CLEANING TECHNOLOGY HIGH PERFORMANCE WHAT S YOUR PROBLEM? ISO 9001 CERTIFICAT SQS No. 11443 ISO 14001/ OHSAS 18001 CERTIFICAT SQS No. 30865 SWISS QUALITY ECOLOGICAL CLEANING CONCEPT What s your problem?_a 23/02/11
WHAT S YOUR PROBLEM? SOLUTION IN CHAPTER TO REMOVE 1. POLISHING COMPOUNDS, OILS, ADHESIVE RESIDUES BY ULTRASONIC. 2. OILS & GREASES BY SPRAY OR ULTRASONIC. 3. PREPARATION PRIOR TO P.V.D. 4. CLEANING & FINISHING PRIOR TO HOT AIR DRYING 5. DEOXIDIZATION. 6. PROTECTION AGAINST OXIDATION. 7. TRIBO-FINISHING. 8. REMOVING LACQUERS & VARNISH. 9. REMOVING OILS OR ZAPON BY ULTRASONIC OR BY SPRAY. 10. ANTI SCRATCH LACQUER. 11. REMOVING OILS IN INTER-OPERATIONAL CLEANING : BARREL-TOP DEGREASER / ULTRASONIC / TO REPLACE BENZINE CLEANERS. 12. REMOVING SOLDERING FLUXES. 13. CLEANING PARAMETERS CONTROL. 14. DI WATER RINSE QUALITY CONTROL.3. 15. WASTEWATER TREATMENT PROCESS. 16. IMPURITIES PRECIPITATION SYSTEM. WHAT S YOUR PROBLEM? 21/02/11 PAGE 1
PRODUCTS To remove From Recommended product +/- L/P ph Instructions for use 1 POLISHING COMPOUNDS and OIL RESIDUES or GALVEX 18.01 GALVEX 17.30 PL (TARNISHING FREE ON COPPER METALS) + L 10.5 + L 10.8 Temperature : 55 to 70 C Temperature : 55 to 70 C ADHESIVE RESIDUES EXCEPT ALUMINIUM BRASS GALVEX 17.30 SP.P + L 10.5 Temperature : 60 to 75 C or EXCEPT ALUMINIUM NANOCLEAN NANOCLEAN SUPRA NANOCLEAN 100 NANOCLEAN 95 + L 14 - emulsifying property - separates oils - for large quantities of oils 2 & GREASES 3 PREPARA- TION prior to P.V.D. H.S.S. HARD METAL H.S.S. STAINLESS- STEEL HARD METAL SPRAY or DECOSPRAY TM SPRAY or DECOSPRAY 347 DECOSPRAY 440 LINE VACUKLEEN (NO COBALT LEACHING) + L 9.6 + L 14 + L 13.7 + L/P www.ngl-cleaning-technology.com Temperature : 60 to 75 C NB: with oil separator Temperature : 50 to 65 C See data sheet LEGEND: + : BIODEGRADABLE - : NON BIODEGRADABLE L/P : LIQUID or POWDER : ULTRASONIC n.m. : NON MEASURABLE PAGE 2
PRODUCTS To remove 4 From Recommended product NGL 17.40 P.SP * (DECONTAMINATION). +/- L/P ph + P 9.3 Instructions for use Concentration : 5 to 20 g/l Temperature : 40 to 70 C Time : 1 to 5 min * Liquid version: HELIT FINISH Light alloys : GP 17.40 SUP. FINISHING prior to HOT AIR DRYING GLASS SAPPHIRE NICKEL SILVER BRASS STAINLESS STEEL SPRAY or FINISH 200 SUPER HELIT IC + L < 1 + L 7.7 Temperature : 45 to 65 C * on polished aluminium Temperature : 40 to 70 C SENSITIVE STEEL GALVEX 17.89 SUPRA + L 9.9 Temperature : 45 to 65 C 5 OXIDATION and OILS H.S.S. HARD METAL LINE ACID CLEANER + L See data sheet 6 PROTECTION ANTI OXIDATION (in final DI water) KORROSTOP 5000 + L 12.3 Concentration : 0,02 to 0,1% Temperature : 20 to 30 C Time : 2 to 3 min 7 LINE TUMBLING BRASS COPPER ALLOYS TRIBO See data sheet LEGEND: + : BIODEGRADABLE - : NON BIODEGRADABLE L/P : LIQUID or POWDER : ULTRASONIC n.m. : NON MEASURABLE www.ngl-cleaning-technology.com PAGE 3
PRODUCTS To remove From Recommended product +/- L/P ph Instructions for use 8 VARNISH LACQUER PITCH SYNTHETIC STONES ALLSTRIP + L n.m. Concentration : 100% Temperature : 20 to 40 C Time : 2 to 10 min 9 ZAPON RUBIFIN N 4N + L n.m. Concentration : 100% Température : 20 to 40 C Time : 3 to 10 min 10 ANTI SCRATCH LACQUER SCHUTZLACK NGL - L n.m aerosol : SCHUTZLACK NGL 2002 ROSE spray or dipping : SCHUTZLACK NGL 2005 ROSE SPL 11 (TO SUBSTITUTE SOLVENT) GREEN LINE BIO-TOP 10 + L 7.5 Concentration : 2 to 10% Temperature : 25 to 60 C Time : 2 to 10 min. GRINDING & POLISHING COMPOUNDS (MANUAL CLEANING) GREEN LINE NEOCLEAN SUPER + L 10.5 Temperature : 65 C Time : 3 to 10 min FLUX 12 ELECTRONICS PCB S RACK CLEANER NGL 17.13 SUPER - L 9.3 Temperature : 45 to 65 C LEGEND: + : BIODEGRADABLE - : NON BIODEGRADABLE L/P : LIQUID or POWDER : ULTRASONIC n.m. : NON MEASURABLE www.ngl-cleaning-technology.com PAGE 4
NGL EQUIPMENT Objectif Equipement Principe 13 Measuring of physicalchemical parameters having an influence on the cleaning quality 14 Simple and quick control of rinsing water quality UPC 3000 ULTRASONIC PROCESS CONTROLLER ACC 2000 ACQUA CLEAN CONTROL Simple and quick control of the parameters with 3 sensors (Complete documentation at request). Enables a quick optional control of Di water quality. It complements conductivity measurement. 15 Waste water processes prior to disposal 16 Impurities precipitation system DECOFLOC 770 DECOFLOC 660 DECOFLOC HF DECOFLOC MB Easy separation of solid particles from aqueous fluids (quartz, cerium and aluminium oxides, silicium carbide). Only one reagent with unique properties. insolubility of metals agent for coagulation agent for flocculation NGL Chemicals-Environment : The Right Connexion DECOFLOC IPS (Impurities Precipitation System) nonstop treatment process mechanico-chemical polishing waste cutting waste rectification and milling emulsions PAGE 6
PIONEER IN HIGH PRECISION CLEANING PROCESSES FOR THE HIGH-TECH PROCESS RELIABILITY ISO 9001 CERTIFICATE SQS No. 11443 ISO 14001/ OHSAS 18001 CERTIFICATE SQS No. 30865 DISTRIBUTEUR: 7, Ch. de la Vuarpillière CH 1260 NYON - Switzerland Tél.+41(0) 22 365.46.66 Fax: +41(0) 22 361.81.03 Web: www.ngl-cleaning-technology.com A - MARCH 2011