THE EFFECT OF BLENDING A RATIO OF EGYPTIAN CHORISIA SPP. FIBERS WITH COTTON AND POLYESTER WASTES ON SOME PROPERTIES OF THE YARNS



Similar documents
1370 EFFECT OF BLENDING EGYPTIAN AND UPLAND COTTONS ON O.E. YARN QUALITY

Evaluation of Egyptian cotton variety (Giza 90) and promising cotton cross for yarn characters

COMPARISON BETWEEN MECHANICAL PROPERTIES OF FABRICS WOVEN FROM COMPACT AND RING SPUN YARNS

Impacts of Fiber Length Distribution on Market Value and Yarn Quality: Implications for U.S. Cotton Eric F. Hequet M.

Ingeo Fibre Apparel Product Guidelines. Fiber to Fabric. 1. Introduction to Ingeo fibers 2. Fiber to yarn 3. yarn to fabric

Methods for investigation of yarn structure and properties

Compact Spinning for Improved Quality of Ring-Spun Yarns

Card Fibre Transfer Test ver 1.0. Pc-Program Application BY ITRU GROUP LTD

VISCOSE FIBRES WITH NEW FUNCTIONAL QUALITIES

The Effect of Fiber Twist on the Mechanical Properties of Natural Fiber Reinforced Composites

Predicting Yarn Quality Performance Based on Fibers types and Yarn Structure. N. A. Kotb

Dispersion of Synthetic Fibers in Wet-Lay Nonwovens

INVESTIGATION OF MECHANICAL PROPERTIES OF POLYESTER REINFORCED WITH HEMP FIBRE (LONG FIBRES AND MAT) FOR PATELLAR IMPLANT APPLICATION

Effect of Lycra Extension Percent on Single Jersey Knitted Fabric Properties

Ring-spinning processing

CCS COTTON CLASSIFYING SYSTEM

Choosing The Proper Short Cut Fiber for Your Nonwoven Web

Composite Materials. Mary P. Shafer. Fabric Development, Inc. Quakertown, PA 18951

Influence of Mercerization on Micro-structure and Properties of Kapok Blended Yarns with Different Blending Ratios

How To Improve Mechanical Properties Of A Composite Material

Influence of Nozzle Type on Yarn Quality in Open-End Rotor Spinning

Tearing strength of cotton fabrics in relation to certain process and loom parameters

A STUDY ON BONDING STRENGTH OF POLYMERIC FIBERS TO CEMENTITIOUS MATRIX

Wrapper Fibres in Open-End Rotor-Spun Yarns: Yarn Properties and Wrapper Fibres

TEXTILE FABRICS AS THERMAL INSULATORS

RAINBOW: A NOVEL VISCOSE FIBER FOR PES BLENDS INNOVATIONS IN DYEING TECHNOLOGY

Card C 60. The concept for excellence

Structural Integrity Analysis

YARN TENSION IN THE PROCESS OF ROTOR SPINNING

Every picture tells a story...

The Advantages of Flax Fibers in Composites June 2009, Frankfurt. Medical Industrial Automotive Filtration Apparel June 2009 Page 1

About OMICS Group Conferences

Yarns. Definition of Yarn. Classification: * Types of Yarn. Yarns may be: In addition, Filament yarns may be: From fibers to yarns

Besides the aesthetic properties, mechanical and

TF: TEXTILE ENGINEERING AND FIBRE SCIENCE

COMPARISON BETWEEN GLASS AND FLAX NON-CRIMP STITCHED FABRICS

Biocomposites Properties and Applications

Numerical Analysis of Independent Wire Strand Core (IWSC) Wire Rope

Effect of basalt aggregates and plasticizer on the compressive strength of concrete

Analysis of M35 and M40 grades of concrete by ACI and USBR methods of mix design on replacing fine aggregates with stone dust

Design, Manufacturing of a New Laboratory Type Filament Yarn Drawing Machine and Featured Yarn Development Studies

Properties of Fibers and Fabrics Luke Ferguson, Ph.D. Materials Education Associates Seattle, WA

REGULATIONS AND SYLLABUS FOR Executive Training Course On Jute Technology and Management

Mold Preventing I nterior System

Broad Base. Best Solutions. SIGRAFIL Continuous Carbon Fiber Tow

Lab 1 Concrete Proportioning, Mixing, and Testing

Non- Carbon Fiber Electrical Heating Textile Introduction:

Naue GmbH&Co.KG. Quality Control and. Quality Assurance. Manual. For Geomembranes

rhuesker HUESKER HUESKER HUESKER HUESKER HUESKERr HUESKER HUESKER HUESKER HUESKERHUES Product- Portfolio HUESKER Engineering with Geosynthetics

MATERIALS AND MECHANICS OF BENDING

Statistical Model for Predicting Compressed Air Consumption on Air-Jet Looms

Metal Injection Molding (MIM) of components made of Titanium and its alloys

MaxCell Technical Manual Design Parameters

Innovative textile - industrial cluster of the Ivanovo region

LABORATORY EXPERIMENTS TESTING OF MATERIALS

AGRICULTURAL COVERING

NAN YA NYLON 66 Engineering Plastics. Flame Retardant.High Toughness.Heat Resistant. Impact Resistant.Moldability.Low Warpage

USE OF CFRP LAMINATES FOR STRENGTHENING OF REINFORCED CONCRETE CORBELS

Created by Neevia Document Converter trial version Created by Neevia Document Converter trial version

Stabilenka HUESKER. and Separation. Engineering with Geosynthetics SKER HUESKER HUESKER HUESKER HUESKERHUES


SINCE 1947 IN THE VAN OF BUFFING MACHINES

Selective Laser Sintering of Duraform TM Polyamide with Small-Scale Features

Textile Merit Badge Workbook

Stress Strain Relationships

Only nature imprints so well

EVALUATION OF THE CARE AND PERFORMANCE OF COMFORT STRETCH KNIT FABRICS. Introduction

Development of Prediction Systems Using Artificial Neural Networks for Intelligent Spinning Machines

STUDY ON COMFORT CHARACTERISTICS OF HIGH ACTIVE SPORTSWEAR

EGYPTIAN COTTON PRODUCTION TO MEET THE EXTRA LONG STAPLE COTTON REQUIREMENT IN THE COUNTRY. K.N. Gururajan

Right Angle Grinder USA MADE FLAP DISCS

GRADATION OF AGGREGATE FOR CONCRETE BLOCK

NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB x Replaces GB Anti-static protective clothing

EFFECT OF SCOURING AND BLEACHING TREATMENT ON KNITTED COTTON FABRICS FOR ECONOMIC STUDY

VISCOSTAR - A STAR-SHAPED VISCOSE FIBER FOR IMPROVED ABSORBENCY

Manufacturing Quality Concrete Products

MYSA. Quilts BUYING GUIDE

Pile Seal for insect screen

Effects of Fiber Denier, Fiber Cross-Sectional Shape and Fabric Density on Acoustical Behavior of Vertically Lapped Nonwoven Fabrics

Fixapret NF. Technical Information

The Strength of Concrete

UGVCL/SP/591/11KV HT AB CABLE

ENGINEERED QUARTZ STONE

TENCEL HIGH PERFORMANCE SPORTSWEAR

Derakane epoxy vinyl ester resins: The Evolution of Corrosion Resistant FRP

INJECTION MOULD DESIGN: MARPLEX PVC RESINS

Araldite LY 3505* / Hardeners XB 3403* / Hardener XB * / Aradur 3405*

BKP Berolina Polyester GmbH & Co. KG. Berolina-Liner System Lightspeed in gravity pipe rehabilitation!

CIVIL ENGINEERING. Sewage Pipe System. POLO-ECO plus PREMIUM 12. POLO-ECO plus PREMIUM 10

Dubai Municipality Standard DMS 1: Part 5: 2004

Therefore, the pilling effect always will be avoided, and should be taken into account from initial conception of the fabric:

EXPERIMENTAL INVESTIGATION ON BEHAVIOUR OF NANO CONCRETE

Strength and Workability Characteristics of Concrete by Using Different Super Plasticizers

EVALUATION OF MECHANICAL PROPERTIES OF BIODEGRADABLE PACKAGING MATERIALS

Stone crusher dust as a fine aggregate in Concrete for paving blocks

Study on dyeing behavior of cotton/organic cotton knitted fabrics D. Raja 1, A.Arputharaj 2, C. Prakash 1, V.Ramesh Babu 1 and C.V.

EXPERIMENTAL INVESTIGATION ON STRENGTH AND DURABILITY PROPERTIES OF HYBRID FIBER REINFORCED CONCRETE

Construction. 3-part thixotropic epoxy patching mortar. Product Description. Tests

CENTRIFUGAL CASTING.

Guide Specification STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM

Transcription:

THE EFFECT OF BLENDING A RATIO OF EGYPTIAN CHORISIA SPP. FIBERS WITH COTTON AND POLYESTER WASTES ON SOME PROPERTIES OF THE YARNS Amal Mohamed EL-Moursy¹, Abeer Ibrahim Mohamed² ¹ ²Department of Textile Technology, Faculty of Industrial Education University of Beni Suef, Egypt ABASTRACT: This research may be the first to use the hollow fibers that are rarely grown trees though they are found in Egypt and in many countries of the world under many types such as chorisia, bombax, kapok and java, and some of these types exist in Egypt but the most famous are the chorisia spp. trees. the organizations did not pay attention for the fibers of these trees but they pay attention for using it in the medical field. These fibers are light, very smooth, short and free of convolutions. They are not immature fibers, so when they are spun they must be blended with other fibers. This research sheds light on blending chorisia fibers with cotton and polyester wastes to make two blends, the first of which using ratios of 7% cotton wastes and 3% polyester wastes and the second using the ratios of 4% korisia, 3% cotton wastes and 3% polyester wastes were spun using the open-end spining to produce yarn counts 6/1 13/1. Tests on yarns produced such as tensile strength, elongation, the proportion of yarn irregularity and yarn imperfections were carried out and the results in the two blends were compared. One of the most important results is low tensile values, high ratios of elongation, imperfections and yarn irregularity c.vm% in the second blend which contains chorisia fibers from those in the first blend, which contains no chorisia. Keywords: Blending, Chorisia Fibers, Cotton Wastes, Imperfection/ Km, Polyester Wastes I. INTRODUCTION Chorisis spp. is a tree that produce chorisia fibers that considered a hollow fibers such as kapok tree and bombax tree, their family is Bombacaceae [1--3] these fibers are natural cellulose and have smooth silky surface [4-5] Many researchers studied chemical and physical compositions of kapok[3--5] and bombax [6-7]. Hollow fibers used in many fields such as wadding [8 ], blended yarns [5,9,1 ] and fabrics products [11-12]. Bombax, kapok and chorisia impossible to spun separately due to short length,low density and very smooth surface[4-5] so that they should be blended with other fibers like cotton, polyester[5-9], polypropylene[12] and sisal[13].. etc.in a research the blended yarns cotton / kapok were produced using different blending ratios of 8: 2, 7: 3, 6:4and 5: 5% where they were produced with rotor spinning. One of the most 15 P a g e

important results that by increasing the ratio of kapok both tensile strength and quality of yarns decreased [5]. After a period of time the ring [9, 14]and compact spinning were produced for the production of blended yarns.in other research the blended yarns were collected from various manufactures these yarns content 14 type of kapok blended yarns and 4 types of cotton yarns at different blending ratios that manufactured through rotor, ring and compact spinning. then measured yarn fineness/unevenness, yarn defects, yarn hairiness, and breaking tenacity, then comparing between the results of the quality of kapok blended yarn, It was found that the compact spinning produced the higher quality of the blended yarn [ 9 ]. another research made blended yarns of kapok/ cotton ratios of 7:3%, 6:4%,4:6%, count yarns 28 tex and 28 tex 1% cotton then the yarns were treated by mercerization process with a solution of NaOH with various concentrations : 18g/L, 22g/L, 25g/L, 28g/L.[1] The research results are that the mercerization influenced the properties of blended yarns containing a ratio of Kapok[1,15]. When the alkali concentration increased from 18 g/l to 25g/L, the strength of treated blended yarns increased and elongations at breaking decreased. When alkali concentration reached to 28 g/l, the strength of blended yarns with high content of kapok fibers decreased and elongation increased [1] Mercerization treatment had little or no apparent effect on the chemical composition of the blended yarns containing kapok fibers,but led to decreasing on crystallinity of the blended yarns, and parts of cellulose I were transformed into cellulose II [1,15]. chorisia spp. Trees were planted in different places in Egypt, they are considered medical plants and they are used in the pharmacy field [ 16-17]. Most of the researches used the bombax and kapok fibres to produce yarns and fabrics but this research will use the egyptian chorisia fibrer and bleded it with a certain ratio with the wastes of polyester and cotton to improve the chorisia properties and use less amounts of egyptian cotton especially that the chorisia have lots of seeds and their production is great. In a certain season the chorisia trees are harvested. these trees have less cost in their cultivation and in converting them to yarns. II. EXPERIMENTAL 2.1 Materials Egyptian chorisia spp. fibers considered a hollow fibers. It was used and blended with cotton wastes and polyester wastes to make two blends. 2.2 Preparation of blending samples The first blend consists of 7% cotton wastes and 3% polyester wastes.the second blend 4%chorisia, 3% cotton and 3% polyester. From the previous two blends three count yarns will be produced. In the second blend chorisia fibers was blended in chute feed with cotton wastes and polyester wastes to produce card sliver then drafting them then The draft sliver will be spun 2-2-1 The specifications of samples yarns Produced 6 single yarns samples of count 6/1, 13/1and from two blends and specifications as shown in table 1 151 P a g e

2-2-2 The specifications of spinning machine It has been produced yarns on the Open- End Spinning machine of two blends and machine specifications were as follows: Machine kind Schlafhourst German Rotor speed 42 rpm Opening roller 85 rpm rotor Diameter 45 mm Table 1 The specifications of the blended yarns No Yarns material yarns blending ratio yarn count yarn Twist/inch Ne 1 Cotton wastes 7% Cotton wastes 6/1 14 2 Polyester wastes 3%Polyester wastes 13/1 21 3 17/1 24 4 chorisia 4% chorisia 6/1 14 5 Cotton wastes 3%Cotton wastes 13/1 21 6 Polyester wastes 3%Polyester wastes 17/1 24 2-3 Testing of the yarns Laboratory tests on the produced yarns samples were carried out at the standard conditions for textiles with an air temperature ( 2 ± 2 C) and relative humidity of air (65± 5% ) according to the American society of testing materials (ASTM ). 2-3-1 Tensile strength g/f and elongation % of yarns : The yarns Tensile strength, elongation and tenacity were measured and the test was carried out on the 1, meters for each yarn by the device Uster 3 2-3-2 Yarn imperfection / km and C.Vm %, thick and places values and C.Vm % were measured by Uster 4 III. RESULTS AND DISCUSSION After the production of yarns from the two blends and testing it was noted marked differences as a result of the blending ratios of chorisia, Confirms that chorisia has an effect on the properties of the yarns.table 2 shows the results of tests 152 P a g e

tensile strength g/f No 1 2 3 4 5 6 Table 2 : The results of testing the samples of the blended yarns yarns blending Yarn Tensile Elongation Yarn imperfection/ km ratio Count strength % -5% km Ne g / f 7% Cotton 6/1 1338 13.58 3% Polyester 13/1 578 1.8 17/1 381 9.8 1 4 % chorisia 6/1 1193 14.69 3 % Cotton 13/1 392 11.28 3 3 % Polyester 17/1 288 1.21 9 +5% km +28%km 6 6 25 14 35 22 25 1 36 25 4 27.5 C.Vm% 11.8 13.86 14.51 18.21 14.19 17.45 3.1 The Effect of blending on the Fiber Tensile Strength g/f and Yarn Elongation % Table 2 and Fig. 1 show that the tensile strength for all yarns in the second blend scored lower values than that in the first blend at the same yarn counts. This is due to the presence of chorisia fibers by 4% of the blending ratio since they are not fully grown fibers as the hollow inside the fiber is greater than its wall consisting of deposited cellulose layers and thus the tensile strength of the fiber is low thus resulting in a lower tensile strength. In addition, the chorisia fibers are very soft and it has no convolutions and it is light and short length and all this leads fibers to slide within the yarn structure so that not all the fibers are arranged in the longitudinal direction of the yarn, which reduces its tensile strength. Yarn elongation in the second blend, as shown in Fig. 2 scored higher values than that in the first blend at the same yarn counts. The reason is that the chorisia fibers are light, easy to bend and the fibers may be in the cross position as a result of sliding. All this leads to an increase in elongation of yarns when they are under tension. 14 12 7% Cotton - 3% Polyester 4% Chorisia - 3% cotton - 3% Polyester 1 8 6 4 2 yarns blending ratio % Figurer I. The effect of blending on the tensile strength g/f of yarns 153 P a g e

Elongation % 16 14 12 1 7% Cotton - 3% Polyester 4% Chorisia - 3% Cotton - 3% Polyester 8 6 4 2 Yarns blending ratio % Figure 2. The effect of blending on the elongation % of yarns 3.2 The Effect of Blending on the Yarn Imperfection /km In the second blend as shown in Fig. 3 thick places scored higher values than those scored by their corresponding in the first blend at the same yarn counts. The reason for this is the presence of chorisia fibers with a great difference in fiber thickness. The thick places also scored high values with low thickness of the yarn (greater yarn count) where the thick yarns have greater number of fibers which reduces the number of thick places in the yarn and the opposite happens for the thin yarns. For high neps values in the second blend as shown in Fig. 3 this is due to the presence of hairiness intertwined on the surface of the yarn forming neps. In addition, the cotton and polyester wastes that basically contain neps, which increase in the presence of chorisia fibers that are easy to bend and slide. It was also noted that the ratio of neps increases with greater yarn count for the same reason previously explained. For thin places as shown in Table 2 they scored values only at yarn count 17/1 in the first blend. They also scored values in the second blend at yarns counts 13/1 and 17/1. That is, thin places appear when the yarns thickness is low. 3.3 The Effect of Blending on the Ratio of Yarn Irregularity c.vm% In the second blend as shown in Fig. 4 c.vm.% scored higher values than those scored by their corresponding in the first blend at the same yarn counts. Notably, the high ratio of c.vm% in the two blends, because blending cotton and polyester wastes with chorisia fibers result in a higher c.v.% value in the second blend. The fibers always undergo a disorder, leading to the difference in the number of fibers in the yarn cross-section in addition to the difference of fibers fineness in the same material. All this led to irregularity of yarns and the appearance of imperfections. The c.vm% values rises with increasing the yarn count in the two blends. 154 P a g e

Yarns irregularity c.vm % Yarn imperfiction/km 4 Blending 1 Blending 2 35 3 25 2 15 1 5 (-5% km ) (+5% (+28% (-5% (+5% (+28% (-5% (+5% (+28% Figure 3. The effect of blending on the yarn imperfection / km Blending 1 = 7 % cotton-3% polyester Blending 2= 4%chorisia- 3%cotton-3%polyester 2 18 16 14 7% Cotton - 3% Polyester 4% Chorisia - 3% Cotton - 3% Polyester 12 1 8 6 4 2 Yarns blending ratio % Figure 4. The effect of blending on the yarn c.vm % IV. CONCOLUSION The presence of chorisia fibers in the blend leads to a lower tensile strength, yarn quality and regularity. chorisia fibers have led to improving the yarn elongation. They can be used as wefts or blend with many other wastes or raw materials. 155 P a g e

The cotton ratio can be dispensed with and replaced by chorisia fibers, thus saving the cotton. The advantages of these fibers include: they do not need a ginning process, or passing on the opening and cleaning line or beaters, their seeds are easy to get rid of and this leads to saving energy and thus reduces costs. This can also open new venues for researches on this material to make advantages of them larger with making amendments in the production line to suit the nature of this material. REFERENCES [1] Anigo, K.M., DAauda, B.M.D.,Sallau, A.B.,Chemical composition of kapok (ceibapentandra) seed and physicochemical properlies of its oil, Nigeran journal of basic and applied science, 21(2),213,15-18. [2] Rameshwar, V.,Kishor,D.,and others, Apharmacognostic and pharmacological overview on bombax ceibe, Scholars Academic Journal of pharmacy, 3(2),214,1-17 [3] Zheng, Y.,Wang,J.,and others,research and application of kapok fiber as an absorbing material : Amini review, Journal of environmental scinces, 26, 214, 21-31 [4] Dhanabalan,V.,&Laga,S.K., Kapok fibre : Aperspective fibre, 215 http:/ www.slidshare. [5] Dauda,B.M., &Kolawole, E.G., Processibility of Nigerian kapok fibre,indian journal of fibre & textile research, 28, 23, 147-149. [6] Zhang,L., He, J.,& Wang, S. Y.,Structure and thermal properties of natural colored cottons and bombax cotton, Journal of thermal analysis and calorimetry, 95(2), 29, 653-659. [7] Audu-peter, J., Vandi, J.,Wunidah, B., Evaluation of some physicochemical properties of bombax gum, Journal of pharmacy & Bioresources, 6(2), 29, 38 42. [ 8] Ying, L., Fumei, W., Wei, L., Compressibility of kapok wadding, Journal of textile research, 27. [9] Yan, J., Xu, G., Wang,F., A study on the quality of kapok blended yarns through different processing methods, The journal of the textile institute, 14 (7), 213, 675-681. [1] Liu, J., Wang, F., Influence of mercerization on micro-structure and properties of kapok blended yarns with different blending ratios, Journal of engineered fibers and fabrics, 6 (3), 211, 63 68. [11] Uzumcu, M., Ute, T. and others, properties of knitted fabrics produced by kapok blended yarns, World journal of engineering, 9 (5), 212, 451 454. [12] Veerakumar, A., Selvakumar, N., A preliminary investigation on kapok/polypropylene non woven composite for sound absorption, Indian journal of fibre and textile research, 37, 212, 385 388. [13] Reddy, V., G., Naidu, V., S., Rani, S., T., A study on hardness and flexural properties of kapok/sisal composites, Journal of reinforced plastics and composites, 28 (16), 29, 235 244. [14] Li, E. S., Xia, Q. L., A manufacturing methods of ring spinning kapok blended yarn, [ p ] china, 936135, 27, 3 28. [15] JieL., fumei, W.,The effect alkali treatment on structure and properties of yarns containing kapok fibers, Journal of textile research, 12, 29 [16] El Alfy, T., El Sawi, S., El Tawab S., Moawad, D., pharmacognostical study of chorisia insignis HBK. grown in Egypt. Bulletin of Faculty of Pharmacy, Cairo University 5, 212, 17 39. [17] Refaat., J., Desouky, Y., S., and others, Rhoifolin : A review of sources and biological activities, nternational journal of pharmacognosy, 2 (3), 215, 12 19. 156 P a g e