LED WALL WASHERS SPECIFICATIONS & INSTALLATION GUIDE

LED WALL WASHERS SPECIFICATIONS & INSTALLATION GUIDE

ContenTS: Brief specifications LED WALL WASHER WWF 12 48... 4 LED WALL WASHER WWB 14 36... 5 LED WALL WASHER WWS 16 12... 6 LED WALL WASHER WWS 32 24... 7 LED WALL WASHER WWS 48 36... 8 24V LED WALL WASHER WWT 15 12... 9 24V LED WALL WASHER WWT 24 90...10 24V LED WALL WASHER WWT 48 180...11 Installation GUIDE WWS, WWF, WWB SERIES HARD WIRE...12 WWS, WWF, WWB SERIES PLUG & PLAY...13 WWT SERIES HARD WIRE...14 WWT SERIES PLUG & PLAY...15

IMPORTANT SAFETY INSTRUCTIONS When installing or using this product, basic safety precautions should always be followed including the following: 1. Read all instructions before attempting to install this product. 2. Ensure main power is off before installing or wiring this product. 3. Ensure correct voltage is being used for this product. 4. Disconnect electrical power before adding to or changing the configuration of this product. 5. Fixtures must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulation.

led Wall WaSHer WWF 12 48 12-1/2" 10-5/8" 7-3/4" 3" SpeCifiCationS Model WWf 12 48 pp 60 W30 WWf 12 48 pp 60 W50 WWf 12 48 pp 60 rgb WWf 12 48 pp 60 awb led Quantity 48 Wattage 56 W lumens 2500 lm 3300 lm 1890 2360 efficacy 44.6 lm/w 58.9 lm/w 33.8 lm/w 42.1 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle 120 x 60 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish 100-240V AC 50,000 hours 12 1/2"L 10 5/8"H 7 3/4"D 11.5 lbs / 5.2 kg Aluminum Z Bronze (Standard) operating temperature -4 F 113 F / -20 C 45 C operating Humidity Mounting Maximum run environment Certifications Warranty 10% - 90% RH Bracket and handle. Steel Yoke with bolt holes and screw holes. 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWf 12 48 pp - Plug & Play 60-60 x120 W30-3000K Z - Bronze HW - Hard Wire* W60-6000K a - Aluminum* rgb B - Black* awb W - White* * Custom options Consult factory example: WWf 12 48 pp 60 W30 Z 4

LED WALL WASHER WWB 14 36 13-1/2" 7-1/8" 11-1/2" 6-3/8" SPECIFICATIONS Model WWB 14 36 PP 30 W30 WWB 14 36 PP 30 W50 WWB 14 36 PP 30 RGB WWF 14 36 PP 30 AWB LED Quantity 36 Wattage Lumens 1500 lm 2000 lm 1143 1429 Efficacy 37.5 lm/w 50 lm/w 28.6 lm/w 35.8 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue CRI 75 N/A 40W Beam Angle* 30 Voltage Lamp Life Dimensions Weight Housing Finish 100-240V AC 50,000 hours 13 1/2" L x 11 1/2" H x 6 3/8" D 10 lbs / 4.5kg Aluminum Z Bronze (Standard) Operating Temp -4 F 113 F / -20 C 45 C Operating Humidity DMX Input Mounting Maximum Run Environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX Plug Screw holes on steel baseplate with integral 24V DC 350mA power supply 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ORDERING INSTRUCTIONS MODEL WIRING TYPE BEAM ANGLE CCT FINISH WWB 14 36 PP - Plug & Play 30-30 W30-3000K Z - Bronze * Custom options Consult factory HW - Hard Wire* 15-15 * W60-6000K A - Aluminum* 60-60 * RGB B - Black* AWB W - White* Example: WWB 14 36 PP 30 W30 Z 5

led Wall WaSHer WWS 16 12 16-3/8" 4-1/2" 2-1/4" 2-3/4" 15-1/4" SpeCifiCationS Model WWS 16 12 pp 30 W30 WWS 16 12 pp 30 W50 WWS 16 12 pp 30 rgb WWS 16 12 pp 30 awb led Quantity 12 Wattage lumens 816 1044 597 746 efficacy 58.3 lm/w 74.6 lm/w 42.6 lm/w 53.3 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue 14W Beam angle* 30 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish 100-240V AC 50,000 hours 16 3/8" L x 2 3/4" W x 4 1/2" H 4 lbs / 1.8 kg Aluminum Z Bronze (Standard) operating temp -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS 16 12 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS 16 12 pp 30 W30 Z 6

led Wall WaSHer WWS 32 24 32" 4-1/2" 2-1/4" 2-3/4" 30-7/8" SpeCifiCationS Model WWS 32 24 pp 30 W30 WWS 32 24 pp 30 W50 WWS 32 24 pp 30 rgb WWS 32 24 pp 30 awb led Quantity 24 Wattage lumens 1100 1500 857 1071 efficiency 39.3 lm/w 53.6 lm/w 30.6 lm/w 38.25 lm/w Color temperature 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Cri 75 N/A 28W Beam angle* 30 Voltage lamp life Dimensions Weight Housing finish 100-240V AC 50,000 hours 32" L x 2 3/4" W x 4 1/2" H 5.5 lbs / 2.5 kg Aluminum Z Bronze (Standard) operating temperature -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS 32 24 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS 32 24 pp 30 W30 Z 7

led Wall WaSHer WWS 48 36 47-7/8" 4-1/2" 2-1/4" 2-3/4" 46-3/4" SpeCifiCationS Model WWS 48 36 pp 30 W30 WWS 48 36 pp 30 W50 WWS 48 36 pp 30 rgb WWS 48 36 pp 30 awb led Quantity 36 Wattage lumens 1500 2000 1143 1429 efficacy 33.3 lm/w 44.4 lm/w 25.4 lm/w 31.8 lm/w Color temperature 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue 45W Beam angle* 30 Cri 75 N/A Voltage lamp life Dimensions Weight Housing finish 100-240V AC 50,000 hours 47 7/8" L x 2 3/4" W x 4 1/2" H 8.8 lbs / 4 kg Aluminum Z Bronze (Standard) operating temp -22 F 104 F / -30 C 40 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 Pin Washer DMX male Plug Steel Yoke with bolt holes and screw holes 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWS 48 36 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWS 48 36 pp 30 W30 Z 8

24V led Wall WaSHer WWT 15 12 15-1/2"L 6-3/4"W 13-3/8" 2-1/8" 3-1/4" 5-3/4" 5-1/4"H 1-7/8" SpeCifiCationS Model WWt 15 12 pp 30 W30 WWt 15 12 pp 30 W50 WWt 15 12 pp 30 rgb WWt 15 12 pp 30 awb led Quantity Wattage 12 (Bridgelux) lumens 816 1044 600 750 efficacy 54.4 69.6 40 lm/w 50 lm/w Color 3000K 3500K 5000K 5500K Red, Green, Blue Amber, White, Blue 15W Beam angle* 30 Voltage efficiency lamp life Dimensions Weight Housing finish 24V DC 0.9 PF 50,000 hours 15 1/2" L x 6 3/4" W x 5 1/4" H 6.6 lb Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 pin Jesco DMX plug Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt 15 12 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt 15 12 pp 30 W30 Z 9

24V led Wall WaSHer WWT 24 90 23-5/8"L 5-1/2"H 7-3/8"W SpeCifiCationS Model WWt 24 90 pp 30 W30 WWt 24 90 pp 30 W50 WWt 24 90 pp 30 rgb WWt 24 90 pp 30 awb led Quantity Wattage 36 (Bridgelux) 105W lumens 5100 lm 6000 lm 3429 4286 efficacy 48.6 lm/w 57.1 lm/w 32.7 lm/w 40.8 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle* 30 Voltage 24V DC efficiency PF 0.60 lamp life Dimensions Weight Housing finish 50,000 hours 23 5/8" L x 7 3/8" W x 5 1/2" H 11 lbs / 5 kg Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity DMX input Mounting Maximum run environment Certifications Warranty 10% - 90% RH 3 pin Jesco DMX plug Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; A Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt 24 90 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt 24 90 pp 30 W30 Z 10

24V led Wall WaSHer WWT 48 180 47-3/8"L 5-1/2"H 7-3/8"W SpeCifiCationS Model WWt 48 180 pp 30 W30 WWt 48 180 pp 30 W50 WWt 48 180 pp 30 rgb WWt 48 180 pp 30 awb led Quantity Wattage 72 (Bridgelux) 176W lumens 7100 lm 8200 lm 4686 5857 efficacy 40.3 lm/w 46.6 lm/w 26.6 lm/w 33.3 lm/w Color 3000K 3500K 5500K 5500K Red, Green, Blue Amber, White, Blue Beam angle* 30 Voltage 24V DC efficiency PF 0.60 lamp life Dimensions Weight Housing finish 50,000 hours 47 3/8" L x 7 3/8" W x 5 1/2" H 20.3 lbs / 9.2 kg Aluminum Z Bronze (Standard) operating temp -4 F 113 F / -20 C 45 C operating Humidity 10% - 90% RH DMX input Jesco DMX 3-pin plug 3 pin Washer DMX plug Mounting Maximum run environment Certifications Warranty Surface Mount 16 Fixtures or 1,000 feet Dry, Wet, IP65 ETL/cETL, CE, RoHS 5 Years see published warranty terms for detailed information. * Consult the factory for custom beam angles: 15 and 60. Consult factory for custom finishes; a Aluminum (MOQ 50 pcs), B Black (MOQ 150 pcs), W White (MOQ 150 pcs). View installation instructions for detailed information. ordering instructions MoDel WirinG type BeaM angle CCt finish WWt 48 180 pp - Plug & Play 30-30 W30-3000K Z - Bronze HW - Hard Wire* 15-15 * W60-6000K a - Aluminum* 60-60 * rgb B - Black* awb W - White* * Custom options Consult factory example: WWt 48 180 pp 30 W30 Z 11

WWS, WWF, WWB SerieS HARD WIRE 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address (000 512). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 3. ensure Main POWER IS off. 4. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. 5. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. See Controller specification sheet for more details. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Optional A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Max. 16 fixtures WWB, WWF, or WWS WWB, WWF, or WWS WWB, WWF, or WWS LC-DMX-AMP2 DMX CONTROLLER* 2-port DMX Distribution WWB, WWF, or WWS Main Power * See controller specification sheet for more details. 12

WWS, WWF, WWB SERIES PLUG & PLAY 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address (000 512). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 3. ensure Main POWER IS off. 4. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chain. 5. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. See Controller specification sheet for more details. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten Optional A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. DMX Adressing Interface Max. 16 fixtures WWB, WWF or WWS WWB, WWF or WWS WWB, WWF or WWS LC-DMX-AMP1 LC-DMX-AMP2 1-port DMX Distribution To DMX CONTROLLER* 2-port DMX Distribution AC AC AC WWB, WWF or WWS DL-PS-XX/24-JB DL-PS-XX/24-JB AC AC AC * See controller specification sheet for more details. 13

WWT SERIES HARD WIRE 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Install Power Supply Determine location of the power supply. Connect low voltage wires from power supply to the fixture. Ensure correct polarity is connected (positive to positive, negative to negative). 3. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address (000 512). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 4. ensure Main POWER IS off. cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. Optional: A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). See Controller specification sheet for more details. 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. 5. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Max. 16 fixtures WWT WWT WWT DMX CONTROLLER* LC-DMX-AMP2 2-port DMX Distribution 24V 24V 24V 24V WWT Main Power 24V * See controller specification sheet for more details. 14

WWT SERIES PLUG & PLAY 1. Configure design and lay out the system before attempting to install this product. Note A DMX controller is required to operate Wall Washer fixtures. Additional DMX adapter cables may be required. 2. Install Power Supply Determine location of the power supply. Connect low voltage wires from power supply to the power connector (WW-PC- HW/DC-72). Ensure correct polarity is connected (positive to positive, negative to negative). Connect power connector to the Washer fixture. 3. Set DMX Address Locate the DMX addressing interface on the fixture. Power the fixture. Select a DMX address (000 512). Each address consists of 3 channels (R-G-B or A-W-B). To control fixtures individually, assign a unique DMX address per fixture. To control fixtures at the same time, assign the same DMX for each fixture. 4. ensure Main POWER IS off. 5. Install Fixtures Determine locations on the mounting surface according to the desired design and layout. Ensure fixtures are installed within the maximum run length of DMX cable (1,000 feet or 300 feet for CAT5 cable). DMX wiring must be installed in a continuous run (daisy chained). Connect main power wires to Washer fixture. Optional: A DMX Distribution Amplifier is required for multiple runs (star wiring) or when installing more than 16 fixtures. Connect Fixtures Connect fixtures using DMX cable. Ensure a tight connection is made by tightening the lock nut. For harsh environments you may use a silicon compound to seal the connectors. For hardwiring, use weatherproof boxes and covers as needed (supplied by ). See Controller specification sheet for more details. 6. Connect Controller Run DMX cable from the controller to the first fixture. If no controller is connected and the DMX address is set to 001, the fixture will enter into the default test mode and cycle colors. 7. Run System Turn the power on. Check all fixtures to make sure they are running properly. If fixtures are not running properly, check all connections and retighten. Max. 16 WWT WWT WWT 24V DMX CONTROLLER* WW-PC-HW/DC-72 Main Power LC-DMX-AMP2 2-port DMX Distribution WW-PC-HW/DC-72 24V 24V 24V * See controller specification sheet for more details. WW-PC-HW/DC-72 WWT 24V WW-PC-HW/DC-72 15

NEw YORk CORPORATE OFFICES 6625 traffic avenue Glendale ny 11385 TEL 718 366 3211 TEL 800 527 7796 FAX 718 366 3646 LOS ANgELES 1100 Hatcher ave Suite a City of industry Ca 91748 TEL 626 854 8168 TEL 866 473 5840 FAX 626 854 8172 JESCOLIGHTING.COM 2011 JeSCo lighting