/ GENERAL GUIDELINES AND TECHNICAL SPECIFICATIONS OF UNIFORM FABRICS FOR MGVCL EMPOLYEES FOR BLOCK YEAR 2011-2013 MADHYA GUJARAT VIJ COMPANY LTD. REGISTERED OFFICE: SARDAR PATEL VIDYUT BHAVAN, RACE COURSE, VADODARA - 390 007 [Specification of Uniform Fabrics for MGVCL Employees// Page 1 of 27]
/ General Guidelines for Sourcing of Fabrics 1. Fabric samples along with shade band and lab dips have to be approved prior to bulk production. 2. The shade band and lab dips will have to be approved before the commencement of fabric production. The shade will be matched visually. Any shade variation, from the approved shade will not be acceptable. 3. Test report will have to attached along with samples of each offered itmes 4. All testing should be carried out by an independent accredited agency nominated by MGVCL 5. Lot wise Test report for the mentioned parameter will have to be submitted before dispatch of fabric 6. Fabric will be in the form of packed of length as per schedule A of tender / requirement of MGVCL and as per specifications of Fabric pack No.: 1/2/3/4/5/6 (Each applicable for the respective product) 7. Trims specified in the respective sheets are also to be enclosed in the same pack, refer fabric Pack No. 1/2/3/4/5/6 8. No fabric defect of any nature is permissible in the fabric pack, refer Annexure No. 1 9. Fabric has to comply with all the mentioned test standards 10. Each Fabric Pack must be traceable to the lot Number. 11. Shade variation within the same piece is strictly unacceptable. 12. The fabric will be accepted only after a pre dispatch inspection by an independent accredited agency nominated by MGVCL or any person/s deputed by MGVCL and as per MGVCL tender specification / approved/ accepted specification by MGVCL 13. Any other guideline that might be laid down to ensure the best quality of fabric /garment// trim/accessory being procured. 14. The successful bidder / suppliers must have to submit one sample of uniform fabrics of printed full length Saree and Dupatta, as per photo design and specification of tender, for approval of MGVCL prior to commencement of production without effecting delivery of schedule of materials. [Specification of Uniform Fabrics for MGVCL Employees// Page 2 of 27]
/ 15. The successful bidder / suppliers must have to submit one sample of uniform fabrics of shirting, trouser, salwar + khamez (Kurta) and blouse, as per photo design / specification of tender, for approval of MGVCL before commencement of production without effecting delivery of schedule of materials. 16. The supplier should offer the lot of cloths for initial Inspection & joint sampling. 17. At random the sample from the offered lot will be collected by MGVCL inspector before making pieces from Taka for testing at Textile committee (Govt. of India) / ATIRA / any Govt. approved laboratories Supplier shall have to bear the Testing charges & cloth. The cloth should confirm the test as per Tender specification otherwise the manufactured lot will be rejected. One sample will be tested from each lot of supply against each item. 18. Cloth should be supplied in fabric pack as per MGVCL s requirement only and after approval of ACE (Proc.) MGVCL, Corporate Office, Vadodara. 19. Audit inspection of various uniform clothes supplied in pieces at various destinations will be carried out as per MGVCL standard terms & conditions. 20. Bidders are requested to refer the following Annexure which given in the end part of this specification a. Annexure- 1: List of Fabric defects b. Annexure- 2: Specification for the packing c. Annexure- 3: Group of fabric packs for tender bid [Specification of Uniform Fabrics for MGVCL Employees// Page 3 of 27]
1. SUITING FABRIC (TROUSER): SPECIFICATION OF FABRIC SOURCING Construction Parameters Requirement Tolerance Method of Test 1 Nominal Count, Denier : IS 3442, ASTM D 1059 (a) Warp 2/40s Ne ± 5% (b) Weft 2/30s Ne ± 5% 2 No. of threads per inch IS 1963, ASTM D 3775 (a) Warp 102 +5%, -2.5% (b) Weft 68 +5%, -2.5% 3 Width, Inches 60 ± 0.5 inch IS 1954, ASTM D 3774 4 Length, Meter 1.25 ± 2 cm IS 1954 7 5 Mass (Weight in grms / sq. meter GSM), g /sq. m. 6 Fibre Composition, % 220 minimum (a) Polyester, % content 67 ± 3 units (b) Viscose, % content 33 ± 3 units Breaking strength on 5cm x 20cm strip, N (kgf) Minimum (a) Warpway 600 (61) (b) Weftway 400 (40.5) 8 Tear Strength, N (kgf) Minimum (a) Warpway 25 (2.5) (b) Weftway 15 (1.5) IS 1964, ASTM D 3776 IS 667,, IS 3416 part 1, AATCC 20/20A, etc. IS 1969, ASTM D 5035 IS 6489, ASTM D 1424 [Specification of Uniform Fabrics for MGVCL Employees// Page 4 of 27]
Essential Functional Parameters Requirement Tolerance 9 Colour Fastness Rating to Minimum 10 (a) Light: Change in colour 5 (b) Washing: Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) Staining on adjacent fabric 4 Method of Test IS 686 or 2454, AATCC 16, ISO 105-B02 IS 3361, AATCC 61-2003, ISO 105-C10 IS 971, ISO 105- E04 IS 766, AATCC 8 (e)rubbing & 165, ISO 105- X12 Dry 4 Wet 3 (c) Hot Pressing IS 689, AATCC 133 Staining on adjacent fabric 4 Other Functional Parameters Requirement Tolerance Method of Test Crease recovery angle, degrees (a) Dry (b) Wet Minimum IS 4681, AATCC 66 240 degrees 240 degrees 11 Drape, % 60-75 IS 8357 12 Dimensional stability to dry heat at 105 ± 2 o C, percent (a) Warpway 1.0 Maximum IS 12170, AATCC 135-2003 (b) Weftway 1.0 13 Dimensional change on washing, percent Maximum IS 1299, AATCC 135 & 150 2003 [Specification of Uniform Fabrics for MGVCL Employees// Page 5 of 27]
(a) Warpway 2.0 (b) Weftway 2.0 14 Pilling resistance (After 5 hr. of test) 15 Soil release efficiency, percent 4 Minimum IS 10971, ASTM 3512 80 Minimum IS 11813 16 ph value of aqueous extract 6.0 to 8.0 IS 1390 (Hot method) 17 Abrasion resistance, 5000 IS 12673, ASTM D 4 cycles, (Martindale method) 4966 18 Limited flame spread index 2 Minimum IS 15758 (Part 4) DESIGN SPECIFICATION FOR SUITING FABRIC: ITEM DETAILS Wrap Pattern Dark Navy Blue Colour of the yarn as seen in the simulation of the fabric Weft Pattern Black -do- Drafting Order X X X 2 2 X X X X X 2 2 X X X X X X X X X X X X X X X X X X X X X X X X Weave Peg Plan [Specification of Uniform Fabrics for MGVCL Employees// Page 6 of 27]
2. SHIRTING FABRIC (all Male Staff): Construction Parameters Requirement Tolerance Method of Test 1 Nominal Count, Denier IS 3442 (a) Warp 40s Ne ± 5% (b) Weft 40s Ne ± 5% 2 No. of threads per inch IS 1963, ASTM D 3775 (a) Warp 136 +5%, -2.5% (b) Weft 72 +5%, -2.5% 3 Width, Inches 60 ± 0.5 inch IS 1954, ASTM D 3774 4 Length, Meter 1.65 ± 2 cm IS 1954 5 Mass (Weight in grms / sq.meter GSM) 6 Fibre Composition, % 130 ± 5% (a) Polyester, % content 50 ± 3 units (b) Cotton, % content 50 ± 3 units IS 1964, ASTM D 3776 IS 667, AATCC 20/20A, IS 1564, IS1889, 2005, IS 2176, IS 2177, IS 3416, IS 3421, IS 1969 [Specification of Uniform Fabrics for MGVCL Employees// Page 7 of 27]
7 Essential Functional Requirement Parameters Breaking strength on 5cm x 20cm strip, N (kgf) (a) Warpway 440 (44.9) (b) Weftway 350 (35.7) Tolerance Minimum 8 Tear Strength, N (kgf) Minimum (a) Warpway 10.0 (1.0) (b) Weftway 8.0 (0.8) 9 Colour Fastness Rating to Minimum (a) Light: Change in colour 5 (b) Washing: Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) Staining on adjacent fabric 4 (e)rubbing Dry 4 Wet 3 (c) Hot Pressing Staining on adjacent fabric 4 Method of Test IS 1969, ASTM D 5035 IS 6489, ASTM D 1424 IS 686 or 2454, AATCC 16, ISO 105- B02 IS 3361, AATCC 61-2003, ISO 105 C10 IS 971, ISO 105-E04, IS 766, AATCC 8 & 165, ISO 105-X12 IS 689, AATCC 133 [Specification of Uniform Fabrics for MGVCL Employees// Page 8 of 27]
10 Other Functional Parameters Crease recovery angle, degrees (a) Dry (b) Wet Requirement Tolerance Minimum Method of Test IS 4681, AATCC 66 240 degrees 240 degrees 11 Drape, % 60-75 IS 8357 12 Dimensional stability to dry heat at 105 ± 2 o C, percent (a) Warpway 1.0 (b) Weftway 1.0 15 Dimensional change on washing, percent (a) Warpway 2.0 (b) Weftway 2.0 16 Pilling resistance (After 5 hr. of test) 17 Soil release efficiency, percent 18 ph value of aqueous extract (Hot method) 19 Abrasion resistance, 5000 cycles, (Martindale method) Maximum Maximum 4 Minimum IS 12170, AATCC 135-2003 IS 1299, AATCC 135 & 150 2003 IS 10971, ASTM 3512 80 Minimum IS 11813 6.0 to 8.0 IS 1390 20 Limited flame spread index 2 Minimum 4 IS 12673, ASTM D 4966 IS 15758 (Part 4) [Specification of Uniform Fabrics for MGVCL Employees// Page 9 of 27]
DESIGN SPECIFICATION FOR SHIRTING FABRIC: ITEM Wrap Pattern Weft Pattern DETAILS Colour of the yarn as seen 07 Light Blue in the simulation of the fabric 02 Medium Blue -do- 05 Light Blue -do- 01 Medium Blue -do- Light Blue (same as light blue -doof wrap) Drafting Order X X X X X X X X X X X X X X X X X X X X Weave Peg Plan [Specification of Uniform Fabrics for MGVCL Employees// Page 10 of 27]
3. DRESS MATERIAL (Salwar + Kurta / Kameez) Construction Parameters Requirement Tolerance Method of Test 1 Nominal Count, Denier IS 3442 (a) Warp 40s Ne ± 5% (b) Weft 40s Ne ± 5% 2 No. of threads per inch IS 1963, ASTM D 3775 (a) Warp 136 +5%, -2.5% (b) Weft 72 +5%, -2.5% 3 Width, Inches 60 ± 0.5 inch IS 1954, ASTM D 3774 4 Length, Meter 3.75 ± 2 cm IS 1954 ASTM D 3774 5 Mass (Weight in grms / sq. meter GSM), g/ sq. m. 6 Fibre Composition, % 130 ± 5% (a) Polyester, % content 67 ± 3 units (b) Cotton, % content 33 ± 3 units IS 1964, ASTM D 3776 IS 667, AATCC 20/20A, IS 1564, IS1889, 2005, IS2176, IS 2177, IS 3416, IS 3421, IS 1969 [Specification of Uniform Fabrics for MGVCL Employees// Page 11 of 27]
Essential Functional Parameters Requirement Tolerance Method of Test 7 Breaking strength on 5cm x 20cm strip, N (kgf) Minimum IS 1969, ASTM D 5035 (a) Warpway 440 (44.9) (b) Weftway 350 (35.7) 8 Tear Strength, N (kgf) Minimum IS 6489, ASTM D 1424 (a) Warpway 10.0 (1.0) (b) Weftway 8.0 (0.8) 9 Colour Fastness Rating to Minimum (a) Light: IS 686 or 2454, AATCC 16, ISO 105-B02 Change in colour 5 (b) Washing: IS 3361, AATCC 61-2003, ISO 105-C10 Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) IS 971, ISO 105-E04 Staining on adjacent fabric 4 (e)rubbing IS 766, AATCC 8 & 165, ISO 105-X12 Dry 4 Wet 3 (c) Hot Pressing IS 689, AATCC 133 Staining on adjacent fabric 4 [Specification of Uniform Fabrics for MGVCL Employees// Page 12 of 27]
Other Functional Parameters Requirement Tolerance Method of Test 10 Crease recovery angle, degrees Minimum IS 4681, AATCC 66 (a) Dry 240 degrees (b) Wet 240 degrees 11 Drape, % 60-75 IS 8357 12 Dimensional stability to dry heat at 105 ± 2 o C, percent (a) Warpway 1.0 (b) Weftway 1.0 13 Dimensional change on washing, percent (a) Warpway 2.0 (b) Weftway 2.0 14 Pilling resistance (After 5 hr. of test) 15 Soil release efficiency, percent 16 ph value of aqueous extract (Hot method) 17 Abrasion resistance, 5000 cycles, (Martindale method) Maximum Maximum IS 12170, AATCC 135-2003 IS 1299, AATCC 135 & 150 2003 4 Minimum IS 10971, ASTM 3512 80 Minimum IS 11813 6.0 to 8.0 IS 1390 4 IS 12673, ASTM D 4966 18 Limited flame spread index 2 Minimum IS 15758 (Part 4) [Specification of Uniform Fabrics for MGVCL Employees// Page 13 of 27]
DESIGN SPECIFICATION FOR (Salwar + Kurta / Kameez) FABRIC: COLOUR FOR SALWAR FABRIC ITEM DETAILS Colour Dark blue with purple tint As dark blue (with purple tint) colour of print out of the design of dupatta COLOUR FOR KURTA FABRIC Colour Light blue As light blue colour of print out of the design of dupatta. [Specification of Uniform Fabrics for MGVCL Employees// Page 14 of 27]
4. DUPATTA Construction Parameters Requirement Tolerance Method of Test 1 Nominal Count, Denier IS 3442 (a) Warp 75 Denier ± 5% (b) Weft 75 Denier ± 5% 2 Twist per meter, (TPM) IS 832, ASTM D 1422/1423 (a) Warp 1800, S & Z, alternate ± 5% (b) Weft 1800, S & Z, alternate ± 5% 3 No. of Filaments in Yarn ASTM D 1423-02 (a) Warp 36 ± 2 (b) Weft 36 ± 2 4 No. of threads per inch IS 1963, ASTM D 3775 (a) Warp 108 +5%, -2.5% (b) Weft 82 +5%, -2.5% 5. Width, Inches 44.5 ± 0.5 inch IS 1954, ASTM D 3774 6. Length, Meter 2.5 ± 2 cm IS 1954 7 Mass (Weight in grms / sq.meter GSM), g/ sq. m. 8 Fibre Composition, % 65 ± 5% (a) Polyester, % content 100 p Nil (b) Cotton/Viscose, % content 0 Nil IS 1964, ASTM D 3776 IS 667, AATCC 20/20A, IS 1564, IS1889, 2005, IS2176, IS 2177, IS 3416, IS 3421, IS 1969 [Specification of Uniform Fabrics for MGVCL Employees// Page 15 of 27]
Essential Functional Parameters Requirement Tolerance Method of Test 9 Breaking strength on 5cm x 20cm strip, N (kgf) Minimum IS 1969, ASTM D 5035 (a) Warpway 200 (20.4) (b) Weftway 150 (15.3) 10 Tear Strength, N (kgf) Minimum IS 6489, ASTM D 1424 (a) Warpway 15 (1.5) (b) Weftway 11 (1.1) 11 Colour Fastness Rating to Minimum IS 686 or 2454, (a) Light: AATCC 16, ISO 105- B02 Change in colour 5 (b) Washing: IS 3361, AATCC 61-2003, ISO 105-C10 Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) IS 971, ISO 105-E04 Staining on adjacent fabric 4 (e)rubbing IS 766, AATCC 8 & 165, ISO 105-X12 Dry 4 Wet 3 (c) Hot Pressing IS 689, AATCC 133 Staining on adjacent fabric 4 [Specification of Uniform Fabrics for MGVCL Employees// Page 16 of 27]
Other Functional Requirement Tolerance Method of Test Parameters 12 Crease recovery angle, degrees Minimum IS 4681, AATCC 66 (a) Dry 240 degrees (b) Wet 240 degrees 13 Drape, % 60-75 IS 8357 14 Dimensional stability to dry heat at 105 ± 2 o C, percent (a) Warpway 1.0 (b) Weftway 1.0 15 Dimensional change on washing, percent (a) Warpway 2.0 (b) Weftway 2.0 Maximum Maximum IS 12170, AATCC 135-2003 IS 1299, AATCC 135 & 150 2003 16 Pilling resistance (After 5 hr. of test) 4 Minimum IS 10971, ASTM 3512 17 Soil release efficiency, percent 80 Minimum IS 11813 18 ph value of aqueous extract (Hot method) 6.0 to 8.0 IS 1390 19 Abrasion resistance, 5000 IS 12673, ASTM D 4 cycles, (Martindale method) 4966 20 Limited flame spread index 2 Minimum IS 15758 (Part 4) DESIGN SPECIFICATION FOR DUPATTA FABRIC: ITEM Colours of the design Light Blue Medium blue Dark blue with purple tint Dark pink DETAILS Colour as given in print out of the design, same as light blue stripes of the shirting fabric. Colour as given in print out of the design, same as medium blue background of the shirting fabric. Colour as given in print out of the design Colour as given in print out of the design [Specification of Uniform Fabrics for MGVCL Employees// Page 17 of 27]
5. SARI Construction Parameters Requirement Tolerance Method of Test 1 Nominal Count, Denier IS 3442 (a) Warp 70 Denier ± 5% (b) Weft 70 Denier ± 5% 2 Twist per meter, (TPM) IS 832 (a) Warp 2000-2200, S & Z ± 5% alternate (b) Weft 2000-2200, S & Z ± 5% alternate 3 No. of Filaments in Yarn (a) Warp 36 ± 2 (b) Weft 36 ± 2 4 No. of threads per inch IS 1963, (a) Warp 132 +5%, -2.5% (b) Weft 86 +5%, -2.5% 5. Width, Inches 44.5 ± 0.5 inch IS 1954 6. Length, Meter 5.5 ± 2 cm IS 1954 7 Mass (Weight in grms / sq.meter GSM), g/ sq. m. 70 ± 5% IS 1964 8 Fibre Composition, % IS 1564, IS 1889, IS 2005, IS 2176, IS 2177, IS 3416, IS 3421, (a) Polyester, % content 100 p Nil (b) Cotton/Viscose, % content 0 Nil [Specification of Uniform Fabrics for MGVCL Employees// Page 18 of 27]
Essential Functional Parameters 9 Breaking strength on 5cm x 20cm strip, N (kgf) Requirement Tolerance Method of Test Minimum IS 1969, ASTM D 5035 (a) Warpway 240 (24.4) (b) Weftway 190 (19.3) 10 Tear Strength, N (kgf) Minimum IS 6489, ASTM D 1424 (a) Warpway 20 (2.0) (b) Weftway 15 (1.5) 11 Colour Fastness Rating to Minimum (a) Light: IS 686 or 2454, AATCC 16, ISO 105- B02 Change in colour 5 (b) Washing: IS 3361, AATCC 61-2003, ISO 105 C10 Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) Staining on adjacent fabric 4 (e)rubbing Dry 4 Wet 3 (c) Hot Pressing Staining on adjacent fabric 4 IS 971, ISO 105-E04 IS 766, AATCC 8 & 165, ISO 105 X12 IS 689, AATCC 133 [Specification of Uniform Fabrics for MGVCL Employees// Page 19 of 27]
Other Functional Parameters Requirement Tolerance Method of Test 12 Crease recovery angle, degrees: Minimum IS 4681, AATCC 66 (a) Dry 240 degrees (b) Wet 240 degrees 13 Drape, % 60-75 IS 8357 14 Dimensional stability to dry heat at 105 ± 2 o C, percent (a) Warpway 1.0 (b) Weftway 1.0 15 Dimensional change on washing, percent (a) Warpway 2.0 (b) Weftway 2.0 Maximum Maximum IS 12170, AATCC 135-2003 IS 1299, AATCC 135 & 150 2003 16 Pilling resistance (After 5 hr. of test) 4 IS 10971, ASTM 3512 17 Soil release efficiency, percent 80 Minimum IS 11813 18 ph value of aqueous extract (Hot method) 6.0 to 8.0 IS 1390 19 Abrasion resistance, 5000 IS 12673, ASTM D 4 cycles, (Martindale method) 4966 20 Limited flame spread index 2 Minimum IS 15758 (Part 4) DESIGN SPECIFICATION FOR SARI FABRIC: ITEM Colours of the design DETAILS Colour as given in print out of Light Blue the design, (same as that of dupatta fabric) Medium blue -do- Dark blue with purple -dotint Dark pink -do- [Specification of Uniform Fabrics for MGVCL Employees// Page 20 of 27]
6. BLOUSE Construction Parameters Requirement Tolerance Method of Test 1. Nominal Count, Denier IS 3442 (a) Warp 62 ± 5% (b) Weft 62 ± 5% 2. Twist per meter, (TPI) IS 832 (a) Warp (b) Weft High twist, Alternate S & Z High twist, Alternate S & Z 3 No. of threads per inch (a) Warp 100 +5%, -2.5% (b) Weft 80 +5%, -2.5% 4 Width, Inches 35.0 ± 0.5 inch IS 1963 5 Length, Meter 1.0 ± 2 cm 6 Mass (Weight in grms / sq.meter GSM), g/ sq. m. 70 ± 5% 7 Fibre Composition, % IS 1954 (a) Polyester, % content 67 p Nil IS 1954 (b) Cotton/Viscose, % content 33 p Nil IS 1964 IS 1564, IS1889, 2005, IS2176, IS 2177, IS 3416, IS 3421 [Specification of Uniform Fabrics for MGVCL Employees// Page 21 of 27]
Essential Functional Parameters Requirement Tolerance Method of Test 8 Breaking strength on 5cm x 20cm strip, N (kgf): Minimum IS 1969, ASTM D 5035 (a) Warpway 200 (20) (b) Weftway 150 (15) 9 Tear Strength, N (kgf) Minimum IS 6489, ASTM D 1424 (a) Warpway 8 (0.8) (b) Weftway 6 (0.6) 10 Colour Fastness Rating to Minimum IS 686 or 2454, (a) Light: AATCC 16, ISO 105 B02 Change in colour 5 (b) Washing: IS 3361, AATCC 61-2003, ISO 105 C10 Staining on adjacent fabric 3-4 (c) Perspiration (acidic and alkaline) IS 971, ISO 105-E04 Staining on adjacent fabric 4 (e) Rubbing IS 766, AATCC 8 & 165, ISO 105 X12 Dry 4 Wet 3 (c) Hot Pressing IS 689, AATCC 133 Staining on adjacent fabric 4 [Specification of Uniform Fabrics for MGVCL Employees// Page 22 of 27]
Other Functional Parameters Requirement Tolerance Method of Test 11 Crease recovery angle, degrees: Minimum IS 4681, AATCC 66 (a) Dry (b) Wet 12 Drape, percent 60-75 IS 8357 13 Dimensional stability to dry heat at 105 ± 2 o C, percent: (a) Warpway 1.0 (b) Weftway 1.0 14 Dimensional change on washing, percent: (a) Warpway 2.0 (b) Weftway 2.0 Maximum Maximum IS 12170, AATCC 135-2003 IS 1299, AATCC 135 & 150-2003 15 Pilling resistance (After 5 hr. of test) 4 Minimum IS 10971, ASTM 3512 16 Soil release efficiency, percent 80 Minimum IS 11813 17 ph value of aqueous extract (Hot method) 6.0 to 8.0 IS 1390 18 Abrasion resistance, 5000 IS 12673, ASTM D 4 cycles, (Martindale method) 4966 19 Limited flame spread index 2 Minimum IS 15758 (Part 4) [Specification of Uniform Fabrics for MGVCL Employees// Page 23 of 27]
COLOUR FOR BLOUSE FABRIC: ITEM Colour Dark blue with purple tint DETAILS As dark blue(with purple tint) Colour of print out of the design of sari [Specification of Uniform Fabrics for MGVCL Employees// Page 24 of 27]
ANNEXURE: 1 List of Fabric Defects Nature Yarn Defects Weaving Defects Processing Defects Defects Broken Filaments, Color flecks, Slubs, Knots Broken Ends, Broken Ends Woven in a Bunch, Broken Pattern, Double End, Float, Gout, Hole-Cut or Tear, Lashing-in, Local Distortion, Missing Ends, Oil or other Stain, Oily or Soiled Ends, Oily Weft, Reed Marks, Selvedge Defect, Slough Off, Smash, Snarls, Stitches, Untrimmed Loose threads, Weft Bar, Weft Crack. Bleaching spot, Blurred or Dark Patch, Defects caused by Hanging Thread, Dye Bar, Dyestuff Stain Misprint/Absence of Print, Patchy or Streaky or Uneven Dyeing, Pilling, Shading or Listing, Uneven Printing or Tinting, Water Mark, White Spot. Embroidery Defects Wrong Placement, Tilting of Embroidery, Broken threads, Incomplete embroidery, Shade Variation. Visual Defect Any visual defect that may affect, salability, serviceability, appearance of the fabric in a way that is significantly unacceptable for sale. [Specification of Uniform Fabrics for MGVCL Employees// Page 25 of 27]
ANNEXURE: 2 Specifications for packing: 1. Pack should contain fabric of length as specified in schedule A of tender 2. Ready Pack size 12 x10 ( +/- ½ ) 3. Material: Self adhesive poly bag, gauge: 200 4. Necessary warning should be printed in front side of bag to keep it away from the reach of children. 12 Warning This bag is not a toy. Keep it away from the reach of children This side up Sticker Hole Pack No: 16 font Fabric code: 14 font Colour code: 14 font Lot no: 12 font Sort No.: 12 font 10 [Specification of Uniform Fabrics for MGVCL Employees// Page 26 of 27]
/ ANNEXURE: 3 Group of Fabric Pack for Tender bid Sr. No. Group Details Fabric Pack Fabric: 1 Group-1 (Corporate & Field staff) Shirting Fabric pack No.: Male Staff: Administration &Technical 2 2 Group-2 3 Group-3 4 Group-4 Fabric: Salwar Kurta + Dupatta Female Staff: Administration Fabric: Suiting Male Staff: Administration Fabric: Sari + Blouse Female Staff: Administration & Technical Note: Bidder can bid for only one, more than one or all groups Fabric pack No.: 3 + 4 Fabric pack No.: 1 Fabric pack No.: 5 + 6 IMPORTANT NOTE: THE DESIGN OF UNIFORM FABRICS OF SAREE AND DUPATTA SHALL BE STRCKLY AS PER TENDER SPECIFICATION AND AS PER COLOURED PHOTO / DESIGN / DRAWING OF TENDER UPLOADED ON WEB WITH THIS TENDER ONLY. [Specification of Uniform Fabrics for MGVCL Employees// Page 27 of 27]