Electronics Differential Type 58A... The differential charge amplifier is used for signal conversion of piezoelectric sensors with differential output. Executions Aluminum die-cast enclosure (IP64) Plastic DIN-Rail enclosure (IP0) Signal Output Options Voltage Out Single Ended ±0 V; 5 ±5 V Voltage Out Differential ±0 V -Wire Current 4 ±6 ma Very large charge conversion range 0 400 V/pC 6 40 μa/pc Selectable high- and low pass filters Electrical connections Execution in aluminum enclosure: Connectors or cable glands Execution in plastic DIN-Rail enclosure: Screw terminals Suitable for ground isolated measuring chains Fig. : ä Differential charge amplifier in aluminum die-cast enclosure, Type 58AA 585A_00-7e-0.6 Description The differential charge amplifier is available in two enclosure executions and various voltage- and current output versions. Type 58A... has a selectable charge conversion factor (sensitivity) which is factory set and contains no reset-function but a high-pass filter (time constant) at the input stage. An internal compensation circuit eliminates the drift of the amplifier and compensates low frequency error-currents up to 5 na. The 8 0 VDC supply voltage is galvanically separated which prevents ground loop issues. Fig. : EMC Standards EN 6000-6- EN 6000-6- Product Standard Emitted interference Interference Immunity EN66- (class A and B) ä Differential charge amplifier in plastic DIN-Rail enclosure, Type 58AB Page /0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Technical Data Output Configuration Single Ended voltage ±0 V Single Ended voltage 5 ±5 V Differential voltage ±0 V -wire current 4 ±6 ma Supply Supply Voltage VDC 8... 0 8... 0 8... 0 8... 0 Galvanic Separation yes yes yes no Power Consumption (without load) ma 5 5 5 5 Output signal nominal FS V ±0 5 ±5 ±0 ma 4 ±6 Sensitivity mv/pc 0,5... 4 000 0,5... 000 0,5... 4 000 μa/pc 6... 40 Sensitivity error % <±0, <±0, <±0, <±0, Zero output V 0 5 0 ma 4 Zero output error mv ±0 ±0 ±0 μa <±00 Temp. coeff. sensitivity ppm/ C <±00 <±00 <±00 <±00 Input current compensation na <5 <5 <5 <5 Signal to Noise Ratio SNR (0, Hz MHz) db <60 <60 <60 <60 Common Mode Rejection CMR ( Hz khz, Gain ) db <60 <60 <60 <60 Linearity % <0,5 <0,5 <0,5 <0,5 High-pass filter 4th order Hz 0,5... 500 0,5... 500 0,5... 500 0,5... 500 Low-pass filter th order Hz 500... 0 k 500... 0 k 500... 0 k 500... 0 k Filter characteristics % Butterworth Butterworth Butterworth Butterworth Error cut-off frequency % ±0 ±0 ±0 ±0 Load resistance Ω > 000 > 000 > 000 Max. burden resistance Ω 50... 400 585A_00-7e-0.6 Page /0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Output Configurations and Signal Levels + 0V 0 + 0V - 0V + 5V + 5V - 5V - 0V 0 Single Ended Voltage ±0 V Single Ended Voltage 5 ±5 V + 5V + 0mA 0 + 0V + 4mA + 6mA - 6mA - 0V + 8mA - 5V Differential Voltage ± 0 V 0 -Wire Current 4 ±6 ma Fig. : Output configurations and signal levels Executions The differential charge amplifier is available in two enclosure versions. The characteristic features of the two executions are shown in the following table. 585A_00-7e-0.6 Type 58AA Type 58AB Enclosure Aluminum die-cast Plastic, DIN-Rail mount Operating temperature 0... 60 C 0... 60 C Degree of protection IP64 IP0 Electrical protection Connector or cable gland and terminals on sensor side and on Power/Output side Screw terminals Weight 0,5 kg 0, kg Page /0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Execution in Aluminum Die-Cast Enclosure The charge amplifier with the aluminum die-cast enclosure meets IP64. Connection to the charge amplifier on the sensor side and on the Power / Output side can be with a connector or with a cable gland and terminals. Fig. 4: Dimensions Type 58A in aluminum die-cast enclosure Configuration Options The execution in the aluminum die-cast enclosure can be ordered with connectors or cable gland and terminals on either the sensor side or the Power/Output side. Type 58AAC... Type 58AA_P... Sensor Signal Output and Power Supply 585A_00-7e-0.6 Type 58AAP... Type 58AA_C... Fig. 5: Configuration options of the electrical connections Page 4/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Electrical Connections Sensor With connector (Type 58AA_C ) Sensor S S Sens+ 4 Sens With cable gland (Type 58AA_P ) for cable diameter 8... 0 mm Sensor Sens S Sens+ Electrical Connections Power/Output Signal With connector (Type 58AA C) M6 connector 6pol m Supply/Signal Output EXC 4 Signal+ 5 Signal 6 S 585A_00-7e-0.6 With cable gland (Type 58AA P) Supply EXC Signal Output 4 Signal+ 5 Signal 6 S Page 5/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Wiring Diagrams Measuring Chains Signal Out: Differential Voltage 58AA_ Diff Voltage Output EXC- Sig+ Sig- S S SENS+ Cable up to 00m DIFF 4V S.E. Signal Out: Single Ended Voltage 58AA_ or 58AA_ Single-ended voltage out EXC- Sig+ Sig- S S SENS+ Cable up to 00m 4V Signal Out: -Wire Current 58AA4_ -wire current output EXC- Sig+ Sig- S S SENS+ Block Diagram 585A_00-7e-0.6 Cable up to 00m R 4V Page 6/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Differential in Plastic DIN-Rail Enclosure The version in the plastic DIN-Rail enclosure with screw terminals is specially suitable for applications with high channel count. Fig. 6: Dimensions of the differential charge amplifier in the plastic DIN-Rail enclosure Electrical Connections Sensor Sens+ Sens- S 4 Type 58A Power Signal 585A_00-7e-0.6 5 6 7 8 EXC- 9 Signal+ 0 Signal- S Page 7/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Wiring Diagrams Measuring Chains Signal Out: Differential Voltage 58AB_ Diff Voltage Output Ex-nA Enclosure & Cable Gland 5 6 7 8 SENS+ EXC- 9 S Sig+ 4 0 Sig- S Cable up to 00m DIFF 4V S.E. Mounting Rail Signal Out: Single Ended Voltage 58AA_ or 58AA_ Single-ended voltage out Ex-nA Enclosure & Cable Gland 5 6 7 8 SENS+ EXC- 9 S Sig+ 4 0 Sig- S Cable up to 00m 4V Signal Out: -Wire Current Block Diagram 585A_00-7e-0.6 Mounting Rail 58AA_ or 58AA_ -wire current output Ex-nA Enclosure & Cable Gland 5 6 7 8 SENS+ EXC- 9 S Sig+ 4 0 Sig- S Cable up to 00m R 4V Mounting Rail Page 8/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Ordering Information The desired execution can be configured according to the ordering key on page 0. Note that not all combinations are possible. The table below shows the available executions. For the versions with custom specific filter settings (Filter option 'Custom') the desired high- and low pass filter setting must be selected according to the ordering key and must be specified in the order. Also note that the frequency of the low pass filter should be at least 0-times higher than the frequency of the high pass filter. Similarly, for versions with custom specific sensitivity (Sensitivity option 'Custom') the desired sensitivity in mv/pc respectively μa/pc must be specified in the order. Included Accessories Mat.-No. Two socket cap screws, M4x4 55064957 (for 58A only) Optional Accessories Mating connector to 58AA_C_ 55607 (sensor side) LEMO FFA.E.04.CLAC45, cable fixation 4, 4,5 mm AWG (0,4 mm ), solder cup Cable gland for Type 58AA_P_ and 554769 Type 58AA P, AGRO Es 080.7080, cable diameter 6 8 mm Electrical Connection Input/Output Single Ended ±0 V Charge to Voltage Conversion (Sensitivity) mv/pc; ua/pc Default 0 mv/pc (6 ma/pc) Custom 0,5... 4 000 mv/pc (0,5... 400 ma/pc) Single Ended 5 ±5 V Diff ±0 V -wire Current 4 ±6 ma Single Ended ±0 V Single Ended 5 ±5 V Diff ±0 V -wire Current 4 ±6 ma Execution in Alu Die-Cast Enclosure Filter Default f 0,5 Hz; ftp 0 khz Filter Custom f 0,5 500 Hz; ftp 500 Hz 0 (0) khz CC CP PC PP TT N/A N/A N/A N/A N/A N/A N/A N/A CC CP PC PP TT N/A N/A N/A N/A N/A N/A N/A N/A CC N/A N/A N/A N/A N/A N/A N/A N/A CP N/A N/A N/A N/A N/A N/A N/A N/A PC N/A N/A N/A N/A N/A N/A N/A N/A PP N/A N/A N/A N/A N/A N/A N/A N/A TT CC N/A N/A N/A N/A N/A N/A N/A N/A CP N/A N/A N/A N/A N/A N/A N/A N/A PC N/A N/A N/A N/A N/A N/A N/A N/A PP N/A N/A N/A N/A N/A N/A N/A N/A TT 585A_00-7e-0.6 Execution in DIN-Rail Enclosure Filter Default f 0,5 Hz; ftp 0 khz Filter Custom f 0,5 500 Hz; ftp 500 Hz 0 (0) khz Page 9/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com
Differential, Type 58A... Ordering Key Type 58A Enclosure Aluminum die-cast enclosure Plastic DIN-Rail enclosure A B Output Signal Single ended voltage out, ±0 V Single ended voltage out, 5 ±5 V Differential voltage out, ±0 V -wire current, 4 ±6 ma 4 Electrical Connections IN connector / OUT connector IN connector / OUT cable gland IN cable gland / OUT connector IN cable gland / OUT cable gland Terminal block CC CP PC PP TT Filter Default (f 0,5 Hz/f 0 khz) Custom f 0,5 Hz 7 Hz 90 Hz 0,7 Hz 9 Hz 0 Hz 0,9 Hz Hz 50 Hz, Hz 5 Hz 00 Hz,5 Hz 0 Hz 50 Hz Hz 5 Hz 00 Hz,5 Hz 0 Hz 400 Hz Hz 40 Hz 500 Hz 4 Hz 55 Hz 5,5 Hz 70 Hz D C f 0,5 khz khz 7 khz 0,7 khz,5 khz 0 khz 0,9 khz khz khz, khz 4 khz 5 khz,5 khz 5,5 khz 0 khz Restriction: f >0* f 585A_00-7e-0.6 Charge Conversion Factor (Sensitivity) Default U-Out version: 0 mv/pc I-Out version: 6 μa/pc Custom * SE voltage Out ±0 V: 0 400 mv/pc SE voltage Out 5 ±5 V: 5... 00 mv/pc Diff. Out ±0 V: 0 400 mv/pc I-Out 4 ±6 ma: 6 40 μa/pc * Extended ranges are available on request D C Page 0/0 05... 06, Kistler Group, Eulachstrasse, 8408 Winterthur, Switzerland Tel. +4 5 4, Fax +4 5 4 4 4, info@kistler.com, www.kistler.com