This European technical approval

ÖSTERREICHISCHES I N S T I T U T F Ü R B A U T E C H N I K A-1010 Vienna, Schenkenstrasse 4 Tel.: + 4 3 ( 0 ) 1-5 3 3 6 5 5 0 Fax: + 4 3 ( 0 ) 1-5 3 3 6 4 2 3 relating to construction products E - m a i l : m a i l @ o i b. o r. a t Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the a p p r o x i m a t i o n o f l a w s, regulations and administrative provisions of Member States European technical approval ETA-06/0076 (English language translation, the original version is in German language) Handelsbezeichnung Trade name Clima-super, Isocell, trendisol, Isodek, Dobry - Ekovilla, FibraNatur, France-Cellulose, Qualicell, Cellaouate, Ouattitude, Domexcell, Pavafloc, Renocell Zulassungsinhaber Holder of approval ZELLULOSEDÄMMSTOFFPRODUKTION CPH Beteiligungs GmbH & Co KG Am Ökopark 6 8230 Hartberg Zulassungsgegenstand und Verwendungszweck Generic type and use of construction product Dämmstoff aus losen, ungebundenen Zellulosefasern Insulation material made of loose, free cellulose fibres Geltungsdauer vom Validity from bis to Herstellwerk Manufacturing plant Diese Europäische technische Zulassung umfasst This European technical approval contains Diese Zulassung ersetzt This approval replaces 26.04.2011 25.04.2016 PLANT 1, PLANT 2, PLANT 3 11 Seiten einschließlich 0 Anhängen 11 pages including 0 Annexes ETA-06/0076 mit Geltungsdauer vom 18.12.2009 bis zum 25.04.2011 European Organisation for Technical Approvals Europäische Organisation für Technische Zulassungen Organisation Européenne pour lʼagrément technique

of European technical approval ETA-06/0076, I LEGAL BASES AND GENERAL CONDITIONS 1 This European technical approval is issued by Österreichisches Institut für Bautechnik in accordance with: Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products1, modified by the Council Directive 93/68/EEC of 22 July 19932; dem Gesetz vom 20. März 2001 über das Inverkehrbringen und die Verwendbarkeit von Bauprodukten (Steiermärkisches Bauproduktegesetz 2000) LGBl. Nr. 50/2001, in der Fassung LGBl. Nr. 85/2005 und in der Fassung LGBl. Nr. 13/2010; Common Procedural Rules for Requesting, Preparing and the Granting of European technical approvals set out in the Annex of Commission Decision 94/23/EC3. 2 The Österreichisches Institut für Bautechnik is authorized to check whether the provisions of this European technical approval are met. Checking may take place in the manufacturing plant. Nevertheless, the responsibility for the conformity of the products to the European technical approval and for their fitness for the intended use remains with the holder of the European technical approval. 3 This European technical approval is not to be transferred to manufacturers or agents of manufacturers other than those indicated on page 1, or manufacturing plants other than those indicated on page 1 of this European technical approval. 4 This European technical approval may be withdrawn by the Österreichische Institut für Bautechnik, in particular after information by the Commission on the basis of Article 5 (1) of Council Directive 89/106/EEC. 5 Reproduction of this European technical approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of the Österreichisches Institut für Bautechnik. In this case partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European technical approval. 6 The European technical approval is issued by the approval body in its official language. This version corresponds to the version circulated within EOTA. Translations into other languages have to be designated as such. 1 2 3 Official Journal of the European Communities N L 40, 11.02.1989, p. 12 Official Journal of the European Communities N L 220, 30.08.1993, p. 1 Official Journal of the European Communities N L 17, 20.01.1994, p. 34

of European technical approval ETA-06/0076, II SPECIFIC CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL 1 Definition of products and intended use 1.1 Definition of products This European technical approval applies to the following insulation product made of loose, free cellulose fibres: Clima-super, Isocell, trendisol, Isodek, Dobry - Ekovilla, FibraNatur, France- Cellulose, Qualicell, Cellaouate, Ouattitude, Domexcell, Pavafloc, Renocell This product consists of cellulose fibres made from waste paper by mechanical crushing. During this manufacturing process the fibres are provided with a fire protection equipment and serves for the production of insulation layers by means of machine processing. The machine processing is carried out in dry condition. The insulation product is depending on the area of application and processing produced with different densities (density range 28-65 kg/m³). The waste paper used in the manufacturing process has to fulfil the following quality criteria: Paper according to the European list of standard grades of recovered paper and board recovered paper grade EN 643-2-01-00. 1.2 Intended use The insulation product made of cellulose fibres is used as non loadable insulating material mainly for intended uses where vertical or horizontal cavities are completely filled or horizontal, arched or moderately pitched ( 10 ) exposed areas are covered. Area of application for walls Machine processed cavity insulation material for exterior walls Machine processed cavity insulation material for interior walls Area of application for roofs Machine processed cavity insulation material for pitched roofs without ventilation (full rafter insulation) Machine processed cavity insulation material for flat roofs with upper covering and non ventilated cavity under the waterproofing Area of application for ceilings / floors Machine processed exposed insulation material not subject to foot traffic for ceilings under non habitable attics (thermal insulation layer between or above the loadbearing structure) Machine processed cavity insulation material between floor-joists under floor constructions for insulation or cavity damping The insulation product made of cellulose fibres shall not be used in structures where it will be exposed to wetting or weathering. The corrosion developing capacity of the insulation product has not been determined. Suitable measures might be necessary to avoid corrosion of metal parts of the construction in contact. The provisions made in this ETA are based on an assumed intended working life of the insulation product of 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer, but are to be regarded only as a means for

of European technical approval ETA-06/0076, choosing the right product in relation to the expected economically reasonable working life of the works. 2 Characteristics of products and methods of verification 2.1 Composition and manufacturing process The insulation product shall as far as its composition and manufacturing process is concerned correspond to the product subject to the approval tests. Details of composition and manufacturing process are deposited at the Österreichischen Institut für Bautechnik. 2.2 Density The density of the insulating materials is determined according to standard ISO/CD 18393 4. Depending on the area of application the density ranges stated in Table 1 are to be observed and controlled by the installer. Table 1: density range depending on the area of application area of application density range kg/m³ Vertical: machine processed cavity insulation in exterior-, interior walls, 38-65 Pitched: machine processed cavity insulation in roofs (pitch >10 ) 38-65 Horizontal: machine processed cavity insulation in flat roofs and floor constructions 38-65 Horizontal: machine processed exposed insulation not subject to foot traffic on ceiling constructions 28-40 (pitch 10 ) 2.3 Settlement The settlement is determined according to ISO/CD 18393 4 following the test methods stated in Table 2. The maximum values of settlement stated in Table 2 are not exceeded for the given minimum density. Table 2: Settlement depending on the test method Test method according to ISO/CD 18393 settlement density settled density % kg/m³ kg/m³ Method A Settling by impact excitation 8 31,0 33,0 Method C Settling of wall cavity insulation by vibration 0 38,0 38,0 Method D Settling by specified climatization 10 33,0 34,0 2.4 Water absorption No performance determined 2.5 Water vapour diffusion resistance factor The water vapour diffusion resistance factor µ =1 (see 4.2.1.1). 4 ISO/CD 18393:2002-08 Thermal insulation Accelerated ageing of thermal insulation materials Assessment of settling of loose-fill thermal insulation used in attic and closed cavity applications

of European technical approval ETA-06/0076, 2.6 Airflow resistance The airflow resistance of the products is determined according to European standard EN 29 053, method A 5, The mean longitudinal airflow resistance at a density of 30/50 kg/m³ is at least 5,3/25,1 kpa s/m². 2.7 Thermal conductivity The thermal conductivity of the products is determined according to EN 12667 6. The declared value of thermal conductivity is determined according to EN 10 456 7. The fractile value of thermal conductivity for the density range of 28 kg/m³ - 65 kg/m³ is (10,dry,90/90) = 0,0371 W/(m K) representing at least 90 % of the production with a confidence limit of 90 %. The limit value of thermal conductivity for the density range of 28 kg/m³ - 65 kg/m³ is (10,dry,limit) = 0,0370 W/(m K) representing the total production. The manufacturer is responsible for keeping the limit during production. The declared value of thermal conductivity for the density range of 28 kg/m³ - 65 kg/m³ is D(23,50) = 0,039 W/(m K) category 1 determined by conversion of the (10,dry,90/90) value. The declared value of thermal conductivity for the density range of 28 kg/m³ - 65 kg/m³ is D(23,50) = 0,039 W/(m K) category 2 determined by conversion of the (10,dry,limit) value. For conversion of humidity the following applies: the moisture content mass by mass at 23 C/50 % relative humidity: u 23,50 = 0,068 kg/kg the moisture content mass by mass at 23 C/80 % relative humidity: u 23,80 = 0,111 kg/kg the moisture content conversion coefficient mass by mass: f u1 (dry 23/50) = 0,47 kg/kg f u2 (23/50 23/80) = 0,58 kg/kg 5 6 7 EN 29 053: 1993-03: EN 12667: 2001 EN ISO 10 456: 2000: Acoustics - Materials for acoustical applications - Determination of airflow resistance Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance Thermal insulation - Building materials and products - Determination of declared and design values

of European technical approval ETA-06/0076, 2.8 Reaction to fire The reaction to fire of the insulation products is tested by using the test methods relevant for the corresponding reaction to fire class and is classified according to EN 13 501-1 8. Table 3 shows the reaction to fire classes which apply to the insulation products as a function of their end use application. Table 3: Reaction to fire classes as a function of the end use application End use application installation density of the insulating material 30 kg/m³ to 65 kg/m³, insulation layer thickness 100 mm; end use application without air gap end use application substrates defined in EN132389 for the following standard substrate: wood based panel : density of the board 680 50 kg/m³, board thickness 12 2 mm, reaction to fire of the board: class D, calcium silicate board : density of the board 870 50 kg/m³, board thickness 11 2 mm, reaction to fire of the board: class A2 installation density of the insulating material 30 kg/m³ to 65 kg/m³, insulation layer thickness 40 mm 2.9 Resistance to biological actions Reaction to fire: Class B-s2,d0 The test and the assessment of the resistance to growth of mould fungus has been verified according to the EOTA testing procedure (Annex C of CUAP In-situ formed loose filled thermal insulation material and/or acoustic insulation material made of vegetable or animal fibres; edition July 2009 ). The reached class of the product is 0. 2.10 Corrosion developing capacity on metal construction products No performance determined. 2.11 Retention of additives The test and the assessment of the retention of additives has been verified according to the EOTA testing procedure (Annex F of CUAP In-situ formed loose filled thermal insulation material and/or acoustic insulation material made of vegetable or animal fibres; edition July 2009 ). Neither decrease in the reaction to fire behavior nor resistance to mould growth was determined. 2.12 Dangerous substances The product consists of cellulose fibres made from waste paper by mechanical crushing under addition of flame retardants and complies with the provisions of guidance paper H 10. It does not contain substances which have to be classified as dangerous according to Directive 67/548/EEC and/or listed in the "Indicative list on dangerous substances" of the EGDS and can be classified as product type 2 according the EOTA testing procedure (clause 4.3.2 of CUAP In-situ formed loose filled thermal insulation material and/or acoustic insulation material made of vegetable or animal fibres; edition July 2009 E 8 9 10 EN 13 501-1:2002-06: EN 13238:2001: Guidance paper H: Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests Reaction to fire tests for building products Conditioning procedures and general rules for selection of substrates A harmonised approach relating to Dangerous substances under the construction products directive, 18 February 2000

of European technical approval ETA-06/0076, A declaration of conformity in this respect was made by the manufacturer. In addition to the specific clauses relating to dangerous substances contained in this European technical approval, there may be other requirements applicable to the products falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction Products Directive, these requirements need also to be complied with, when and where they apply. 2.13 Critical moisture content No performance determined 3 Evaluation of conformity and CE marking 3.1 Attestation of conformity system System 3 for Clima-super, Isocell, trendisol, Isodek, Dobry - Ekovilla, FibraNatur, France-Cellulose, Qualicell, Cellaouate, Ouattitude, Domexcell, Pavafloc, Renocell 3.1.1 for which the following is valid: intended use any reaction to fire classes E The system of attestation of conformity is described in Council Directive (89/106/EEC) Annex III, 2 (ii), Second possibility and is detailed as follows: a) Tasks of the manufacturer factory production control. b) Tasks of the approved body initial type-testing of the product System 1 for Clima-super, Isocell, trendisol, Isodek, Dobry - Ekovilla, FibraNatur, France-Cellulose, Qualicell, Cellaouate, Ouattitude, Domexcell, Pavafloc, Renocell 3.1.2 for which the following is valid: reaction to fire classes B considering that a clearly stage in the production process has been identified which results in an improvement of the reaction to fire classification (addition of fire retardant) The system of attestation of conformity is described in the Council Directive 89/106/EEC Annex III, 2 (i), First possibility and is detailed as follows: Certification of the conformity of the product by a notified certification Body on the basis of: a) Tasks of the manufacturers: factory production control further testing of samples taken at the factory by the manufacturer in accordance with a control plan

of European technical approval ETA-06/0076, b) Tasks of the Notified Body: initial type-testing of the product initial inspection of factory and of factory production control continuous surveillance, assessment and approval of factory production control 3.2 Responsibilities 3.2.1 Tasks for the manufacturer; factory production control The manufacturer has a factory production control system in his plant and exercises permanent internal control of production. All the elements, requirements and provisions adopted by the manufacturer are documented in a systematic manner in the form of written policies and procedures. The factory production control system ensured that the products are always in conformity with the European technical approval. In the framework of factory production control the manufacturer shall carry out tests and controls in accordance with the control plan 11 which is fixed with this European technical approval. Details of the extent, nature and frequency of testing and controls to be performed within the factory production control shall correspond to this control plan which is part of the technical documentation of this European technical approval. The results of factory production control are recorded and evaluated. The records include at least the following information: designation of the products and of the basic materials type of control or testing date of manufacture of the products and date of testing of the products or basic materials or components result of control and testing and, if appropriate, comparison with requirements signature of person responsible for factory production control On request the records shall be presented to the Österreichisches Institut für Bautechnik. 3.2.2 Tasks for approved bodies 3.2.2.1 Initial type-testing of the products For initial type-testing the results of the tests performed as part of the assessment for the European technical approval shall be used unless there are changes in the production line or plant. In such cases the necessary initial type-testing has to be agreed between the Österreichisches Institut für Bautechnik and the approved bodies involved. 3.2.2.2 Initial inspection of factory and of factory production control The approved body shall ascertain that in accordance with the control plan the precautions in the factory, in particular the staff and equipment concerning, and the factory production control are suitable to ensure a continuous and orderly manufacturing of the insulation products with the specifications mentioned in section 2. 3.2.2.3 Continuous surveillance The approved body shall visit the factory at least twice a year for surveillance. It has to be verified that the system of factory production control and the specified manufacturing process are maintained taking account of the control plan. Continuous surveillance and assessment of factory production control have to be performed according to the control plan. 11 The control plan has been deposited at the Österrreichisches Institut für Bautechnik and is handed over only to the approved bodies involved in the attestation of conformity procedure

of European technical approval ETA-06/0076, The results of product certification and continuous surveillance shall be made available on demand by the certification body or inspection body, respectively, to the Österreichisches Institut für Bautechnik. In cases where the provisions of the European technical approval and the control plan are no longer fulfilled the certificate of conformity shall be withdrawn and the Österreichische Institut für Bautechnik informed immediately. 3.3 CE marking The CE marking shall be affixed on the products, the packaging or the attached label. The symbol "CE" shall be accompanied by the following information: identification number of the certification body name or identifying mark of producer and manufacturing plant the last two digits of the year in which the CE marking was affixed number of the European technical approval identification of products (commercial name) density range depending on the area of application settlement water absorption water vapour diffusion resistance airflow resistance declared value of thermal conductivity class of reaction to fire 12 4 Assumptions under which the fitness of the products for the intended use was favourably assessed 4.1 Manufacturing The thermal insulation products shall correspond as far as their composition and manufacturing process is concerned to the products subject to the approval tests. Composition and manufacturing process are deposited at the Österreichischen Institut für Bautechnik. 4.2 Installation 4.2.1 Parameters for the design of construction works or parts of construction works 4.2.1.1 Design value of thermal conductivity The design value of thermal conductivity shall be defined in accordance with the relevant national provisions. 4.2.1.2 Nominal thickness for the thermal resistance calculation When calculating the thermal resistance, the nominal thickness of the insulation layer according to Table 4 shall be applied. Table 4: Nominal thickness depending on the area of application area of application nominal thickness Vertical: machine processed cavity insulation in exterior-, interior walls, clear span of the filled cavity Pitched: machine processed cavity insulation in roofs (pitch >10 ) clear span of the filled cavity Horizontal: machine processed cavity insulation in flat roofs and floor constructions clear span of the filled cavity 12 European classification of reaction to fire of building materials according to the Commission Decision 2000/147/EG of 8 February 2000 implementing Article 20 of Directive 89/106/EEC on construction products.

of European technical approval ETA-06/0076, Horizontal: machine processed exposed insulation not subject to foot traffic on ceiling constructions (pitch 10 ) up to 25 cm 10 % and over 25 cm installation thickness 15 % insulation thickness shall be added to the nominal thickness For horizontal machine processed installation of exposed insulation not subject to foot traffic the insulation layer shall have a constant installation thickness taking into account the nominal thickness. For that purpose suitable height marks shall be arranged in sufficient distances before the processing. When blowing into closed cavities it shall be made sure by appropriate measures (e. g. control drillings) that the cavity is completely filled with the insulating material. 4.2.1.3 Value of water vapour diffusion resistance For evaluating the diffusion equivalent thickness of air layer of the thermal insulation products the value of μ = 1 of water vapour diffusion resistance factor shall be used 13. The construction shall be designed and installed in such a way that no harmful condensation occurs within the works 4.2.2 Parameters for the installation in the construction works or parts of construction works The fitness of the cellulose fibres for the intended use is given under the following condition: Installation carried out by appropriate personnel which have adequate experience in installing the material under the supervision of the person responsible for technical matters on site Installation in accordance with the manufacturer s specifications. Concerning this matter the manufacturer has to train the installers. In case of processing under addition of water it shall be ensured that the main share of water is evaporated before closing the cavity. The time period necessary for this depends on the climatic conditions of the surroundings. Only building materials allowing an evaporation of moisture may be used as facings Precise compression of the cellulose fibres Installation of constructive measurements to avoid settlement by large cavity thickness 4.2.3 Use of the insulation products as airborne sound insulation In case of use of the products as airborne sound insulation it is necessary to determine the airborne sound insulation for the specific construction work in question in accordance with the relevant technical rules in force. 5 Recommendations for the manufacturer 5.1 Recommendations on packaging, transport and storage Packaging of the products has to be such that they are protected against moisture during transport and storage unless other measures are foreseen by the manufacturer for this purpose. 5.2 Recommendations on installation The product has to be protected against moisture during installation. The processing guidelines of the manufacturer have to be followed. 13 For the construction work in question always the less favourable value shall be used.

of European technical approval ETA-06/0076, 5.3 Accompanying information In the information accompanying CE marking the manufacturer shall indicate that the products shall be protected against humidity during transport, storage and installation. Furthermore it is the responsibility of the manufacturer to ensure that the information on the installation procedure is shown clearly on the package and/or on an enclosed instruction sheet. On behalf of Österreichisches Institut für Bautechnik The original document is signed by: Rainer Mikulits Managing Director