to the lock and responds accordingly M420P/M422P Magnetic Bond Sensor (MBS) monitors the strength of the bond between the lock and armature so you know the door is secure Door Position Switch (DPS) monitors whether the door is open or closed Relock Time Delay (RTD) provides a relock delay that is adjustable from 0.5 to 30 seconds Optional (P models only) Anti-Tamper Switch (ATS) provides an indication that the cover of the magnet is securely fastened to the lock and that the on board circuitry is secure MBS Indicator (LED) provides visual indication of magnetic bond at the lock M420/M422 Electromagnetic Lock Specifications Specification M420/M420P M422/M422P Holding Force Input Voltage (Standard Unit) Current Draw (Amps Standard Unit) Automatic Dual Voltage standard of 500 lbs..75a @ 12 VDC.38A @ 24 VDC Height 2-1/2" 2-1/2" standard of 500 lbs. 1.5A @ 12 VDC.76A @ 24 VDC Length 9" 18-1/16" Width 1-3/8" 1-3/8 Weight (approximate) 6 lbs. 12 lbs. Certifications UL1034, UL10C, ANSI/BHMA156.23 Temperature 0º-49º C (32º-120º F) Wire Gauge 14-22 AWG OPTIONS (for all) Herculite Door Bracket Top Jamb (inswinging doors) Filler Plates and Angle Brackets Specifications M420 M422 Length 10-1/2" 20-5/8" Filler Plates Width x Height 1-1/4" x 1/8" 4201F 4221F 1-1/4" x 1/4" 4202F 4222F 1-1/4" x 3/8" 4203F 4223F 1-1/4" x 1/2" 4204F 4224F 1-1/4" x 5/8" 4205F 4225F 3/4" x 1/2" 4206F 4226F 3/4" x 5/8" 4207F 4227F 3/4" x 3/4" 4208F 4228F Angle Brackets Width x Height Plate No. Plate No. 1"x1" 4201A 4221A 1-1/2" x 1" 4202A 4222A 1-1/2" x 1-1/2" 4203A 4223A 1-1/2" x 2" 4204A 4224A 1-1/2" x 2-1/2" 4205A 4225A 877-671-7011 schlage.com 2011 Ingersoll Rand 004206 10/11
M450/452 Electromagnetic Locks System Components M450/452 Mag Lock Overview The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application. All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M450 is tested and certified to meet or exceed UL1034 and BHMA 1000lb. hold force requirements. Features and Benefits Bayonet mount makes installation simpler by not requiring magnet to be held overhead while mounting screws are installed New design allows for RH/LH configuration in the field Armature mount allows armature to pivot compensating for slight opening imperfections Limited Lifetime Warranty UL1034 and BHMA Grade1 certified 1000 lb. Hold Force See page 2 for additional features and options The M450 electromagnetic lock comes in two configurations to meet your specific security needs. The M450 provides basic security, while the M450P provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M450P. Kits are available for top jam, double door, and glass door applications.
ADDITIONAL FEATURES M450/M452 Automatic Voltage Selection (AVS) senses the voltage applied to the lock and responds accordingly M450P/M452P Magnetic Bond Sensor (MBS) monitors the strength of the bond between the lock and armature so you know the door is secure Door Position Switch (DPS) monitors whether the door is open or closed Relock Time Delay (RTD) provides a relock delay that is adjustable from 0.5 to 30 seconds Optional (P models only) Anti-Tamper Switch (ATS) provides an indication that the cover of the magnet is securely fastened to the lock and that the on board circuitry is secure MBS Indicator (LED) provides visual indication of magnetic bond at the lock M450/M452 Electromagnetic Lock Specifications Specification M450/M450P M452/M452P Holding Force Input Voltage (Standard Unit) Current Draw (Amps Standard Unit) Automatic Dual Voltage standard of 1000 lbs..75a @ 12 VDC.38A @ 24 VDC Height 3" 3" 1000 lbs. per door leaf 1.5A @ 12 VDC.75A @ 24 VDC Length 10-1/4" 20-9/16" Width 1-3/4" 1-3/4" Weight (approximate) 10 lbs. 20 lbs. Certifications UL1034, UL10C, ANSI/BHMA156.23 Temperature 0º-49º C (32º-120º F) Wire Gauge 14-22 AWG OPTIONS (for all) Herculite Door Bracket Top Jamb (inswinging doors) Filler Plates and Angle Brackets Specifications M450 M452 Length 10-1/2" 20-5/8" Filler Plates Width x Height 1-1/4" x 1/8" 4501F 4521F 1-1/4" x 1/4" 4502F 4522F 1-1/4" x 3/8" 4503F 4523F 1-1/4" x 1/2" 4504F 4524F 1-1/4" x 5/8" 4505F 4525F 3/4" x 1/2" 4506F 4526F 3/4" x 5/8" 4507F 4527F 3/4" x 3/4" 4508F 4528F Angle Brackets Width x Height Plate No. Plate No. 1"x1" 4501A 4521A 1-1/2" x 1" 4502A 4522A 1-1/2" x 1-1/2" 4503A 4523A 1-1/2" x 2" 4504A 4524A 1-1/2" x 2-1/2" 4505A 4525A 877-671-7011 schlage.com 2011 Ingersoll Rand ES-5905 07/11
M490/492 Electromagnetic Locks System Components M490/492 Mag Lock Overview The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application. All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M490 is tested and certified to meet or exceed UL1034 and BHMA 1500lb. hold force requirements. Features and Benefits Bayonet mount makes installation simpler by not requiring magnet to be held overhead while mounting screws are installed New design allows for RH/LH configuration in the field Armature mount allows armature to pivot compensating for slight opening imperfections Limited Lifetime Warranty UL1034 Burglary-Resistant Electronic Locking Mechanisms, UL10C Positive Pressure Fire Tests of Door Assemblies and ANSI/BHMA Grade 1 certifications 1500 lb. Hold Force See page 2 for additional features and options The M490 electromagnetic lock comes in two configurations to meet your specific security needs. The M490 provides basic security, while the M490P provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M490P. Kits are available for top jam, double door, and glass door applications.
ADDITIONAL FEATURES M490/M492 Automatic Voltage Selection (AVS) senses the voltage applied to the lock and responds accordingly M490P/M492P Magnetic Bond Sensor (MBS) monitors the strength of the bond between the lock and armature so you know the door is secure Door Position Switch (DPS) monitors whether the door is open or closed Relock Time Delay (RTD) provides a relock delay that is adjustable from 0.5 to 30 seconds Optional Anti-Tamper Switch (ATS) provides an indication that the cover of the magnet is securely fastened to the lock and that the on board circuitry is secure MBS Indicator (LED) provides visual indication of magnetic bond at the lock M490/M492 Electromagnetic Lock Specifications Specification M490/M490P M492/M492P Holding Force Input Voltage (Standard Unit) Current Draw (Amps Standard Unit) Automatic Dual Voltage standard of 1500 lbs..65a @ 12 VDC.35A @ 24 VDC Height 3" 3" standard of 1500 lbs. 1.3A @ 12 VDC.7A @ 12 VDC Length 12-1/2" 25-1/16" Width 1-3/4" 1-3/4" Weight (approximate) 14 lbs. 28 lbs. Certifications UL 294, UL10C, ANSI/BHMA A156.23 Temperature 0º-49º C (32º-120º F) Wire Gauge 14-22 AWG OPTIONS (for all) Herculite Door Bracket Top Jamb (inswinging doors) Filler Plates and Angle Brackets Specifications M490 M492 Length 10-1/2" 20-5/8" Filler Plates Width x Height 1-1/4" x 1/8" 4901F 4921F 1-1/4" x 1/4" 4902F 4922F 1-1/4" x 3/8" 4903F 4923F 1-1/4" x 1/2" 4904F 4924F 1-1/4" x 5/8" 4905F 4925F 3/4" x 1/2" 4906F 4926F 3/4" x 5/8" 4907F 4927F 3/4" x 3/4" 4908F 4928F Angle Brackets Width x Height Plate No. Plate No. 1"x1" 4901A 4921A 1-1/2" x 1" 4902A 4922A 1-1/2" x 1-1/2" 4903A 4923A 1-1/2" x 2" 4904A 4924A 1-1/2" x 2-1/2" 4905A 4925A 877-671-7011 schlage.com 2011 Ingersoll Rand 004204 10/11